The Electromagnetic properties in BiPbSrCaCuO superconductor was studied. In the measurement of current-voltage characteristics, a voltage across the superconducting sample was observed on applying an external magnetic field. The voltage continues to appear the removal of the magnetic field. The appearance of the voltage is ascribed to the trapping of magnetic flux. Depanding on the direction of applied magnetic flux less than 2.5${\times}$10-5 T, the voltage in the magnetized sample increases or decreases. It is considered that mechanism of voltage occurrence can be explained by applying filament model.

The modeled resonant frequency and electrical properties of Pb(Zr, Ti)$O_3$ (PZT) film with various thicknesses have been investigated in film bulk acoustic wave resonators (FBARs). PZT films and Pt electrodes were fabricated by rf-magnetron sputtering. Fabrication process of electrodes and PZT were patterned by simple lift-off process and then back side of silicon was etched by 45wt% KOH. The crystal structure of PZT films with 0.5, 1 and 2 ${\mu}m$ thickness was investigated by x-ray deflection (XRD) and scanning electron microscopy (SEM). The dielectric constant and performance characteristics of PZT FBAR strongly depended on the film thickness. The resonant frequency of PZT films decreased with increasing film thickness. These sputtered PZT FBAR with simple lift-off process enable us to fabricate high Q values with resonant frequencies. (0.71 - 1.48 GHz).

The Pt-doped $SnO_2$ thin film for CO sensor applications obtained by RF sputtering from a target of the same compound in an Ar-$O_2$ atmosphere. Pt-SnO2-SiC Schottky diode detection of CO gas Cause the remarkable change in electrical resistivity of the semiconductor. the good gas sensitivity is shown when annealing condition is 600$^{\circ}C$, 1hr in RTP and detected temperature is 350$^{\circ}C$.

Liquid-immersed pole transformers have utilized an insulation system consisting of natural cellulose-based materials and mineral oil for many years. If the transformers are installed with the abruptly changing load over limitation, its insulation materials are apt to unexpected aging with high temperature. Therefore we have been conscious of developing a transformer that is more thermally stable then conventional types. To measure temperature distribution in the winding of conventional and newly designed transformers, temperature sensors were installed fordirect reading of oil and conductor temperatures at transformers. And we conducted accelerating aging test for these transformers. The measuring data had made use of the design to hybrid insulation system. Also we could find the possibility of this insulation system to apply in pole mounted transformers.

In this paper, we researched the dielectric properties and voltage dependence on slice XLPE sheet from 22[kV] and 154[kV] power cable. We studied effects for impurities and water for semiconductor shield through a dielectric properties experiment to estimate performance of insulating materials in power cable. Capacitance and tan${\delta}$ of 22[kV], 154[kV] were 53/43[pF] and $7.4{\times}10^{-4},\;2.1510^{-4}$. In these results, the trend was increased with the increase of temperature. The tan${\delta}$ of XLPF/ semiconductor layer was increased as compared with that of XLPE. Dielectric properties reliability of tan${\delta}$ was small.

BCP의 이온화에너지 (Ionization Potential; IP)는 5.72ev와 전자친화도 (Electron Affinity; EA)는 2.85ev이며, PEDOT의 IP=5.74ev와 EA=3.3sev이고, TAZ의 IP=6.45ev와 EA=2.77ev, TPD는 IP=5.75ev와 EA=2.S8eV를 나타내었다. 그리고 BCP와 TAZ는 산화전위의 시작점과 증가곡선의 전위 변곡점과의 차이(정공층 갭)와 환원전위의 시작점과 변곡점의 차이(전자층 갭)가 서로 비슷하였으며, PEDOT과 TPD의 경우 정공층의 갭이 전자층의 갭보다 크게 나타났다.

유기발광 소자의 전공 수송층 재료로 많이 쓰이고 있는 N,N'-diphenyl-N,N'-(3-methylphenyl)-1,1'-biphenyl-4-4'-diamine(TPD)는 OLED소자가 연속적으로 작동하게 되면 TPD박막이 결정화되는데, 이러한 결정화는 디스플래이 소자에 dark spot(흑점)의 문제점을 가져왔다. 이러한 원인을 제거하기 위해서 ITO위에 PolyThiophene을 완충층으로 제작함으로써, OLED 소자의 효율에 미치는 영향은 크다고 할수 있다. 자체 제작한 플라즈마 중합장치의 중합조건과 중합체 PolyThiophene의 분자구조를 알아보았다.

OLED(organic light-emitting diode)소자에 사용되는 ITO(Indium-tin oxide)전극에 Ar/$O_3$ 플라즈마 표면처리 함으로써 ITO전극에 표면상태의 개선에 좋은 영향을 미치는 것으로 나타났다. 13.56MHZ RF 플라즈마 장치를 이용하여 Ar/$O_3$ 플라즈마 처리한 후 AFM(atomic force microscopy)측정을 통해 표면 morphologyjroughless를 분석하고, XPS(X-Ray Photoelectron Spectroscopy)분석을 통해 표면의 화학적 조성비 분석을 수행 하였다.

An alumina membrane with nano-sized pores was fabricated by anodic oxidation. The shape and structure of the pore on alumina membrane were changed according to the roughness of aluminum surface. The shape and structure of the nano-sized pre were investigated according to purity of aluminum substrate for the anodization process. The aluminum substrates with 99.5% and 99.999% purities were used. The aluminum substrate(99.5%) was anodized after the processes of pressing, mechanical polishing, chemical polishing, and electrochemical polishing. The nano-sized pores with the pore size of 50 - 100nm, the cell size of 20-50nm and the thickness of $10{\mu}m{\sim}45{\mu}m$ were obtained. Even though the electrochemical polishing was used for the aluminum substrate (99.999%), the same characteristics as the aluminum substrate (99.5%) was obtained. The alumina membrane prepared by anodization for 5 min using fixed voltage method shows the pore with irregular shape. The pore shape was changed to regular shape after pore widening process.

The alumina membrane with nano sized pore was prepared from aluminum by anodic oxidation to apply for storage equipment, gas sensor and stamper. The pore size and cell size of the pores are controlled by anodic oxidation voltage. The alumina thickness was controlled by etching process using 0.2M $H_3PO_4$. The thickness of alumina on Si wafer was very accurately controlled by anodic oxidation time. Nickel with nano-sized grain was electroplated on the Au layer on silicon wafer. The fabricated pores on alumina membrane was the thickness of $7{\sim}10{\mu}m$ with straight nano-sized pore of 307${\sim}$120nm. The alumina by the etching process shows smooth surface. The size of Ni grain was 130nm and 250nm for 10mA/$cm^2$and 20mA/$cm^2$of electroplating currents, respectively.

바이오센서는 효소(enzyme), 생분자(biomolecule), 항체(antibody), 세포(cell) 등의 biological agent를 인지 물질(recognition material)로 하여 측정하고자하는 분석 대상(analyte)과 높은 선택성으로 반응을 일으키게 하여 그 결과를 기존의 물리, 화학센서로 감지 해내는 방식이므로 기존의 의료용 화학센서를 대체하는 추세이다. 바이오센서가 기존의 센서와 구별되는 점은 생물질의 선택적인 반응 및 결합을 이용하는 것이므로 바이오센서의 실용화에 있어서 가장 중요한 것은 생체 반응 물질의 고정화 기술과 고정화막의 선택이라 할 수 있다. 일정전압법을 이용한 요소센서는 많이 연구되어 오고 있으나 낮은 농도에서의 감도저하에 따른 단점으로 상용화에 이르지 못하고 있다. 본 논문은 요소센서의 이용하기 위한 고정화막으로 3-mercaptopropionic acid 자기조립 단인층의 전기화학적 특성을 고창하였다. 자기조립 단일층은 직접적인 전자전달로 인하여 낮은 요소 농도에서 뛰어난 강도와 빠른 반응 시간을 보였으며, 특히 다공질 실라콘을 기질로 사용한 경우 평면 전극 보다 약 3배의 감도 증가 효과를 가져왔다. 자기조립 단일층의 표면 분석은 X-ray photoelectron spectroscopy(XPS)를 이용하였다.

The microstructure, electrical, and clamping voltage characteristics of ZPCCY-based varistor ceramics were investigated in the sintering time range of 1${\sim}$3 h. Increasing sintering time promoted the densification, in which the average grain size and density are increased in the range of $11.4{\sim}16.0{\mu}m$ and $5.34{\sim}5.54g/cm^3$, respectively. The nonlinear exponent decresed in the range of 60${\sim}$26 and the leakage current increased in the range of $1.3{\sim}10.7{\mu}A$ with increase of sintering time. The clamping voltage ratio was less than 2 for ratio surge current of 10 A over sintering times.

이중 에피층 구조를 가지는 SOI(Silicon-On-Insulator) LIGBT(Lateral Insulated Gate Bipolar Transistor)의 에피층 두께 변화에 따른 항복전압 특성을 분석하였다. 제안된 소자는 전하보상효과를 얻기 위해 n/p-epi의 이중 에피층 구조를 사용하였으며, 에피층 전체에 걸쳐서 전류가 흐를 수 있도록 하기 위해 trenched anode구조를 채택하였다. 본 논문에서는 n/p-epi층의 농도를 고정시킨 후 각각의 epi층의 두께를 변화시켜가며 simulation을 수행하였을 때 항복전압의 변화 및 표면과 epi층에서의 전계분포변화를 분석하였다.

The composites were fabricated, respectively, using 61vol.% SiC - 39vol.% $TiB_2$ and using 61vol.% SiC 39vol.% WC powders with the liquid forming additives of 12wt% $Al_2O_3+Y_2O_3$ by pressureless annealing at 1800$^{\circ}C$ for 4 hours. Reactions between SiC and transition metal $TiB_2$, WC were not observed in this microstructure. The result of phase analysis of composites by XRD revealed SiC(6H), $TiB_2$ and YAG($Al_5Y_3O_{12}$) crystal phase on the SiC-$TiB_2$, and SiC(2H), WC and YAG($Al_5Y_3O_{12}$) crystal phase on the SiC-WC composites. ${\beta}{\rightarrow}{\alpha}$-SiC phase transformation was ocurred on the SiC-$TiB_2$, but ${\alpha}{\rightarrow}{\beta}$-SiC reverse transformation was not occurred on the SiC-WC composites. The relative density, the flexural strength showed respectively value of 96.2%, 310.19Mpa in SiC-WC composites. The electrical resistivity of the SiC-$TiB_2$ and the SiC-WC composites is all positive temperature cofficient resistance(PTCR) in the temperature ranges from 25$^{\circ}C$ to 500$^{\circ}C$.

압력센서는 몇 가지 센싱 메카니즘을 가지고 있으므로 종류가 다양하고 크기 변에서도 여러 가지가 이용되고 있다. 최근에는 센싱 부분이 작으며 제어부분도 포함되는 ASIC화된 센서 시스템이 개발되고 있다. 여기에 이용되는 대부분의 탄성물질은 힘을 받았을 때 물질 내부의 벌크에서 저항 값이 변화하는 특성을 갖고 있다. 이러한 특성은 피에조 저항률(piezoresistivity)로 언급되며 스트레인 게이지의 감도에 영향을 주는 중요한 요소로 작용한다. 다이어프램으로 금속대선 세라믹을 사용하면 안정성이 우수한 특정을 가칠 수 있으며, 부식성 가스 류 및 화학성분에 대해서 내성이 강하고 환경변화에 따른 변형과 공정의 단순화 등 우수한 특성을 갖고 있는 것이 큰 장점이다. 센싱부는 산화 루세니움($RuO_2$)을 주 성분으로 하는 분말을 Paste화 하여 다이어프램 위에 스크린 프린팅을 하여 기본성능을 나타내었으며 특히, 상품화에서 중요한 일반성능에서는 온도 특성에 대한 Span 과 Offset 그리고 공정의 단순화에 대해서 고찰을 하였다.

Film bulk acoustic resonator (FBAR) devices which adopt a membrane-type configuration are fabricated by a novel process. In contrast to the conventional FBAR structure, the newly fabricated resonator doesn't employ any supporting layer below or above it, so that the properties of piezoelectric layer are not influenced by the bottom electrode material. FBAR devices with Mo/AlN/Metal configuration are also fabricated. The frequency response characteristics ($S_{11}$) of the devices fabricated using the proposed process are compared with those of the conventional devices. The return losses are also estimated, in terms of the kind and thickness of bottom electrode materials.

Carbon nanotubes (CNTs) are grown on the TiN-coated silicon substrate by varying the thickness of Ni and Invar426 catalyst layers at 600$^{\circ}C$ using an inductively coupled plasma-chemical vapor deposition (ICP-CVD). The Ni and Invar426 catalysts are formed using an RF magnetron sputtering system with various deposition periods. Characterization using various techniques, such as FESEM, HRTEM, and Raman spectroscopy, shows that the physical dimension as well as the crystal quality of grown CNTs are strongly changed by the kind and thickness of catalyst materials. It is also seen that Ni catalysts would be more desirable for vertical-alignment of CNTs compared with Invar426 catalysts. However, the CNTs using Invar426 catalysts display much better electron emission capabilities than those using Ni catalysts. The physical reason for all the measured data obtained are discussed to establish the relationship between structural properties and field-emissive properties of CNTs.

As the integrated circuit device shrinks to the smaller dimension, the chemical mechanical polishing (CMP) process was required for the global planarization of inter-metal dielectric(IMD) layer with free-defect. The effect of alternative commerical slurries pads, and post-CMP cleaning alternatives are discuess, with removal rate, scratch dentisty, surface roughness, dishing, erosion and particulate density used as performance metrics. we investigated the performance of $SnO_2$-CMP process using commonly used silica slurry, ceria slurry, tungsten slurry. This study shows removal rate and nonuniformity of $SnO_2$ thin film used to gas sensor by using Ceria, Silica, W-Slurry after CMP process. This study also shows the relation between partical size and CMP with partical size analysis of used slurry.

Single phase $CuInS_2$ thin film with a highest diffraction peak (112) at a diffraction angle ($2{\theta}$) of 27.7$^{\circ}$ was well made by SEL method at annealing temperature of 250 $^{\circ}C$ and annealing hour of 60 min in vacuum of $10^{-3}$ Torr or in S ambience for an hour. And the peak of diffraction intensity at miller index (112) of $CuInS_2$ thin film annealed in S ambience was shown a little higher about 11 % than in only vacuum. Single phase $CuInS_2$ thin films were appeared from 0.85 to 1.26 of Cu/In composition ratio and sulfur composition ratios of $CuInS_2$ thin films fabricated in S ambience were all over 50 atom%. Also when Cu/In composition ratio was 1.03, $CuInS_2$ thin film with chalcopyrite structure had the highest XRD peak (112). And lattice constant a and grain size of the thin film in S ambience were appeared a little larger than those in only vacuum. The largest lattice constant of a and grain size of $CuInS_2$ thin film in S ambience was 5.63 ${\AA}$ and 1.2 ${\mu}$m respectively. And the films in S ambience were all p-conduction type with resistivities of around $10^{-1}{\Omega}cm$.

압전재료의 분극공정에서 제어되는 인가전압, 유지시간 및 온도 변수들에 대한 최적의 조건을 확립하기 위해 Rosen형 안전 변압기를 설계 및 제조하여 특성분석 하였다. 분극처리를 위한 분극전계, 온도, 유지시간 등의 외부 에너지가 증가할수록 쉽게 분극되어 포화현상이 나타났으며, 140$^{\circ}C$ 이상의 온도에서 4kV/mm의 분극전계로 3분 이상 분극시키면 최대 전압 이득을 얻을 수 있다. 또한 부하저항이 증가할수록 공진주파수는 고주파 방향으로 이동하며, 공진전류가 증가하여 전압이득이 증가하였다.

The piezoelectric ceramics for AE-sensor are desired large electromechanical coupling factor, high mechanical quality factor and good characteristic resonance frequency. In this study, the empirical formula of specimens is used 0.9Pb$(Zr_xTi_{1-x})O_3-0.1Pb(Mn_{1/3}Nb_{1/3}Sb_{1/3})O_3$ (PZT-PMNS). The piezoelectric and dielectric characteristic are investigated by sintering temperature and value of x as functions of $Ti^{2+},\;Zi^{2+}$ moi rate. MPB(morphotropic phase boundary) is defned in the x=0.522. Because it is appeared to the best piezoelectric and dielectric characteristic in the x=0.522, it can be application of AE sensor. PZT-PMNS ceramics without pre-amplifier and filter are tested for AE-signal of PD and arc detecting. The detection characteristic is evaluated wave form, frequency distribution.

5 mol% $BaWO_4$를 첨가시켜 합성한 Ba$(Mg_{1/3}Ta_{2/3})O_3$를 이용하여 비방사유전세선로에 삽입되는 세라믹스 공진기를 제자하고 기존의 $MgTiO_3-CaTiO_3$계 세라믹스 공진기와 공진특성을 비교하여 그 특성을 고찰하였다. 그 결과 BMT 세라믹스는 기존의 $MgTiO_3-CaTiO_3$계 세라믹스보다 품질계수가 2배 이상 크게 높게 측정되었고, 측정 사진의 관찰 결과 전파차단성도 우수할 것으로 예상되기 때문에 BMT가 비방사유 전체선로에 삽입되는 유전체 공진기 재료로서 적용될 경우 우수한 공진특성을 발휘할 것으로 판단된다.

The $Pb(Zr_{0.4}Ti_{0.6})O_3/Pb(Zr_{0.6}Ti_{0.4})O_3$ [PZT(4060)/(6040)] multilayered thin films were deposited by RF Sputtering method on the Pt/Ti/$SiO_2$/Si substrate. This procedure was repeated several times to form PZT(4060)/(6040) heterolayerd thin films. The effects on the structural and dielectric properties of PZT multilayered thin films were investigated. The MFM(Metal Ferroelectric Metal) type capacitors were made using the PZT(4060)/(6040) multilayered thin films deposited with optimum deposition condition. An enhanced dielectric property was observed in the PZT(4060)/(6040) multilayered thin films. The relative dielectric constant and dielectric loss at 100Hz of the PZT(4060)/(6040)-5 multilayered thin films were about 1106 and 0.016, respectively.

The $Pb(Zr_{0.52}Ti_{0.48})O_3/(Ba_{0.6}Sr_{0.4})TiO_3$ [PZT(52/48)/BST(60/40)] heterolayered thin films were deposited on Pt/Ti/$SiO_2$/Si substrates by using the RF sputtering method with RF powers of 60,70,80,90[W]. All thin films showed the peaks of the tetragonal phase. Increasing the RF power, dielectric constant and loss of the PZT(52/48)/BST(60/40)] heterolayered thin films were decreased. The thickness ratio of PZT and BST thin films was 1/1. The relative dielectric constant and the dielectric loss of the PZT(52/48)/ BST(60/40) heterolayered thin films were 562 and 13%, respectively.

This study was to measure the minuteness structure, piezoelectric properties of (0.3-x)PMN- xPSS -0.7PZT+0.5[wt%]NiO+0.5(wt%)$MnO_2$ (x=0.05, 0.10, 0.15, 0.20, 0.25)ceramics according to sintering temp- erature and PSS(mol%) after manufacturing the specimens with a general method. the results of this study were gotten such as follows. The crystal structure of ceramic has the rombohedral structure in XRD. It appeared that addition of Ni, Mn additive was helpful to the formation of stable structure. The electrome- chanical coupling coefficient(kp) showed good properites on the whole, showed its maximum value 25.94[%] in specimens sintered at 1100[$^{\circ}C$], x=0.25mol. The mechanical quality coefficient(Qm) showed its maximum value 272.42 in specimens sintered at 1150[$^{\circ}C$], x=0.05mol. and was decreased by increasing PSS[mol%] The temperature coefficient of the resonant frequency(TCFr) showed stable properties in all sintering temperature with x=0.05mol. Especially good stability of 0.0054[%/$^{\circ}C$] showed in specimens sintered at 1100$^{\circ}C$, x=0.05mol.

ZnO thin films on (001) sapphire substrates have been deposited by pulsed laser deposition(PLD) technique using an Nd:YAG laser with a wavelength of 266nm. Before post-annealing treatment in the oxygen ambient, the experiment of the deposition of ZnO thin films has been performed for substrate temperatures in the range of $300{\sim}450^{\circ}C$ and flow rate of 100${\sim}$700 seem. In order to investigate the effect of post-annealing treatment of ZnO thin films, films have been annealed at various temperatures after deposition. After post-annealing treatment in the oxygen ambient, the structural properties of ZnO thin films were characterized by X-ray diffraction(XRD) and the optical properties of the ZnO were characterized by photoluminescence(PL).

The surge current characteristics of ZnO-$Pr_6O_{11}$-CoO-$Cr_2O_3-Dy_2O_3$-based varistors were investigated with various $Dy_2O_3$ contents. The sintered density decreased in the range of $5.2{\sim}4.6g/cm^3$ with increasing $Dy_2O_3$ content. The incorporation of $Dy_2O_3$ markedly enhanced the nonlinear properties of varistors above 10 times in nonlinear exponent, compared with the varistor without $Dy_2O_3$. The varistor ceramics doped with 0.5 mol% $Dy_2O_3$ exhibited the highest electrical stability. However, the remainder varistors resulted in thermal runaway due to low density of varistor ceramics. The clamping voltage ratio exhibited a minimum value of 2.03 in 1.0 mol% $Dy_2O_3$ at surge current of 100 A(8/20 ${\mu}s$).

반도체 웨이퍼의 면저항을 정밀 측정하는 대표적인 두가지 방법인 4탐침(four point probe)방법과 van der Pauw방법으로 반도체 웨이퍼의 면저항을 비교평가 하였다. 4탐침방법에 의한 측정 시스템을 사용하여 웨이퍼의 전체 면에 대하여 면저항을 측정하고, 같은 웨이퍼의 가장자리 네 지점에 탐침 전극을 구성한 후 van der Pauw 방법으로 면저항을 측정한 결과 4탐침 방법에 의한 측정결과를 기준으로 1 %이하의 일치도를 나타냈다.

In order to analyze the physical and chemical characteristics of the home production porcelain insulators by change of the alumina addition amount, 36000lbs ball socket type suspension insulators which were manufactured in 1989, 1995 and 2001 removed in transmission line and an experiment was performed. By the result, 8 [wt.%] alumina that influences the mechanical properties and arc resistance properties in case of insulators that were manufactured in 1989 was contained, and the relative density and the fracture toughness of insulators appeared by 94.2% and 1.4 [MPa $M^{1/2}$], respectively. However, 12 [wt.%] alumina was contained in case of insulators that were manufactured in 1995, and the relative density and the fracture toughness of insulators appeared preferably lower by 92% and 1.3 [MPa $M^{1/2}$], respectively. Amount of alumina was contained most by 17 [wt.%] in case of insulators that were manufactured in 2001. It was confirmed that the electrical and mechanical characteristics such as the relative density and the fracture toughness appeared excellently by 96% and 1.7 [MPa $m^{1/2}$], respectively.

현재 국내에서의 견인전동기 개발현황은 직류전동기는 655kw, 교류전동기는 210kw정도이며, 주행속도가 200km/h이상인 고속에 적용되는 1,000kW급 이상 유도전동기 기술은 한국형 고속전철이 국내에서는 최초이다. 최고 주행속도 300km/h급의 고속전철용 1,130kW 동기전동기에 대한 제작 및 시험기술만을 프랑스에서 이전 받아 유도전동기를 제작하였다. 고속철도 차량용 견인전동기는 한정된 공간에 취부되어야 함으로 경량화가 필수적이다. 또한 전력기기에 대한 에너지 고밀도화가 가능해야 함으로 열적 특성에 대한 분석이 체계적으로 이루어져야 한다. 본 연구를 통해 외기 온도, 주행 속도 및 운행 시간에 따른 견인전동기의 온도 특성 변화를 살펴봄으로써 고속전철용 견인전동기의 고정자 온도 특성을 확인할 수 있었다.

변압기는 판토그래프를 이용하여 가선으로부터 전력을 공급받아 전력변환장치, 견인전동기 등의 각종 장치에 필요한 전원을 공급해주는 중요한 역할을 한다. 또한 전장품에서 가장 무겁고 부피가 큰 변압기는 차량의 주행 속도에 큰 영향을 미치고 변압기를 설치할 수 있는 공간상의 제약이 따르므로 소형, 경량화가 매우 필수적이다. 본 논문에서는 변압기의 오일온도와 외함온도의 변화를 확인하기 위해 차량에 취부된 변압기에 온도 센서를 부착하였다. 또한 한국형 고속전철이 운행하는 동안 변압기의 온도가 기준 온도를 넘어갈 경우 차량의 치명적인 고장을 일으킬 수 있으므로 차량 내에 상시 계측시스템을 설치하여 변압기의 온도를 실시간으로 감시하고 측정하였다. 이를 통해서 변압기의 온도 변화와 열적 특성을 분석할 수 있었다.

수입외자재에 의존하고 있는 GIS(Gas Insu.lated Switchgear)용 FRP 절연로드의 전기적, 기계적 신뢰성시험에 대하여 언급하고자하며, 본 논문에 기술된 신뢰성시험을 통하여 제품특성을 재확인하였으며 최소 GIS의 수명과 동일함을 확인, 파악함으로써 국산화 개발을 실현하였다.

The piezoelectric ceramic is attached between 'L' type guide and 'L' type stator. This motor has rotary motion which is operated by the travelling wave. The basic structure of the two kinds of type motor that called one stator motor, two stator motor is same but we suggested a few parameters for considering their stator design and characteristics. As a result, the two stator type motor is much more useful than one stator type motor for bi-direction rotation.

초고압 지중 케이블을 전기적, 기계적으로 연결하는 역할을 하는 중간 접속함은 미가교 폴리에틸렌을 사용하여 현장에서 가교시키는 TMJ(tape molded Joint), 에폭시와 EPDM고무의 복합 절연구조를 가지고 있는 PJ(Prefabricated Joint), 그리고 EPDM또는 실리콘 고무를 단독으로 사용하는 PMJ(Premolded Joint)로 대표된다. 그러나 TMJ는 현장에서 가교하는 방식으로 조립 후 품질을 파악하기가 쉽지 않으며 PJ는 공장에서 미리 성형한 제품을 현장에서 조립만 하면 되는 구조이나 그 부품의 수가 많고, 이종 계면을 가지고 있는 복합절연구조를 가지고 있어 최근에는 부품의 수도 적고 조립이 간편하며 이종 계변의 수를 최소화하여 전기적 안정성을 높인 조립형 접속함인 PMJ를 선호하는 경향을 보이고 있다. 본 논문에서는 PMJ용으로 사용되는 실리콘 고무의 절연과 반도전 계면에서의 접착력과 전기적 파괴 특성간의 상관 관계를 규명하였고 또한 실리콘 고무의 상온 및 고온에서의 AC 및 Impulse 전압의 특성 변화와 Impulse 전압의 극성효과에 대해 규명하였다.

The electrical fire frequently happens through carelessness of a vinyl and rubber cords such as a poor contact, a mechanical stress and so on. Electrical fire occupies the greater part(about 30%) of all fires in Korea. In this paper, we compared to the fire dispersive patterns of vinyl and rubber cords according to the external flame in the wall-model. The fire progress and dispersive patterns were measured by a high speed imaging system(HG-100K, REDLAKE, USA). From the results, short-circuit of the vinyl cords are easy to happen than the rubber cords by the external flame. The pattern of fire was progressed a flashover, scattering and disconnection. The fire progress on the vinyl cord is not observed because the ignition energy decreases. However, the fire was progressed continuously on the rubber cord.

Use of higher voltage and higher capacity of power systems and their equipment is leading to an increase in the size of the entire system. In order to reduce the cost of constructing a substation, it is necessary to reduce the size of equipment. So, this paper described optical sensor, which exploited the electric and magnetic potentiometer to sense the measured voltage and current of medium voltage GIS. It can be used both in measurement and in protection relays as its well linearity, rapid response, broad dynamic range, wide frequency band, no magnetic saturation, small in volume, light weight, and saft in insulation.

The effect of the triblock copolymer poly[styrene-b-(ethylene-co-butylene)-b-styrene](SEBS) on the formation of space charge of immiscible low density polyethylene/polystyrene(LDPE/PS) blends was investigated. The amount of charge accumulated in the 70/30(wt%) LDPE/PS blends decreased when the SEBS content increased up to 10 wt%. For compatibilzed and uncompatibilized blend, morphological observation showed that the addition of SEBS results in the domain size reduction of the dispersed PS phase and a better interfacial adhesion between LDPE and PS phases. The location of SEBS at a domain interface enables charges to migrate from one phase to the other via domain interface and therefore, results in a significant decrease in the amount of space charge for the LDPE/PS blends with SEBS.

This paper describes the use of Armaid papers and varnishes in electric motors. We compare with boundary element method(BEM) and finite element method(FEM) by calculated electric field strength. Several computer software package to perform such calculations based on electrostatic field and applicable DC are available.

In this paper, the elastic epoxy added elastomer having viscoelasticity to existing epoxy was measured thermal, structural properties by DSC (Differential Scanning Calorimetry) and FESEM (Field Emission Scanning Electron Microscope). Specimens were made of dumbbell forms by the ratio of 5, 10, 15, and 20[phr] by regulation with elastomer contents. The measurement temperature dimensions of DSC were -20[$^{\circ}C$] to 150[$^{\circ}C$] and rising temperature was 4[$^{\circ}C$/min]. Also we observed structure through FESEM at the magnification of 1000 times with the voltage of 15[kV] after breaking by quenching specimens. As experimental results, we could know that thermal and structural properties were improved quantity according to decrease of elastomer contents. Namely, it increased glass transition temperature, high temperature, and matrix structure. In general, thermal, structural properties of 15[phr] was excellent among the specimens.

XLPE compound have used for insulation of 22.9kV power cable. XLPE insulation is aged for use long time in distribution line. The cause of aging is water tree is happening and growth. Accelerated water tree test method are Accelerated volatge aging method and high frequency aging method. In this paper, high frequency accelerated water tree was performed. And the result was analysed AC breakdown voltage and size and number of water trees.

The design, modeling and measurement of RF switch module for GSM applications is presented in this paper. RF switch module is constructed using a LTCC multi-layer switching circuit and integrated low pass filter. Insertion and return loss of the low pass filter were designed less than 0.3 dB and better than 12.7 dB at 900 MHz. The RF switch module contained 10 embedded passives and 3 surface mount components integrated on $4.6{\times}4.8{\times}1.2$ mm, 6-layer multi-layer integrated circuit. The insertion loss of switch module was measured at 900 MHz was 11 dB.

Class-F resin-rich type insulating tapes are generally used for the groundwall insulations of the large turbine generators with air-cooled and hydrogen-cooled stator windings. In this paper, mechanical strength properties degraded over aging time in higher temperature than designed one in normal condition were experimentally investigated and the results of comparative tests were presented on the existing class-F resin-rich type tape and a developed one after curing. The resin-rich insulating tapes with composite material of Mica/Epoxy/support currently were used in this test. The tests for tensile and flexural strength properties were conducted with the specimens which were composed of unaged and the aged specimens accelerated for one, two, and three thousand hours at 180 $^{\circ}C$. The tensional strength was only measured for the unaged specimens and the results are also presented to make a comparative test for their initial mechanical characteristics.

Class-F and B resin-rich type insulating tapes are generally used for the ground wall insulations of respective air-cooled and water-cooled stator windings in larger turbine generators. In this paper, their electrical properties coupled with aging times in higher temperature than designed one in normal condition were experimentally investigated and the results of two comparative tests were presented on the existing class-F resin-rich type tape and a developed one after curing. The resin-rich tapes currently used arc composed of six and a half 3-layer sheets that arc structured with mica paper, the top and bottom supports of it respectively, and the epoxy resin to bind them tightly. The results for breakdown voltage and strength on the cured specimens were presented, which were composed of the unaged, the aged accelerated for one, two, and three thousand hours at 180 $^{\circ}C$. The surface and volume resistivities on them were measured and the results are also presented to make a comparative test for the initial electrical characteristics.

In this study, the surface properties of PET film were analyzed after plasma surface treatment. After plasma treatment of surface roughness and XPS were evaluated to analyze the chemical property, while the surface potential decay and surface resistivity was measured to analyze the electrical characteristic. When plasma discharge treatment was conducted for less than 10 minutes, the electrical insulating property was found to be improved through evaporation of low molecular weight materials and cleaning of surface. However, when the treatment was conducted for more than 10 minutes, the insulating property was decreased due to excessive discharge energy. Analysis of chemical characteristics showed that 10-minute treatment resulted in increase of C-O and O=C-O. However, when treated for more than 10 minutes, they were relatively decreased.

초고압 케이블의 절연물질로 널리 사용되고 있는 가교 폴리에틸렌의 전기적 특성은 라멜라 결정 조직의 밀도와 라멜라 조직의 성장방향과 밀접한 관련이 있는 것으로 알려지고 있다. 본 연구에서는 반도전 물질에 계면활성제를 첨가하고, 제조 온도를 제어하여 폴리에틸렌의 미세 조직을 변화시킴으로써, 라멜라 조직이 전기적 특성에 미치는 영향을 분석하였다. 전기적 특성은 절연파괴 전압을 측정하였고, TEM 분석을 통하여 폴리에틸렌의 모폴러지 분석을 하였으며, XRD 분석을 통하여 라멜라 조직의 밀도를 분석하였다.

초고압절연케이블의 온도변화에 따른 절연특성을 연구하였다. 온도변화는 상온, 50, 80[$^{\circ}C$]로 변화시켰으며, 전압은 0.5[kV]씩 스텝인가법에 의해 승압시켰다. 또한 보이드 특성을 위해 내부에 보이드를 삽입하였다.

전해질 용액 중에서 내부 이온화산에 의한 드리프트 특성이 거의 없는 장기안정성과 pH 농도 감지 특성이 우수하지만 알칼리 금속 양이온 감지특성이 열악한 silicon nitride 박막의 이온 감지특성을 변화시키기위하여, 저온화학기상증착법(LPCVD)으로 제작된 silicon nitride 박막에 B 및 Cs를 이중이온주입시켰다. 이온수입이 되지 않은 silicon nitride 박막과 B 및 Cs가 이중이온주입된 박막의 전해질 용액 중 pH, pNa, pK, pRb 및 pCs 농도 감지특성을 조사하여 비교하였다. 이중이온주입된 샘플은 이온주입이 되지 않은 샘플에 비해 그 전해질 용액 중 pH 농도 감지도가 현저히 감소한 반면, 전해질 용액 중 알카리 금속이온농도 감지도는 이온주입되지 않은 샘풀에 비해 현저히 증가하는 특성을 보였다.

$Si_3N_4$ 박막을 동일한 공정 파라메터로 저압 화학기상증착법(LPCVD)으로 증착하고, IS, LOCOS- IS 및 ISFET의 세 가지 각각 다른 구조로 하여 용약 중 pH 농도 감지용 센서소자를 제작하였다. 이 세 가지 다른 센서소자에 대하여 pH 농도변화에 따른 감지도, 감지특성곡선의 선형성, 히스테리시스 등 주요 특성을 각각 조사한 후 비교 분석하였다. LOCOS-IS 구조의 pH 센서는 ISFET 구조의 pH 센서와 유사한 우수한 제반 pH 감지특성을 보였으나, 간단한 IS 구조의 pH 센서는 이들에 비해 상대적으로 열악한 pH 감지특성을 보였다. 동일공정으로 제작된 Si3N4 박막으로 제작되었음에도 불구하고 간단한 IS 구조의 pH 센서의 비교적 열악한 특성을 보이는 원인을 규명하기 위하여, pH 농도 변화에 따른 C-V특성 변화에 의한 pH 감지특성 조사시의 IS 및 LOCOS-IS 구조의 정전용량의 변화를 비교하고 고찰하였다.

In this investigation, we have studied the diffusion of the $Cu^+$ ion in the Cu/Ta/SiOCH/Si and Cu/Ta/$SiO_2$/Si MIS-C structure. The Cu ions diffusion into the Ta barrier and SiOCH was examined by shift in flatband voltage of capacitance-voltage measurement and leakage current of current-voltage measurement. These evalution indicated that $Cu^+$ ion diffusion rate in Ta/SiOCH is considerably lower then the Ta/$SiO_2$ structure. And diffusion barrier Ta(50[nm]) is useful barrier against $Cu^+$ ion diffusion up to 450$^{\circ}C$.

Diamond films including nanocrystallites are grown by microwave plasma chemical vapor deposition using $O_2$ additives and negative substrate bias at growth step. Effects of growth parameters on film properties are characterized by Raman spectra, SEM, and AFM images. It is found that the surface roughness and the microstructure of grown films can be controlled by changing $O_2$ gas ratio. The I-V characteristics are also investigated in terms of growth conditions of diamond films. The surface roughness and the $sp^2$ phase of the grown diamond films turn out to be crucial factors for reducing leakage currents at diamond/metal interfaces.

New luminescent material, 6.11-dihydoxy-5.12-naphtacene-dione $Alq_3$ complex($Alq_2$-Ncd), 1.4-dihydoxy-5.8-naphtaquinone $Alq_3$ complex ($Al_2Nq_4$) was synthesized. The $Alq_2-$ Ncd and $Al_2Nq_4$ has big molecular weight and many ${\pi}$-electrons more than widely known $Alq_3$. And extended efforts have been made to obtain high-performance electro luminescent(EL) devices. We used hole transfer layer of powdered TPD to improve hole transfer and characteristics of interface in OLED. This study indicates not only the sterical effect but also some other effects that would be responsible for the change of the emission wavelength. improvement of luminance and etc.

This paper reports the stability against surge of ZnO-$Pr_6O_{11}$-CoO-$Cr_2O_3-Er_2O_3$-based varistors sintered at different sintering temperatures. As sintering temperature increases, the varistor voltage decreased in the range of 412${\sim}$266 V and the nonlinear exponent decreased in the range of 61${\sim}$50. Meanwhile, the stability against surge with surge peak current of 100 $A/cm^2(8{\times}20{\mu}s)$ exhibited to be good on the whole.

3,4-ethylenedioxythiophene(EDOT)을 ferric-toluenesulfonate(FTS)로 doping하여 합성하였다. 이때 다양한 유기용매를 함께 첨가하여 합성하였고, 온도에 따른 각각의 DC 전도도를 측정하였다. FTS로 dofing된 poly(3,4-ethylenedioxythiophene) (PEDOT)는 3-D variable range hopping model을 잘 따르며, alcohol류의 용매와 함께 합성한 경우는 상온의 DC 전도도가 2 S/cm로 0.4 S/cm의 reference 보다 전기전도를 증가시키는 반면, ketone류는 약 $10^{-11}$ S/cm로 전기전도를 감소시키는 경향을 보였다. 전도도의 증감과 doping level의 관계를 규명하기 위하여 X-ray 분석을 하였다.

During the last 20 years organic semiconductors have attracted considerable attention due to their interesting physical properties followed by various technological applications in the area of electronics and opto-electronics. It has been a long time since organic solar cells were expected as a low-cost energy-conversion device. Although practical use of them has not been achieved, technological progress continues. Morphology of the materials, organic/inorganic interface, metal cathodes, molecular packing and structural properties of the donor and acceptor layers are essential for photovoltaic response. We have fabricated solar cell devices based on zinc-phthalocyanine(ZnPc) as donor(D) and fullerine($C_{60}$) as electron acceptor(A) with doped charge transport layers, $Alq_3$ as an electron transport or injection layer. We observed the photovoltaic characteristics of the solar cell devices using the Xe lamp as a light source.

We attempt to investigate morphology of self-assembled dipyridinium dithioacetate on Au(111) substrate by Scanning Tunneling Microscopy(STM). Also, we measured electrical properties using Scanning Tunneling Spectroscopy(STS). Sample that use this experiment acquires thiol function beside quantity by dipyridinium dithioacetate, is structure that can be self-assembled easily to Au(111) substrate. The same self-assembly procedure was used for two different concentrations, 0.5mmol/ml and 1mmol/ml. Dilute density of sample by 0.5mmol/ml, 1mmol/ml and observed dipyridinium dithioacetate's image by STM after self-assembled on Au(111) substrate. The structure of Tip/SAMs/Au(111) has been used measurement for electrical properties(i-v) using STM. The current-voltage measurement result, observed negative differential resistance(NDR) properties.

This paper is focused on the improvement of reflection angle of an optical scanner by changing a shape of a torsion bar attached with an optical scanner reflector(mirror). In order to improve the light efficiency of the optical scanner by virtue of the magnetic effect, which tiny magnets are attached under both ends of the optical scanner reflector. and hence the optical scanner reflector was operated in relatively lower driving voltage. By changing the torsion bar's shape I type into S type, we've got the lower resonant frequency(32.5Hz) of an optical scanner than that of conventional one(50Hz). According to these results. The reflection angle of an optical scanner with magnets was much larger in the range of about 14.8$^{circ}$ without a magnet. By making use of a magnetic actuator instead of a conventional electrostatic actuator, the optical scanner was less influenced from outdoor dust or moisture.

우리는 황토 조명등을 제작하여 원 적외선 발생 실험을 하였다. 실험에는 백열전구 200W, 실내온도 21도, 습도 38%의 조건에서 열화상실험과 TF-IR(적외선 분광방사 측정장치)에 의한 원적외선 방사한도를 측정하였으며, 그 결과 방사율 0.914와 방사에너지 $6.23{\times}10^2\;(w/m^2{\cdot}{\mu}m)$ 가 얻어졌다. 이와 같은 결과로 황토조명등에서 원적외선이 발생한 것을 확인하였다.

Monolayers of lipids on a water surface have attracted much interest as models of biological membranes, but also as precursors of multilayer systems promising many technical applications. Until now, many methodologies have been developed in order to gain a better understand. Photoisomerization in monolayers of a novel azobenzene compound, azobenzene dendrimer, was investigated for the first time by means of the absorption spectrum and Maxwell displacement current (MDC) technique. Dendrimers are well-defined macromolecules exhibiting a tree-like structure, first derived by the cascade molecule approach. According to the absorption spectrum, trans-to-cis conversion ratio was estimated to the third generation of azobenzene dendrimer deposited onto a glass substrate. Temperature-dependent induced charge with trans-cis isomerization was also measured by means of MDC technique.

Chemical mechanical polishing (CMP) process has been widely used to planarize dielectric layers, which can be applied to the integrated circuits for sub-micron technology. Despite the increased use of CMP precess, it is difficult to accomplish the global planarization of in the defect-free inter-level dielectrics (ILD). we investigated the performance of $WO_3$ CMP used silica slurry, ceria slurry, tungsten slurry. In this paper, the effects of addition oxidizer on the $WO_3$ CMP characteristics were investigated to obtain the higher removal rate and lower non-uniformity.

Device miniaturization and high integrated circuit design is of major interest for the development of electronic devices. Various studies have been conducted to develop new material and processing technique[1]. Negative Differential Resistance(NDR) is the defining behavior in several electronic components, including the Esaki diode and most notably, resonant tunneling diodes(RTD)[2]. We made a comparison of electrical properties between 4,4-Di(ethynylphenyl)-2'-nitro-1-(thioacetyl)benzene and 4-[2,5-dimethoxy-4-(p henylethynyl)phenyl]ethynylphenylethanethioate, which have been well known as a conducting molecule having possible application to molecular level NDR devices. As a result, we measured current-voltage curves using Scanning Tunneling microscopy(STM), I-V curves also showed several current peaks between negative and positive bias region.

Zn electrode is being widely used as an anode material in alkaline battery systems. However the corrosion resistance of Zn electrode in KOH electrolyte is very low. So, to improve the corrosion resistance of Zn electrode $Pb_3O_4$ was mixed to Zn material. And 5 wt.% Pb3O4 addition was most appropriate quantity.

Diamond-like carbon (DLC) films were prepared with RF-PECVD (Plasma Enhanced Chemical Vapor Deposition) method on coming glass and silicon substrates using methane ($CH_4$) and hydrogen ($H_2$) gases. We examined the effects of $CH_4$ to $H_2$ ratios on tribological and optical properties of the DLC films. The structure and surface morphology of the films were examined using Raman spectroscopy and atomic force microscopy (AFM). The hardness of the DLC film was measured with nano-indentor. The optical properties of DLC thin film were investigated by UV/VIS spectrometer and ellipsometry. And also, solar cells were fabricated using DLC as antireflection coating before and after coating DLC on silicon substrate and compared the efficiency.

산소 과전압이 낮은 $MnO_2$를 촉매로 사용하여 반도체 산화물계의 산소선택성 전극을 제조하고 산화물 코팅층의 미세구조와 전기화학적 특성을 분석하였다. Ti 기판에 열분해 법을 이용하여 $MnO_2$ 피막을 형성하였고, 또한 binder를 이용한 코팅 방법을 이용하여 Ti, Fb 기판에 $MnO_2$ 피막층을 형성하였다. 450$^{\circ}C$에서 1시간 열분해하여 약 1 ${\mu}m$의 $MnO_2$ 피막층을 형성 시켰으나 Ti 기판과의 접착력이 약하여 피막자체에 대한 전기화학적 특성은 관찰할 수 없었다. PVDF : $MnO_2$의 함량비가 1:1에서 1:6 까지는 DMF의 함량에 무관하게 전극 특성이 나타나지 않았지만 20:1 이상의 조성에서는 균일한 C-V 특성을 나타냈고, 산소 발생 과전압도 약 1.4V 정도로 감소되었다. 그러나 Ti 기판의 경우 열분해법을 이용하여 제조된 전극과 같이 낮은 기판과의 접착력 때문에 $MnO_2$ 피막층의 촉매효과가 현저하게 감소하였다.

In order to anticipate gradual increase of fault current in electric power systems, current limiting technology and current limiting device has been investigated for a long time. But the commercial use of current limiting device was delayed due to the lack of effective method to insert impedance to the elective power systems without loss and surplus defects. However, novel current limiting device, which use superconducting materials, was considered as a dream technology to be applied in a distribution and transmission lines. LG Industrial systems and KERPI started to investigate resistive type superconducting fault current limiters in order to develop 154kV fault current limiters and this year, we succeed to test 3 phase 6.6kV/200A fault current limiters. Based on these achievements, 24kV superconducting fault current limiters will be realized withing 3 years which could be tested in a real fields. In this paper, the developments of fault current limiting module which use YBCO thin films, cryogenic systems, the structure and construction of 3 phase fault current limiters and finally the test results of 6.6kV superconducting fault current limiters will be introduced.

This paper deals with the detection method of the Quench phenomenon for superconducting magnet using the Acoustic Emission (AE) sensor. AE sensor is the elements, which is used to change the Acoustic signal to the voltage value. This signal may be used to detect whether the superconducting magnet has been at the Quench state or not. Recently, the development of the Quench detection technique, which is the using voltage and current signals, fiber-optic sensor, and so on, for the superconducting applications is widely studying. This method for the Quench detection of the superconducting magnet is also studying at some kinds of institute in Japan and the united state. Because of the large-scale superconducting magnet like International Thermonuclear Experimental Reactor(ITER) is charged a lot of energy, when the Quench phenomenon is being at the superconducting magnet it is happen to the problem of the protection for the applications. In this paper, we concluded that the Quench detection was possible when the mechanical stress by means of the local heat is generated at the part of inside superconducting magnets.

Effects of delay on the discharge time lag and the controllability of weak discharge mode were studied under single cell driving circumstances of ac PDP. It was found that sufficient number of priming particle is necessary for inducing weak discharge in ramp voltage driving. Discharge time lag was reduced dramatically under priming condition. It is speculated that the increasement of strong discharge is related to the reduction of the $Xe^*(^3P_1)$ particles during the after glow.

Misfiring is often observed during the high temperature quality assurancetest of plasma display panel. This limits the productivity of PDP industry. In this paper, experimental observations on the misfiring at high panel temperature have been performed through time dependent discharge light output and static margin measurement. For the high temperature condition, firing voltage increment is found in both surface and facing discharges. This in turn increases lime lag in address discharge, and results m increment of misfiring probability. In order to reduce this kind of misfiring, a new method that applies automatically different slope of ramp erasing pulse on the common electrode according to temperature variation is proposed. The experimental results show that controlling the slope of ramp erasing pulse is quite effective for compensating temperature-dependent variation of reset and address discharge.

In this paper, we studied on life-decision of underground cable of live-line state. Data of CV 6.6kV and 22kV cable's life is got data measured insulation resistance by D.C. overlapped current. We confirmed that D.C resistance reduced by time. Aging of cable could be occurred by electrical, thermal, mechanical stress and complex aging confirmed that proceeded by Weibull plot. In the result, life of 6.6kV cable remained 21 years till light caution and 35 years till heavy caution, so aging of 6.6kV XLPE cable was not occurred. Life of 22kV cable remained 10 years till light caution and 22 years till heavy caution. We confirmed that the designed life of 22kV cable is similar to the measured life.

This paper suggest the field test method of PD UHF sensor's sensitivity for a high voltage GIS and prove a reliability of the field test method through the test results of UHF sensor.

This paper describes the prediction of location of PD signals in GIS using the difference in the measured time between first and second wave arrival by the external-type PD sensors. It is well accepted that the electromagnetic wave in GIS propagates at the velocity of $3{\times}10^8$m/s. Consequently, we could identify the location of PD with high accuracy. The experience at the fields and the problems for the judgment are also discussed in detail.

가스절연 개폐장치(GIS)용 극초단파 부분 방전 측정장치에 다양하게 사용 할 수 있는 외장형 부분 방전 (PD) 센서를 제작하였다. Fat-dipole, 대수주기(log-periodic), spiral 및 log-spiral 형 패치안테나를 이용한 외장형 PD 센서의 주파수 특성과 검출감도를 기본 Dipole형 센서와 비교하였다. 제작된 센서는 170kV 단상 GIS의 스페이서에 장착하여 5 pC PD에 대한 각 센서의 주파수 특성과 감도를 측정 하였다.

Because the physics occurring during an interruption process is not well known, it is not easy to analyze the characteristics of a self-blast circuit breaker neither theoretically nor experimentally. Fortunately the available computational power and the numerical method improved recently make it possible to predict an interruption process as precisely and fast as possible. Therefore many researches using computational methods have been done for the interruption process of interrupters and applied to extend the information such as thermal and dielectric reignition. In this paper, we have simulated the interruption process of SF6 self-blast circuit breakers with the arc plasma during the fault interruption of a 10 kA current. The CFD program used here is coupled with the electromagnetic field analysis, the radiation model and the effects of turbulence. Through this work, we have get further information about the thermal performance as well as the behavior of the arc. The results have been compared with the measured arc voltage.

Taihan Electric Wire Co. developed accessories(PJ, EB-G, EB-A, EB-O) for 345kV XLPE $1C{\times}600mm^2$ cable as a small size conductor cable, after installed 345kV XLPE $1C{\times}600mm^2$ cable, PJ and EB-G on Youngseo${\sim}$Youngdeungpo project KEPCO planed in 2003. All of 345kV XLPE $1C{\times}600mm^2$ cable Accessories are finished the type tests successfully. Straight joint as a Prefabricated Joint(PJ) had shorter the days of assembling than those of TMJ used on the 154kV XLPE Cable. Particularly, the use of clean booth to prevent the dusts and the penetration of water also had made the quality of jointing improved.

Microwave heating system of KSTAR consists of ECH and LHCD. ECH and LHCD offer the reliability of operation in the beginning of plasma formation and non-inductive current drive for long time steady state operation with maintaining MHD stability, respectively. LHCD demands 5 GHz of frequency and consists of c-band waveguide, 4-port circuitor, dry dummy load, dual directional coupler, E-bend, arc detector. Our system is a lineup type pulse modulator that has 45 kV of output pulse voltage, 90 A of pulse current, 4 us of pulse width. 1:4 step-up pulse transformer, 7 stages of PFN and thyratron tube (E2V, CX1191D) are used in this modulator. The purpose of this paper is to show the modulator design and experimental result.

Flue gas from fossil fuel combustion is the main source of air pollution. It is recognized that $SO_2$ and $NO_x$, (sum of NO and $NO_2$) react with $H_2O$ and $O_2$ in atmosphere and convert precursors of acid rain. Streamer corona process using pulse power is one of the effective methods to remove these gases from stack. For this, pulse generator with 160 kV of output peak voltage, 0.3 ${\mu}s$ of pulse width and 120Hz of pulse repetition rate is developed. This paper shows the pulse compression characteristics to obtain optimum parameters for basic system design.

PD(Partial Discharge) signal emitted from PD sources has their intrinsic features in the region of time and frequency. STFT(Short Time Fourier Transform) shows time-frequency distribution at the same time. 2-Dimensional matrices(33${\times}$77) from STFT for PD pulse signals are a good feature vectors and can be decreased in dimension by wavelet 2D data compression technique. Decreased feature vectors(13${\times}$24) were used as inputs of Back-propagation ANN(Artificial Neural Network) for discrimination of Multi-PD sources(air discharge sources(3), surface discharge(1)). They are a good feature vectors for discriminating Multi-PD sources.

This paper deals with the lightning effects on aircraft. The effects are divided into two groups. The one is the direct effect due to the direct attachment of the lightning channel and/or conduction of lightning current. The other is the indirect effect like electrical transients induced by lightning in aircraft conductive components such as electric circuits. In this paper presents the analysis of lightning mechanism.

This paper deals with the lightning test methods on aircraft. It shows lightning current and voltage test waveforms referred to SAE ARP 5412. According to this standard, to test lightning effects, mixes appropriately 5 waves for current and 4 waves for voltage depend on structure and comparison information.

지금까지 변전소나 개폐소에서 전류, 전압을 계측하는 수단으로서 주로 철심과 권선으로 구성되어진 변류기(CT), 계기용 변압기(PT, PD)가 사용되어 왔다 최근, 2차측의 계측기나 보호 Relay의 Digital화가 진전되어, 또한 이것을 Digital Network으로 종합한 Intelligent 변전소의 구축이 검토되어짐에 따라 Digital Network에 대응한 신형 CT, VD가 요구되어 지고 있다. 상기와 같은 요구로 인해 당사에서는 CT는 검출부에 Rogowski Coil을 적용하며 그 후단에 적분기를 설치하였으면, VD는 검출부에 중간 전극을 이용해서 분압하는 방식인 Capacitive Voltage Divider를 사용하고 증폭기를 삽입하여, 각각 요구되는 전압 신호를 얻었다. 이러한 신형 CT/VD의 적용으로 종래의 CT/PT가 차지하는 공간이 필요 없게 되어 컴팩트한 GIS의 구조가 능하게 되어 있다.

기존의 단방향 차단기 소전류 차단성능 해석에서는 해석의 편의를 위해 실제 차단기의 고정부(고정아크접점과 피스톤)를 움직이게 하고 가동부(퍼퍼 실린더 노즐 등)를 고정시켜 놓고 해석을 하였다. 기존 차단기에서는 이런 식으로 해석을 하여도 아무런 문제가 발생하지 않았으나 이번 당사 모델인 550kV 50kA 1점절 차단기는 차단성능 향상을 위해 양방향으로 구동이 이루어지고 있어서 기존 방식으로 해석을 하는 것이 거의 불가능하다. 따라서 이번 연구에서는 상용프로그램인 PHOENICS를 이용하여 실제 차단기와 마찬가지로 가동부가 움직이도록 모의하는 방법을 개발하여 550kV 1점절 차단기의 소전류 차단성능을 평가하였으며, 앞으로 개발될 모든 복잡한 형태의 차단기도 쉽게 해석할 수 있는 계기를 마련하였다.

We have developed the external-type PD sensors for detecting of the electromagnetic waves up to ultra high frequency (UHF) bands, propagating in various type of GIS. Sufficiently high sensitivity and accuracy for practical use were achieved for the external PD sensor. The experience at the fields and the criteria for the judgment are also discussed in detail.

In seashore, outdoor insulators are polluted due to salty wind and the pollution causes the flashover and failure of electric equipments. As well known, the pollution has a close relation with meteorological factors such as wind velocity, precipitation, wind direction, relative humidity, dew point, etc. In this paper we statistically analyzed the correlation between the pollution and the meteorological factors including snowfall and freezing. The multiple regression analysis was used for the statistical analysis; daily measured equivalent salt deposit density(dependent variable) and the meteorological data(independent variable) were used. From the results of this investigation, we verified the influence of snowfall and freezing on the ESDD, which has been overlooked in the preceding investigation.

This simulated partial discharge caused by 22.9[kV] power cable using XLPE(Peroxide Crosslinkable Polyethylene) insulation having the outside damage. Asone of the insulation diagnostic method a radiated electromagnetic waves were measured by an UHF method using a BiconiLog antenna(EMCO-3142) and a spectrum analyzer used to measure EMl, EMC. From results of this study, It was confirmed that discharge progress were possible to be estimated by the proposed method.

This paper describes the discharge characteristics of liquid $SF_6$ (-41$[^{\circ}]$, 1.7[atm]) and $LN_2$ for plane to plane, needle to plane, plane to needle and sphere to plane electrode with gap variations from 1[mm] to 12[mm]. From this result, the breakdown voltage was increased with increasing gap length. Especially, the formation of bubbles by evaporation was observed in spite of non-applying voltage source. A corona is created of the applying voltage from the bubbles on the electrodes applied voltage. We consider it equal mechanism of corona as void exists in solid insulator. The results of liquid $SF_6$ and $LN_2$ discharge characteristics were caused by bubble formed evaporation and applied electric field voltage. Corona was happened to weak bubble and was proceed to new bubble breakdown.

본 논문에서는 2개의 유전체와 3개의 전극을 사용한 중첩방전형 오존발생기(Superposed Discharge Type Ozonizer, SDO)를 설계 제작한 후 중심전극 진공도 변화에 따른 고조파 오존발생기의 방전특성 및 오존생성특성을 연구하고, 방전 공간 내부에서 소비되는 에너지양을 측정하기 위하여 Lissajous법을 이용하였다.

현장에서 많이 사용되고 있는 GIS에 결함이 발생하면 치명적인 사고로 진전될 수가 있다. 본 논문은 모의 GIS내 도전성 금속이물질 존재 시 발생되는 부분방전 신호를 절연진단 방법중 하나인 UHF법을 이용하여 부분방전 시 방사되는 방사전자파의 스펙트럼을 분석해서 방사전자파의 거리에 따른 감쇄율을 측정하였다. 이러한 연구는 현장 GIS 및 $SF_6$ 가스절연 전력설비에서 금속이물질에 의해 발생되는 방사전자파 측정에 중요한 역할을 할 것으로 사료된다.

From the plasma application point of view, electron temperature and density are one of the most important parameters for plasma process. But it is only available to control plasma by adjusting external factors like gas pressure and input power. In this paper, pulse-modulated plasma is generated by modulating 13.56GHz RF power with 1, 5, 10kHz pulse. And Langmuir probe technique is used to study the distribution of electron temperature and density. When modulated pulse is off, electron temperature decreases gradually in form of exponential decay. The value t of exponential decay slope is 33.619, 13.834, 10.803 in 1kHz. 5kHz. 10kHz. This implies that this method can be used to control electron temperature and density.

In this study, major research fields are classified as ozone generation system for dry cleaning wafer of etched silicon wafer, dry cleaning process of etched silicon wafer which includes SEM analysis and ESCA analysis. The following results are deduced from each experiment and analysis. The magnitudes of carbon and silicon were similar to the survey spectrum of silicon wafer which does not cleaning, but magnitude of oxygen was much bigger Because UV light activates oxygen molecules in the oxide film on the silicon wafer.

Spherically convergent beam fusion device accelerate ions, which are generated between outer anode and inner grid cathode, toward the spherical center. The collision of opposite direction ions give rise to fusion reactions. Spherically convergent beam fusion device is very simple and compact, therefore the device has a potential that is applied to a portable neutron source. An experimental device consist of a 20cm-diameter spherical mesh-type anode and 7cm-diameter open spherical grid cathode and was maintained at a constant pressure of about 1333 Pa by feeding argon gas.

최근 XLPE 케이블의 신뢰성 향상을 위한 지속적인 연구 및 기술개발이 성과를 나타내면서, 지난 한세기동안 세계적으로 실선로에 적용되어 그 신뢰성을 인정받던 OF 케이블이 XLPE 케이블의 상대적으로 낮은 송전 손실, 높은 방염 특성 및 유지보수와 설치의 편이성에 밀려 그 수요가 급격히 감소하고 있는 추세이다. 이러한 추세에 따라 기존의 OF 케이블 선로의 증설 또는 이설 공사의 경우, 기설 OF 케이블 선로에 XLPE 케이블을 연결하여 사용하는 경향이 많아지며, 이 이종의 케이블을 상호간 연결하는 중간접속함의 필요성이 대두되었다. 이 이종케이블 접속함은 각 케이블의 제반 특성을 최대한 유지하는 동시에 장기적인 신뢰성 확보가 최대 과제이며, 기설의 전력구에 사용하기 위한 경량화 또한 요구된다.

This paper described the capacitive sensor for the diagnosis of deterioration of electrical insulating oils applying guard-ring type the 3-terminal electrodes. To measure stable capacitance of the sensor and to determine the design factors of the sensor, we utilized computational analysis, FEM software. This capacitive sensor discern the extent of deterioration measuring relative permittivity of electrical insulating oils. The result of measuring numerous sample, mineral oils, as serviced year, we confirmed an increase in relative permittivity of oils. Moreover, we confirmed the superior characteristics of the sensor as a species, aged pattern of oils and operating temperature.

The degree of contamination on outdoor insulator is one of the most importance factors to determine the pollution level of outdoor insulations, and the sea salt is known as the most dangerous pollutant. As shown through the preceding study, the generation of salt pollutant and the pollution degree of outdoor insulator have a close relation with meteorological conditions, such as wind velocity, rainfall, and so on. So, in this paper, we have made database using the past meteorological data and ESDD(equivalent salt deposit density) and then we predicted the pollution degree in the future after analyzing currently meteorological data of database.

The UHF electromagnetic waves excited by PD pulses propagate along the GIS busbar not only TEM mode, but also TE and TM mode. Generally the waves detected by the UHF sensors are those of high order modes and such waves can only propagate the higher than cut-off frequency. In this paper, computed cut-off frequency of 362[kV] GIS by each modes and simulated electromagnetic field of each propagation modes by FEM(Finite Element Method) program. Frequency band of each TEmn/TMmn modes were determinated by simulation results and were discussed optimal position of UHF sensor from this results.

This test was performed to assess the correlation between insulation diagnostic tests and breakdown voltage strength of the stator winding of 6.6kV class induction motor in insulation deterioration condition which have been in service for 5 years after being installed in 1998. The insulation diagnostic tests include resistance, polarization index(P.I), dissipation factor(${\triangle}tan{\delta}$), maximum partial discharges(Qmax) and AC breakdown test. we evaluated the correlation between insulation diagnostic test and AC breakdown test for stator winding of high voltage induction motor.

In oil-filled equipment such as transformers, partial discharge or local overheating will make insulating material(oil, kraft paper, proclain and wood) be stressed and generate many sort of gases(CO, $CO_2,\;H_2,\;C_2H_4$) which are dissolved in transformer oil. The ratio of this gas can make diagnostic tecchniques of the lifetime of transfomer so, it is important to monitoring $H_2$ gas continuously. This paper developes a system of detecting about $H_2$ gas by using $H_2$ gas sensor, and we describe operation and performance of this system.

In oil-filled equipment such as transformers, partial discharge or local overheating will precede a final shutdown. Accompanied with such problems is a decomposition of insulating material into gases, which are dissolved into the transformer oil. The gases dissolved in oil can be separated with some membranes based on the differences in permeability of membranes to different gases. This paper discuss the permeability characteristics of several membranes for separation hydrogen gas in oil. With result of this paper, it may become possible to detect fault-related gases from transformer oil and predict incipient failures in the future.

변압기에 사용되는 절연유의 열화정도를 변압기의 운전정지 없이 실시간으로 측정할 수 있는 전기용량을 이용한 센서를 개발하였다. 개발된 전기용량형 센서는 3-전극형의 구조와 변압기에 센서의 외부상자가 접지 될 때 2중의 정전차폐가 되도록 하여 외부로부터의 잡음에 영향을 받지 않도록 하였다. 또한 변압기에서 절연유의 온도변화에 따른 유전율 변화를 보상하기위하여 기준용 센서와 측정용 센서를 한개의 변압기에 장착함으로 온도보상이 되도록 하였다. 제작된 센서는 변압기에서 절연유의 사용기간에 따른 유전율의 변화를 정확히 측정하였으며, 절연유의 체적저항의 변화도 감지 할 수가 있다. 따라서 센서에서 출력되는 신호를 phase sensitive detector를 사용하여 유전율의 변화로 혹은 체적저항의 변화로도 나타내 보일 수가 있다.

The important consideration in laboratory designing and construction of the artificial pollution testing facilities including 300kV, 1800kVA AC test system, which enable to test and evaluate the UHV dielectric performance of power insulators up to transmission class, has been dealt in this paper. To evaluate the performance characteristics against contamination for various power installation, especially for the insulators and kinds of bushings, brief investigation and an analysis of test objects and related international codes and standards have been conducted. With the special consideration concerning other matters in designing of these testing facilities have been described with the fixed ratings and references.

In this paper, there have been brief review about the important consideration in laboratory planning and designing 4.2MV impulse voltage generator(IVG), which enable to test and evaluate the UHV dielectric performance of power electric apparatus up to 765kV-class. To improve and reinforce the test ability of the IVG and itself against test object being tested by KERI hereafter, wide investigation and an analysis for a solution, especially overshoot compensation method. With the special consideration about those matters in settling down the 4.2MV IVG have been described with the experimental approaching.

It is widely known that the ultra high frequency (UHF) method that detects the electromagnetic wave of the PD pulses in the gas insulated space is one of the most competitive methods for its high sensitivity. From the above point of view, this paper describes the noise suppression methods and the PD measurement results of the in-service substation by the developed UHF PD measurement system which consists of the external UHF coupler, the UWB LNA and the digital storage oscilloscope. As results, it was found that the effect of the noise suppression methods were verified and that the developed external UHF coupler showed a better detection sensitivity than a conventional external coupler.

It is widely known that the ultra high frequency (UHF) method that detects the electromagnetic wave of the PD pulses in the gas insulated space is one of the most competitive methods for its high sensitivity. From the above point of view, this paper describes the characteristics of GIS PD signals measured with ultra wide band (UWB) GIS PD detecting system in which PD signals are detected into the dual UHF band. The UWB PD detection system consists of the UWB UHF coupler, the UWB low noise amplifier (LNA) and the oscilloscope. The dual bands for PD signals are 0.5-2GHz(full band) and 1-2GHz(high band). As results, it was found that the partial discharges of each defect have their own characteristic pattern and the ratio of High band to Full band increases with gas pressure.

As rise the demands for the protcetion of environment and the compactness of equipments, the movement brisks for replacing the circuit breaker of GIS(Gas Insulated Switchgear) to VI(Vacuum Interrupter). For these reason an increase in the interruption capability of VI is required. To satisfy these requirement, the academic and industrial worlds have been studying extensively for AMF(Axial Magnetic Field) contact, which is effective in interrupting large current over tens of kA, and introduced many kind of AMF contacts. However there are little effort to compare these contacts comprehensively, so it is difficult to choose most suitable shape for user's needs. In this paper, focusing unipolar type contact among various type of AMF contacts, we performed magnetic field analysis for several models designed in same dimension and compared the result and characteristics of each model in order to help deciding the direction for developing profitable VIs for interrupting large current.

This paper deals with the device for measuring the time-varying magnetic fields and induced voltages caused by lightning discharges. The system consists of two loop antennas for the measuring the magnetic flux density and induced voltages caused by the lightning current, an integrator a data acquisition and a personal computer with a software package that was developed for the analysis of the measurements.

The primary role of ZnO arresters is to protect transmission and distribution equipments against lightning surges. The extremely nonlinear V-I characteristics of the ZnO arrester obviates the need for isolation gaps and consequently it is continuously connected to line voltage. For this reason, ZnO arresters are degraded with increasing with time in actual power systems. In this work, the characteristics of the luminous events between the ZnO block and electrodes were investigated. As a result, the luminous events were effected by the impulse and the near polarity of the luminous event was intense near the grounded electrode. Also the luminous event may cause the degradation of ZnO arrester block.

보이드, 이물, 돌기등 고부자 절연체 내의 결함은 이곳에 전계가 가해질 때, 국부적 전계집중을 유발하며, 절연체 내의 미소 방전을 일으킨다. 이 때 발생한 미소 방전에 의해 보이드 표면의 고분자 물질은 기계적, 화학적 열화를 일으키며, 이에 따라 전기적 트리를 형성하게 된다. 이러한 트리는 결국 절연체의 절연파괴로 진전되므로, 고분자 물질을 절연물로 사용하는 전력기기의 경우에는 신뢰성에 큰 문제를 유발한다. 따라서, 이러한 방전(부분방전)이 일어날 때 생기는 전기적 신호를 검출하여, 절연물의 신회성을 평가하는 것은 매우 중요하다. 본 논문에서는 이러한 미소방전이 일으키는 방전의 파형이 트리의 진전에 따라 어떻게 변화하는지에 대해 연구하였다.

A high rate deposition sputtering process of magnesium oxide thin film in oxide mode has been developed using a 20 kW unipolar pulsed power supply. The powersupply was operated at a maximum constant voltage of 500 V and a constant current of 40 A. The pulse repetition rate and the duty were changed in the ranges of 10 ${\sim}$ 50 kHz and 10 ${\sim}$ 60 %, respectively. The deposition rate increased with increasing incident power to the target. Maximum incident power to the magnesium target was obtained by the control of frequency, duty and current. The deposition rate of a moving state was 9 nm m/min at the average power of 1.5 kW. This technique is proposed to apply high through-put sputtering system for plasma display panel.

A systematic approach of measurement, modeling and analysis of grounding system impedance is presented. The measurement and analysis system of ground impedance is based on a computer aided technique. The ground impedances of the ground rod are considerably dependent on the frequency. The ground impedance is mainly resistive in the frequency range of 3-20 kHz. At higher frequencies, the reactive components of the ground impedances are no longer negligible and the inductance of the ground rod was found to be the core factor deciding the ground impedance. As a consequence, the equivalent circuit model based on the measured data was proposed, and the calculated results were in approximately agreement with the measured data.

변압기의 고체절연이 열화 되거나 불순물 및 수분이 혼입되어 그러한 결함부분에 임계치 이상의 고전계가 인가되면 부분방전이 발생한다. 현재 변압기에서 부분방전을 검출하기 위하여 부싱탭을 이용하거나 전류센서, 초음파센서 등을 이용하여 부분방전을 검출하고 있지만 전기적인 부싱탭이나 전류센서를 이용한 검출방법은 주변 잡음의 영향을 많이 받고 초음파법은 감도가 낮다는 단점을 가지고 있다. 본 연구에서는 이와 같은 단점을 보완할 수 있는 방안으로서 전자파를 이용한 부분방전 측정에 대한 기초연구를 실시하였으며, 변압기운전중에 전자파측정에 의한 부분방전감시가 가능한 것으로 나타났다.

In this paper, the waveform parameters of electromagnetic pulses radiated from intracloud discharges were presented. The zero-crossing times and the full pulse widths of the large bipolar electromagnetic pulses due to intracloud discharges are gradually decreased as the stroke proceeds. Also, the electromagnetic pulses tend to be bipolar, with narrow and fast leader pulses superimposed on the initial half cycle. The mean numbers of leader pulses superimposed on the initial half cycle were 1.61${\pm}$0.74 and 1.75${\pm}$0.73 for the positive and negative polarities, respectively.

This paper presents the aspect and distribution of voltage and current harmonics being made at low voltage power systems. The voltage and current harmonics in power systems supplying various loads were monitored and analyzed. We have examined the results compared to advanced countries' harmonics control standards. As a result, the current harmonics were significantly greater than the voltage harmonics. In particular, the harmonics of currents flowing through loads with power switching electronics was pronounced. Also, the contents of current harmonics of street lamp circuits was about 30%, and it was decreased to 12.3% with the installation of scries reactor. On the whole, The measured results of voltage and current harmonics exceeds the regulation limits recommended by IEEE std 519-1992.

현대사회에 들어서면서, 전력수요의 중가와 전력기기산업의 고집적화에 따라 사고시에 발생하는 파급효과가 대형화되는 추세에 있다. 따라서 이를 미연에 방지하기 위한 연구가 각 분야에 걸쳐 활발하게 진행되고 있다. 이에 당사에서는 초고압 계통에서 사용되는 SF6가스 절연 GIS(Gas Insulated Switchgear) 및 Oil-Transformer에서의 부분방전 측정/분석을 위하여 UHF/AE를 이용한 on-line/portable 측정 시스템을 개발하였다. 본 논문에서는 개발/상용화 되어 field에서 사용되고 있는 시스템의 전반에 대하여 설명한다. 또한 철재 선진사와 공동 진행중인 Risk Assessment에 대하여 언급하였다.

이 논무에서는 유입식 변압를 대상으로 UHF 대역의 펄스신호를 검출하는 센서를 소개하고, 이를 이용한 방전 결함별 측정 결과를 소개한다. 측정결과는 기존의 PRPD법과 주파수 Domain과 위상 Domain에 대한 정보를 가지는 p-f-q 분석으로 측정 하였으며, 본 논문에서는 후자의 결과를 중심으로 서술 하였다.

전력을 공급하는 변전소 등의 주요 위치에 시설되는 GIS는 사고를 미연에 방지하기 위해 여러 가지 진단방법을 이용하여 이상여부를 판별한다. 이러한 진단 방법 중 현재 국내외적으로 각광을 받고 있는 방법이 UHF센서를 이용한 부분방전 검출방법이다. 따라서, 본 논문에서는 부분방전을 발생시키기 위한 인공결함을 제작하여 GIS 내부에 삽입하고 부분 방전을 발생시켰으며, 이때 발생된 부분방전 신호를 UHF센서를 이용하여 검출하였다. 검출된 부분방전 신호는 phi-f-q 방법으로 분석 하였으며, 그 결과 발생된 파라메터를 인공신경망에 적용하여 각각의 결함에 따른 인식률에 대하여 알아보았다.

In this paper, in order to analyze the characteristics of degradation by salt water with insulation cover and OC wire(outdoor cross-linked polyethylene insulated wire) used in power receiving system, an experimental apparatus has been designed and fabricated. An insulation cover and OC wire were installed in an experimental apparatus, and degraded in each case of 2%, 5%, 10% salinity during 12 weeks. An optical microscope was used to observe a changing process of sample surface, and an electrical safety was analyzed by measuring dielectric breakdown voltages of samples. As salinity increased, so ununiformity of sample surface increased. The breakdown wasn't produced to 50kV about samples regardless of salinity, testing period.

The degradation systems of non degradable waste water consist of the arc plasma torch, power supply, a feeder of liquid waste and reactors. Output of stable plasma torch, suitable air flux, microscopic atomizing state of waste water and long reaction section must be to degrade waste water more efficiently. In this paper, we are designed the stable power system, the microscopic atomizing state of waste water and the efficient reactors to satisfy various conditions. Non degradable wast water used in this work was $Na_2$EDTA of 1.0 mol. The concentration of $CO_2$ and EDTA was analyzed using GC (Gas Chromatography) and HPLC (High Performance Liquid Chromatography). In the result show that $CO_2$ concentration was about 96% and EDTA was degraded approximately 96%.

고압전동기나 발전기의 사용수명은 절연시스템의 열화에 의해 좌우된다. 일반적으로 기기의 내구성을 확인하기 위해 국제규격이나 국내규격에서 적용하고 있는 방법으로는 온도에 의한 열화시험을 실시하여 절연계급에 대한 내구성을 평가한다. 본 논문에서는 현재 국내에서 제정된 신뢰성평가기준에 따른 국내 2개 회사의 일반유도전동기에 대해 실시한 온도 가속수명시험을 통해서 얻어진 자료를 이용한 시험방법의 개선 및 고장분석 등 신뢰성분석에 대해서 서술한다.

본 논문은 옥외용 고분자 절연물로 널리 사용되고 있는 실리콘 고무의 장기 자외선 가속열화에 따른 특성변화를 조사하였다. 이를 위해 전기적인 평가 방법 이외에 각종 화학적 분석기기를 사용하여 보다 정확히 재료의 열화를 판정하고자 하였다. 연구결과, 실리콘 고무는 내후성이 우수하지만, 가속열화가 진행되면서 표면의 전기적 저항률이 높아지고, 전하축적이 용이해지는 표면구조로 변하는 것을 확인하였다. 또한, 재료 내에서 발수성 회복역할을 하는 저분자량 성분이 감소하였고, 열적특성이 변화되는 것을 확인하였다. 이를 통하여, 최근 확산되고 있는 옥외용 고분자 절연물의 성능평가 및 수명예측에 도움이 되고자 하였다.

It is caused that insulation paper, which had got a lot of thermal stress by over-load after installation, should have been deteriorated in electrical and mechanical characteristics. Beside, insulation material is decreased the insulating property and accelerated aging of them in case of dielectric loss when transformers are manufactured with some moisture or transformers would have been them because of moisture-permeation, Therefore, in this study we experienced the influence of moisture content in case of the thermal aged insulation paper. we have measured tan ${\delta}$ and breakdown voltage in the ratio of paper' moisture content before the aging and then taken the same tests again after insulation paper thermally accelerating-aged. There is a purpose to gain data for a life-design and to establish aging mechanism in order to continuously study life expectancy of the insulation paper.

As the characteristics of LED disposition, LED warning light must be designed differently from general incandescent lamp warning light whose light source is located in origin. In this paper, the globe's lens of LED warning light was designed considering the LED intensity distribution and the arrangement of the LED. And prove the appropriateness of that design by simulation in LightTools which is optical design program.

Inductively coupled plasma is commonly used for electrodeless lamp due to its ease of plasma generation. Optical characteristics significantly depend on the RF power and gas pressure of the plasma. This paper describes the measurement of luminance as a function of RF power and gas pressure with a goal of finding optimal operating conditions of the electrodeless lamp. The gas pressure was varied from 10 [mTorr] to 500 [mTorr] and the RF power was varied from 10 [W] to 200 [W]. It was found that the luminance tends to be decreased when argon pressure is increased, and the luminance is increased as RF power is increased. It was also found that the luminance per unit RF power is high when the argon pressure is low and when the RF power is in the range of 30 [W]${\sim}$40 [W].

본 고에서는 해남-제주간에 사용되는 Phase Control Thyristor의 구입비용을 고려하여, 해남-제주간 PCT와 동일 구조를 갖지만 전압/전류용량이 작은 A, B사의 PCT를 각각 40개씩 확보하였다. PCT의 가속열화를 위한 스트레스 인자는 전압/열이며, 이를 동시에 인가할 수 있도록 가속열화 시험장치를 구성하였다. 또한 가속열화에 의해 열화정도를 파악하기 위해 초기 특성을 측정하였으며, 이에 대한 결과를 기술하였다.

V-p characteristics and the discharge luminous characteristics in inhomogeneous $SF_6$ gas gap under the positive and negative lightning impulse voltages are presented. The test gap was composed of the plane-to-plane with a needle-shaped protrusion. The applied voltage and the predischarge current were measured by the electric field sensor and the shunt of 50 ${\Omega}$, respectively. The light emission signals were observed by a photomultiplier tube, and a high-speed camera. In a consequence, the dielectric strengths of $SF_6$ gas gap under positive lightning impulse voltages were independent of the gas pressure. In the presence of the positive polarity, the branches of discharge channel were created and the directions of the discharge paths were random. On the other hands, the discharge paths of the negative polarity were more thicker and brighter.

여러 그룹의 연구 결과로서 고밀도 유도결합 플라즈마원 유체 수송 시뮬레이션을 위해 다양한 경계 조건을 포함한 여러 가지 모델이 제시되어 왔다. 본 연구에서는 가능한 모델들과 경계 조건을 설정하여 FDM(finite difference method), up wind scheme, power-law scheme, die1ectric relaxation scheme[1]을 기반으로한 1차원 시뮬레이션을 통해 정확성과 수치 해석적 안정성 및 효율성 연에서 비교, 검토하였다.

현재 널리 쓰이는 고밀도 플라즈마 장치의 식각 시뮬레이션은 식각 패턴으로는 level set method이며 바이어스가 인가된 sheath model로는 Riley sheath model 이 보편적으로 받아들여지고 있다. 이러한 식각 시뮬레이션은 RF(Radio Frequency) sheath로부터 가속된 이온이 단위 입체각당 특정 지점에 이온 플럭스 분포함수, 이온 에너지 분포함수와, 중성종의 수송모델로 etch rate을 결정하는 과정과 level set method을 이용하여 식각 형태를 계산하는 과정으로 구성되어있다. 본 연구는 식각 형태 계산 이전의 단계로서 $Ar^+,\;Cl_2{^+},\;Cl^+$이온의 유동속도와 밀도를 장치의 radial방향으로 불균일하게 가정하였고, 가정한 값으로 이온 플럭스와 에너지 플럭스에 대한 영향을 알아보았다.

SOM(Self Organizing Map) algorithm which has some advantages such as data accumulation ability and the degradation trend trace ability was compared with conventionally used BP(Back Propagation) algorithm. For the purpose, partial discharge data were acquired and analysed from the artificial defects in GIS. As a result, basically the pattern recognition rate of BP algorithm was found out to be better than that of SOM algorithm. However, SOM algorithm showed a great on-site-applicability such as ability of suggesting new-pattern-possibility. Therefore, through increasing pattern recognition rate it is possible to apply SOM algorithm to partial discharge analysis. Also, for the image processing method it is required the normalization of the PRPDA graph. However, due to the normalization both BP and SOM algorithm have shown worse results, so that it is required further study to solve the problem.

본 연구에서는 변압기형 플라즈마 전류 모델을 기초로 한 평판형 유도 결합 플라즈마 장치에 대한 회로를 분석하여 임피던스 매칭 특성을 조사하였다. 장치 임피던스는 collisional surface impedance를 기반으로 계산된 플라즈마 임피던스와 안테나 임피던스로 결정된다. 매칭 network에 사용된 회로는 Altcmatc-typc의 회로이고, 매칭 소자인 $C_T$와 $C_L$은 임피던스 매칭 조건을 이용하여 계산하였다. 완전 매칭의 경우에는 $C_T$와 $C_L$을 플라즈마 변수들의 함수로 표현하여 의존성을 분석하고, 불완전 매칭의 경우에는 반사파에 대한 반사계수, 반사율을 계산하였다.

In this paper, we discussed measurement method of PD (Partial Discharge) of 22.9[kV] cable. Cable rail track laying portable detector that can detect partial discharge of cable connection ashes by on-line done spot way to detect Lemke equipment and high broadcasting CT sensor that use antenna sensor using ICM mounting was explained. Because measurement corona signal is very big, analysis of partial discharge is difficult state, we used connector. It could be attenuated by 2 times. We found out that corona signal which generated on B phase is flowed on A phase and C phase. It could measure that partial discharge of A phase happens actually. We could confirm that partial discharge of about 250 ${\sim}$ 300 [pC] on A phase is dangerous.

밀도는 플라즈마의 기본적인 물리적 성질을 이해하는데 중요한 인자로 인식되고 있으며 많은 방법들이 밀도분포의 측정에 이용되었다. 이 중 마이크로파 진단법의 하나인 레플렉토메터리는 그 고유한 특성 때문에 현재 밀도분포측정법으로써 폭넓게 활용되고 있다. 그러나 레플렉토메터리 신호에 대한 처리 및 분석 방법은 다양하여 주어진 플라즈마에 가장 절적한 방법을 선택하는 것은 쉽지 않다. 본 논문에서는 레플렉토메터리의 신호로부터 밀도분포를 정확히 재구성하는 알고리즘을 개발하기 위한 기초 단계로써 모의된 레플렉토메터리 선호에 기존의 신호해석법들 중 우수한 해석법으로 알려진 CDM(complex demodulation method)과 웨이브레트(wavelet) 분석법을 적용하여 밀도분포재구성에 대한 양자의 성능을 비교한다. 그리고 플라즈마의 특성에 기초하여 모의된 신호에 실제 상황에서 존재할 수 있는 잡음신호를 첨가하여 이것이 밀도분포 재구성에 미치는 효과를 조사한다.

In this paper, we studied on the potential characteristics of human-body contacted the charging part. A charging part of electrical facilities and the earth are simulated by the e1ectrode pole and conductive rubber plates respectively. As the results of these follows, when the potential distribution of the human-body contacted the charging part is far from the electrode pole, a lot of currents flow through the human-body. Besides human-body non-contacted the charging part is affected by step voltage. Therefore, we could find out the causes of the electric shock accidents and be expected to the data for minimization of human error occurred the workspace.

"CRT" which had dominated the market of display until 2000 is not appropriate for information indicating media due to several limitations. Thus, TFT-LCD, PDP, OLED, etc are growing in display industry instead of CRT because they meet demands of information indicating media. OLED display which responses within 1ms fits any picture manifestation medias because it uses self radiance OLED for picture clement that has no obstacles in showing the angle of vision. OLED's characteristic of action is very sensitive to thickness of electrode so that this has been an important issue. This study tried to find the most suitable thickness of electrode using ITO, Mo, and AL. Using the results of IVL measurements, analyzed equality of electrode board. As a result, found the thickness of electrode that has high electrical efficiency and optimized it.

가속기 연구소에서 개발한 고전압 대전류용 Seal-off TVS (Triggered Vacuum Switch)의 특성을 시험 하는 것을 목적으로 하고 있다. 제작한 TVS는 양전극과 음전극이 교대로 고정된 간격으로 각각 3개의 전극으로 배열되어 있으며 전극은 사다리꼴 모양으로 되어있고 트리거 시스템과 개스를 흡수하는 게터가 내부에 설치되어 있다. 제작한 스위치 내부는 약 $10^{-7}$ torr의 진공상태를 유지하고 있으며 세라믹 챔버를 사용하여 Seal-off 상태로 설계, 제작하였다. 스위치 시험장치는 200 ${\mu}F$, 22 kV 6개를 병렬로 연결한 커패시터 뱅크와 $20{\mu}H{\sim}160{\mu}H$의 탭변환 인덕터와 $0.1{\Omega}{\sim}0.5{\Omega}$ 의 저항을 이용하여 시험 장치를 구성하였다. TVS의 시험에서 에너지 최고 전달량은 74 C 이었으며 이때 인가전압은 30 kV, 최대 전류는 100 kA, 펄스폭은 1${\sim}$2 ms이었다. 본 논문은 제작한 스위치의 전기적인 특성 시험한 결과에 대하여 논하고자 한다.

In this study, we propose a small high voltage power supply which use a half-bridge ZCS resonant and Cockroft-Walton on circuit, for ESP (Electrostatic Precipitator). This power supply transfers energy from ZCS resonant inverter to step-up transformer and the transformer secondary is applied to the Cockroft-Walton circuit for generating high voltage as discharging source of electrodes. It is highly efficient because its amount of switching losses are reduced by virtue of the current resonant half-bridge inverter, and also due to the small size, low parasitic capacitance in the transformer stage owing to the low number of winding turns of the step up transformer secondary combined with the Cockroft-Walton circuit. From these results, the best operational condition is obtained at the switching frequency of 9 kHz and the duty ratio of 50 % in this ESP.

Nowadays, $CO_2$ lasers are used widely in many applications such as materials fabrication, communications, remote sensing and military purpose etc. Especially, $CO_2$ lasers are in the spotlight at surface handling and heat processing. It is important to control the laser output power and beam Quality in those fields. And those are studied the important parameters deciding the fluctuation of laser beam are smoothing capacitor, frequency and the characteristics of laser resonator. But the study of plasma parameters of $CO_2$ lasers are little. So we detect the $CO_2$ laser from emitted $CO_2$ laser discharge plasma using a non-contact photo tansistor sensor and Low pass filter. In this study, The relativity of the emitted light of discharge plasma and CO2 laser output.

In this paper, maxwell 3D finite element analysis program was used to obtain electromagnetic properties associated with the coil and nearby structures. The electromagnetic emitting properties were presented by 3D simulation software operated at 2.56[MHz] and some specific conditions.

In this paper, we have studied shielding characteristics of high conductivity or high permeability materials on ELF magnetic fields generated from single or three phase AC line. Perm alloy has been selected as high permeability material and copper as high conductivity material. Four-plate shield (square section) was considered as a shielding shape. We found copper showed stable shielding effects more than perm alloy.

An ultra wide band ultra-high frequency (UHF) signal processing module was designed for on-line UHF partial discharge (PD) monitoring systems for gas-insulated switchgears (GIS). Major advantage of the unit is an improved PD detection sensitivity through minimizing the effect of surrounding interference signals. The detection sensitivity of the unit was <-60 dBm that is sufficient to detect UHF PD signals as low as 1 pC. Precise detection of PD occurred in the GIS, due to internal defects, is possible by using the signal processing unit.

최근 F. F. Chen 에 의하면 [F.F. Chen and D. Arnush, Phys. Plasmas, 8, 5051(2001)], 원통형 량뮤어 탐침의 경우 플라즈마 전위와 부유 전위의 차(${\triangle}V_{pf}$) 가 상수가 아니며 플라즈마 밀도에 따라 달라지고 밀도가 아주 높은 경우 즉 쉬스가 탐침의 반경보다 아주 얇은 경우에는 ${\triangle}V_{pf}$ 는 평면 탐침과 같이 상수가 된다는 것을 이론적으로 보였다. 이에 본 연구에서는 아르곤 유도 결합 플라즈마에서 원통형 량뮤어 탐침을 사용하여 F. F. Chen의 이론적인 결과를 실험으로 검증하였으며 F.F. Chen 의 이론적인 결과와 잘 일치하였다.

For evaluation of partial discharge performances of electrical power appratus such as Insulator, circuit breaker and transformer and so on, Partial discharge measuring system(ERA) consisted of PD detector including amplifier, coupling capacitor, PD calibrator and voltage divider are used PD measuring system is very important factor which affect the test result and show reliability of test result in test laboratory, In this paper, we describe tracebility and uncertainty of PD measuring system in test laboratory based on IEC 60270.

본 논문에서는 디지털 오실로스코프와 이더넷(TCPIP)을 기반으로 한 극초단파 부분방전 신호취득 체계를 개발하였다. 원격으로 오실로스코프를 제어하고 측정한 부분방전 신호를 취득, 전송, 저장, 분석 할수 있는 체계를 개발하였다. 기간 구성품으로 최근 발전된 윈도우즈 기반 디지털 오실로스코프와 Labview를 사용하여 가스절연개폐장치(GIS) 내부에서 발생하는 극초단파 부분방전 신호를 측정하고 저장하여 실시간으로 위상분해 분석방법을 적용하여 측정된 신호를 표시하였다.

We developed internal and external type sensor to measure ultra-high frequency (UHF) partial discharge (PD) in 170 kV gas-insulated switchgears (GIS). We also manufactured a PD-generator to verify and measure the detection sensitivity of those sensors. We measured the output power of the UHF PD sensors induced by PDs of 5 pC using the PD-generator. We measured UHF propagation loss of an 170 kV GIS for optimal arrangement of the sensors. We used swept UHF signal from a network analyzer into the GIS to measure the loss of various components of the GIS.

대전력 펄스 파워를 발생시키기 위한 마이크로파 발진기는 수GW의 대출력이 발생되고 있는데 발진특성, 높은 주파수, 발진출력향상등에 대한 여러 가지 연구가 진행되고 있다, 마이크로파는 지파회로를 이용하면 광속보다도 낮은 주파수를 갖게되며 전자빔과 속도가 일치될 때 에너지의 증대가 일어나 대전력 펄스퐈워를 발생시킬수 있다. 본 연구에서는 회로파의 군속도가 부의 영역에서 동작하는 후진파 발진기를 이론적인 계산에 의하여 연구하였다. 연구는 수십GHz의 주파수를 이용하여 보다 높은 출력, 효율이 발생되도록 하였고 분산특성을 이용하였다.

Stator coil of rotating machinery has shown different characteristics according to impregnated with coil or not. And this is major determinant of equipment's life. In this paper, PD characteristics is studied as a classification scheme between two specimens. Processing of the coil impregnation is very important thing because that influences on thermal and electrical characteristics of the coil. And then PD is occurring at the coil and causing insulation degradation. For processing statistical processing, PD data acquired from PD detector using PDASDA(partial discharge acquisition, storage and display system). And also these statistical distribution and parameter are applied to classify PD sources by neural networks. As a result of, Neural Networks have a good discrimination rate for classification PD sources.

Investigation of surface discharge characteristics of surface leakage on polluted EPDM insulatora have been performed This work was performed utilizing high frequency CT's to monitor surface discharge. It was found that there were significant variation in the surface discharge waveform frequency spectrum, depending both on the surface discharge magnitude and more importantly on the duration of surface discharge activity.

In this paper, we investigated electrical property of epoxy resin which includes elastomers to improve electrical and mechanical property, as varied to additive elastomer contents. There are four samples with 5[phr], 10[phr], 15[phr] and 20[phr]. We meIt was experimented with changing temperature($-80^{\circ}C{\sim}50^{\circ}C$) and frequency (10Hz, 60Hz, 1kHz, 10kHz) According to the experimental results, when the additive elastomer contents are increasing, the permittivity and tan${\delta}$ has very high value in particular at low frequency and high temperature. It also appears that those increasing rates relate to additive elastomer contents. That is to say, even though epoxy resin are improved in mechanical property according to elastomer contents, the elastic epoxy can has bad dielectric characteristics for electrical power application.

가스절연개폐장치에서 발생하는 사고를 예방하기 위해서는 방전 위치 및 방전원인을 방전신호로부터 유추하는 것이 핵심 기술이다. 본 논문에서는 다양한 방전원에 대한 신호 유형을 정리하고 방전원별 특성을 추출하여 실제 부분방전 발생시 방전원을 쉽게 유추할 수 있도록 하였다.

본 논문에서는 배전반 또는 분전반에서 널리 이용되고 있는 1000 V 이하의 배선용 차단기, 즉 MCCB(Molded Case Circuit Breakers)의 신뢰성을 평가하기 위한 시험계획 및 시험방법을 검토하기 위한 전단계에서 반드시 필요한 고장모드영향분석(FMEA)의 결과를 서술하고, 또한 고장모드별로 대응되는 스트레스를 이용한 신뢰성평가 방안에 대해서 제시한다.

In this paper, a novel method has been proposed by use of HY-Pockels sensor for the detection of PD in GITR(Gas Insulated Transformer) in order to improve reliability and to overcome the shortcomings of other techniques which are currently employed. For this work, different types of the test specimen, simulating the winding of the real GITR, have been designed and fabricated to generate the PD. And then, the detection of PD has been realized by conventional methods according to IEC 270 and also the proposed novel sensor as well. Afterwards, their results are well compared to understand the correlation between the nature of the defects in the winding and their PD pattern.

한류형 휴즈는 크게 저압, 고압 및 초고압 한류형 퓨즈의 3종류로 분류할 수 있다. 저압형(정격전압 200/380/660V)은 주로 전원장치 보호용으로 인버터 및 UPS에 적용되고 있으며, 고압형(정격전압 3600/7200v)은 전력계통에서 수변전설비의 고압에 적용되어 VCB, 변압기, MOTOR 및 MOLD PT 등을 보호할 목적으로 사용되고 있다. 또한 초고압형(정격전압 24000/25800v)은 수배전설비의 고압에 적용되어 발전기 및 변압기 둥을 보호할 목적으로 사용되고 있다. 한편, 한류형 퓨즈의 성능 및 수명을 결정하는 요인은 용단시간, 동작 특성 및 내습성에 의해 결정된다. 따라서, 환경요인(온도, 습도 및 전류)을 변화시켜 성능을 저하시킨 후 과전류를 인가하면 수명저하의 경향을 분석할 수 있다. 국내에서 생산하고 있는 저압, 고압 및 초고압 한류형 퓨즈의 신뢰성이 향상되면 전력계통에서의 신뢰성을 확보할 수 있고 따라서 대형사고로의 발전 가능성을 줄일 수 있다.

본 논문에서는 패러데이 효과(Faraday effect)를 이용하여 초고압 전력설비에서 대전류 측정을 위한 광CT의 온도변화에 따른 특성에 대한 기초 연구를 하였다. 광원으로는 1310[nm] Laser Diode를 사용하고 수신부로는 PIN-Photodiode를 사용하였다. 실험을 위한 온도변환장치는 GIS와 같은 모양으로 재철은 알루미늄으로서 제작하였다. 광의 전송로는 파이버 내에서 편광상태를 유지할 수 있는 30[m]의 싱글모드 언재킷(unjacked) 파이버를 사용하였다. 전류의 측정은 400[A]에서 1300[A] 까지의 범위에서 측정하였으며 온도는 -40[$^{\circ}$]에서 50[$^{\circ}$]까지 10[$^{\circ}$]씩 증가시키면서 측정하였다. 이 때 출력선호는 인가전류의 중가에 따라 비례하여 증가하였으며 주변온도가 높을수록 비례하여 증가하였다.

In this paper the imitated electric defect was simulated by insulation particle in the model GIS. This paper studied the distribution of frequency spectrum of the radiated electromagnetic waves using antenna (30-2,000[MHz]) and spectrum analyzer. From results of this study, a new method was introduced for measurement and analysis of the radiated electromagnetic waves in accordance with discharge progress of each defect in the model GIS. It was confirmed that detecting partial discharge and estimating discharge progress can be possible in the model GIS.

본 논문은 그루빙(grooving),타이닝(tinning),텍스쳐(texture) 등의 포장 도로의 표면 상태를 고성능의 레이저 변위센서를 사용하여 정밀하게 측정하고, 측정한 표면 상태를 객관적으로 평가하는 장비 개발에 관한 논문이다. 본 논문에서는 실제 평가 장비 차량을 만들기에 앞서 전체 시스템을 설계하고, 실내에서 차량과 도로의 모사 장비를 만들어 실험하였다. 본 실험에서는 오실로스코프와 DAQ (Data Aquisition) 보드를 사용하였다. LabView로 선호처리 프로그래밍을 하여 컴퓨터 화면에 GUI 형태로 나타내었다. 측정 데이터는 컴퓨터의 저장 공간에 저장하여 후처리를 가능하게 하였다. 또한, 실제 평가 장비 차량에 장착하게 될, GPS(Global Positioning System) 시스템으로 부터 실시간으로 평가 장비 차량의 이동거리 데이터를 얻었다. 실험 결과 차량이 80km/h로 주행할 때 도로 표면 타이닝의 폭과 깊이가 평균 9.67% 오차를 보였으며, 이동거리는 0.03% 이내의 오차를 보여 만족할 만한 결과를 얻었다.

In order to obtain a low-loss ferroelectric phase shifter, the reflection-type phase shifter with ferroelectric defected ground structure (DGS) resonators has been designed in this paper. The proposed phase shifter is consist of a 3-dB $90^{\circ}$ branch-line hybrid coupler and terminated reflective circuit with tunable ferroelectric DGS resonator. The ferroelectric DGS unit structure can provide high Q resonator characteristic at high frequencies. The design parameters of equivalent circuit for the tunable DGS resonator are derived by using simple circuit analysis method and three-dimensional full wave finite element method. The fabricated phase shifter has an insertion loss of better than 3.4dB at 13.5GHz.

본 논문에서는 S/C-밴드(2${\sim}$8GHz)에서 동작하는 초광대역 주파수 합성기를 설계하였다. 먼저 S-밴드(2-4GHz) 광대역 전압제어발진기를 가지고 획득시간을 단축하기 위한 연산 증폭기를 사용한 DA변환기와 능동루프 필터(Active Loop Filter)로 구성된 S-밴드 주파수 합성기를 설계하였다. 그리고 주파수 체배기, SPDT RF 스위치를 통합하여 최종적으로 S/C-밴드 초광대역 주파수 합성기를 설계하였다. 제작된 주파수 합성기는 200kHz 비교주파수에서 위상잡음은 100kHz 옵셋 주파수에서 -92dBc/Hz이하, 불요주파수 특성은 -62.33dBc 이하, 획득시간은 1.3ms 이하로 측정되었다.

Distributed optical feedback by gain coupling in V-groove quantum-wire lasers is investigated using InGaAs/AlGaAs active materials grown by metalorganic chemical vapor deposition (MOCVD). In order to avoid grating overgrowth during the fabrication of DFB structures, a newly developed constant MOCVD growth method is employed. Gain anisotropy in emission spectra near Bragg wavelength, resulting from optical feedback along the DFB direction, is clearly observed at room temperature.

본 논문에서는 초광대역 기술을 이용한 고정밀 위치 추적용 센서를 위한 소형, 저가의 안테나를 제안한다. 안테나는 Fat monopole 과 유사하지만, Fat monopole의 상대적인 협대역 특성을 개선하기 위해 탭을 부가하여 고주파에서의 특성을 향상시켰다. 또한 급전은 제작이 용이한 Coplanar 도파관 구조를 사용하였다. 검증을 위해 3.1GHz${\sim}$5.1GHz 대역에서의 고 정밀 위치 추적용 센서를 위한 안테나를 설계하였다. 상용 EM 프로그램을 사용하여 안테나의 치수들에 대한 최적화 작업이 이루어 졌다. 실제 제작 결과와 시뮬레이션 결과가 비교되었고 상당히 일치함을 확인 할 수 있었다. 제작된 안테나는 2.5GHz${\sim}$7GHz대역내에서 10dB이상의 Return loss를 가졌다.

The grounding system design of the communication base station can be on the unfavorable conditions to induce the safe designing because of the limited area of the communication base station and the week point of surge caused by the given geographical condition such as the top point of mountain. In this paper, it is examined throughly about the way of safe designing that can reduce GPR(Ground Potential Rise) within the normal frequency band. And it is also considered the effective counter plan to cope with a transient phenomena that happen when surge of scores MHz-band inserted.

In this paper, a lumped equivalent circuit for a conventional parallel directional coupler is proposed. The equivalent circuit and design formula for the presented lumped element coupler is derived based on the even- and odd-mode properties of a parallel-coupled line. By using the derived design formula, we have designed the 3dB and 4.7dB lumped element directional couplers at the center frequency of 3.4GHz and 5.6GHz. A chip type directional coupler has been designed to fabricate with MMIC(Monolitic Microwave integrated circuit) process. Excellent agreements between simulations and measurements on the designed directional couplers show the validity of this paper.

In this paper, electromagnetic wave environment generated from electronic equipments was investigated. Since the main source of electromagnetic waves are electronic equipments, the field intensity of a harmful electromagnetic wave was measured and its harmful level was analyzed. It was also found that the result was 23%${\sim}$38% in case of TV set and microwave oven. Based on this analysis, this study proposed efficient shielding method to suppress unwanted electromagnetic wave.

In this paper, a low noise amplifier (LNA) in receiver of Low Noise Block Down Converter (LNB) for direct broadcasting service (DBS) is implemented by using GaAs HEMT. The LNA is designed for operation between 10.7GHz-12.7GHz. The LNA consists of input, output matching circuits, DC-blocks and RF-chokes. Simulation result of the LNA shows that a noise figure is less than 1.4dB and a gain is greater than 9.2dB in the bandwidth of 10.7 to 12.7GHz with good flatness of 0.1dB.

고전압 전력기기분야에 광섬유 전압센서를 적용해보고자하는 연구는 20여년 전부터 꾸준히 진행되어 왔었다. 본 연구에서는 구조가 간편한 광섬유 패브리페로 간섭계를 이용한 고전압기기 적용형 전압센서가 시도되었다. 신호변환은 정전력을 이용하여 전압의 변화를 광섬유스트레인센서로 검출하며, 해상도를 확보하기 위하여 공진기의 길이를 1cm, 위상을 스캐닝하는 변조방법을 적용하였고, 교류전압 1000V까지 적용 타당성을 시험하였다.

This paper presents a miniature optical system for the fluorescence detection of the patterned protein chip. The patterned protein chip was fabricated using MEMS process. The fluorescence from the patterned protein chip was measured while varying the concentration of the BSA. The fluorescence light is separated spatially from the excitation beam using mini-size prism to increase SNR (Signal-to-Noise Ratio). The combination of prism and mirrors can convert the excitation light from the laser diode to uniform illumination on the specimen. We believe that the proposed system for fluorescence detection can be applied to rea1ization of point-of-care.

This thesis complemented the weak points that the existing theses did not represented a phase characteristic as the equivalent circuit by applying 4-port simulation to DGS (Defected Ground Structure) characteristic and an equivalent circuit, which are the transmission line structure that has the defect made in the ground surface. We used a distribute device and a lumped device, obtained the equivalent circuit by applying the structure of balun to a discontinuous part. An indicated DGS (Defected Ground structure) is a dumbbells-shaped single defect, we indicated satisfying a magnitude and phase characteristics by applying this equivalent circuit.

In this paper, we have proposed a novel omnidirectional power divider/combiner configuration. By using the even- and odd- mode analysis. we analyse the proposed power divider/combiner circuit. In order to show the validity of the presented power divider/combiner circuit. We have designed and implemented the proposed circuit of the center frequency of 2.3GHz.

Bow-tie 마이크로스트립 패치형태로 초광대역 안테나를 설계 제작하였다. 보다 광대역화된 특성을 얻기 위해 급전구조 변화와 반원형태의 기생페치를 추가하였다. 제작된 안테나는 입력단자 부분의 접지면을 전제하고 VSWR${\leq}$2를 기준으로, 슬롯형태가 아닌 패치형태로도 2.3GHz${\sim}$5.5GHz까지 대역폭비 2.4 : 1의 초광대역 특성을 나타냈다. 또한, 수평 단면 패턴에 대하여 넓은 주범을 가지며, 전 대역에서 안정된 방사패턴을 유지 하였다.

The TX/RX broadband L-type circular polarization antenna using LTCC at K/Ka band has been presented. This antenna has been analyzed in compensation for LTCC with relative permittivity 5.2 and could have been integrated with RF component. As the measured 10dB impedance circular polarization bandwidth of the proposed antenna is 7%(20.8GHz${\sim}$22.2GHz) at the K band and 2.3%(30.9GHz to 31.6GHz) at the Ka band. Also the gain of the antenna is -0.7${\sim}$3.05dBi at the K band and -2.8${\sim}$1dBi at the Ka band. The purpose of the research is to design an efficient antenna structure for satellite communication at K/Ka band. the antenna should be used for both TX and RX frequency bands. The antenna will be mounted on LTCC(Low Temperature Co-fired Ceramic) so that it can be integrated with other RF circuits. This research is important because of the following reasons. 1) The frequency ranges of satellite communication tends to move up to higher frequency such as Ka band or milimeter wave band. 2) Design of antenna for smaller size, lighter weight and less loss is preferred by most RF engineers. 3) Antennas on LTCC enables to integrate the antenna with other RF circuits, and thus, one can reduce the size and loss of the RF system.

The Ku band that has been using for the satellite communication and broadcasting would be changed to K/Ka bands. The satellite system requires the antenna structure to fabricate low loss and small antenna that is able to be integrated with other Rf circuits for both Rx and Tx. So we should design it with dual feed antennas at K/Ka bands, high isolation between two different feeds and broadband circular polarization. This paper proposes the LTCC(Low Temperature Co-fired Ceramic) process for integration with other Rf circuits and the Axial mode of the helical antenna to satisfy those requirements.

In this paper, circular polarized antennas of Tx 30GHz and Rx 20GHz are implemented in LTCC process. Tx antenna has a circular patch structure and Rx antenna has a ring patch structure. The feeding line of Tx antenna is placed in the center hole of Rx ring patch antenna which is printed under Tx circular patch antenna layer. It makes antenna size smaller. Tx antenna's return loss in under -10dB level from 30GHz to 31GHz and Rx antenna is under -10 dB from 20GHz to 21GHz. The isolation between two antennas is less than -20dB. Axial ratio is less than 3dB though out each band.

본 논문에서는 짧은 결합 길이를 갖는 평면형 초소형 발룬 및 평형 필터를 설계한다. 구조상 물리적인 접지를 사용하지 않기 때문에, 설계한 평형 필터의 잡음을 최소화할 수 있다. 설계한 발룬은 0.05dB의 크기 평형성과 $0.7^{\circ}$의 위상 평형성을 갖는다. 평형 필터의 측정 결과, 500MHz의 중심 주파수를 기준으로 10%의 대역폭을 가지며, 반사 손실 7dB, 삽입 손실 8dB의 특성을 보인다. 또한 통과 대역에서 크기 평형성이 0.2dB, 위상 평형성이 $1.2^{\circ}$ 의 평형성을 갖는다. 설계한 발룬과 평형 필터는 MMIC나 LTCC공정을 이용하여 구현가능하고, 그럴 경우 손실을 더 줄일 수 있고, 잡음 성능을 개선시킬 수 있다.

본 논문에서는 새로운 개념인 능동 고조파 결합을 이용한 4위상 전압제어 발진기를 설계, 제작하였다. 4위상 출력 특성을 얻기 위하여 각각의 차동 VCO의 가상 접지(Virtual Ground)면을 본 논문에 제시된 능동 고조파 결합 회로(Active super harmonic coupling)을 이용하여 결합시키는 방법을 적용하였다. 제안된 구조는 다음과 같은 장점을 가지고 있다. 결합구조를 갖는 트랜지스터에 부가적인 전류소비를 줄일 수 있으며, layout상에서 문제되었던 대칭구조를 개선할 수 있다. 또한 기존에 발표되었던 방법인 passive transformer를 이용한 고조파 결합 보다 회로 크기를 줄일 수 있다. 측정결과 출력 전력 -12dBm, -117dBc/Hz @1-MHz 이하의 위상잡음 특성, 2.66GHz${\sim}$2.91GHz의 250 MHz 주파수 가변, 25dB이하의 2차고조파 억압, 7 mA 의 전류 소모(buffer amp. 포함되지 않음)를 가졌다.

본 논문에서는 전통적인 헤어핀 공진기보다 훨씬 소형화한 헤어핀 공진기 구조를 이용하여 X 대역 MMIC 발진기를 InGaP/GaAs HBT 공정을 이용하여 제작하였다. 헤어핀 공진기의 크기는 약 1/4정도로 작게 구현이 가능하였으며, 이를 적용한 발진기의 측정결과 주파수는 8.295 GHz, 출력전력은 4.8 dBm, 위상잡음특성은 100 kHz 옵셋 주파수에서 -106.8 dBc/Hz, 1 MHz 옵셋 주파수에서 -121.7 dBc/Hz를 각각 나타내었다.

극 초단의 임펄스를 사용하여 지중 매설물을 탐색하기 위한 지반탐사 영상 레이더를 개발하였다. 개발된 지반 탐사 레이더는 Gaussian 임펄스, 임펄스 송수신을 위한 초 광대역 소형 모노폴 안테나, 수신 신호 저장을 위한 고속 A/D로 구성된다. 탐지 깊이와 시스템의 크기를 고려하여 임펄스 발생기 및 초광대역 안테나가 설계되었다. 지중 매설물의 영상화를 위해 여러 가지 이미지 기법이 사용되었다. 발표에서는 구현된 시스템의 시제품을 소개하고, 개발된 시제품을 사용하여 가상의 모래 시험장에서 측정된 결과를 보일 것이다.

본 논문에서는 nonradiative dielcctric (NRD) 도파로를 이용하여 28GHz대에서의 single balanced mixer를 설계하였다. 혼합기에 필요한 $90^{\circ}$ hybrid direction기 3dB 결합기를 NRD 도파로를 이용하여 설계 하였고 CST MWS를 이용하여 설계 결과를 검중 하였으며 결과는 중심 주파수 28GHz에서 대역폭이 1GHz의 결합기를 설계하였음을 확인할 수 있었다. 이와동시에 다이오드를 부착하기 위해 NRD 도파로와 마이크로스트립의 매칭 구조를 1 pole UDR과 patch를 이용하여 혼합기를 설계, 제작하였다.

This paper study on OLEDs(Organic Light Emitting Diodes) panel using PLD(Pulsed Laser Deposition) methode. Deposition of organic was used Q-stitched Nd/YAG laser in 355 nm and reduced organic pellet for PLD method. Organic morphology was measured AFM(Atomic Forced Microscope) and emitting efficiency was measured luminance meter.

Variable Structure Controller with effective tracking performance is propose to control micro actuator system. Propsed VSC(Variable Structure Control) technique is implemented to tracking control of comb driving system having high non-linearity. The tracking performance due to VSC technique is compared to conventional PD(Proportional Derivative) control technique, reveals improved results.

Capacitive pressure sensor는 Piezo type sensor에 비해 온도의 영향이 적어 공업계측, 전기용품 등 그 용도가 다양하여 폭넓게 사용되어지고 있지만, 측정값의 비선형성이 존재하여 측정값에 대한 신뢰도가 떨어지는 단점이 있다. 본 연구에서는 기존 capacitive pressure sensor의 비선형적 output을 개선하기 위한 방법으로 touch mode capacitive pressure sensor를 제안하였다. 또한, 실제 Device제작에 앞서 FEM 해석을 수행하였다. 2mm X 2mm 크기의 diaphragm, $25{\mu}m$의 두께, $20{\mu}m$의 gap을 갖는 Sensor를 Simulation하였으며 설계 변수를 추출하여 각각의 설계변수에 대한 해석을 실시하였다. 그 결과 15.2psi${\sim}$31psi의 영역에서 8.58pF${\sim}$54.31pF의 capacitance가 선형적으로 나타나는 sensor임을 확인하였다.

In this paper, the new measurement methodology of characteristics of the vibratory micro gyroscope using Quality factor and the resonant displacement was proposed. Because the Quality factor has a large error under the high Quality factor condition, it is difficult to analyze the characteristics of the vacuum packaged vibratory micro gyroscopes with the Quality factor. We analyzed mechanical characteristics of gyroscope with the value of Quality factor. We described measurement errors of mechanical characteristics of micro gyroscopes. The measured value of Quality factor is 47532 and error range of Quality factor is from -29.8 % to 73.9 %. The value of resonant displacement is 3.4${\mu}m$ and the measurement error is 2.9 %. From the result of Quality factor degradation and resonant displacement degradation, 1698 days and 1503 days were estimated as Time To Failure (TTF), respectively. The range of estimation error of Quality factor degradation and resonant displacement degradation is calculated from 1246 days to 1832 days and from 1456 days to 1537 days, respectively. We can analyze the characteristics of the vibratory gyroscope using the quality factor when the Quality factor is smaller than 10,000. Also we can analyze that using the resonant displacement when the Quality factor is larger than 10,000.

본 논문은 압전소자를 구동장치로 사용한 마이크로 펌프의 제작과 실험에 관한 논문이다. 마이크로 펌프의 상부기판은 polydimethyl siloxane(PDMS)을 소재로 미세유로에 상시 닫힌 밸브가 일체화된 구조로 제작되었고, 하부기판은 polymethyl methacrylate(PMMA)를 소재로 3개의 압전 디스크가 구동기로 부착되었다. 최종적으로 상, 하부 기판은 액상 PUMS로 접합하여 제작했다. 구동기의 입력신호는 6상으로 구형파를 인가하여 연동구동하며 주파수와 전압을 가변하면서 유량을 측정하였다. 구동 주파수가 0.167 Hz이고 전압이 20 V일 때, 마이크로펌프의 1회 토출량은 104 nl이고, 유량은 1.04${\mu}{\el}$/min이다.

본 논문은 마이크로 유체 소자의 소재로서 많이 쓰이고 있는 poly(dimethyl-siloxane) (PDMS)의 친수성 유지를 위한 표면 개질에 대한 연구이다. PDMS는 유연성, 투명성 등의 다양한 장점을 가지고 있으나, 높은 소수성으로 인하여 유체 소자로의 응용에 제한을 갖는다. 기존 연구에서 수행한 산소 플라즈마 후 2-Hydroxyethyl methacrylate (HEMA) 처리에 의한 PDMS의 표면 개질은 친수성 유지 시간에 한계가 있었다. 이에 친수성 유지 시간을 증가시키기 위하여 경화된 PDMS에 두 시간의 오존 처리 후, 6시간 동안 monomethyl ether hydroquinone (MEHQ)가 제거된 HEMA로 표면을 개질한다. 표면 처리된 PDMS의 친수성 특성을 확인하기 위해 접촉각을 측정하였다. 측정 결과, 오존을 이용하였을 때 $60^{\circ}$ 이하의 낮은 접촉각이 900시간 이상 유지됨을 확인하였다.

본 연구에서 제안하는 마이크로 시스템은 열공압 방식으로 구동되고 제작비용이 저렴한 indium tin oxide (ITO) 및 polydimethylsiloxane (PDMS)로 제작되었다. 제안된 마이크로 밸브와 마이크로 펌프의 구조는 ITO 히터, SU-8 층, PDMS membrane, 그리고 PDMS 채널로 구성 되어 있다. 제안된 마이크로 펌프와 마이크로 밸브는 제작 공정 및 구조가 간단하고 값이 저렴하며, 마이크로 펌프와 마이크로 밸브를 같은 기판 위에 쉽게 직접화할 수 있는 장점을 가진다. 마이크로 밸브의 유량은 채널 폭에 비례하며 밸브가 closing 되는 전력은 채널의 폭과 상관없이 100 mW이다. 마이크로밸브의 ITO 히터의 온-오프에 따라 유량이 매우 잘 제어되었다. 제안된 마이크로 펌프의 경우, 히터의 인가 펄스 전압이 증가함에 따라 유량은 선형적으로 비례 증가함을 관찰할 수 있다. 마이크로 펌프의 최대 유량은 펄스 전압과 duty 비가 55V와 10%일 때 6 Hz에서 78 nl/min이 측정 되었다.

In this study, sheathless electrospray from PDMS/glass microchips with conducting metal emitter tip is described. A chip-based capillary electrophoresis/mass spectrometry (CE/MS) system has advantages of the CE separation and on-line electrospray detection of peptide solution. We have fabricated a new electrospray ionization(ESI) device composed of the metal emitter tip and CE separation channel monolithically in a glass microchip. The separation channel and metal emitter tip are fabricated using a glass wet etching and gold electro plating process, respectively. The fabricated micro electrospray chip was tested by spraying peptide sample for mass spectrometric analysis. Singlely-charged peak and doublely-charged peak of peptide were detected and further MS/MS fragmentation was performed in each peak. Direct comparisons with conventional glass or fused silica emitters showed very similar performance with respect to signal strength and stability.

In this study, Spiral inductors on the $SiO_2$/Si(100) substrate were fabricated by the magnetron sputtering method. Cu thin film with the thickness of 2 ${\mu}m$ was deposited on the substrate. Also we fabricated square inductors through the wet chemical etching technique. The inductors are completely specified by the turn width and the spacing between spirals. Both the width and spacing between spirals were varied from 10 to 60 ${\mu}m$ and from 20 to 70 ${\mu}m$, respectively. Inductance and Q factor dependent on the RF frequency were investigated to analyze performance of inductor arrays. Also, We recommend that the reasonable Q-factors, spec's turns and thickness of the coil for inductors cab be set to be ideal condition.

In this paper, a novel tunable bandpass filter using tunable series inductors and MEMS switches for wireless LAN applications was proposed. The proposed tunable filter was fabricated using a micromachining technology and performances of the fabricated filter were estimated. The filter consists of spiral inductors, MIM capacitors and direct-contact type MEMS switches, and its frequency tunability is achieved by changing the inductance that is induced by ON/OFF actuations of the MEMS switches. The actuation voltage of the MEMS switches was 58 V, and the measured center frequencies were 2.55 GHz and 5.1 GHz, respectively. The passband insertion loss and 3-dB bandwidth were 4.2 dB and 22.5 % at 2.55 GHz, and 5.2 dB and 23.5 % at 5.1 GHz, respectively.

대형 조물은 안전관리 시스템의 법제화로 스트레인 게이지, 가속도 센서 등을 이용하여 상시 관리를 의무화 하고 있다. 상시 계측을 위해 유선 센서의 경우 데이터 전송의 신뢰성은 있지만 선로 결선의 문제점 때문에 무선 센서의 적용이 요구된다. 하지만 무선 센서의 경우, 전원공급의 문제를 갖고 있어 장차이 어려운 실정이다. 본 연구에서는 압전체를 이용하여 무선 센서의 전원 공을 위한 에너지 변환 시스템을 제안하였다. 이 시스템은 구조물 내부의 진동을 전기 에너지로 변환, Capacitor에 저장 후, 데이터 전송을 위해 일시에 방출하는 구조이다. 20m의 무선 데이터 통신을 위해 2.43mJ(5V*49mA*10ms)의 전력량이 필요한데, 모의 교량 모델에 시스템을 적용한 결과 2분 30초 동안의 진동 에너지가 2.8mJ의 전기 에너지로 저장되었다. 이 실험 결과를 토대로 무선 센서를 이용한 상시 모니터링이 가능함을 예상할 수 있다.

센서의 소형화 되는 추세에 전극 면적은 sensitivity의 중요한 요인이다. 본 연구에서는 콜레스테롤을 측정하기 위해 각각 planar 전극과 porous 전극에 효소 고정화 방법으로 covalent binding인 silanization 공정을 이용하여 전극 면적에 따른 전기화학적 감도를 비교하였다. Handles-Sevcik equation을 이용하여 전극 면적을 구한 결과 planar 전극의 경우 0.1608 $cm^2$, porous 전극의 경우 0.5054 $cm^2$로 porous 전극 면적이 planar전극에 비해 약 3.1배 증가하였다. 또, planar 센서의 sensitivity는 0.08567 ${\mu}A/mM{\cdot}cm^2$이고 porous 센서의 sensitivity는 planar sensor에 비해 약 3.1배 증가한 0.2656 ${\mu}A/mM{\cdot}cm^2$였다. 따라서 porous sensor의 sensitivity의 증가는 전극 면적의 증가에 따른 것이라고 할 수 있다.

본 논문은 UV-LIGA 공정, 후막공정을 이용한 바이오센서용 magnetic bead 분리 장치의 제작 기술개발에 관한 것이다. 최근 MEMS(microelectromechanical system) 기술을 이용한 바이오센서에 대한 연구가 활발하게 이루어지고 있다. 이러한 바이오센서 분야 중 혈액이나 다른 원하지 않는 물질을 분리해 주는 분리장치는 MEMS 기술을 이용해 구현이 매우 어려운 부분 중에 하나이다. 기존의 UV-LIGA 공정과 도금법을 이용한 마이크로 전자석 제작하여 분리장치를 제작하는 경우 제작 공정이 매우 복잡하며 매우 많은 공정비용을 요구한다. 이러한 단점을 해결하기 위해 본 논문에서는 Sr 계연의 고분자 자석과 3차원 PDMS(poly-dimethylsiloxane) 마이크로 채널 공정을 이용해 분리장치를 제작하였다. 제작된 분리장치는 $0{\sim}30{\mu}{\ell}$/min 의 속도에서 유체를 흘렸을 90% 이상의 분리 효율을 나타냈다. 개발된 분리 장치는 연재질의 PDMS 로 제작되어 일회용 바이오센서에 적용이 가능하다.

전기화학발광(ECL) 시스템은 높은 감도와 넓은 선형동작영역을 가지므로 분석화학에서 넓게 연구 되고 있다. 그러나 포토멀티플러, 광섬유와 플루오르메터로 구성된 ECL 검출 시스템은 크기가 크고, 전력소모가 많으며, 고가인 단점이 있다. 따라서 이러한 단점을 보완하기 위해 p+n 포토다이오드를 이용한 마이크로 ECL시스템을 제작 과산화수소 농도를 50uM${\sim}$10mM 범위에서 측정하였고, 글루코오스는 1mM${\sim}$20mM 농도범위에서 측정하였다. 따라서 마이크로 ECL 시스템이 바이오센서 혹은 바이오 분석기로써의 가능성을 확인 하였다.

In this paper, a DNA chip with a microelectrode array was fabricated using microfabrication technology. Several probe DNAs consisting of mercaptohexyl moiety at their 5 end were immobilized on the gold electrodes by DNA arrayer. Then target DNAs were hybridized and reacted with Hoechst 33258, which is a DNA minor groove binder and electrochemically active dye. Linear sweep voltammetry or cyclic voltammetry showed a difference between target DNA and control DNA in the anodic peak current values. It was derived from Hoechst 33258 concentrated at the electrode surface through association with formed hybrid. It suggested that this DNA chip could recognize the sequence specific genes.

High throughput analysis using a DNA chip microarray is powerful tool in the post genome era. Less labor-intensive and lower cost-performance is required. Thus, this paper aims to develop the multi-channel type label-free DNA chip and detect SNP (Single nucleotide polymorphisms). At first, we fabricated a high integrated type DNA chip array by lithography technology. Various probe DNAs were immobilized on the microelectrode array. We succeeded to discriminate of DNA hybridization between target DNA and mismatched DNA on microarray after immobilization of a various probe DNA and hybridization of label-free target DNA on the electrodes simultaneously. This method is based on redox of an electrochemical ligand.

모세관 전기영동 및 전기화학적 검출 시스템을 마이크로 시스템에 적용하여 ITO 유리기판과 polydimethylsiloxane (PDMS)로 제작하였다. 제작된 모세관 전기영동 및 전기화학적 검출 시스템은 일회용으로 사용가능하며 전기화학적 검출에 아주 적합한 특성을 보인다. 모세관 전기영동 및 전기화학적 검출 시스템은 주입과 분리 채널 (80 ${\mu}m$ 폭 ${\sim}$ 40 ${\mu}m$ 깊이)을 가진 PDMS 층과 유리기판 위에 검출 전극으로 사용되는 ITO가 형성된 층으로 구성된다. PDMS 층과 ITO 유리 기판은 UV-$O_3$ cleaner를 사용하여 접합하였다. 완충용액은 10 mM 2-(N-morpholino)ethanesulfonic acid (MES)를 사용하였고 분석물질은 1 mM 농도의 dopamine과 1 mM 농도의 catechol을 사용하였다. 60 V/cm 전계로 주입 및 분리를 하였으며 작업전극과 기준전극 간의 전위는 +600 mV로 유지하며 분석물질의 농도에 비례하는 전류량법으로 측정하였다. 전기화학적 검출 회로는 천기영동 전계의 간섭으로부터 분리하였다. 10 mM MES 완충용액에서 바탕 전류의 크기가 ${\sim}$10 pA 일 때 측정전류 값은 10 nA이다. 측정된 피크 값은 기존의 Au 전극과 비교하여 선택성, 감도, 분해능이 유사한 특성을 보여준다.

A microcantilever-based biosensor with piezoresistor has been fabricated using surface micromachining technique, which is cost effective and simplifies a fabrication procedure. To evaluate the characteristics of the cantilever, the cystamine terminated with thiol was covalently immobilized on the gold-coated side of the cantilever and glutaraldehyde that would be bonded with amine group in the cystamine was injected subsequently. This process was characterized by measuring the deflection of the cantilever in real time monitoring. Using a piezoresistive read-out and a well-known optical beam deflection method as well carried out the measurement of deflection.

Cancer cell lysis at pulsed DC is realized using micromachined electrodes. In this research, quantitative analyses are performed on cell lysis results. The cell volume increasing at the pulses applied are analyzed in different medium conditions on osmotic pressure and conductivity, and the cell lysis procedures are studied in detail experimentally. Phosphate buffered saline (PBS) is used as the medium. To change the conductivity of PBS, NaCl concentration of PBS is adjusted, and inositol is used with PBS to control the effects of the osmotic pressure to cell lysis performance.

본 논문은 전기화학 합성으로 형성한 폴리피롤(polypyrrole : PPy) 전극에 신경 전달물질(neurotransmitter)인 에피네프린(epinephrine : Ep)을 치환도핑하여 전압인가에 따른 방출과 자외선 분광법에 의한 검출 결과를 보인다. 폴리피롤 막은 정전압법으로 금 전극에 합성하였고, potassium phosphate buffer(pH 7.0) 내에서 에피네프린을 폴리피롤 막에 치환도핑하였다. 폴리피롤 막에 10mM Ep 농도로 치환도핑한 후 염화나트륨 수용액에서 -0.9V의 환원전압을 인가하여 에피네프린을 방출하였다. 자외선 분광법을 이용하여 파장 250$^{\sim}$400nm 영역에서 방출된 에피네프린 용액의 최대흡광도가 약 0.021 임을 확인하였고 이는 에피네프린 표준용액의 정량선으로부터 16${\mu}$g 이 방출되었음을 의미한다.

본 논문은 미세공정을 이용하여 다중전극을 배열하여 전압 인가에 의해 선택적으로 약물 방출이 가능한 구역화된 약물 저장용 구조물의 설계 및 제작에 관한 것이다. 두께 525${\mu}m$ 언 (100) Si wafer를 이용하여 TMAH 용액의 조성 및 온도에 따라 Si 식각 기초실험을 하고 그 결과를 이용하여 최적 식각조건을 설정하였다. 구조물 opening 크기를 다양하게 설계하여 미량의 약물을 선택적으로 방출할 수 있게 하고자 역 피라미드 형태의 약물 저장용 구조물을 제작하였다. 전압 인가에 의한 약물 방출시 Au 전극의 특성을 고찰하고자 저장 구조물 위에 anode의 면적과 anode 전극간 거리를 변화시켜서 설계 및 제작하였고, polyimide를 전극 사이의 절연막으로 이용하였다. 제작된 구조품의 전극 특성은 5V의 설정전압을 인가하였을 경우 2500s 동안 0.25mA로 안정적으로 유지되었으나 10V, 15V, 20V일 경우 전극의 산화현상으로 Au 전극이 부식이 되어 전류가 안정적으로 흐르지 않는 것을 알 수 있었으며, 약물전달시스템에서 안정적인 전류 공급을 위해서는 Au 전극이 산화 되지 않는 전압 인가 조건 및 시간은 설정해야 함을 알 수 있었다.