전계가 있는 밀폐된 공간에서의 대전입자에 작용하는 힘에 대한 수식들을 정의하고 구동 전압을 추출할 수 있는 상관 관계를 살펴보았다. 입자의 크기, 전하량 등 여러 가지 실험적인 factor들을 변화시켜본 결과 구동 전압에 많은 영향을 주는 것으로 나타났다. 특히 구동 전압의 추출을 위해 도입된 여러 가지 factor들은 구동 전압에 독립적으로 작용하는 것이 아니라 서로 복합적인 작용을 하는것으로 결과가 얻어졌다.

A high performance organic phototransistor with dynamic range of 120 dB is demonstrated by employing soluble pentacene as a photo-sensing layer. The organic phototransistor used suspended source/drain (SSD) electrode structure, which provides a dark current level of ${\sim}10^{-14}$ A at positive gate bias. Under a steady-state illumination, the organic phototransistor exhibited a current modulation of $10^6$ compared to dark to give a dynamic range of 120 dB. These results suggest that the organic phototransistor based on TIPS pentacene can be a new premising candidate for low-cost and high-performance photo-sensing element for digital imaging applications.

열처리 조건이 이종접합 유기태양전지(heterojunction organic photovoitaics)의 power conversion efficiency(PCE)에 미치는 영향에 대해 살펴보았다. 본 연구에서는 열처리 온도와 열처리 시간을 변수로 다양한 조건하에서 유기태양전지를 제작하고 AM1.5G 조건에서의 효율 변화를 관찰하였다. 열처리 온도는 $90^{\circ}C$, 열처리 시간은 20분에서 가장 우수한 변환효율이 관찰되었다.

In magnetic field analysis of electrical machines, hysteresis phenomena of B-H curves should be taken into account in order to obtain more accurate results. In this paper, the hysteresis modeling using the micromagnetics for the magnetic field analysis is investigated. In the micromagnetics, usually, it takes much CPU times. Therefore, the method for representing hysteresis phenomena by minimum modeling is investigated in order to applying it to the magnetic field analysis. First, the micromagnetics is described. Then, the method of minimum modeling is shown. Finally, the hysteresis curve obtained by the minimum modeling is demonstrated. The effect of parameters of micromagnetics on the shape of hysteresis curve is investigated.

An amperometric glucose biosensor has been developed using viologen derivatives as electron mediator of glucose oxidase (GOD) at Au electrode. Highly stable self assembled monolayer (SAM) of thiol-based viologen is immobilized onto the Au electrode followed byGOD is immobilized onto the viologen modified electrode. This biosensor response to glucose was evaluated amperometrically in the potential of -300 mV. Upon immobilization of glucose oxidase onto the viologen modified-electrode, the biosensor showed rapid response towards glucose. Experimental conditions influencing the biosensor performance such as, pH, potential were optimized and assessed. This biosensor offered an excellent electrochemical response for glucose concentration below ${\mu}mol$ level with high sensitivity and selectivity and short response time. The levels of the RSD's (< 5 %) for the entire analyses reflected the highly reproducible sensor performance. Using the optimized a linear relationship between current and glucose concentration was obtained up to $4.5{\times}10^{-4}$ M. In addition, this biosensor showed well reproducibility and stability.

ZnO thin films were deposited on $Al_2O_3$ (alumina) substrates by pulsed laser deposition (PLD) using Nd:YAG laser with a wavelength of 355nm, at room temperature and oxygen partial pressure of 1, 10, 30, 50, 100, and 200m Torr. Furthermore, deposited ZnO thin films were post-annealed at 400, 550, $600^{\circ}C$. The effects of oxygen partial pressure and post-annealing temperature on structural properties of the deposited films have been investigated by means of X-ray diffraction (XRD), and atomic force microscope (AFM), respectively. It has been found that ZnO thin films exhibit c-axis orientation, exhibiting an increased foil width at half maximum (FWHM) value of (002) diffraction peak at 30m Torr oxygen partial pressure and higher post-annealing temperature ($700^{\circ}C$).

Nano-sized conical-type tungsten(W) field-emitters based on carbon nanotubes(CNTs) are fabricated with the configuration of CNTs/catalyst/buffer/W-tip by adopting various buffer layers, such as TiN, Al, Al/TiN, and Al/hi/TiN. This study focuses on elucidating how the buffer layers affect the structural properties of CNTs and the electron-emission characteristics of CNT-emitters. Field-emission scanning electron microscopy(FESEM) and high-resolution transmission electron microscopy(HRTEM) are used to monitor the nanostructures and surface morphologies of all the catalysts and CNTs grown. The crystalline structure of CNTs is also characterized by Raman spectroscopy. Furthermore, the measurement of field-emission characteristics for all the field-emitters fabricated shows that the emitter using the Al/Ni/TiN stacked buffer reveals the most excellent performances, such as maximum emission current of $202{\mu}A$, threshold field of 2.08V/${\mu}m$, and long-term (up to 24h) stability of emission current.

X7R 고압용 적층 칩 캐패시터 제작을 위한 내환원성 유전체 조성물에서 희토류인 $Er_2O_3$을 0.6 mol% 첨가한 후 유리프릿 첨가시소결특성 및 절연저항이 향상됨을 확인 할 수 있었다. 회토류인 $Er_2O_3$을 첨가시 유전율 및 절연저항이 감소하는 경향을 보이나 $85^{\circ}C$ 영역에서 온도특성을 향상시키는 것을 확인하였으며 고압 적층 칩 캐패시터 제작시 온도 특성이 우수한 재료를 개발 할 수 있었다.

We have observed electrical properties of ZnO thin films for the fabrication of transparent thin film transistor. ZnO thin films were deposited on $Al_2O_3$(0001) substrate at various temperatures by pulsed laser deposition(PLD). The third of harmonic(355nm) Nd:YAG laser was used for pulsed laser deposition. X-ray diffraction(XRD), field emission-scanning electron microscope(FE-SEM), and photoluminescence were used to characterize physical and optical properties of ZnO thin film.. The results indicated the ZnO film showed good optical properties as increasing temperatures, with low FWHM of exciton-related peak and XRD(0002) peak.

A stator of ultrasonic motor of high torque with a new configuration is proposed. The stator designed newly is two sided vibrator consisting of toothed metal disk with piezoelectric ceramic ring bonded on both face of disk. which generates a flexural traveling wave along the circumference of disk. it produces a large vibrating force and amplitude because the vibrator is sandwiched by two piezoelectric ring. The finite element method was used to compute the vibration mode of the stator with a outer diameter of 48mm. A 6th vibration mode was chosen as operation mode with resonance frequency about 72kHz. According to the design, the prototype stator was fabricated and its performance was measured.

This study has successfully demonstrated the direct fabrication of polymer resistors using ink-jet printing technology as an alternative patterning to traditional photolithography. The polymer resistors were fabricated just by two layer processes using a ink-jet printer (DMP-2800, Fujifilm Dimatix). First, resistive materials was patterned by a ink-jet printing with the desired width and length. Next, resistor fabrication was completed by printing metal contact pads on the both sides of the polymer resistor. We used poly (3,4-ethylene dioxythiophene) poly(styrenesulfonate)(PEDOT:PSS) for the resistor material and a nano-sized silver colloid for the metal contact pads. We characterized the electrical properties of PEDOT:PSS by measuring sheet resistance and specific resistance on a glass substrate. From analysis of the measured resistances, the electrical resistances of the polymer resistors linearly increased as a function of printed width and length of resistors. The accuracy of the fabricated polymer resistor showed about $0.6{\sim}2.5%$ error for the same dimensions.

Polymer thick film capacitors were successfully fabricated by using ink-jet printing and screen printing technology. First, a bottom electrode was patterned by ink-jet printing of a nano-sized silver ink. Next, a dielectric layer was formed by the screen printing, then a top electrode was pattern by ink-jet printing of a nano-sized silver ink. The printed area of the dielectric layers were changed into $2{\times}2m^2$and $4{\times}2m^2$, and also the area of the electrodes were patterned with $1{\times}1mm^2$ and $1{\times}3mm^2$. The thickness of the printed dielectric layer was ranged from 1.1 to $1.4{\mu}m$. The analysis of capacitances verified that the capacitances was proportional to the area of the printed electrode. The capacitances of the fabricated capacitors resulted in one third of the calculated capacitances.

Recently, the dependence of the electric energy is increased in accordance with a growth of industry. Therefore, scientific investigation is needed for the security of electrical safety and the judgement of accident causes. Accordingly, this paper consist of the analysis for the carbonization patterns of phenolic resin and the mechanism. As the follows, spider-legs as a carbide are generated around the rods, when the electric current flows on the surface of phenolic resin. The IR absorption peak generated by the thermal effects is appeared at about $1720cm^{-1}$. As the case of Joule's heat, the crystal of a carbide is generated beca use of the rarefied oxygen. It's estimated that the formation of carbonization conductivity as the currents are easily flowed.

In this study, characteristics of silver ink-jet printing were investigated under various substrate treatments such as substrate heating, hydrophobic coating, and ultraviolet(UV)/ozone soaking. Fluorocarbon(FC) film was spin-coated on the polyimide (PI) film substrate to obtain a hydrophobic surface. Although hydrophobicity of the FC film could reduce the diameter of the printed droplets, the singlet images printed on the FC film surface showed irregularities in the pattern size and the position of the printed droplet along with droplet merging phenomenon. The proposed UV/ozone soaking of the FC film improved the uniformity of the pattern size and the droplet position after printing and substrate heating was very effective way in preventing droplet merging. By heating of the substrate after UV/ozone soaking of the coated FC film, silver conductive lines of 78-116 ${\mu}m$ line were successfully printed at low substrate temperatures of $40^{\circ}C$.

A detailed investigation of cell structure and electrical characteristic in chalcogenide-based phase-change random access memory(PRAM) devices is presented. We used compound of Ge-Se-Te material for phase-change cell. Actually, the performance properties have been improved surprisingly then conventional Ge-Sb-Te. However, crystallization time was as long as ever for amorphization time. We conducted this experiment in order to solve that problem by doping-Sb with annealing.

Microstructure and electrical properties of Ga-doped ZnO (GZO) films grown on $Al_2O_3$ templates by Pulsed Laser Deposition (PLD) are investigated utilizing X-ray diffraction method and Hall measurement, respectively. In order to determine the optimized operating condition of the PLD, statistical design of experiment (DOE) is employed. It provides the systematic and efficient methodology for characterization and modeling of PLD processing with a relatively small number of experiments. The most optimized recipe of the process factors is obtained by response optimizer in Minitab.

In order to form a p-type ZnO thin film, ZnO thin film is deposited by pulsed laser deposition(PLD) on GaAs substrate followed by nermal treatment that ensures the diffusion of As atoms from the GaAs substrate to the ZnO thin films. Photoluminescence (PL) measurement reveals that the improved qualify of ZnO thin films is acquired at the growth temperature of $400^{\circ}C$. It is ZnO film grown at $100^{\circ}C$ that shows the change from n-type to p-type by the thermal treatment. Measured carrier concentration in the film is changed from $-5.70{\times}10^{13}\;to\;9.09{\times}10^{18}$.

We synthesize ZnO nanowires (NWs) doped with 3 wt% Ga on sapphire substrate using a hot-walled pulsed laser deposition (PLD) system named PLD in Furnace. A proprietary target rotating system is employed in the furnace to ensure the homogeneity of the deposition. The kinetic energy of the laser-ablazed ZnO is controlled for the optimization of NW formation. The physical properties of the resultant NWs are presented.

In this study, low temperature sintering property of the $0.6TiTe_3O_8-0.4MgTiO_3$ ceramics with sintering adds were investigated for LTCC application which enable to cofiring with Ag electrode. $TiTe_3O_8$ mixed with $MgTiO_3$ to improve the temperature property. In the X-ray diffraction patterns, the columbite structure of $TiTe_3O_3$ phase and ilmenite structure of $MgTiO_3$ phase were coexisted in all specimens. In the case of $H_3BO_3$ addition, the bulk density and dielectric constant were decreased but quality factor was increased with amount of $H_3BO_3$ additions. The TCRF of the $0.6TiTe_3O_8-0.4MgTiO_3+xwt%H_3BO_3$ ceramics were moved to positive direction. In another case, SnO addition, the bulk density and dielectric constant were increased but Quality factor was decreased with amount of SnO additions. The TCRF of the $0.6TiTe_3O_8-0.4MgTiO_3$+ywt%SnO ceramics were shifted to negative direction. The dielectric constant, quality factor and TCRF of the $0.6TiTe_3O_8-0.4MgTiO_3$ ceramics with $2wt%H_3BO_3$ and 2.5wt%SnO sintered at $830^{\circ}C$ for 1h, were 28.5, 39,570GHz, $+9.34ppm/^{\circ}C$ and 29.86, 35,80000z, $-0.58ppm/^{\circ}C$, respectively.

The $V_2O_5$ thin films deposited on Pt/Ti/$SiO_2$/Si substrates by RF sputtering method exhibited fairly good TCR and dielectric properties. It was found that film crystallinity, dielectric properties, and TCR properties were strongly dependent upon the annealing temperature. The dielectric constants of the $V_2O_5$ thin films annealed at $300^{\circ}C$ were 37.7, with a dielectric loss of 2.535, respectively. Also, the TCR values of the $V_2O_5$ thin films annealed at $300^{\circ}C$ were about -2.65%/K.

TWO-CHANNEL방식의 디지털 광센서는 I2C의 출력을 가지고 있다. 하나의 CMOS집적회로에 포토다이오드와 기존의 아날로그-디지털 변환기(ADC)로 구성되어 있었던 방식과는 달리 2개의 비교기(Comparotor)로 2개의 채널을 형성하게 된다. 인간의 눈과 비슷한 반응을 얻기 위해 16-bit의 유효 범위를 갖는다. 이 광센서는 광원의 넓은 파장에 적합하게 설계 되었다.

In this paper, ZnO thin films were deposited by pulsed laser deposition (PLD) on $Al_2O_3$ (alumina) at room temperature in various $O_2$ ambient. Rapid thermal annealing (RTA) has been performed at temperatures from $400^{\circ}C$ to $700^{\circ}C$. The effects of temperature and ambient on the structural property of ZnO films were examined by x-ray diffractometer (XRD) and atomic force microscopy (AFM), respectively. The results show that the (002)-oriented ZnO thin films on non-single crystal alumina were obtained in over 30mTorr ambient at all RTA temperatures including room temperature. The foil-width half maximum (FWHM) of (002) peak decreases as the RTA temperature increases, which indicates that ZnO thin films with RTA have improved crystalline quality.

Many extensive researches in the area of sensor's technology for durability assessment in concrete structures have increasingly been carried out in recent years. In this paper, the principles and use of various sensors involved in the health monitoring of concrete structures are described.

The composites were fabricated $\beta$-SiC and $TiB_2$ powders with the liquid forming additives of 8, 12, 16[wt%] $Al_2O_3+Y_2O_3$ as a sintering aid by pressureless annealing at $1,650[^{\circ}C]$ for 4 hours. Reactions between SiC and transition metal $TiB_2$ were not observed in the microstructure and the phase analysis of the pressureless annealed SiC-$TiB_2$ electroconductive ceramic composites. The relative density, the flexural strength, the Young's modulus and the Vicker's hardness showed the highest value of 82.29[%], 189.5[MPa], 54.60 [GPa] and 2.84[GPa] for SiC-$TiB_2$ composites added with 16[wt%] $Al_2O_3+Y_2O_3$ additives at room temperature. The relative density of SiC-$TiB_2$ composites was lowered due to gaseous products of the result of reaction between SiC and $Al_2O_3+Y_2O_3$. The electrical resistivity showed the lowest value of 0.012[${\Omega}{\cdot}cm$] for 16[wt%] at 25[$^{\circ}C$]. The electrical resistivity was all negative temperature coefficient resistance (NTCR) in the temperature ranges from 25[$^{\circ}C$] to 700[$^{\circ}C$].

In this study, the fabrication technique of a plannar field emission structure with DLC were studied Electric properties of carbon film on silicon substrate in methanol solution was carried out with various current density, solution temperature and electrode spacing between anode and cathode. The DLC film deposited on the Si substrate, plannar $SiO_2$ was obtained due to the shape of bottom electrode.

Electrochemical method of carbon film on silicon substrate in methanol solution was carried out with various current density, solution temperature and electrode spacing between anode and cathode. The carbon films with smooth surface morphology and high electrical resistance were formed when the distance between electrode was relatively wider. The electrical resistance of the carbon films were independent of both current density and solution temperature.

This study investigates the performances of the signaling techniques including differential signals for the power-distribution network(PDN)s with and without the slit, using a rigorous evaluation method, validated by the FDTD simulation up to 5 GHz.

$In_xGa_{1-x}N/In_yGa_{1-y}N$ 다중 양자우물 녹색 발광 다이오드에 2차원 광자 결정을 이용하여 음극선 발광의 향상을 관찰 하였다. 정사각형 배열의 2차원 광자 결정의 주기와 격자 상수는 200/500 nm 이고 전자빔 리소그래피로 광자결정 패턴을 제작한 후, 플라즈마 건식 식각법으로 패턴을 구현하였다. 식각 시간의 차이를 둔 구현된 패턴의 홀 깊이는, 각각 ${\sim}69nm,\;{\sim}99nm,\;{\sim}173nm$ 이었다. 전계 방사 주사 현미경 측정 결과, 형성된 홀은 끝이 잘린 역전된 원뿔 모양으로 식각 되었다. 식각 된 홀의 깊이에 따라 광자 결정이 있는 부분이 없는 부분보다 최대 ${\sim}30$배 많은 광자가 검출 됨을 확인하였다.

Two-dimensional photonic crystal structures have been fabricated on the chalcogenide material using holography lithography out of many production technical. The fabricated lattice can be observed obliquely by measuring diffraction pattern. The diffraction pattern of the microstructure has been observed with a He-Ne laser beam at wavelength of 632.8 nm. The diffracted beam has been analyzed by using the diffraction efficiency measurement method.

The emission of external incident field or near device field is important factor of EMI and EMC. In this paper, we apply MOM, using the RWG basis function, to analysis the induced current distribution on the PEC and dielectric plates. The volume and surface integral equations are presented for the electromagnetic wave scattering from plate structures composed of dielectric and conducting objects.

The use of conventional Twyman and Fizeau interferometers inevitably fails in testing high precision optics because of errors always existing in reference elements producing the reference wavefront. Therefore it is necessary to apply to this task the interferometers of a radically new type, which are able to produce perfect reference wavefront with the help of light diffraction by a small obstacle or pinhole. In this paper new theoretical approaches and schematics of point diffraction interferometers are considered in detail with paying attention to constructive reliability. Such interferometers do not use reference optical surfaces and readily provide adequate estimation of errors and aberrations value of 0.01 wavelengths.

본 연구에서는 고분해능 및 고감도화된 시스템 개발을 위하여 AOTF를 이용하여 하이퍼스펙트럼 영상기법을 활용한 전임상 영상장비에 대한 연구를 수행하였다. 제작된 고감도 하이퍼스펙트럼 분자영상 시스템의 생물학적 적용을 위하여, AOTF의 파장 또는 진동수를 변화시키면서 GFP가 발현된 HEK 293 세포의 이미지를 촬영하였다. 또한, 제작된 실험 대상물 이미지화 시스템을 이용해서 실험용 쥐의 이미지를 촬영하였다. 실험용 쥐를 크세논 아크램프 사용 전 후 이미지를 촬영한 결과 크세논 아크 램프 사용 후에는 청색의 선명한 영상을 얻을 수 있었다.

나노미터 크기의 동심원 패턴이 형성된 도광판을 설계하기 위한 전산모사를 수행한다. 광원은 LED 1개를 사용하였으며 PMMA 도광판 재질의 파장에 따른 빛의 흡수 현상을 고려하였다. 도광판 위치에 따른 투과광선의 세기 분포, 투과광선의 투과각도 분포 및 편광에 따라 투과광선의 세기가 어떻게 달라지는지 살펴보았다.

본 논문은 LabVIEW를 이용하여 온도측정과 amperometry 측정을 동시에 하며, amperometry 측정오차와 구동전압의 세팅 시간을 줄일 수 있는 시스템을 설계한 내용을 담고 있다. Amperometry는 구동전압을 인가하여, 전류를 측정하는 방법인데, 정확한 측정을 위해서는 구동전압을 균일하게 인가해야 한다. 또한 바이오 분야에서의 amperometry 측정은 온도에 따라 측정 결과가 다르게 나타날 수 있기 때문에 온도의 측정과 amperometry 측정이 동시에 이루어져야 측정오차를 줄일 수 있다. 본 논문에서는 이상(異常) 구동전압의 배제 알고리즘을 통하여 전류측정의 오차를 ${\pm}$70pA에서 ${\pm}$50pA이내로 줄였으며, proportional control을 응용한 알고리즘을 사용하여 307초의 측정시간을 105초로 단축하였다. 또한 amperometry 측정 과정에서 온도를 실시간으로 측정함으로써 측정상태를 보다 정확히 파악하는 시스템을 구성하였다.

We present full 3-D simulation of dielectrophoretic (DEP) deflection of particle trajectory in micro channel and compare the simulation results with experimental results. In simulation, the particle 3-D movements along x, y and z-axis are simulated precisely, and the streamlines of particles movements and the change of particle height are investigated experimentally. Therefore, the deflection performance is investigated on the designed and fabricated deflection microchip.

We present the design and fabrication prcoess of a two-axis tilting micromirror device driven by the electrostatic vertical comb actuator. A high aspect-ratio comb actuator is fabricated by multiple DRIE process in order to achieve large scan angle. The proposed fabrication process enables a mirror to be fabricated on the wafer-scale. By bonding a double-side polished (DSP) wafer and a silicon-on-insulator (SOI) wafer together, all actuators on the wafer are completely hidden under the reflectors. Nickel lines are embedded on a Pyrex wafer for the electrical access to numerous electrodes of mirrors. An anodic bonding step is implemented to contact electrical lines with ail electrodes on the wafer at a time. The mechanical angle of a fabricated mirror has been measured to be 1.9 degree and 1.6 degree, respectively, in the two orthogonal axes under driving voltages of 100 V. Also, a $8{\times}8$ array of micromirrors with high fill-factor of 70 % is fabricated by the same fabrication process.

We present an one-axis parallel-plate type of bulk micromachined torsional micromirror array with single crystalline silicon (SCS) fabricated on the glass substrate. Structurally, bottom electrodes (amophous silicon) in this mirror are DRIEed along the aluminum mirror patterns on SCS, which are self-aligned with mirror plates. Tracing the history of the micromirror study, we found that few papers have been published on research for uniform driving voltages based upon the tilting direction. If there is a slight misalignment during anodic bonding between top (mirror plate) and bottom electrodes, the non-uniformity of driving voltage will be led depending on two different tilting direction. This paper discusses how much the pull-in voltages can be different due to misalignment between two electrodes. Moreover, We achieve uniform pull-in voltage regardless of misalignments in photolithography and anodic-bonding between two individual layers.

This paper describes a resonant driving piezoelectric micro cantilever practicable to ultrasound thrombolysis device for the treatment of ischemic stroke. The proposed piezoelectric cantilever was designed to be a unimorph structure of Si/$SiO_2$/Ti/Pt/PZT/Pt, and fabricated by top-down sequence etching process. The red blood cell (RBC) lysis experiment was carried out to confirm the usability of the proposed cantilever. Total 87.76 % of RBCs were ruptured using the ultrasound generated by up-down actuations of the fabricated cantilever with AC voltage having the frequency of 19.36 Hz and the magnitude of $30V_{p-p}$.

This paper describes frequency response of two-mass system for gyroscope applications. The two-mass system of the proposed device is adapted to the sensing part of the gyroscope in this research. Two-mass system has two resonant peaks and wide flat region between two resonant peaks. The resonant frequency of driving part is in this flat region. Therefore, frequency tuning is not necessary for mode matching. In the proposed device, resonant frequency is designed as 7183 Hz in driving part. Mass ratio of two masses in sensing part is 0.1 and device size is 6 mm $\times$ 6 mm. The device is fabricated by SiOG process. The fabricated spring width is increased from $4{\mu}m$ to $4.5{\sim}4.7{\mu}m$, and the measured resonant frequency is 8392 Hz in driving mode. We operated the sensing part using parallel plate of proof mass to verify the sensing part. It is confirmed the device has a wide fiat region in frequency response curve and the resonant frequency of the driving part is in the wide flat region of sensing mode.

나노임프린팅 기술을 이용하여 원기둥형 나노 패턴을 갖는 도광판을 제작하였다. 나노 임프린트 공정을 이용하기 위해서는 니켈 스탬퍼가 필요하기 때문에 이를 제작하기 위하여 실리콘 웨이퍼 상에 건식식각을 이용하여 실리콘 몰드를 제작하였다. 제작된 실리콘 몰드를 전주도금을 이용하여 니켈 스탬퍼를 제작하였다. 제작된 니켈 스탬퍼를 사용한 나노임프린트 공정을 통해 원기둥 나노패턴을 갖는 도광판을 제작하였다.

This paper is analyzed the internal type UHF sensors that be able to monitor the condition of the distribution facilities and the location selecting of that sensors. It set the PD cell on the inside of 22.9kV load switchgear and then it executed Partial Discharge test. it introduced the result of the test.

In this study, we developed intelligent spacer built in the internal type UHF PD sensors. 3-Dimensional electro-magnetic simulations were performed to analyze electric-field distribution of the single-phase GIS and three-phase GIS. After considering the spacer's specification, Sensor structures were designed and analyzed using the 3-D EM Simulator. As a result of the simulation the internal type UHF PD sensors were built in. Performance of the sensor built into real scale GIS spacer was measured in terms of return loss and detected Max voltage. And we identified a character of the intelligent spacer by using 5pC partial discharge ceil.

In these days $SF_6$ mixtures and alternative gas have been studied because of global warming and liquefying at low temperature and high pressure. At present work the breakdown characteristics of $SF_6/CF_4$ mixture in non-uniform field was performed. The experiments were carried out under positive and negative standard lightning impulse (SLT) voltages. The point-plane electrode was used with 3 mm gap distance in the test chamber. The $SF_6/CF_4$ mixture which contain 20% of $SF_6$ was compared with pure $SF_6$ and $CF_4$ gas. Experimental gas pressure ranged from 0.1 to 0.4 MPa. The breakdown voltage under negative SLI is higher than the breakdown voltage under positive voltage. And the breakdown voltage of $SF_6$ 20%, $CF_4$ 80% mixture is similar to that of pure $SF_6$.

PDP cell에서 발생한 가시광선의 분포를 visible ray trace 방법을 이용하여 계산하였다. 본 논문에서는 ITO-less 구조를 시뮬레이션 하여 가시광선의 출구 효율, illuminance 분포, luminance 분포를 구하였다.

PDP는 LCD, OLED등과 같은 FPD(Flat Panel Display)들과는 차별화된 우수성을 가지고 있다. 따라서 본 논문에서는 AC-PDP에서의 MgO박막의 material property를 향상시키기 위하여 MgO pellet에 미소량의 Ca를 첨가하였으며 이에 따른 MgO박막을 통해 Ca의 첨가에 따른 효과를 분석하였다. MgO박막은 e-beam evaporation 방법을 사용하였으며 4인치 테스트 패널을 만들어서 방전개시전압, 방전유지전압, 어드레싱지터를 측정하였으며 방전효율은 Ca가 0.025%, 0.035%, 0.042%가 첨가 되었을 때 각각 비교하였으며, 0.035%가 첨가 되었을 때가 가장 좋은 효율을 가진다.

PDP의 luminous efficacy의 향상을 위해서는 동작가스의 연구가 매우 중요하다. 본 논문에서는 bolsig simulator를 사용하여 여러 비율의 Xe+Kr+Ne 3원가스 시뮬레이션을 통하여 각 가스입자들에 전달되는 이온화에너지, 여기에너지를 조사하였다. 실험에서 short discharge gap과 long discharge gap을 가진 7인치 테스트 패널 2개를 사용하여 가스압력과 Xe+Kr+Ne 혼합비를 변화시켜가며 discharge voltage, luminance, luminous efficacy를 측정하여, 방전특성을 연구하였다.

본 논문에서는 scan 전극과 common 전극 사이에 보조 전극을 가진 PDP에서 asymmetry, long gap mode 와 같은 새로운 구동방법을 제안한다. asymmetry mode에서 주전극의 가운데 부분에 위치한 보조전극은 리셋, 어드레스, 서스테인의 모든 구간동안 scan 또는 common 전극에 연결되어 있다. long gap mode에서는 전기적으로 끊어져있거나 초기 몇 개의 서스테인 펄스를 제외하고 서스테인 구간동안 Vs/2의 전압으로 유지된다. 제안된 조와 구동 방법에서 전력에너지소비를 최소화함으로써 더 높은 발광효율을 얻을 수 있다. 새로운 구동방법의 효용은 다양한 Xe분압상태에서도 연구되었다.

본 연구에서는 기존의 ITO전극을 사용하지 않는 새로운 전극구조를 가지는 AC-PDP를 제안하였다. 제안한 구조는 상판의 유지전극들을 패터닝된 유전체층 사이에 Ag 전극을 경사형 으로 형성하여 만든 구조이다. 테스트 패널은 각각 $250{\mu}\;300{\mu}m,\;350{\mu}m$의 유지전극 간격들을 가지는 제안된 구조와 기존의 유지전극 간격 $60{\mu}m$의 ITO 구조를 reference로하여 제작하였다. 제안한 구조의 휘도는 방전 갭의 길이에 비례하여 증가하였고 방전전류가 약 $33{\sim}70%$ 감소하여 효율이 유지전극 간격 $300{\mu}m$에서 최대 130% 증가하여 2배이상 증가하였다.

기존의 fence전극구조는 ITO구조에 비해 휘도가 감소하여 효율이 떨어지는 것으로 알려져 있다. 따라서 효율 상승을 위하여 다음과 같은 fence 구조를 제안하였다. 실험은 reference(II-fence형 전극구조)와 제안된 구조(II-fence형 돌기격벽측배치)로 구성되어있는 4-inch AC-PDP 패널을 직접 제작하여 discharge current, luminance, luminous efficiency를 측정하여 비교하였다. 제안된 구조의 휘도는 약 5% 감소하였으나, 방전전류가 최대 14% 감소하였고, 효율면에서 최대 12%의 효율 상승을 가진다.

현재 초고압 송변전기기에 적용되고 있는 $SF_6$가스는 절연 및 소호성능이 우수하며 회복특성이 뛰어나기 때문에 초고압 기기의 절연매체로서 널리 사용되고 있으나 가격이 비싸고 저온 및 높은 압력에서 액화되기 쉬우며 대기 중으로 방출될 경우에는 온실효과를 야기 시키는 단점을 가지고 있다. 최근 환경에 대한 관심과 규제가 높아지면서 온실가스에 대한 규제로서 교토 의정서가 정식 발효됨에 따라 $SF_6$가스는 금후 총량 제한에 의해 사용량이 규제 받을 가능성이 대단히 높다. 따라서 $SF_6$ 가스와 Air, N2, CO2, N2/O2 합성가스, He 등과 혼합된 절연매체들이 하나의 대안으로 연구되었다. 본 연구에서는 대체 절연가스로 주목받고 있는 Dry-air(공기 중에서 수분과 각종 불순물을 제거한 공기), N2/O2 합성가스, N2 가스를 4mm 간격의 준평등(구대구전극) 전계에서 0.5atm에서 9atm까지 변화시켰을 때 절연내력을 비교하였다. 또한, 보다 평등전계에 가까운 10mm의 간격에서도 0atm에서 4atm까지 동일한 전압을 인가하여 절연내력을 비교 분석하였다.

Recently, diverse techniques for diagnosis on power equipments of the live wire conditions are developed. These techniques are very important that find out the fault signs in power equipments. This paper is Compared with Ultra-Violet and Ultra-Sonic Generated by an Insulator at 22.9kV. The volume of UV images are increased by the square of the applied voltage. The output signals of ultrasonic are detected at about 20kV to 30kV. Hereafter, through the continuous DAQ and analysis, these techniques are the effective method for the improvement of the exciting diagnosis.

90년대 후반 부터의 초고압 XLPE 케이블 시스템의 연구개발 및 납품 성과에 힘입어 국내 업계 최초로 2006년 미국시에 345kV 광복합 XLPE 케이블 시스템을 수주하였다. 본 논문은 미국 뉴욕주 최대 전력시스템 운용 회사인 KeySpan사가 발주하여 LS전선이 Turn-Key 방식으로 수주, 뉴욕주 롱아일랜드에 성공적으로 준공하여 운전 중인 345kV XLPE 광복합 케이블 시스템 project에 대하여 기술하고 있다.

반합성지 절연 전력케이블 시스템은 유전체 손실을 줄이고 절연두께 저감할 수 있으며 경제성면에서도 유리하다는 장점 때문에 많은 사용검토가 이루어져 왔다. 본 논문은 최근 LS전선이 국내 최초로 개발한 400kV급 초고압 반합성지 전력케이블의 반합성지 설계, 케이블 및 접속함 개발, 그리고 인증 Type Test 및 장시간 실증시험등 주요 개발과정을 기술하였다. OF 전력케이블의 오랜 경험과 다양한 연구결과를 바탕으로 반합성지 전력케이블 시스템을 단기 내에 개발하여 전력 케이블 및 접속함에 대하여 국제공인기관인 KEMA로부터 IEC 60141-1에 따른 인증서를 획득하였고, 장시간 실증시험에 성공적으로 완료함으로써 반합성지 절연 전력케이블 시스템 전체의 신뢰성을 확인할 수 있었다.

Axial magnetic field was applied into the hollow anode of plasma torch for the purpose of extension of electrode lifetime. The average arc voltage increased because the arc column became longer, the arc voltage ripple frequency became low. The steady state of arc voltage was removed by applied magnetic filed. The lifetime of electrode was over 1000 hours which is 100 times longer than operation without magnetic field.

Focused shock wave generation was tested under the water by the method of wire explosion. The wire was installed a focal point of the half ellipsoid, and the shock wave was focused on the other focal point. A numerous cavitations were observed in the path of the traveling shock wave and focal point by using high speed camera.

A hollow cathode which has extremely stable discharge characteristic has been developed. This is composed of the two separated lanthanum hexaboride ($LaB_6$) of a disk type in the tube as the electron emitters. The way of design is of great advantage to extend the surface discharge area of the $LaB_6$, which is also useful for optimal fixing of the $LaB_6$. The hollow cathode is capable of producing 30 kW (100 V, 300 A) of power continuously.

$SF_6$ gas used widely as insulating component in electric power industry has excellent in insulation and arc extinguishing performance in gas-insulated switchgear. However, the concern about eco-friendly alternative gas is currently rising because $SF_6$ gas is one of the main greenhouse gases. In this paper, dry-air and composite-insulation (dry-air+epoxy) as the alternative technology for $SF_6$ gas insulation is studied. Under the gas pressure ranged from 0.1 to 0.6MPa, the breakdown voltage of dry-air were measured in AC electric field. The data of composite-insulation were acquired by changing the thickness of epoxy used in each composite-insulation under the same condition.

송배전용 설비에 사용되는 옥외 절연물로는 porcelain이나 glass insulator가 주로 사용되어 왔지만 최근 신소재의 발달로 가볍고 절연성능이 우수한 폴리머애자(composite insulator)가 보편화되기 시작하였다. 고분자 소재를 이용한 대형절연물의 제조 기술이 성숙되어 가고 있고, 생산 원가 면에서도 porcelain보다 유리하여 이미 폴리머애자의 가격이 저렴해지고 있는 실정이다. 더욱이 국토가 좁아 송배전 설비의 시설환경이 좋지 않고(산악, 도서) 선진사회화 되면서 인건비 상승으로 인하여 취급이 용이하고 경량인 이들 폴리머애자의 장정이 부각되는 시점에 와 있다. 본 논문은 철탑에서 도체를 지지하고 있는 기존의 무거운 금속 암과 애자련 대신 전기적 특성과 내환경성이 우수한 암 절연물을 사용한 154kV급 철탑 설계 방법과 컴팩트화에 대한 방법을 제시하고자 한다.

The Cable Transit has an adaptable center hole for accommodating a cable to be passed through the wall(bulkhead/deck). The Cable Transits Sealing System must have important character which seal and protect against fire, smoke, gas, water, etc and consist of natal frame, sealing system and the cable, insulation. In this paper, introduced our cable transit organic expansion sealing material system, fire-resistance test and test result, etc. We carry to fire-resistance test in according to FTP Code Part 3(IMO Res. A. 754(18)) for A-60 class cable transit and the test result for our cable transit sealing system was satisfied.

Tilting train has been developed to increase the operational speed of the trains on conventional lines which have many curves. This train are tilted at curves to compensate for unbalanced carbody centrifugal acceleration to a greater extent than compensation produced by the track cant, so that passengers do not feel centrifugal acceleration and thus trains can run at higher speed at curves. This paper show that results of normal capacity calculations of the electrical equipments such as Main transformer, PWM converter, VVVF inverter, traction motor in TTX(tilting train express) with maximum operation speed 180 km/h.

Induction Motor is important at tilting train. Tiling train induction motor should be operated to commercial servicespeed 180km/h at Korea Conventional Line upgrade railroad. As the induction motors are without commutators, maintenance is easy and it is far lighter than the conventional motors with the same capacity. The induction motor, however, posed problems in use as its motor torque is not large enough compared with DC motors. With the recent advances in power semiconductors, it is possible to apply the induction motors to trains by applying VVVF inverter control method to the traction motor. In this study, we realize the stable measurement AC motor temperature characteristic of TTX train.

We have developed a new measurement system by using GPS to complement those errors. In general, GPS receivers are composed of an antenna, tuned to the frequencies transmitted by the satellites, receiver-processors, and a highly-stable clock. The GPS mounted on the roof of TT4 in KHST receives a signal from the RS232 communication port, and it is connected to the network system in TT3 after converting with TCPIP communication. It is able to track the position of vehicle and synchronize the signal from different measurement system simultaneously. Therefore it is able to chase the fault occurrence, track inspection and electrical interruptionat real-time situation more accurately. There is not an error coursed by vehicle conditions such as slip and the slide.

We developed a measurement system for on-line test and evaluation of performances of KHST. The measurement system is composed of software part and hardware part. Perfect interface between multi-users is possible. A new method to measure temperature was applied to the measurement system. By using the system, fault diagnosis and performance evaluation of electric equipment in Korean High Speed Train was conducted during test running.

The measurement system is composed of the industrial computers installed in the console and the measurement racks mounted on each car. It is utilized to accumulate the data by the communication card and the optical cable. The optical cable and power cable are coupled at the connector located in joint of train to make easy to disconnect car each other. The signal conditioner is designed to choose and to extend the channel for each sensor readily, In this study, the programs for measurement and analysis were also developed to understand the traction system characteristics of TTX. Using this measurement system, we studied that acceleration test, re-powering test and gradually powering test. From the test results, we saw the performances of the traction systems are normal.

Once high current flows through the vacuum interrupter, eddy current occurs due to the time-varying axial magnetic field caused by the current(AC) and it causes a decrease in axial magnetic field generated by current flowing through coil electrode. but if there are slots on contact electrode it is possible to increase the amplitude of axial magnetic field by reducing the influence of eddy current. there has been many studies about the number of slot of the contact electrode[1][2][3]. In this paper, in addition to these previous results we deal with the influence of the length and width of the slots on axial magnetic field at the mid-gap plane in 4 segment coil type vacuum interrupter by using 3D finite element method software.

In case of a line-to-ground fault at transmission lines, a portion of fault current will flow into the earth through the footings of the faulted tower causing electrical potential rise nearby the faulted tower footings. In this situation, any buried pipelines or structures nearby the faulted tower can be exposed to the electrical stress by earth potential rise. Although many research works has been conducted on this phenomena, there has been no clear answer of the required separation distance between tower footings and neary buried pipeline because of its dependancy on the soil electrical charactersics of the concerned area and the faulted system. In this paper, an analytical formula to calculate the requried sepeartion distance from the faulted tower has been derived.

Unstable sustain discharges can occur at the bottom cells of the panel at high temperature. To solve this phenomenon, the wall charge variation during an address period was investigated. A test panel of 7.5 inch XGA level was used and one green cell was measured. In order to realize operating condition equal to that of the bottom cells of 50 inch panel, the addressing stress pulses are applied. It seems that the resultant wall charge loss during address period increased with increase of temperature as well as the addressing stress pulse voltage. Therefore it results in unstable discharge during sustain period.

This paper represents the reliability assessment on the mould type combined transformer used in the distribution system by electrical tests. For the reliability assessment, we had tested lightning impulse test, short-circuit withstand capability test, electrical accelerated life test and so on to the mould type combined transformer of Young-Hwa Industrial Electric Co., Ltd.

This paper researched permittivity of carbon nanotube reinforced semiconductive shield materials for power cable in accordance with carbon nanotube content. Permittivity measured 1[Hz], 1[kHz], 1[Mhz] in frequency range, and range of temperature measured to 100$[^{\circ}C]$ from -50$[^{\circ}C]$. It is stable to 100$[^{\circ}C]$ from -50$[^{\circ}C]$ without different gap. But, in case of CNT:CB=100:0, permittivity decreased by temperature increment. Also, in case of CNT:CB=100:0, it shows highest permittivity. Permittivity of change have little no the power of influence by frequency, but in case of 1[Mhz], CNT:CB=100:0 of specimen decreased more than other frequency. This influence thinks phenomenon of induced electricity dispersion.

Micro plasma has been recently studied to investigate the effects on various cells. We study a micro-plasma produced by a plasma needle that is operated with RF power and its effects on G361 melanoma cells. The micro plasma size ranges from sub-mm to several mm at a few watts of RF power. For the bio-medical treatment, low-temperature plasma is obtained and gas temperature is controlled within several tens of degrees $(^{\circ}C)$ in order not to disturb cell activities. Elementary spectroscopic studies to obtain plasma characteristics are presented for Ar and He plasma with different frequencies of RF power. Also the preliminary results of the micro plasma effects on G361 melanoma cells are presented. It was observed that the irradiation of micro plasma induces cell death through the deprivation of tyrosine phosphorylation in the G361 cells.

In 6.6kV Rotary Machine Stator Windings, Corona Discharge, Discharge at Conductor Surface, Slot Discharge and Endwinding Discharge is happended by electronic degradation. Also, if Partial Discharge cause in inner-part of Rotary Machine Stator Windings, it will be happended voltage and current pulse. In case of discharge spark, RF electromagnetic wave, which tranmits at discharge position, can happen. To detect this kind of RF electromagnetic wave efficiently, we have designed Planar Antenna Sensor with the CST MWS simulation program. Also we have confined the application possibility, which can analize the partial discharge in Rotary Machine Stator Windings. In the Future, sample of planar antenna sensor will be able to compare with the data of simulation by CST MWS program.

This paper is to be linked the discharge theory with parameter t the coefficient of restitution used in physics. The collisions is of particular importance in high voltage engineering, nuclear, and high-energy physics. Here the bodies collided may be atoms, nuclei or various elementary particles, such as electrons, protons, and so on.

유도결합 플라즈마(ICP)에서 안테나의 특정부분에 유도자기장을 보강 또는 상쇄 시키는 형태의 두 안테나를 고안하였다. 플라즈마 밀도와 전자온도, 플라즈마 전위, 전자에너지 분포함수 등의 플라즈마 파라미터들로 그 특성을 비교하였다.

본 논문은 1310nm 단일모드 광섬유를 이용하여 온도센서로 활용하기 위한 연구이다. 기존광섬유센서의 연구는 복잡한 여러 가지 기기를 이용하여 구성된 시스템이었다. 그리고 산란 변화를 주기 위하여 Bragg 격자나 Pulse generator를 이용하여 광주파수의 변화를 측정하거나, YAG 레이저를 이용 벌크형 시스템을 택하여 구성하였는데 실험 환경을 구성하는 어려움과 측정된 데이터의 정확도에 대한 문제점이 있었다. 본 연구에서 제안한 유도 브릴루앙 산란(sBs: stimulated Brillouin scattering)광을 이용한 온도센서 시스템은 기존의 측정방식 보다 간소화된 직렬방식의 시스템이다. 광주파수에서 발생하는 노이즈와 애매한 결과에 대해서 신뢰성과 정확도를 확보하기 위하여 지능형인 뉴로-퍼지 알고리즘을 이용하여 분석함으로써 기존 시스템 보다 정확한 데이터를 얻고자 하였다. 본 연구에서 sBs는 빛의 산란 특성 중 광주파수가 온도에 변화에 대해 각각의 온도 변화당 천이가 이루어졌음을 측정하였다. 시스템에서 출력된 데이터를 뉴로-퍼지로 분석한 변화율은 1.1MHz/의 결과를 얻었다.

The RF inductive discharge of inductively couples plasma (ICP) continues to attract growing attention as an effective plasma source in many industrial applications, the best known of which are plasma processing and lighting technology. Although most practical ICPs operate at 13.56 [MHz] and 2.65 [MHz], the trend to reduce the operating frequency is clearly recognizable from recent ICP developments. in and electrodeless fluorescent lamp, the use of a lower operating frequency simplifies and reduces cost of RF matching systems and RF generators and can eliminate capacitive coupling between the inductor coil and plasma, which could be a strong factor in wall erosion and plasma contamination. In this study, electric and optical characteristics of electrodeless fluorescent lamp by changing ferrite position is discussed.

In recent, there have been several developments in lamp technology that promise savings in electrical power consumption and improved quality of the lighting space. Above ail, the advantage of ring-shaped electrodeless fluorescent lamp is the removal of internal electrodes and heating filaments that are a light-limiting factor of conventional fluorescent lamps. Therefore, the life time of ring-shaped electrodeless fluorescent lamps is substantially higher than that of conventional fluorescent lamps and last up to 60,000 hours and is intended as a high efficacy replacement for the incandescent reflector lamp in many applications. In this paper, when appling the electrodeless lamp in luminaire, We analyzed change of optical and electrical characteristics.

나노미터 크기의 회절격자 패턴이 형성된 도광판을 설계하기 위한 전산모사를 수행한다. 광원은 LED 4개를 사용하였으며 PMMA 도광판 재질의 파장에 따른 빛의 흡수 현상을 고려하였다. 도광판 위치에 따른 투과광선의 세기 분포, 투과광선의 투과각도 분포 및 편광에 따라 투과광선의 세기가 어떻게 달라지는지 살펴보았다.