Fuel cell is remarkable for one of the clean energy recently. But in the fuel cell case, it has characteristics with low voltage and high current. Therefore, for using domestic power, it should be changed to the power source with commercial voltage and frequency. In this paper fuel cell simulator having electrical characteristics is designed and constructed instead of fuel cell stack. Voltage generated from fuel cell is from 39V to 72V dc and should be boosted to 400V dc for home appliances. A stand alone system including the inverter and DC/DC converter for the fuel cell is then proposed. Simulation result is used to support the analysis.

본 논문은 펄스 삽입 보조 회로를 갖고 있는 12-펄스 브리지 4대를 사용한 36-펄스 back-to-back 전압원 컨버터를 제안한다. 제안된 back-to-back 접압원 컨버터는 교류 연계점에서 유효전력과 무효전력의 독립적인 제어가 가능하다. 펄스 수를 증가하는 원리는 이론적 접근을 사용하여 분석되었다. 제안된 시스템의 동작 타당성은 PSCAD/EMTDC 소프트웨어의 시뮬레이션을 통해 검증되었다. 제안된 back-to-back 전압원 컨버터는 HVDC와 FACTS 장치로 널리 사용될 수 있다.

Organic EL has been expected to adopt to a new styles of technology that make flat display after Tang & Vanslyke made good electric luminescence device in late 1980s. Their studies based on multi layer structure that consists of emitting layer and carrier transporting layer using proper organic material. In this study, we made multi layer device using $Eu(TTA)_3(phen)$ as a luminescence material by PVD and investigate luminous properties of each device. But oxidization of organic layer by ITO, energy walls in both pole interface, contaminations of ITO surface, importance of protecting membrane, diffusive dimming of light to cathode organic layer, these causes of degradations are common facts of a macromolecule and micromolecule. We think these degradation caused by the impact of heat and electro-chemical factor, bulk effect and interface phenomenon, and raise a question.

본 논문에서는 전압원 컨버터를 이용한 HVDC 시스템의 제어기를 설계하고 그 동특성을 분석한 내용에 대해 기술하고 있다. 현재 전압형 HVDC의 기술은 전압원 컨버터를 이용하여 최대 330MW까지의 전력을 전송할 수가 있다. 따라서 전압형 HVDC의 시뮬레이션 모델을 통하여 송전계통에 적용시 계통의 전력조류제어 특성을 시뮬레이션 한다. 전압형 HVDC는 기존의 전류형 HVDC와는 달리 유효전력과 무효전력을 독립적으로 제어하는 것이 가능하고 스위칭 주파수가 높기 때문에 수동필터규모가 작아져서 설치면적이 감소한다. 또한 다중터미널 방식을 적용함으로써 전송전력의 유연성을 높일 수 있다.

Using quantitative simulations of weakly ionized plasma, we can analyze gas characteristic. In this paper, the electron transport characteristic in $CH_4$ has been analysed over the E/N range 0.1${\sim}$ 300(Td), at the 300($_{\circ}$ K) by the two term approximation Boltzmann equation method and Monte Carlo Simulation. The electron energy distribution function has been analysed in $CH_4$ at E/N=10, 100 for a case of the equilibrium region in the mean energy. The result of Boltzmann equation and Monte Carlo Simulation has been compared with experimental data by Ohmori, $Lucas^{[18]}$ and Carter. The swarm parameter from the swarm study are expected to sever as a critical test of current theories of low energy scattering by atoms and molecules.

This paper describes experimental analysis of UPQC, which is composed of cascaded H-bridges and single-phase multi-winding transformers. The operational characteristic was analyzed through experimental works with a scaled model, and simulations with PSCAD/EMTDC. The UPQC proposed in this paper can be directly connected to the distribution line without series injection transformers. It has flexibility to expand the operation voltage by increasing the number of H-bridge modules. The analysis results can be utilized to design the actual UPQC system applicable for the actual distribution system.

This paper describes the electron transport characteristics in SiH4 has been analysed over the E/N range 0.5${\sim}$300[Td] and Pressure value 0.5, 1, 2.5 [Torr] by a two-term approximation Boltzmann equation method and by a Monte Carlo simulation. The motion has been calculated to give swarm parameters for the electron drift velocity, diffusion coefficient, electron ionization, mean energy and the electron energy distribution function. The electron energy distribution function has been analysed in $SiH_4$ at E/N=30, 50[Td] for a case of the equilibrium region in the mean electron energy and respective set of electron collision cross sections. The results of Boltzmann equation and Monte carlo simulation have been compared with experimental data by Pollock, Ohmori, cottrell and Walker.

To comparative analysis of proposed techniques, the paper constructs power system model including power transformer, utilizing the EMTP, and collects data through simulation of various internal faults and magnetizing inrush.

3상 4선식 배전방식은 우리나라 저압 수용가에 널리 채용되고 있다. 단상과 3상을 혼합하여 사용하는 경우가 많아 전압불평형에 의한 여러 가지 문제를 발생하고 있다. 3상 4선식 배전시스템에서 3상 동력용으로 단독사용일 경우에는 별로 문제가 되지 않지만, 단상부하와 3상 부하를 혼용사용할 경우에는 부하의 불평형에 의한 어떤 문제를 발생하는지에 대해 저항성 및 유도성 부하를 대상으로 전압불평형율을 측정하고 분석하였다.

The main purpose of this study is to prepare an outline for developing of the module-type text-book system on the customize curriculum management and Contents Systems that achieve self-study systems to make the students adopt themselves into new study atmosphere and maximize the result of study on Osan college in Electric-Electronic field. Questionnaire posed to analyze the demand of teaching materials to the students, and professors and also to find characteristics of students in Osan college. The SPSSWIN/PC+ statistics package was used to assay the collected answers. And simple frequency with percentage, average, and standard deviation were calculated to check the entire trend and actual state of teaching. Therefore, the improvement of the existing teaching materials was demanded while the fundamental ability to study of general students is declining. Consequently, it is necessary to introduce new teaching materials which are simple, easy, and organized to offer the students study desire and interest.

사무소용 빌딩과 같은 전력다소비 건물에서는 전력의 효율적 이용에 의한 에너지절감을 위해서 설계 단계부터 합리적인 전기설비 설계가 요청되고 있다. 본 연구에서는 사무소용 빌딩을 중심으로 일본과 우리나라에 있어서 일반전등전열부하 및 일반동력부하의 전력 소비특성을 조사 분석하였고, 전기설계사무소의 설계단계에서 적용하는 수용률값을 조사하였다. 조사된 자료의 전체 특징과 중심적인 경향을 알아 보기 위해서 평균값 표준편차, 최대값, 최소값, 중앙값 등의 특징파라메터를 분석하였고, 회귀분석을 통한 선형적인 방법과 비선형적인 방법으로 그 경향을 확인하였다. 그 결과 국내 합성 수용률/부등률 평균값은 46.4%로 나타나 전력용변압기는 용량에 있어서 많은 여유를 가지고 있는 것으로 나타났다. 이를 토대로 변전설비용량의 합리적인 설계를 위하여 부하종별 수용률 기준(안)을 제시하였고, 변전설비용량 산정에 필요한 자료를 데이터베이스화하였다.

In this paper, it has been proposed the simultaneous controller of electronic ballast and PFC(power factor corrector) for fluorescent lamp by one chip micro-controller. Boost DC-DC converter is adopted for PFC, and half bridge inverter for electronic ballast. It controls, simultaneously and independently, the boost DC-DC converter and the half bridge inverter. As electronic ballast and PFC are controlled by one chip micro-controller, it is possible to achieve the cheaper controller for fluorescent lamp. Experimental result has shown the feasibility of the proposed simultaneous controller of PFC and electronic ballast.

This paper proposes a prototype IED hardware design and it's real-time experimental results. To evaluate performance of the IED, the study is well constructed power system model including power transformer utilizing the EMTP software and the testing is made through simulation of various cases. The relaying that is well constructed using DSP chip and RISC CPU etc. has been developed and the prototype IED has been verified through on-line testing by LabVIEW simulator. The results show that an advanced relaying based prototype IED never mis-operated.

In this paper a robust controller using adaptive backstepping technique is proposed to control the speed of a wind turbine system. To make wind power generation truly cost effective and reliable, advanced and robust control algorithms are derived to on-line adjust the excitation winding voltage of the generator based on both mechanical and electrical dynamics. This method is shown to be able to achieve smooth and asymptotic rotor position tracking, as justified by analysis.

A design for the input filter and the output filter of a single-phase uninterruptible power supply (UPS) system is proposed. A filter design example is presented. And also, this dissertation describes a reduction of the DC voltage ripple of a single-phase UPS. The input power of proposed UPS fluctuates with twice frequency of the utility source, which causes DC voltage fluctuation. The reduction of the DC voltage fluctuation requires a large DC link capacitor. The proposed method uses a LC series resonant filter paralleled with a conventional smoothing capacitor. The effectiveness of the proposed method was confirmed by simulation results.

The conventional self-tuning methods have the speed control problem of nonlinear BLDC motor which can't adapt against any kinds of noise or operation circumstances. In this paper, supposed to solve these problem to PI parameters controller algorithm using ANN. In the proposed algorithm, the parameters of the controller were adjusted to reduce by on-line system the error of the speed of BLDC motor. In this process, EBPA NN was constituted to an output error value of a BLDC motor and conspired an input and output. The performance of the self-tuning controller is compared with that of the PI controller tuned by conventional method(Z&N). The effectiveness of the proposed control method IS verified thought the Matlab Simulink.

In this paper, We are going to propose the fire protection system with using CAN(Controller Area Network). The larger, higher and deeper buildings are, the more dangerous people are when fire happens. We should be aware of the problems of prior fire protection system. Therefore, we construct embedded system based on CAN communication that is capable of N:N communication, and build independent fire protection system. If the fire is occurred on the building, the problem is that how fast we can detect the fire and put off it by using available system, this is major factor that reduces damage of our wealth, therefore in this studies We would like to design more stable system than current system. this system that is based on CAN communication which is available N:N communication constructs and is designed to compensate for each fault so that our aim is to reduce the line of system and cost of installation and to suppose future type fire protection system. We are simulated by NIST FDS(Fire Dynamics Simulator) to prove the efficiency of this system.

Frequency is an important operating parameter of a power system. Electric power systems sustain transient frequency swings whenever the balance between generation and load does not no longer hold. To cope with this Constraints, it requires an accurate and high speedy frequency deviation estimation technique and suitable adjustment to obtain the power system energy balance. This paper describes the design, computational aspects and implementation of an iterative technique for measuring power system. The rate change of the phase angle is used for estimation. To confirm the validity of the proposed algorithm, the simulation studies carried out on a typical 154[KV] double T/L system by using EMTP software. Some test results are presented in the paper.

This paper is presented for the development of the brushless DC(BLDC) spindle motors for hard disk drives. A new BLDC Motor has the use of insulated, compacted, iron powder for the armature core material of BLDC motors. Insulated iron powder in this paper is generally called soft magnet composite(SMC). The SMC is used for the stator of the motor instead of the laminated steel core. The motor used by SMC can have the good advantages in condition of the high frequency input power and small sized motor. It gets much more high efficiency than laminated steel core at same input power. The proposed motor has a technique of speed sensorless control. Experimental results show the performance of the proposed BLDC spindle motors for an HDD.

This paper shows how to design a MPPT control of PV system using neural network PI self tuning. The conventional self-tuning methods have the voltage control problem of nonlinear PV system which can't adapt against any kinds of noise or operation circumstances. In this paper, supposed to solve these problem to PI parameters controller algorithm using ANN. In the proposed algorithm, the parameters of the controller were adjusted to reduce by on-line system the error of the output voltage of DC-DC chopper. In this process, EBPA NN was constituted to an output error value of a DC-DC chopper and conspired an input and output. The performance of the self-tuning controller is compared with that of the PI controller tuned by conventional method. The effectiveness of the proposed control method is verified thought the Matlab Simulink.

Electric accidents, like getting electrified, sometimes happen to people working on electricity. A highly probable reason why these electric accidents happen is that workers are used to skip confirming disconnection of electricity when they work. It is mostly because they have little understanding of electricity. To overcome this, various applications such as I electric detecting stick' are invented to check existence of electricity on working environment. But, they have not been popular due to inconvenience of carrying. So, we made a new instrument. It is a kind of nipper on which electric detecter is installed. Detecting existence of electricity is less burdensome via this tool we made.

In this paper, a new estimation algorithm for the rotor speed for SRM drives is described. The algorithm is implemented by the binary observer. The stability and robustness of the binary observer for the parameter variations of the SRM are proved by variable structure control theory. Variable speed control of the SRM is accomplished by the estimated speed. Experiment results verify that the binary observer is able to estimate the speed.

In this paper, we examined channel charge which occurs in electron accumulation after electron velocity saturation. Generally, short gate GaAs MESFET show, saturated electron velocity leading to current satulation. When electron velocity is saturated, deletion layer is still open channel and it plays a key role in deciding saturation current mode we proposed channel charge model in channel after electron velocity saturation.

The simulation of Hydraulic pressure distribution of discharge tube with globular beads and the removal characteristic of Escherichia coli by the discharge tube with globular beads were estimated. The removal characteristic of Escherichia coli was related to the input voltage because the electric field is increased according to input voltage. As the passing amount of test water in discharge tube is increased, the removal ratio of Escherichia coli was increased because passing numbers of electric field section is increased.

Two-dimensional orthogonal variable spreading codes are presented for multiplexing of forward link in direct sequence code division multiple access (DS-CDMA) multiple antennas system And the results of code generation and simulation of 2 dimensional orthogonal variable spreading factors on Jacket matrices are also be investigated. The bit error rate(BER) performance under a multi-user environment for the additive white Gaussian noise (AWGN) channel demonstrated that the proposed scheme could provide flexible rates and lower correlation values

In this paper, we propose the new method that separate the existing common VQ code book into two parts, one is the common VQ code book which is the half of existing common VQ code book, another is the personal speaker VQ code book which accommodate the personal speaker characteristic, variation to improve the performance of the text-dependent speaker verification system using discrete HMM. We apply the propose method m this paper to the text-dependent speaker verification system using discrete HMM and have the improvement performance of about 0.24% compared to existing method

A programmable dynamometer is the proposed system improved the problem of the torque measuring delay with torque transducer, and the load torque is estimated by the minimal order state observer based on the torque component of the vector control induction moter. Therefore, the torque controller is not affected by a load torque disturbance. To verify a superiority of the proposed control algorithm, the analysis for a root locus of a conventional control method and the proposed one, and simulation and experiment is performed. Therefore we hope to be extended in industrial application.

The railway characteristic, which is concerned, as most utilities is unbalance produced by the large single-phase loads. Here are two theoretical concerns associated with unbalanced loads. First, generator rotor heating resulting from unbalanced current flow, Second, there is the possibility of motor overheating in industrial plants, due to the unbalanced voltage. Therefore, the exact assessment of the voltage unbalance must be carried out preferentially as well as load forecast at stages of designing and planning for the electric railway system. This paper proposes a new analysis model to more effectively estimate voltage unbalance. Numerous distributed circuits in the electric railway system are composed by components. The entire system can be easily modeled by the combination of four-port representation of each component in parallel and/or series. Simulation results using the model are compared with field data, and it verifies the accuracy of the proposed model.

In this paper, a multi-functional control module is developed to improve the confidence of CO2 welding. In the developed system, a main controller of an automatic welding system including of I/O port is modulated by microprocessor. The developed multi-functional control module is familiarized to the conventional automatic welding system. Therefore, the confidence of CO2 welding is improved when the main controller of an automatic welding system is broken down.

In this paper, an automatic welding carriage is developed by wireless communication. In the developed system, a data transmission of a automatic welding line tracking is adopted by RF communication. Additional, a welding condition of the automatic welding carriage IS displayed by microprocessor. Therefore, the developed system can overcome the restriction of an operating distance and perform an accurate transmission of the control signal.

본 연구는 스파이랄 벡터에 기초한 유도전동기 모델의 해석을 나타내고 이 해에 기초한 자계가속법(Field Acceleration Method)에 의해 순시 토크 제어와 회생전력 해석을 나타내었다. 전압지령형의 PWM제어에서 전압형 인버터에 의해 전동기가 동작할 때 전력회생이 수식으로 해석 되었다. 전압지령형의 전압 PWM 인버터에 의한 유도 전동기의 속도 서보시스템을 설계하고 이 속도제어 시스템을 이용해 가감속시의 소비(회생)전력을 측정하여 실제 시스템에서 전력 절약정도를 검토하였다. FAM법에 의한 실험을 행하고 유효성을 확인하였다. 고정자 저항의 측정오차나 변동은 여자전압에 맥동이 생겨 출력 토크에 영향이 나타는 것을 알 수 있었다.

The LC filter design procedure of the inverter output filter is described. The transfer function of the filter output voltage to the load current is described with the capacitor value and the system time constant considering the system controller. By using the closed form of the relation between the filter capacitor value and the system time constant, the capacitor value can be calculated with the given system time constant and vice versa. It is more practical for the implementation of power and control circuit of inverter. And as the effect of the load current to the voltage distortion can be calculated from the closed form, it is possible to analyze the system how much the voltage waveform is distorted in case of the nonlinear load. All the proposed design procedure is verified with the simulation and experimental results.