Proceedings of the Korean Society for Noise and Vibration Engineering Conference (한국소음진동공학회:학술대회논문집)
The Korean Society for Noise and Vibration Engineering
- Semi Annual
- /
- 1598-2548(pISSN)
Domain
- Environment > Noise/Vibration Control and Management
2001.05a
-
There passed almost 15 years since our sound quality studies in Japan related to the emitted noise from the industrial products have been started. The sound under consideration are interior and exterior noise from cars, noise from the electric appliances such as electric shavers, electric cleaners and washing machines and the sound emitted from earth moving machines and etc. After a little while since sound quality studies have been started, the products with better sound are gradually on sale on the market.
-
Linear harmonic analysis is a convenient and generally accurate method to use for the acoustic analysis of intake and exhaust silencers for IC engines. The major uncertainty in this form of modelling is the characterisation of the source, which is inherently nonlinear and time-variant. Experimental methods are generally used to determine the source characteristics, and in particular the indirect method is most suitable for an IC-engine source. With reference to an idealised linear time-variant source, it is found that the characteristics of a time-variant source as determined by the indirect method have no physical relevance. The direct method of experimental measurement appears to have some advantage over the indirect method, although in practice it is difficult to apply to an IC engine source. Again, an idealised linear time-variant source can be used to indicate that the characteristics of a time-variant source as determined by the direct method also have no physical relevance. Strangely, these meaningless measured source properties can nevertheless be used to accurately predict the radiated noise from an IC engine and silencer system.
-
Aeroacoustic technology to improve the acoustic comfort in high-speed became a major topic in vehicle development process. Although most of wind noise reduction and sound quality improvements are possible with full vehicle, the countermeasures should be applied at the early design stage. Acoustic holography technology was used to identify the external wind noise sources of a vehicle in Hyundai Aeroacoustic Wind Tunnel. Microphone self-noise reduction techniques and several reference microphone positions are investigated in order to obtain proper results.
-
최근의 대형 디젤 엔진은 고성능, 고효율 및 제작비용 절감 등의 요구에 따른 경량화, 유연화 추세로 설계되고 있는 한편, 엔진 자체에서 발생하는 고유의 큰 기전력 (가스폭발력, 왕복동 관성력, 각종 우력) 때문에 항상 진동 문제에 노출되어 있다. (중략)
-
Floor impact sound has caused many acoustical complaints to the apartment building dwellers. The concrete floating floor construction is one of the most reasonable way to reduce floor impact sound. Recently, many damping materials are used in apartment buildings. In this study, to evaluate floor impact sound insulation performance, field tests were carried at five building floors with damping materials. The test results of impact sound insulation performance for five buildings showed good improvement in light weight impact sound after installation of damping materials, but heavy weight impact sound wasn't improved.
-
Recently, among those general contractors and construction material production companies in korea, this concept is lively obtained to reduce the floor impact sound. This attempt is continuously tried for developing the floor impact isolation material. However the assesment of the isolation performance is often ignored and even there seems no differences in comparison with the general the isolation performance of the floor impact. This is often occurred for their only respect with the material of the floor impact isolation performance. Therefore, this study analysed the expected problems for site application of currently applied the isolation material and its capacity which as the floor impact reducing material, and presented several major assesment items and checklist which should be inspected in advance of their development or site application.
-
Absorbers such as porous materials and panels have limited absorption characteristics to some frequency bands. There is a need for absorbers with high absorption coefficients in a wide frequency ranges to make good response of room acoustics. This is almost impossible for a single absorption material. Composite absorption structure with cover, porous material. and air gap is known to have those wide frequency characteristics. In this basis. various composite absorption structures are measured and investigated as wide range absorption structures. Measurements are performed according to an international standard, ISO 354. Various surface types such as wooden slits, wood/steel perforated panels are selected as surface covers, and also various porous materials such as polyurethanes, polyesters, and glasswools are used inside the covers. Result shows that the area of void parts of surface materials is critical to high frequency absorptions, and thickness of air gaps are critical factor of the peak absorptions of low frequency bands.
-
고층 빌딩의 풍하중에 의한 진동을 제어하기 위하여 MR 유체감쇠기를 이용한 반능동 제어 시스템의 설계에 대하여 연구하였다. 제안된 설계기법의 효율성을 검증하기 위하여 ASCE benchmark 구조물을 대상으로 수치 모의 해석을 수행하였다. 유전자 알고리즘을 사용하여 MR 감쇠기의 76층 빌딩 내에서의 최적위치와 용량을 결정하였으며, clipped optimal control 제어기법을 사용하여 가속도 되먹임 구조를 갖는 MR 감쇠기의 제어 알고리즘을 구성하였다, 수치 모의 해석 결과로부터 MR 감쇠기는 ATMD와 유상한 제어 성능을 가지고 있으며 매우 작은 규모의 파워 시스템만으로 운영이 가능한 효율적이고 안정적인 제어 시스템임을 확인할 수 있었다.
-
In this paper, Power Flow Boundary Element Method(PFBEM) has been developed for one and two dimensional noise and vibration problems in the medium to high frequency ranges. Green functions used for PFBEM are the fundamental solutions of energy governing equations. Both direct and indirect methods of PFBEM have been formulated and numerically applied to predict the vibrational energy density and intensity distributions of simple beams, rectangular plates and L-type plates.
-
The problem of the transient interaction of a plane acoustic shock wave which has an infinitely steep wave front with a cylindrical or spherical elastic shell has been studied analytically from early fifties based on the integral transform and series solution techniques. Huang adopted an inverse Laplace transform, and used a finite number of terms of the infinite series expansion of the equations for the shells. In the 1990s, the results have been used by many authors for validation of computer codes. The object of this paper is to discuss the interaction between a moving source and submerged spherical shells. Since the center of source is moving the first contact location between the waves and shell changes depending on the source velocity and distance. These are considered in the analysis. Furthermore, constant source strength and decreasing strength are considered in the analysis. Radial velocities at several locations on the structure are obtained and the results are discussed.
-
A continuum-based shape design sensitivity analysis (DSA) method is presented for the acoustic radiation from thin body. The normal derivative integral formulation is employed as an analysis formulation and differentiated directly by using material derivative to get the acoustic shape design sensitivity. In the acoustic sensitivity formulation, derivative coefficients of the structural normal velocities on the surface are required as the input. Thus, the shape design sensitivities of structural velocities on the surface with respect to the shape change are also calculated with continuum approach. A simple disk is considered as a numerical example to validate the accuracy and efficiency of the analytical shape design sensitivity equations derived in this research. This research should be very helpful to design an application involving thin body and to change its acoustic characteristics.
-
High intensity vibro-acoustic testing is the appropriate method for flight qualification testing of space flight vehicle which must ensure the acoustic environment of launch. Growing demand for satellites and launch vehicles in korea has resulted in a recent increase in the demand for high intensity vibro-acoustic test facility. The test facility is designed to provide an acoustic environment of 152 ㏈( re 20
${\mu}$ Pa) overall sound pressure level over the band width of 30 Hz to 10,000 Hz in the reverberant chamber. The reverberant chamber has a volume of 1,000 ㎥ with interior dimensions of 8.7m${\times}$ l0m${\times}$ 12m, which can accommodate not only satellites but also launch vehicle payload fairing. Korea Aerospace Research Institute and Korean industries have been carrying out the development of the reverberant chamber and auxiliary devices, such as automatic control system, monitoring/safety device, and jet nozzle, etc. This paper presents the detailed description of High Intensity Acoustic Chamber of KARI, which will be the first and unique testing facility in Korea. -
The structure of hard disk drive(HDD) is excited by dynamic motion of a disk-spindle motor, and it makes sound noise. Therefore, the cover and the base of HDD should be designed to reduce noise and vibration induced by spindle motor. The prediction technique of sound pressure level(SPL) of a given structural shape enables us to design a cover and a base with much less vibration and noise. In this paper, we measured the force of disk-spindle motor and predicted SPL from HDD by computational simulation. To get a SPL of HDD by computational simulation, modal analysis and forced vibration analysis were performed with ANSYS, and sound radiation was computed using SYSNOISE. The calculated results were compared with experimental results and a good agreement was obtained. With this computer simulation procedure and design of experiment(DOE), optimal thickness of noise barrier and damper was calculated.
-
This paper presents field-dependent dynamic characteristics of a shock damper featuring an electro-rheological(ER) damper. A cylindrical type of the shock damper is designed and manufactured on the basis of the field-dependent Bingham model. The damping force is then measured with respect to the piston velocity at various electric fields. The measured damping force is incorporated with the 1DOF shock system to analyze the shock isolation performance.
-
A gyroscope is a rotating body possessing one axis of symmetry and whose rotation about the symmetry axis is relatively large compared with the rotation about any other axis. Tuning fork is this type of structure that various modem gyro-sensors are based on. In this paper, dynamic behavior of a cantilevered beam subjected ta a base rotation with respect to the eccentric axis that is parallel to the beam axis is analyzed. The final equations of motion in terms of generalized coordinates can be solved with numerical scheme with various values of angular velocities and angular accelerations of the rotating axis. In contrast to the case of rotating cantilever beam like helicopter blade, the rotational motion with respect to the beam axis has effect to decrease the stiffness of the beam and has unstable region depending on the magnitude of the rotational angular velocity and angular acceleration.
-
This paper presents the experimental study for the reduction of transmitted shock waves in smart structures incorporating MR insert. MR fluid is filled within the two aluminum layers and two piezoceramic disks are embedded on the host plate as a transmitter and a receiver of the shock wave. Pulse wave generated by the transmitter is transmitted to the receiver through the MR insert and the plate. By applying magnetic field to the MR insert, the amplitude of the transmitted shock wave is reduced remarkably. The attenuation performance is tested by changing the applied magnetic field on MR inserts in two ways: by changing angle of permanent rubber magnet from 90 to 5 with 5 decrements, by using electromagnet in which magnetic field is controllable. The propagating wave speed of MR insert is also investigated.
-
In this paper, transmitted sound reduction performance of smart panels is studied according to different piezoelectric materials with piezoelectric shunt damping. Peizo-damping is implemented by using a newly proposed tuning method. This method is based on electrical impedance model and maximizing the dissipated energy at the shunt circuit. By measuring the electrical impedance at the piezoelectric patch bonded on a structure, an equivalent electrical model is constructed near the system resonance frequency. After shunting elements are connected to the equivalent circuit, the shunt parameters are optimally searched based on the criterion of maximizing the dissipated energy at the shunt circuit. Transmitted sound reduction performance is compared according to different piezoelectric materials with peizo-damping. Two piezoelectric materials are selected: PZT-5 and QuickPack IDE actuator. When resonant shunt circuit is considered, the use of PZT-5 exhibited the good sound reduction performance.
-
Active control of flexural vibrations of smart laminated composite beams has been carried out using piezoceramic sensor/actuator and viscoelastic material. The beams with passive constrained-layer damping have been analyzed by formulating the equations of motion through the use of extended Hamilton's principle. The dynamic characteristics such as damping ratio and modal damping of the beam are calculated for various fiber orientations by means of iterative complex eigensolution method, This paper addresses a design strategy of laminated composite under flexural vibrations to design structure with maximum possible damping capacity.
-
A comparison between theoretical and measured transfer function, which relates structure-borne noise source level to underwater radiated noise, of a naval ship is presented in this study. Transfer functions are obtained by dividing far field underwater noise by the value of structure borne noise source levels below machinery mounts. In prediction, statistical energy analysis of the whole ship structure is used to get vibration levels of wetted hull plates below water line. Then, far field radiated noise is calculated by summing up contributions from each plates using vibration levels and radiation efficiencies. And 1/3-octave band underwater sound pressure at the distance of 1 m away from the hull were measured to get experimental transfer functions. The two transfer functions are compared to show resonable agreements in spite of the subtle physical differences between each other.
-
Relatively high rotating speed propulsion shafting system of the large Ro-Ro Ferry has a greate risk of the resonance of the whirling vibration within the operating speed range. Therefore, it is necessary to control the whirling vibration characteristics of the shafting system in the initial design stage so as not to be resonant with the blade number order excitation in the normal operating speed range. The results of the whirling vibration analysis for l000P Ro-Ro Ferry with SHI's in-house program and the measured results during the sea trial are introduced. Additionally the outline of the program and the calculation method of the major properties are presented.
-
Ship owners are demanding quieter vessels since crews have become more sensitive to their acoustic environment. Accordingly, designers of shipyards need to respond intelligently to the challenging requirements of delivering a quiet vessel. In early design stage, to predict shipboard noise the statistical approach is preferred to other methods because of simplicity. However, since the noise characteristics of the ships vary continuously with the environments, it is necessary to update the prediction formula with data base management system. This paper describes the feature of database program with the prediction method. Database management programs with GUI, are applied to Intranet system that is accessible by any users. Statistical approach to the prediction of A-weighted noise level in ship cabins, based on multiple regression analysis, is conducted. The noise levels in ship cabins are mainly affected by the parameters of the deadweight, the type of ship, the relative location of engines and cabins, the type of deckhouse, etc. As a result of verification, the formulas ensure the accuracy of 3 ㏈ in 83 % of cabins.
-
This study is performed to evaluate and design the vibration characteristics of the onboard machinery with resilient mountings. To reduce the vibration level of onboard machinery with resilient mountings, it is important to evaluate and, if necessary, modify the vibration characteristics of the resilient mountings. In this study, we have developed a program to calculate natural frequencies of the machinery with resilient mountings, forced vibration levels due to internal excitation force of the machinery itself and external excitation forces. of the main engine and the propeller. and the force and motion transmissibility of the resilient mountings. The developed program is also able to be applied to optimal design of the resilient mountings for obtaining a target natural frequency and for achieving a minimum forced vibration level at the center of gravity of the machinery.
-
Recently, mega-float offshore structure is studied as one of the effective utilization of the ocean space. And mega-float structure are now being considered for various applications such as floating airports, offshore cities and so on. This mega-float structure is relatively flexible compared with real floating structures like large ships. when we estimate dynamic responses of these structures in waves, the elastic deformation is important, because vertical dimension is small compared with horizontal. The analysis of the dynamic response as it receives regular wave is studied. The finite element method is used in the analysis of structural section of this model. And the analysis is carried out using the boundary element method in the fluid division. In order to know the characteristics of the dynamic response of the mega-float structures, effects of wavelength, water depth, and wave direction on dynamic response of the floating structure are studied by use of numerical calculation.
-
An electric drill is a handy tool used in a machine shop, which consists of motor, gear, bearing, shaft, and case, i.e., a gear driving system. Low level vibration and noise of the electric drill can bring the assurance of the quality and reliability of the machine. The vibration sources of the electric drill should be investigated for the reduction of the vibration and noise of the system. Through the experiments in a laboratory and the various signal processing procedure for the measured vibration and sound signals, the characteristics of the vibration and noise of the electric drill are investigated. And its propagation path is sought using partial coherence technique.
-
This paper proposes an adaptive feedforward controller (AFC) based on LMS for periodic disturbance rejection in active magnetic bearing system. The proposed controller does not alter the stability and robustness of the existing AMB system. It is shown that the control delay due to the eddy current as well as runout and unbalance can be identified and compensated using the estimated displacement from the measured magnetic flux. The simulation results confirm that the proposed scheme successfully identifies and compensates for the runout, unbalance and eddy current effect, leading to a high-precision magnetic bearing system.
-
A multi-stage reciprocating air compressor has many pistons and conneting rods to one crank throw, while a general engine has one connecting rod. Those make its design hard to apply balance weight design method generally using in an engine design, This study introduces a modified balance weight design method in order to calculate the unbalanced inertia properly. Vibration tests on V/W type air compressor have been conducted to prove the usefulness of design program. It is confirmed that the proposed program is applicable to design of balance weight.
-
Severe vibration was detected during test operation in motor frame of the Turbo Chiller (300RT). To identify the vibration problem, vibration measurement and modal test were carried out. From the test results, it is concluded that the severe vibration occurred due to the resonance between the motor frame horizontal mode and the motor excitation frequency. Therefore the horizontal mode of the frame could be controlled by the sensitivity analysis results for the length of the supporting plate.
-
The performance of printer can be determined by the printing speed, noise level, printing quality which includes the resolution, regularity of printed matter and etc. Among them, printing quality mostly depends on the irregularity of the line spacing and dot size. The irregular line spacing and dot size in laser beam printer are mainly from the jitter which comes from the vibration of Organic Photo Conductive(OPC) drum and the Laser Scanning Unit(LSU). Jitter due to the vibration of LSU appears as high-frequency component which occurs 100-300
$\mu\textrm{m}$ interval in printed matter and the causes of it can be estimated as the vibration of polygon motor, case, reflecting mirror and etc. In this paper, vibration characteristics of the LSU under development are investigated and the strategy for improvement of the dynamic characteristics is established and its validity is demonstrated. -
The dynamic characteristic of the building using preflex composite beams is a low natural frequency due to long span. Therefore, both vibrational acceleration and the characteristic of natural frequency damage to people using the building, This study estimates a vibrational acceleration based on walking and natural frequency in five kinds of building. Recently, using methods of evaluating a serviceability are based on JIA, AISC, Eurocode, CSA, DIN and ISO. ed. The result of this study is content with foreign regulations and serviceability. However, considering of these results, the method of evaluating serviceability should be developed in the future.
-
The paper presents the dynamic stability of a vertical cantilevered pipe conveying fluid and having an intermediate translational linear spring. The translational linear spring can be located at an arbitrary position. Governing equations are derived by energy expressions, and numerical technique using Galerkin's method is applied to discretize the equations of small motion of the pipe. Effects of linear spring supports on the dynamic stability of a vertical cantilevered pipe conveying fluid are fully investigated for various locations and magnitudes of the translational linear spring.
-
In this paper, dynamic stability and vibration characteristics of a flexible shoe in drum brake systems are investigated. The frictional force between the drum and the shoe is assumed as a distributed frictional force, while the shoe is modeled as an elastic beam supported by two translational springs at both ends and elastic foundations. Governing equations of motion are derived by energy expressions, and numerical results are calculated by finite element method. Through the numerical simulation, critical distributed frictional forces are calculated by changing the stiffness of two translational springs and elastic foundation parameters. It is also shown that the beam loses its stability by flutter and divergence depending on the stiffness of elastic supports and elastic foundation parameters. Finally, the time responses of the beam corresponding to their instability types are demonstrated.
-
This paper deals with the free vibration of two identical circular plates coupled with a bounded fluid. An analytical method based on the [mite Fourier-Bessel series expansion and Rayleigh-Ritz method is suggested. In the theory, it is assumed that the ideal fluid is filled in a rigid cylindrical container and the two plates are clamped along the plate edges. The proposed method is verified by the finite element analysis using commercial software with a good accuracy. Two transverse vibration modes, namely in-phase and out-of-phase, are observed alternately in the fluid-coupled system when the number of nodal circles increases for the fixed nodal diameter. The effect of gap between the plates on the fluid-coupled natural frequency is also investigated.
-
Asymmetric beams cause complicated vibration phenomena due to the inherent bending-torsion coupled vibration. In this paper, an exact dynamic element matrix for the bending-torsion coupled vibration of asymmetric beam is derived. An application of the derived exact dynamic element matrix is demonstrated by an illustrative example, wherein the natural frequencies by the proposed modeling method are compared with those available in the literature. Another numerical example is also illustrated which deals with a general beam with joints. The numerical study shows that the exact dynamic element model is useful for the dynamic analysis of asymmetric bending-torsion coupled beams.
-
Recently the impact sound insulation performance is regarded as one of the most import factors in determining the quality of housing environment. In order to reduce the impact sound level transmitted through the floors and structures, establishing the standard level of impact sound insulation performance is needed. In this consideration, The effecting facts for the standard insulation level is reviewed.
-
Revision of KS, Korean Standards, is currently actively discussed. It is just the time for a new world class standards under the new system with WTO, World Trade Organization. This paper is a part of "Researches on the Standards in the Building Acoustic Field", as one of KS revision projects. The aim of this study is to define the requirements for measuring the reverberation time of rooms with reference to other acoustical parameters. In the former KS, there is no items matched with this purpose. Therefore measuring reverberation time and other room acoustical parameters with confidential test procedure was impossible. On these basis, a new part of KS is proposed, and some problems remained and further discussions in the proposed draft are described in this study.
-
This study aims to review the present conditions of domestic laboratory test facilities for measuring impact sound insulation. The result will be useful to establish the new Korean Standard to coincide with ISO 140-6.
-
In evaluating sound performance of building, it is important to carry on tests and evaluations based upon residential sound performances. Korean Standards include test methods on sound performance, but don't include any code on evaluation methods. Therefore, evaluation methods from Japan or ISO have been used for evaluating sound performance in domestic so far. In this study, every regulation from ISO, JIS, ASTM, especially for airborne sound insulation against building and building element, is analyzed in order to apply to establishment of Korean Standards on a sound performance evaluation method in buildings.
-
In this study, the ISO 10534-2 "Determination of sound absorption coefficient and impedance in impedance tubes - Part 2: Transfer function method" was introduced and discussed. In order to make it as Korean Industrial Standard, several main contents of ISO 10534-2 are reviewed. Some experimental results are reconsidered.
-
Floor impact noises in apartment buildings have been investigated as they are most annoying in living environment. Several experiments were undertaken to compare perceived noisiness of floor impact noises generated by bang and tapping machine along with children's jumping and running. Results show that bang noise is more annoying than tapping noise and floor impact noise generated by children is less annoying than the noise generated by machine. The floor impact noise generated by children's jumping and running corresponds well with the bang-machine noise in terms of loudness, unbiased annoyance,
${\Phi}$ $\_$ 0/ and IACC. The noise generated by children is somewhat different from machine noise; in spatial impression the real noise is similar to tapping-machine noise but is less annoying that the machine noises. -
It is necessary to predict the sound pressure level(SPL) in rooms before designing an apartment when exterior noises are produced. In order to predict SPL for an apartment that has some specific exterior noises, the following should be known: the characteristics of outdoor noise, sound insulation performance and sound level differences of each room. The purpose of this study is to find out the possibility of predicting sound pressure level of rooms in an apartment by analysing sound level differences among rooms. Sound sources used in this experiment are construction noise, aircraft noise, railroad noise, road traffic noise and white noise as a reference to compare with the previous four. These noises were recorded and reproduced by speaker. As a result, we found that within the sound reduction pattern, the sound difference level appeared uniform depending on the sound insulation characteristics of the windows installed when facing the noise source. When the windows having the same acoustic performance were installed, the SPL in each room resulted in nearly the same values.
-
For the reduction and efficient management of railway noise, first of all prediction of railway noise is necessarily requested, At home and abroad, many studies for prediction of railway nearby noise have been accomplished, But it is impossible to predict exactly for the Korean Railroad, because the acoustic power DB for each rolling stock used in Korea has not been builded yet. So in this study, acoustic power DB for each Korean rolling stock such as Samaeul, Mugungwha was builded according to the speed and rail support systems. Predicted results using accumulated acoustic power DB are compared with measured results and it is known that accumulated acoustic power DB can be used for more precise prediction of railway nearby noise.
-
Most engineers, related to soil and civil dynamic field, have been interested in the dynamic response of building transmitted from soil and rock to structure due to blasting. However it is not easy to estimate the dynamic response of structures and utilities due to blasting by using analytical method because of difficulties of soil modeling, prediction of excitation force and so on. In this paper, dynamic response analysis have been performed to predict vibration levels of structure due to blasting and the semi-empirical method. which is based on vibration measurement data. has been employed to consider blast vibration characteristics.
-
Partial rotor rub occurs when an obstacle on the stator of a rotating machinery disturbs the free whirling motion of a rotor, which is more common than full annular rub for the cases of rubbing in rotating machinery. The nonlinearity due to the intermittent contacts and friction during partial rotor rub makes the phenomenon complex. The several nonlinear phenomena of superharmonics, subharmonics, and jump phenomenon are demonstrated for the partial rub using an experimental apparatus in this study. A piecewise-linear model and a rebound model using the coefficient of restitution are investigated on the basis of experimental observations in order to adopt as an analytical model of the contact between the rotor and stator during whirling motion. The contact stiffness, coefficient of restitution, and friction coefficient for the contact during partial rub are calculated from the comparison between the numerical simulation and the experimental results. Also, the numerical simulations for the model of partial rub are done for the various system parameters of clearance, contact stiffness, and friction coefficient in order to find the nonlinear behavior of partial rotor rub.
-
The nonlinear vibration of a cantilever beam due to electromagnetic force is studied. The dynamic responses of the beam show various phenomena with the variation of the system parameters, such as jump phenomenon, multiple solutions and the change of the natural frequency. The nonlinear stiffness due to electromagnetic forces which depends on air gap size is measured experimentally. This system was modeled by a single degree of freedom nonlinear dynamic system and solved numerically for the system parameters. The numerical results show good agreements with the experimental observations, which demonstrates the nonlinearity of magnetic force.
-
Three kinds of viscoelastic damper model, which has a non-linear spring as an element is studied analytically and numerically. The behavior of the damper model shows non-linear hysteresis curves which is qualitatively similar to those of real viscoelastic materials. The motion is governed by a non-linear constitutive equation and an additional equation of motion. Harmonic balance method is applied to get analytic solutions of the system. The frequency-response curves show that multiple solutions co-exist and that the jump phenomena can occur. In addition, it is shown that separate solution branch exists and that it can merge with the primary response curve. Saddle-node bifurcation sets explain the occurrences of such non-linear phenomena.
-
An investigation into asymmetric vibrations of a clamped circular plate under a hannonic excitation is made. We examine a primary resonance, in which the frequency of excitation is near the natural frequency of an asymmetric mode of the plate. We found not only a response having the form of standing wave but also one having the form of traveling wave, which was not observed by Sridhar, Mook and Nayfeh(1978; Journal of Sound and Vibration 59(2), pp. 159-170).
-
This research is concerned with the development of a real-time adaptive PPF controller for the active vibration suppression of smart structure. In general, the tuning of the PPF controller is carried out off-line. In this research, the real-time learning algorithm is developed to find the optimal filter frequency of the PPF controller in real time and the efficacy of the algorithm is proved by implementing it in real time. To this end, the adaptive algorithm is developed by applying the gradient descent method to the predefined performance index, which is similar to the method used popularly in the optimization and neural network controller design. The experiment was carried out to verify the validity of the adaptive PPF controller developed in this research. The experimental results showed that adaptive PPF controller is effective for active vibration control of the structure which is excited by either impact or harmonic disturbance. The filter frequency of the PPF controller can be tuned in a very short period of time thus proving the efficiency of the adaptive PPF controller.
-
This research is concerned with development of the passive-active vibration absorber using piezoelectric actuators. This active-passive isolation system consists of 4-pairs of PZT actuators bonded on accordion type of mounting bracket and a spring-damper located in center. Hence, the active system is connected in parallel to the passive system. In this paper, we discuss the dynamic characteristics of the addressed system. Based on the series of experiment, it is found that the proposed system can cope with the external disturbances. The controller design is currently under investigation.
-
Magneto-Rheological fluid (MR fluid) is known as a class of functional fluid with controllable apparent viscosity of the fluid by the applied magnetic field strength. Extensive researches with the functional fluids have been done on applications of the fluid to mechanical components such as suspension, absorber, engine mount, clutch, break, valve, etc. In this study, a new torsional damper using MR fluid is proposed, and the response property of the damper was theoretically investigated. The present damper is quit effective for reducing the driveline vibration in a wide range of the engine speed.
-
This paper deals with sensing ability of smart sensor that has a sensing ability to distinguish materials according to surface types of smart sensor. We have developed a new signal processing method that can distinguish among different materials. The smart sensor was developed for recognition of materials. We made two types of smart sensors in our experiment. Then, we estimated the ability to recognize objects according to smart sensor type. We estimated the sensing ability of smart sensor with the
$R_{SAI}$ method. Experiments and analysis were executed to estimate the ability to recognize objects according to surface types of smart sensor. Sensing ability of smart sensors was evaluated relatively through a new$R_{SAI}$ method. Applications of smart sensors are for finding abnormal conditions of objects (auto-manufacturing), feeling of objects (medical product), robotics, safety diagnosis of structure, etc.etc. -
Electrorheological(ER) and magnetorheological(MR) fluids have a unique ability to increase the dynamic yield stress of the fluid substantially when electric or magnetic field is applied. Controllable fluids such as ER and MR fluids have received considerable attention as several components of engineering devices. One of them is a smart impact damper using ER/MR fluids. Impact damper system can be used in the joint mechanism of railroad vehicle, protection equipment of elevator's drop, and launch equipment of aircraft. This paper presents the results of an analytical study of the performance of a smart impact damper to suppress vibration during impact excitation. The damping capabilities of MR impact damper for variable applied current are analyzed using Bingham model under sudden impact load.
-
Up to now. vibration analysis and vibration engineering have been developed, encompassing the aspects of both experimental and analytical techniques. Using experimental modal analysis or modal testing, the mode shapes and frequencies of practical structure can be measured accurately. Curve-Fitting Method is realized through experimental modal identification. In the experimental modal parameter estimation, the estimation of modal damping factor is difficult for complicated and large structure. Also numbers of Selected mode are determined before the procedure. This paper describes the vibration shape of the super-structure model of ship through experimental modal analysis.
-
The bubble cavitation and cloud cavitation are the major sources of cavitation-induced sound and vibration. A numerical method which predicts the trajectory and volume change of a cavity is developed, to predict the cavitation noise of a body. It is shown, by using the numerical method, that the cavitation inception and events rate is strongly dependent on the screening effect caused by the pressure gradient around a body, which is confirmed experimentally. Additionally, the effectiveness of a cavitation control method utilizing air injection is investigated experimentally. It is demonstrated that the noise level of the cloud cavitation can be significantly reduced by the air-injection method.
-
Water tunnel에서 반향음의 영향을 효과적으로 배제하고 수중 소음원의 위치 및 소음 수준을 계측하기 위하여 하이드로폰 어레이 시스템을 개발하였다. 계측 시스템의 신호 대 잡음비를 개선하기위해 48채널의 하이드로폰 어레이를 사용하였고, 당사 고유의 하이드로폰 설치 방법을 개발하였다. 개발된 설치 방법은 터널 벽면의 난류 변동 압력의 영향을 감소시켜 200Hz-1KHz 영역에서 통상적이 설치 방법 대비 약 20㏈ 의 신호 대 잡음비 개선 효과를 얻었다. 또한 40KHz 이상의 주파수까지의 수중 방사 소음 계측을 위하여 100kS/s의 고속 동시 데이터 획득 장치를 개발하였다. 개발된 하이드로폰 어레이 시스템은 성능 시험을 통하여 20KHz 이내의 주파수 영역에서 단일 소음원의 위치를 비교적 정확하게 찾아낼 수 있었다.
-
In order to verify the performance of acoustic-based communication systems, a reliable check-up method is needed, which simulates similar oceanic conditions in low cost. One of the possible candidates would be the performance test in an underwater anechoic basin producing no reflecting waves. For this purpose KRISO (Korea Research Institute of Ships and Ocean Engineering) have constructed an underwater semi-anechoic basin from 1999 to 2001. This paper describes its design procedure, especially, how the material and size of the absorbing walls were chosen. Experiments were also performed to check its anechoic quality, Comparing the results with simple analytical results we concluded that the anechoic basin is working well for some selected frequency ranges.
-
A research to maximize the force transmitted from a vibration motor at the vibration mode, installed in the cellular phone jig, is presented in this study. When the natural frequencies corresponding to the structural vibration modes of the set exist within the range of the driving frequencies acquired by changing the RPM of the vibration motor, the structural vibration resonance is applicable to maximization of the vibration force sensible to the human body such as hands, arms, and hips. The analytical modal analysis using the Finite Elements and the experimental modal testing for the set jig were performed in order to understand the structural modes and the corresponding frequencies. Then the dynamic responses of the set jig to the given driving frequency were measured and the results on maximizing the vibration were confirmed by the FEM dynamic simulation.
-
A reciprocating compressor unit with variable rotating speed driven by BLDC motor is mounted inside hermetic chamber on an internal suspension composed of 4 coil springs and a discharge pipe. A method for predicting the dynamic behavior of compressor frame is required to reduce the transmitted vibration level. Mechanical characteristics such as mass, spring and discharge pipe stiffness properties are obtained with experimentation. To confirm the vibration model for compressor frame, free vibration analyses are performed with theoretical and experimental methods. Results for analytical and experimental investigations on dynamic behavior of the compressor frame are presented, and the agreement between measured and predicted results are satisfactory.
-
A major concern on high-energy centrifugal pump is the potential for interaction of two-phase flow phenomena with mechanical response of the pumping elements. The other concern is the pressure pulsations created from trailing edge of the impeller blade and flow separation and recirculation at partial load in centrifugal pumps. These interactions generating between rotor and casing cause dynamic pulsation on pump and exciting pipeline vibration. The higher severity responses, the more lead to failure of pump and system components. Finally, it cause severe axial vibration of single stage pump due to the hydraulic instability in flow condition below BEP.
-
The satellite electronic equipment is exposed to high level random vibration environment during the launch of spacecraft. The random vibration can cause damage of electronic equipment. Thus very careful consideration on the launch environment, especially for high level random vibration, is required in the design stage of transponder equipments of communication satellite. For the structural integrity of the communication satellite transponder equipment under qualification level random vibration, Finite Element analysis was carried out using the commercial code, MSC/Nastran and ANSYS and stress levels are presented. In order to validate the femodel, modal test was also performed and compared with numerical results.
-
The household reftigerator's noise which is closely related with resident environment can hardly be evaluated its sound quality using the Korean Standards. Radiation characteristics of compressor noise consist of tonal noise in low frequency range and, or narrow band noise in high frequency range. In this study, measuring method for detecting the abnormal and low-level noise in high frequency band is presented, and control method for its reduction is proposed. After installing wall which is similar to living condition, we determined a major concerning frequency band of noise. It can be found the directivity of high frequency noise radiated from compressor by using experiment and analysis. According to isolation of noise transfer path, remarkable noise reduction is achieved.
-
Vibration Characteristics of the Axially Moving Continuum with Time-Varying Length: Spagetti ProblemTime-dependent frequency and energy of free vibration of the Spagetti problem, that is the axially moving continuum with time-varying length, are investigated. Exact expressions for the natural frequency and time-varying vibration energy are derived by dealing with traveling waves. When the string length is increased, the vibration period increases, but the free vibration energy varies as a function of both translating velocity and boundary velocity of the continuum. However, when the string undergoes retraction, the vibration energy increases with time, String tension together with non-zero instantaneous velocity at the moving boundary results in energy variation.
-
Pulsations, vibration and stress are the basic dynamic phenomena in power plant piping systems which directly affect system reliability. These phenomena are both acoustical and mechanical in nature and are closely interrelated. It was noticed that thermodynamic parameters were changed after replacing with new type tube bundles of reheat exchanger. It was reported later that the drain piping connecting the new bundle header with the associated drain tank is regularly pulsating at about every 3 second with 13.4㎐ and 7.5mm, p-p in amplitude. This amplitude is about 6 times higher than reference level of sound piping. The results of finite element analysis of the pipeline showed that its dominant natural frequency is 13.4㎐. The soundness is predicted whether the bending dynamic stress evaluated excesses the maximum allowable high cycle fatigue stress or not by the measured amplitude of vibration.
-
Thermally induced vibration response of composite thin walled beams is investigated. The thin-walled beam model incorporates a number of nonclassical effects of transverse shear, primary and secondary warping, rotary inertia and anisotropy of constituent materials. Thermally induced vibration response characteristics of a composite thin walled beam exhibiting the circumferentially uniform system(CUS) configuration are exploited in connection with the structural bending-torsion coupling resulting from directional properties of fiber reinforced composite materials and from ply stacking sequence. A coupled thermal structure analysis that includes the effects of structural deformations on heating and temperature gradient is investigated.
-
A modeling method for the vibration analysis of rotating composite cantilever plates is presented. Explicit mass and stiffness matrices are derived by considering the coupling effects between extensional motions and the bending motion, To confirm the accuracy of the method presented in this study, numerical results are obtained and compared to those of a commercial program. Numerical results show that the coupling effect among the three motions becomes important for the accurate estimation of natural frequencies as laminates are stacked up unsymmetrically. Also, natural frequencies loci veering, loci crossing, and mode shape variations are observed.
-
In this research, reliability based optimum design is presented for the thin walled beam structures. Deterministic and stochastic optimum design are compared for the thin walled beam structures. Monte Carlo simulation is used for stochastic optimum design with consideration of probabilistic distribution of representative section properties of the thin walled beams with the Response Surface Method.
-
Theoretical analysis of noise reduction by a membrane-duct system is presented. When acorn waves propagate in the membrane-duct, the membrane is also excited and its motion is coup with interior medium. It has been shown that propagating waves with supersonic wave speed exist beyond a certain critical frequency that is determined from the mass ratio of the me and the fluid. Also found are subsonic waves which couple strongly wi th the membrane a provide a powerful mechanism of energy dissipation. Existence of an exterior medium alter dispersion characteristics. It provides additional mass loading and reduces the subsort speed further. The effect of mean flow speed on dispersion characteristics is also consider results show that the membrane-duct system can be applied to diminish and absorb 1 frequency noise in duct instead of passive muffler, such as a simple expansion chamber absorption material.
-
Conventional smart foam is not applicable to active noise control in a duct having flow. Thus, this paper presents a ring-type smart foam as an alternative. The ring-type smart foam consists of polyurethane acoustic foam of lining shape and PVDF film embedded in the foam. The embedded PVDF element acts as an actuator to reduce noise at lower frequencies and the foam absorbs noise at higher frequencies. A feedforward adaptive filtered-x LMS controller is used to minimize the signal from the error microphone. Experiments are executed to reduce broadband and tonal noise.
-
The active structural control has emerged as structural safety of structures against natural loadings such as earthquake and wind loadings. Of many control algorithms, Sliding-Mode Control (SMC) can design both linear controller and nonlinear controller. The robustness against parameter variations as well as excitation uncertainties that is imparted to the SMC due to its nonlinear control action, could make SMC an attractive control algorithm when dealing with structures where the external excitation constitutes the main uncertainty in the system. This paper demonstrates experimentally the efficacy of the SMC algorithm based on the active mass driver system in reducing the response of seismically excited buildings. The SMC control strategy is verified with the experimental study on the one-story building model equipped with the active mass driver.
-
We provide methods to simulate noise propagation for an outdoor environment. Forward tracing method traces sound vectors from sources to receivers while geometry based computation finds all possible sound propagation between sources and receivers geometrically. We discuss defects in relying on a forward tracing method, and suggest a geometry based method. Geometry based method considers all possible direct and indirect(propagation via limited number of reflections) sound propagation saving computational time compared to forward sound tracing. Our simulation results are visualized using VRML(Virtual Reality Modeling Language).
-
Noise radiated from pile driving operation is one of major sources of community noise pollution and thus its operation method is strictly restricted by regulations. Although the drilling method is now used been commonly used in urban areas because of its activity, the benefit of low noise decreases due to high working cost. In the present work, noise characteristics of pile driving operation are carried out. Based on the study result, a low-noise pile cap for driven piles is developed in order to satisfy both the noise level restriction and the economical efficiency. Effects of pile cap are investigated by a scale model experiment, which is focused on the variation of impact force and sound pressure level. The results show a good possibility of noise reduction by an appropriately designed pile cap.
-
도로교통소음의 저감을 위해 설치되는 방음벽의 성능평가를 위해서는 흡음률 및 투과손실과 같은 음향성능에 대한 평가뿐만 아니라, 풍압 및 충격하중과 같은 구조성능과 방음판 제작에 사용되는 재질에 관한 성능평가도 수반되어야 한다. 따라서, 본 논문에서는 이러한 방음벽의 성능평가를 위한 음향 구조 및 재질에 관한 시험 및 평가방법을 제시하였다.
-
Holography Interferometry 와 Speckle Interferometry는 넓은 응용범위를 갖는 유용한 광학적 시험 기술이다. 이러한 홀로그래피 간섭계와 스페클 간섭계를 이용하여 기계 산업에 있어서 제품 개발기간을 단축시키고 품질향상을 위해 수행된 소음, 진동 문제점등에 대한 원인규명 연구 등에 대하여 토의될 예정이며 또한 기존의 유한요소해석과 같은 해석적인 방법과 실험적인 방법의 효율 상에서의 차이점 등에 대해서도 토의될 예정이다.
-
The aeroacoustic phenomena in the simple rectangular open cavity are well published by many researchers. But the geometry shapes of aircraft landing gear wells, weapon bays, etc. are more complicate than that of the simple retangular cavity. They are more similar to the cavity having cover-plates at adges, or Helmholtz resonator. Therefore, the effects of cover-plates existing on edges of rectangular open cavity are numerically investigated in this paper. The compressible Navier-Stokes equations are solved for two-dimensional cavities with laminar boundary layers upstream. The high-order and high-resolution numerical schemes are used for the evaluation of spatial derivatives and the time integration. Physically correct numerical boundary conditions and buffer zone techniques are implemented to produce time-accurate solutions in the whole computation domain. The computational domain is large enough to directly resolve a portion of the radiated acoustic field. Results show that the cover-plates existing on edges of cavity reduce the noise convected from cavity, make the frequency of noise become higher, and change the directivity pattern. So these results can be used in the design of a low noise cavity.
-
This paper describes the characteristics of wind induced noise from high-voltage overhead transmission facilities which include transmission lines. insulator strings. and aviation beacon spheres installed on the overhead ground wires. High-voltage overhead transmission lines generate an audible wind noise due to the alternate shedding of wind-induced vortices. The frequency spectrum from the insulator strings reveals its resonance peak. This resonance sound mechanism has been supposed the self-excitation phenomenon of the resonance and the velocity fluctuation. The booming noises from the aviation beacon spheres are detected and analysed.
-
In this paper, Firstly, it is shown that the high vibration and noise source of piping and pump system is the acoustic resonance. Secondly, in order to decrease the high vibration and noise of piping and pump system, the acoustic mode of piping have been changed and its effectiveness is investigated as applied it at piping system practically.
-
We experimentally attempted to understand the vibration characteristics of a flexible pipe excited by vortex shedding. This has been extensively studied in the past decades (For example, see [2-9]). However, there are still areas that need more study. One of them is to study the relation between spatial characteristics of a flow induced vibrating pipe, such as its length, the distribution of wave number, and frequency responses. A non-linear mechanism between the responses of in-line and cross-flow directions is also an area of interests, if the pipe is relatively long so that structural modal density is reasonably high. In order to investigate such areas, two kinds of instrumented pipe were designed. The instrumented pipes, of which the lengths are equally 6m, are wound with rubber and silicon tape in different ways, having different vortex shedding conditions. One has uniform cross-section of diameter of 26. 7mm, and the other has equally spaced by 4 sub-sections, which are composed of different diameters of 75.9, 61.1, 45.6 and 26.7mm. Both pipes are towed in a water tank (200m
${\times}$ 16m${\times}$ 7m) so that they experienced different vortex shedding excitations. The towing pipe experiments exhibit several valuable features. One of them is that the natural frequencies and their corresponding strain mode shapes dominate the strain response of the uniform pipe. However, for those of non-uniform pipe, the responses are more likely local and many modes participate in it. -
Recent trends in information storage devices disk are the transition from CD drives to high density DVD drives, the development of writable disk drives and the appearance of several high-density portable disk drives. In some flexible disk drives, self-excited disk vibrations become severe as rotation speed increases near or above critical speed. Critical speeds of CD/DVD, ASMO and floppy disks are experimentally measured and compared with analytical predictions. Flutter instability caused by aero-induced disk vibration at high speeds are experimentally observed. In ASMO, three nodal-diameter mode experiences its flutter at 8750 rpm with the frequency lock-on phenomenon. The CD/DVD disk does not have the aero-induce flutter up to 14,000 rpm.
-
This paper deals with an analysis and countermeasure for improving the shock performance of laptop computers. The shock analysis is carried out by using the commercial program of LS-DYNA3D. Also the analysis is verified by the measurements from modal tests and shock tests. The available countermeasures are investigated theoretically and experimentally to find the effective methods of reducing the shock acceleration on hard disk driver during one side fall test. The hard disk drive is the most sensitive part in a laptop computer. This research shows the effects of the spring constant of rubber pad, the reinforcement of mechanical parts and the location of a hard disk driver, on the shock reduction.
-
The suspension of the optical pickup actuator is damped by the presence of silicone rubber damper bond at its termination. In spite of the presence of it, the actuator still exhibits a strong mechanical resonance which affects its settling time and vibrational characteristics. This resonance can cause errors in reading information from the disk, particularly in high speed CD-ROM and DVD-ROM drives. Ferrofluids are stable colloidal suspensions of sub-micron sized magnetic particles in a carrier liquid. In the actuator design, ferrofluid is applied to the surface of the magnets until the quantity is sufficient to maintain intimate contact with the bobbin/carrier assembly. The fluid is retained in the magnetic field and its viscosity provides the desired mechanical damping to the moving assembly, improving the actuators settling time and vibrational characteristics. Access time is also improved, particularly on warped or eccentric discs.
-
CD-ROM drive is improved in rotation speed up to 10,000 rpm. But Vibration and Noise are also increased simultaneously more and more. So many attempts are tried to reduce the unexpected effects. Most attempts are not enough to cover the increasement of Noise and Vibration. Merely availed tries are accumulated in many part and it makes the structure complicated. The Axiomatic approach could arrange the order of design and estimate the optimum design in good oder. In Axiomatic Approach, the composition is divided by Customer Requirement, Functional Requirement, Design Parameter and Design Matrix in large portion. This method also could show more effective way to design before making a prototype.
-
Several kinds of vibration problems have been frequently encountered in industrial vertical pumps in spite of their widespread use for long time. In fact, vibration problems of the vertical pumps are so complicated and difficult with compared to those of the horizontally mounted pumps that more careful attention should be taken for solving the vibration problems. This paper introduces a case study experienced from troubleshooting for excessive vibration occurred in a vertical-type condensate pump for combined cycle power plants. Subsynchronous whirl vibration was caused by the instability of the guide bearing whose lubricant is water. A newly modified guide bearing has solved the vibration problem, which should be the best countermeasure.
-
A 300Wh class flywheel energy storage system using high Tc superconductor bearings(HTC SFES) is being developed by KIMM and KEPRI. HTC SFES consists of a flywheel rotor, superconductor bearings, a motor/generator and its controller, touch-down bearings, vacuum chamber, etc. Stiffness and damping values of superconductor bearings were experimentally estimated to be 67,700N/m and 29Ns/m respectively. The present HTC SFES was designed to have maximum operating speed of 33000 rpm, which is far above 2 rigid body mode critical speeds of 645rpm and 1,275rpm. Leaf-spring type touch-down bearing were utilized to have the system pass safely through the system critical speeds. It has been experimentally verified that the system can run stably up to 28,000 rpm so that HTC SFES is now expected to reach up to its maximum design speed of 33,000rpm without any difficulties. The Halbach array motor & generator has also been proven its effectiveness on transferring electrical energy to a rotaing composite flywheel in kinetic form.
-
The dynamic performance analyses and tests for a 50kW turbo-generator (KIMM-TG50) were carried out. The operating concept of this machine is that it gets the initial driving force from the built-in motor-generator until it reaches its self-sustaining speed of 40,000 rpm, and then the driving mode is changed to self-operating mode by the combustor installed between the centrifugal compressor and the turbine. Due to winding mistake of motor-generator, the system could go only up to 22000 rpm by the motor so that high pressure air externally fed into the turbine was utilized to get the system to run up to 62,000 rpm thereafter. The vibration data collected during the tests revealed that the first bending critical speed is in near 5,600 rpm as predicted in the design stage of the rotor-bearing system, and that there were no other identifiable critical speeds up until 62,000 rpm due to high damping from the squeeze film damper-bearings supporting the rotor. This paper presented some of the experimental results along with dynamic performance predictions made in the design stage as a part of progress being made.
-
Basic equations and its solution procedure are derived for the analysis of an annular pump seal in which the rotor has a large static displacement from the centered position. The Bulk-flow is assumed for a control volume set in the seal clearance and the flow is assumed to be completely turbulent in axial and circumferential direction. Moody's wall-friction-factor formula is used for the calculation of wall shear stresses in the control volume. For the reaction force developed by the seal, linearized zeroth-order and first-order perturbation equations are developed for small motion about an eccentric position. Flow variables are expanded by using Fourier series for the solution procedure. Integration of the resultant first-order pressure distribution along and around the seal defines the 12 elements of rotordynamic coefficients of the eccentric annular pump seal. The results of leakage and rotordynamic coefficients are presented and compared with the Marquette's experimental results and the San Andres' theoretical analysis.
-
A Study on the Vibration Characteristics of Weaving Machine Structure using Component Mode SynthesisIn these days. the finite element method(FEM) is a very common method for not only a simple vibration analysis but also the optimization of structures. Since the finite element model may contain thousands of degree of freedom, the eigensolutions require extreme computing power, which will result in a serious time-consuming problem. Thus, many researchers have challenged to find more improved modeling techniques and calculating methods to overcome such problems. The Guyan reduction method and the substructure synthesis method are typical examples of such methods. Of the substructure synthesis method, the component mode synthesis method (CMS) is widely used for dynamic analysis of structure. In this study. for the efficient analysis of jet loom structure. Component Mode Synthesis was carried out. The results of the finite element program developed are compared with those of the commercial package program ANSYS for the validation of the program. The results obtained by the program showed a good agreement with those of ANSYS. The program will be further refined and verified by test to yield more accurate results.
-
In case of small motors, coil bundle occupies a large portion of stator in view of mass and volume as well as dynamics. It is observed through modal test on the stator of an IPM BLDC (interior permanent magnet brushless direct current) motor that coil bundle wound on the stator core causes the first and second natural frequencies to decrease by about 20-30% compared with those of bare stator. Especially the third natural frequency is newly observed below 3 KHz, which is not observed on the bare stator. It is found that at the third mode the end-coil and the core vibrate out of phase in radial direction. In this paper, the stator is dynamically modeled in terms of the core and the coil bundle consisting of the end-coil and the slot coil based on the above observations for the prediction of dynamic properties. The core can easily be modeled using finite element method with its actual material properties and geometric shape. The concept of equivalent bending stiffness is used for modeling of the end-coil so that predictions may match with the measured natural frequencies for the end-coil cut out of the stator. Although the same concept can be applied to the slot coil, separation of the slot coil from the stator is impractical. Therefore, equivalent bending stiffness of the slot coil is determined through iterative comparisons with the measurements of natural frequencies of the stator with the slot coil in it.
-
Space Test Department at KARI(Korea Aerospace Research Institute) plans to carry out the GVT(Ground Vibration Test) for the KSR(Korea Sounding Rocket)-III FM(Flight Model) which is being developed by Space Technology R&D Division. KSR-III will be an intermediate to the launch vehicle capable of carrying satellites to their orbits. GVT offers very important information to predict the behavior of KSR in its operation, and to develop the flight control and aerodynamic analysis. For development of test facilities, testing and analysis methods which can be used for the future test, Space Test Department has performed the GVT with KSR-II PFM(Proto-Flight Model) at Satellite Integration & Test Center of KARl This paper discusses the procedures, techniques and the results of it. In this test, to simulate free-free condition, test object hung in the air by 4 bungee cords specially devised. The GVT was carried out using pure random excitation technique with MIMO(Multi-Input-Multi-Output) method with three electromagnetic shakers, and poly-reference parameter estimation was used to identify the modal parameters. As the result of the test, 11 mode shapes and modal parameters below 200㎐ were identified and compared with analytical results.
-
When operating lathe gear box which is equipped with geared transmission, it sometimes generates loud noise and excessive vibrations. In order to identify their causes, in this study, torsional and lateral vibration characteristics including critical speeds of the gear transmission system are firstly analyzed using lumped parameter models. Natural frequencies and mode shapes of the gear box structure are also analyzed by using the modal test. Furthermore, measured vibration and noise signals during operations are analyzed and compared with theoretical analysis results. After all, it is concluded that the primary cause of the excessive noise and vibrations is the resonance between gear meshing frequency including its side bands, the frequencies of shaft bending and torsional vibrations, and the natural frequencies of the gear box structure. Consequently the noise and vibration levels are greatly reduced by avoiding resonance between the natural frequencies and gear meshing frequencies through the rearrangement of the gears on the transmission shaft without any gear ratio change.
-
In order to apply into a compact and reliable centrifugal blood pump, this paper introduces a self-bearing motor in which a rotor is rotated without contact. The rotor is actively controlled in only radial directions, while the axial and tilting motions are passively stable owing to the disk-shape structure of the rotor. A prototype was made in outer-rotor type that is far better in the compactness than inner-rotor type. The prototype could be driven up to 8000 rpm with the rotor vibration under 0.12mm. The maximum cardiac output and pressure head were 9 L/min and over 200 mmHg, respectively. These experimental results show that the proposed self-bearing motor has sufficient performance for application to a real blood pump.
-
대상 기계구조물의 유한요소 모델로부터 구한 해석결과가 실험결과와 오차를 나타낼 때, 이러한 오차를 줄일 수 있도록 유한요소 모델의 변경이 요구된다. 유한요소 모델개선은 이러한 역문제(Inverse Problem)를 다루는 체계적인 접근법이다. 일반적으로 유한요소 모델에서 변경할 수 있는 매개변수의 개수는 실험결과의 개수보다 많으므로 실험결과와 일치되는 개선된 유한요소 모델은 무한하다고 할 수 있다. 그러나, 개선된 유한요소 모델이 물리적 타당성을 갖도록 매개변수의 변경량에 제한을 주면 일반적으로 초기 유한요소 모델에 비해 실험결과와의 오차가 개선된 근사해만 존재하게 된다. 따라서, 모델개선 과정을 통해 구한 개선된 모델은 오차의 평가기준 또는 목적함수에 따라 정해진 다양한 근사해 중 하나이다. 기존의 모델개선 방법에서는 단 하나의 오차 평가기준 또는 목적함수를 사용하고 이를 최소화 하는 모델을 구한다. 개선된 모델을 구하기 이전에는 사용된 평가기준이 타당한지 검토할 수 없으므로 대부분의 경우, 시행착오법으로 목적함수를 설정하게 된다. 본 논문에서는 다목적 최적화 기법을 이용한 오차 평가기준을 소개하고 이를 하드디스크커버 유한요소 모델개선에 응용한다.
-
Hydroforming, the new production technology, has been used to manufacture many parts of vehicle in the recent auto industry. When Hydroforming is applied, it is possible to make parts simplification and flexible alteration of section shape in many advantages such as weight reduction, number of parts reduction or performance improvement. This research into shape optimization which reduces number of parts and weight maintaining performance was achieved. In this paper, the COWL CROSS BAA and MT'g BAKT parts of A car STEERING support SYSTEM was introduced by using Hydroforming.
-
Identification of damage of structures has recently received considerable attention in the light of maintenance and safety assessment under service loads. In buildings, the current techniques of safety assessment largely depend on partial experiments such as visual inspection, destructive and nondestructive tests which lead to overconsumption of time and cost as well as higher labor intensity. Therefore, a new trial for safety assessment is urgently needed today. In this respect, the vibration characteristics of buildings have been applied steadily to obtain a damage index of the whole building, but it cannot be established as a practical method until now. This study is aimed at investigating the application of damage identification methods using vibration characteristics of building. Numerical tests are performed on a apartment building. From the test results, it is observed that severity and location of damage can be estimated with a relatively small error by using natural frequency and mode shape data.
-
For several decades many researchers have studied various algorithms, known as non-destructive testing, to identify abnormalities within a structure. Damage detection technique using vibration signal is a kind of these methods. Many researchers have published lots of papers dealing vibration signal to identify structural damage. All the methods for damage detection using vibration signal can be divided into two big categories. The first category is the method that requires some reference model such as finite element model, and the second is the method that does not require any reference model but needs only experimental data. This paper will be devoted to classify damage detection methods that utilize vibration signal.
-
Vibration transient generated by developing localized fault in gear can be used as indicators of condition monitoring in a gear. In this paper, we propose the phase map for a fault signal using continuous wavelet transform to detect this vibration transient. Local fault induces the abrupt fluctuation of load exciting tooth and phase lag in the vibration signal measured on the gearbox. The relatively large fault like "tip breakage" easily can be detected by the clear fluctuation of exciting load. However, minor fault like "initial pitting" cannot be detected using the load fluctuation. To detect this kind of minor fault, the phase map for a fault signal is taken into account. The phase lag by minor fault is observed well in the phase map.
-
본 논문에서는 중수로 원자력발전소에서 사용되는 핵연료 교환기 브리지의 상태를 감시하는데 필요한 진단 방법을 도출하였다. 핵연료 교환기는 고방사능 지역에서 작동하기 때문에 신호의 취득은 원격에서 비침투적으로 이뤄져야한다는 제약이 있다. 따라서 비침투적으로 원격에서 측정 가능한 신호들이 선정되었고 선정된 신호를 이용하여 정확한 진단을 위해서 필요한 여러 가지 진단 신호들의 장단점을 비교하였다. 진단 신호로는 모터의 출력 토크를 선정하였고 진단 신호의 타당성을 모형 브리지를 대상으로 수행한 실험을 통하여 검증하였다. 그리고 마지막으로 다양한 환경에서 실험을 하여 브리지의 작동 특성과 결함과 진단 신호와의 관계를 살펴보았다.
-
In order to distinguish fault electric motors automatically in real time. an intelligent diagnosis technique may be required. This paper presents an automatic fault detection system for electric motors by using their acoustic noises. Time signals of each candidate motor were measured in an anechoic chamber for further analysis. Spectral analysis was first carried out and they showed that two typical types of fault motors could be successfully distinguished in the frequency domain; bearing faults and scratches. Unlike the trend of normal motors that shows only a single dominant peak at around 2000 ㎐, several peaks are bunched together in bearing fault motors. On the other hand, large frequency noises at around 6500 ㎐ are newly arisen in scratchy fault motors. However, the processing time for spectral analysis was rather long for a real time application in production lines. Thus, a number of band-pass filters were used in the time domain instead for a real time application. Before applying filters, the bands of filters were set from the information of spectral analysis. By applying a set of band-pass filters, the RMS values of each filtered signal were calculated, and thus the normal and damaged motors could be successfully distinguished.
-
In this paper, the eigenvalue sensitivity of vehicle powertrain was investigated by analytic method. The powertrain system was considered as a rigid body with multiple engine mounts, and the engine mounts were supposed as three linear springs in three orthogonal directions. The design parameters for the sensitivity analysis were engine mount properties (positions, stiffness, and orientations) and powertrain properties (mass, second moment of inertia, and center of gravity). Firstly, an effective form of eigenvalue problem for the powertrain system was introduced. Then, the analytic sensitivity of eigenvalue was derived using the equation. Lastly, the derived sensitivity equation was applied to a real powertrain system to provide its correctness and applicability.
-
The road traffic noise becomes aggravated due to the rapid increase of motor vehicles. It has a great effect on the dwelling environment. Therefore we investigate the characteristics and sources of the motor vehicle noise through grasping the status of the motor vehicle noise. Traffic noise results from the collective contribution of the noise produced by individual motor vehicles. The motor vehicle noise varies enormously depending upon its type and mode of operation.
-
Suppression of very low-frequency noise from an automobile exhaust system is difficult due mainly to its large wave length. Therefore, the configuration of total exhaust system, i,e., piping and muffler layout, is important at low frequencies. In this paper, an optimal layout technique of exhaust systems has been developed for reducing low-frequency exhaust noise. For this purpose, system insertion loss and virtual attenuation coefficient have been defined by considering the effects of mean flow and temperature gradient in the pipe. The applicability of present method is investigated with an actual automobile exhaust system and an optimized layout of pipes and mufflers is suggested.
-
Experimental approach was investigated to improve gear rattle noise of a small car. During the development of a small car serious problem occurred inside the transmission gear units. The transmission was a carried over system from a less powered predecessor. Several components of suspicion were investigated, and applied to reduce rattle noise. In general, backlash, the assembly gaps, and the clutch disk rattle induce gear rattle noise. Above mentioned improvements were applied to reduce the noise, but still problem remained. Meanwhile, the temperature inside the gearbox was reported to be unusually high and the life of transmission oil quality deteriorated drastically, Temperature increment caused the large gap between the bearing outer diameter and the transmission housing. Large gap made the gear shaft assembly move intermittently and impact each other. The tighter control of the assembly gap allowed the rotating shafts smoothly and reduced the gear rattle noise even in the high temperature range.
-
This study introduces the basic concepts of the vibration reducing methods and presents a case study of 'A' apartment construction site which located nearby railroad. The site is only 60m away from the railroad. Therefor much noise and vibration damages could be expected during train or any other transportation's passing. Especially, the first and second floor may suffer much vibration with the low frequency radiation noise from the walls and floors. This study estimates the noise level of indoor area by measuring the vibration of indoor walls and floors. From this result, vibration barrier, as a method to reduce the noise level which exceeds proper standard value, was attempted to protect vibration transmit from the railroad.
-
Dynamic response of ground due to train loads is analyzed. A numerical procedure based on finite element method is used to solve two-dimensional ground response. Dynamic train loads assumed in analysis is the point acceleration on train rail with magnitude of 2330 gal and thickness of surface of soil layer assumed is 60cm. In order to consider the effect of acceleration point, dynamic responses such as response acceleration and displacement are computed as a function of distance from acceleration point on rail. In addition, simple methods which reduce dynamic effects on ground are also proposed.
-
현재 국내에서는 신항만건설. 경부고속철도 건설, 기존고속도로 신설 및 확장공사 등 대형 국책공사와 도심지 내에서의 아파트부지조성, 고층건물신축, 우회도로, 지하차도, 지하철건설 등 중소형 공사가 증가되고 있으며 이러한 대소형 공사 시에 발생하는 건설소음ㆍ진동은 계획단계에서부터 합리적인 기준설정과 충분한 환경영향평가가 이루어져야겠으며 또한 이러한 평가결과가 공사에 잘 반영되어야 할 것이다. (중략)
-
생산 현장의 진동환경은 부품생산활동과 관련된 공정변수중 대표적인 것으로 기계 부품 생산의 품질 및 생산품의 불량률에 큰 영향을 미치며 또한 주변으로 전파된 진동은 우수한 진동환경을 요하는 다른 생산장비에 나쁜 영향을 미치기도 한다. 본 연구의 대상은 공장의 이전으로 인한 환경변화에 의해 발생한 타공형 방음벽 생산 프레스의 진동을 제어하기 위해 바닥의 진동가속도 레벨을 측정하고 DIN 5140에 제시된 기준에 적합하도록 방진 시스템을 설계하였으며 그 결과 방진전과 비교하여 약 20 ㏈ 가량의 바닥 진동 가속도 레벨이 감소하였다.
-
In this paper, damping behavior of steel fiber reinforced concrete(SFRC) beams by experimental and numerical method is discussed. Because of its improved ability to dissipate energy, SFRC has a better damping behavior than that of reinforced concrete(RC). Damping behavior is influenced by longitudinal reinforcement ratio, volume and type of steel fiber, strength of concrete and the stress level. Damping in the SFRC beams has been evaluated from dynamic experimental test data at various levels of cracked states in the beams. A FEM program(TICAL) has been developed based on the relationships between curvature and damping. It is observed for SFRC beams with 0.44% of tensile reinforcement steel that approximate 5% to 35% was relatively increased in the damping ratio generally depending on the load level.
-
An experimental study was performed for two types of co-axial cylindrical shell structures in order to establish the relationship between in-air dynamic characteristics and in-water ones and to observe hydrodynamic mass effects on their mode shapes when submerged. The outer cylinders are prepared with two kinds to get more insights on the fluid-structure interaction phenomena: one is flexible, which means that the outer cylinder has almost same stiffness as the inner one, and the other is a rigid one whose stiffness is more than ten times of the inner one's(it might be regarded as the scaled-down model of the reactor internals). The finite element. analyses were also implemented to support the experimental results. The results show that the natural frequencies of a co-axial cylindrical shell structure in water are remarkably lower than those in air due to the fluid mass effects. In case of the flexible-to-flexible cylinders, there exist in-phase and out-of-phase mode shapes and they are affected by the annular gap between the. co-axial cylinders. For the in-phase mode the in-water natural frequency decreases exponentially as the gap increases, while it slightly increases in case of the out-of-phase mode due to the squeezing effect of the gap fluid. In the flexible-to-rigid case, the normalized natural frequency(in-water frequency/in-air one) of the inner cylinder(core barrel model) ranges between in-phase and out-of-phase mode frequencies of the flexible-to-flexible co-axial cylindrical structure having identical dimensions. Also the normalized natural frequency of the inner cylinder of the flexible-to-rigid one moves from near of the in-phase mode frequency into the out-of-phase mode value of the flexible-to-flexible case as circumferential mode number(n) increases.
-
In this study, a fluid/structure coupled analysis system using computational fluid dynamics and computational structural dynamics has been developed. The unsteady flow fields are predicted using unstructured Euler code. Coupled time-integration method (CTIM) was applied to computer simulation of the flow-induced vibration phenomena. To investigate the interaction effect of shock motions, 2-DOF airfoil systems have been studied in the subsonic and transonic flow region. Also, aeroelastic analyses for the airfoil with an arbitrary object are performed to show the analysis capability and interference effects for the complex geometries. The present results show the flutter stabilities and characteristics of aeroelastic responses with moving shock effects.
-
Two-phase cross-flow exists in many shell-tube heat exchangers such as steam generators, condensers and reboilers. An understanding of flow-induced vibration excitation mechanism is necessary to avoid problems due to excessive tube vibration. This paper presents the results of a series of experiments done on tube bundles of different geometries subjected to two-phase cross-flow simulated by air-water mixtures. Normal(30
$^{\circ}$ ) and rotated (60$^{\circ}$ )triangular, and normal(90$^{\circ}$ ) and rotated (45$^{\circ}$ ) square tube bundle configurations of pitch-to-diameter ratio of 1.2 to 1.5 were tested over a range of mass fluxes from 0 to 1,000kg/$m^2$ ㆍ s and void fraction from 0 to 100%. The effects of tube bundle geometry on vibration excitation mechanism such as fluidelastic instability and random turbulence, and on dynamic parameters such as damping and hydrodynamic mass are discussed. A lower pitch-to-diameter results in a higher hydrodynamic mass. The effect of tube bundle configurations on damping and random turbulence excitation is minor. The effect of pitch-to-diameter on the fluidelastic instability, however, is significant. -
The 84m discharge line of moisture separator reheater(MSR) in Kori-2 had been suffered by excessive vibration from the beginning of power generation. In 1993, a complementary measure was taken to reduce the vibration level by adding several supports in the MSR pipeline. However, the piping vibration was beyond the allowable limit and an appropriate countermeasure was required to prevent the fatigue failure of the pipeline from the abnormal vibration. In this study, the vibrational characteristics of MSR pipeline and the countermeasure for abnormal vibration was investigated. Among the several vibration reduction methods, piping layout change by smoothing the pipeline was applied to the MSR pipeline in Kori-2. Applying the countermeasure, the vibration level was found to dramatically reduce from 17cm/sec to l.0cm/sec at the full-power operation condition.
-
While a rotating inner cylinder executes a periodic translational motion in concentric annulus, the vibration of the rotating inner cylinder is induced by fluid-dynamic forces acting on the cylinder. In the previous study related to journal bearing, the unsteady viscous flow in the annulus and the fluid-dynamic forces were evaluated based on a numerical approach. Considering the dynamic-characteristics of unsteady viscous flow, an approximate analytical method has been developed for estimating added mass, viscous damping and fluid-stiffness coefficients. For the study of flow-induced vibrations and related instabilities, it is of interest to separate the coefficients from the fluid-dynamic forces. The added-mass and viscous damping coefficients for very narrow annular configurations, as journal bearing. can be approximated by considering the gap ratio to the radius of inner cylinder, while the fluid-stiffness coefficient is related to the Reynolds number, the oscillatory Reynolds number and the gap ratio.
-
This paper deals with a method to predict the flying state of the head slider in a optical disk drive(ODD). The Dual Solver based on the Quasi-Newton method and the Newton method has been developed to simulate the steady-state flying conditions. The numerical results show the effectiveness and reliability of this new solver.
-
A dynamic vibration absorber(DVA) is developed to reduce the excessive focusing vibration of an optical disc drive(ODD) originated from the resonance of an wobble disc. We design the material properties of the DVA by FEM model such as Young's modules, damping coefficient, shapes and dimensions, analyze its dynamic characteristics and provide its design guide line for suppressing the vibration of an optical disc drive. To examine the performance. of the DVA, the vibration of the wobble disc and the feeding system is measured by using a laser vibrometer and the noise level is checked by using microphone. The result shows that the proposed DVA reduces the vibration and. the noise in an optical disc drive.
-
In order to modify flexible mode frequencies, finite element analysis is applied for a lens-holder in pick-up actuator. Several design parameters like shape and local dimension of a lens-holder were selected adequately and sensitivities of the design variables for vibration modes were obtained by FE analysis and this result was used for updating FE model. A sensitivity matrix between the natural frequencies and the design variables was calculated by finite difference method. By comparing the calculated natural frequencies with target frequencies, modification of the design variables was acquired and used for improving FE model. Calculated natural frequencies after several iterations by FE analysis coincided with target frequencies and the errors between them were minimized.
-
For higher recording density in optical data storage, near field optics is being actively researched as one of the promising alternatives. But the tight assembling tolerance in NFR is one of big barriers to overcome for the realization of it. In this paper, the tolerances in assembling optic components of NFR system are analyzed. Some of key tolerances can be loosened by the optimization of objective lens design. But one of them become too tight by the optimization and should be controlled by other means. One of possible methods to control the tolerance is discussed.
-
Applying a general coupled lateral and torsional vibration finite element model of gear pair element this paper intends to look into in detail the coupled lateral and torsional vibration characteristics in a turbo-chiller rotor bearing system, having a bull-pinion speed increasing gear. Investigations have been carried out systematically by comparing the uncoupled and coupled analyses natural vibration frequencies and their mode shapes upon varying the gear mesh stiffness, and also by comparing the strain energies of lateral and torsional vibration modes. Results have shown that some modes may have coupled lateral and torsional mode characteristics as the gear mesh stiffness increases over a certain value, and moreover that their associated dominant modes may be different from their initial modes, i.e., the dominant mode changes from an initial torsional one to a lateral one or from an initial lateral one to a torsional one.
-
A 3-dimentional finite element model for vibration analysis of steam-turbine blade groups is presented, employing the 3-dimentional incompatible brick element with 8 nodes. The skew coordinate system is introduced in the model for considering multi-axis symmetry and specialty of displacement constrain condition of blade groups. Vibration characteristics of blade groups are analyzed, and compared with experimental results.
-
This study was performed to evaluate the dynamic behavior of turbo pump unit. The acceptable separate margin of 1st critical speed was obtained by the use of elastic-ring inserted ball bearing, while the poor separate margin of 1
$\^$ st/ critical speed was appeared in the case without the elastic-ring. In addition, the results show that the stiffness and damping of plain seals gain more separate margin of 2nd critical speed. However the wear or the failure of seals could reduce the 2$\^$ nd/ critical speeds near the operating speed. -
As related to rotordynamics, dynamic characteristics of the wear ring seal in high pressure multi-stage pump is calculated in the cases of labyrinth, damper and helically grooved types. The. results show that the labyrinth seal type has superior performance in the view point of leakage. However, in terms of rotordynamics view point, the damper seal type gains acceptable separate margin in critical speed range, while it has slightly inferior leakage performance compared to labyrinth seal type.
-
Todays, according to development of traffics, there are so many tunnels around us. Tunnels are used for trains, subway trains, cars, etc. Especially for subway, all of its routes are tunnels. So the noise of the subway train cannot radiated out of the station and the noise level in the station and train cabin is so high. There are some methods to reduce this noise and one of them is using absorbing materials. But the area of the tunnel and station is very large, so it is important to determine the effective position and amount of absorbing materials before attaching them. In this study, we studied the effect of sound absorbing materials in the tunnel using boundary element method. We applied BEM for general boundary conditions. With BEM calculations, we found the effect of absorbing materials and effective positions for the subway tunnel and station.
-
An experimental model of the advanced mixing control in the parallel supersonic-subsonic mixing jet (M
$_1$ =1.78 and M$_2$ =0.30) is numerically simulated. An oscillating wall boundary condition is used as the modeling of a wall cavity for mixing enhancement. The obtained pitot pressure distributions along cross sections at the developing region of the turbulent jets are validated from the good agreement with equivalent experimental data. The similarity solution of dimensional analysis also coincides with this numerical result at the self-similar region sufficiently far from the jet exit. -
In order to study noise barriers of complex shapes and to assess their efficiency, precise prediction model is required. For instance, geometrical approaches cannot deal with complex diffraction effects. So that in this paper, the time domain numerical computation method(Computational Aeroacoustics method) is applied to estimate noise reduction by diffraction and finite impedance condition. The CAA method can be used to calculate exactly the pressure of complex barrier shape with different impedance condition, such as T-shape, cylindrical edge and multi-edge noise barriers.
-
LES formulation was applied to simulate the flow fields around rotating fan blades tested by DLR. The turbulent flows around fan blade rotating with 500 RPM were simulated and the far-field noise was exactly computed by using the Focus Williams and Hawkings equation with an inclusion of quadrapole source formulation. The dipole noise computed at the far-field by predicted drag and lift forces at steady state was in good agreement with experimental data and the dipole source was also found to be the major factor than other sound sources from unsteady calculation.
-
The self-noise from blade cascade at off-design points mainly comes from separated boundary layer and vortex sheddings, and is also dependent on blade shape. If the incidence angle to the cascade increases, the stalling in blades may occur and the noise level increases significantly. The hybrid method using acoustic analogy was employed to compute the far-field noise spectra and directivity patterns from the separated vortex shedding at off-design points of the cascade of impeller. This paper is compared with the experimental data of a stationary cascade in the same conditions. The simulated result is in excellent .agreement with the measured data except th slight under-prediction near the maximum radiation angle for a dipole sound.
-
If rotating machinery have a fault, we can detect it using vibration or noise signals. However some maintenance engineers who doesn't have expert knowledge, needs the help of vibration experts for diagnosing rotating machinery. But qualified experts are rare, therefore we have been developed the case based reasoning (CBR) system which is able to manipulate the past experiences of vibration diagnosis experts. In the CBR system, the maintenance engineers can retrieve too information from previous cases which are most similar to new problem and they can solve new problem using solutions from the previous cases. In this paper, we propose a new method which is the case retrieval of CBR system using Petri net and we also applied it to diagnosis for electric motors as a practical problem.
-
A method for accurate measurement of the contact force in the current collection system of the high-speed railway is developed. In order to measure the contact force with minimal modifications to the pantograph, strain gauges are attached to the bottom of the contact strip. An algorithm for deriving the magnitude and stagger of the contact force from the bending strain measurements is devised. For the sample pantograph, the static contact forces are measured to within
${\pm}$ 5 % error for the magnitude and${\pm}$ 2cm error for the stagger. For dynamic contact force measurement, it is found that the contact strip can the regarded as a rigid body for the contact frequency of less than 15 ㎐. -
In this paper, the identification of connections for a vibration system has been presented using FRF-based substructural sensitivity analysis. The substructural design sensitivity formula is derived and plugged into a commercial optimization program, MATLAB, to identify connection stiffness of an air-conditioner system of passenger car. The air-conditioner system, composed of a compressor and a bracket is analyzed by using FRF-based substructural(FBS) method. To obtain the FRFs, FE model is built for the bracket, and the impact hammer test is performed for the compressor. Obtained FRFs are combined to calculate the reaction force at the connection point and the system response. Connection element properties are determined by minimizing the difference between a target FRF and calculated one. It is shown that the proposed identification method is effective even for a real problem.
-
This paper is basic study of seismic response analysis for the large scaled structures subjected to seismic loading. The authors propose seismic response analysis algorithm for the multi-story structures, which are subjected to ground acceleration. This analysis method is derived from an combination of the transfer stiffness coefficient method(TSCM) and Newmark method. Numerical computation is performed for simple multi-story structures acting on an arbitrary ground acceleration. Numerical results by the TSCM which is applied to the various strong ground motion are compared with results by central difference method and Runge- Kutta method.
-
필자는 소음진동공학회가 품질기술원으로부터 ISO/TC108 기계진동 및 충격(Mechanical Vibration and Shock) 간사기관업무를 위탁 받은 후부터 SC6 진동 및 충격 발생시스템(Vibration and Shock Generating Systems)에 대한 한국측 위원으로 일을 해왔다. (중략)
-
ISO 11342 classifies flexible rotors in accordance with their balancing requirements and establishes methods of assessment of residual unbalance. This International Standard also shows how criteria for use in the balancing facility may be derived from either vibration limits specified for the assembled and installed machine or unbalance limits specified for the rotor. If such limits are not available, this standard shows how they may be derived from ISO 10816 and ISO 7919 if desired in terms of vibration, or from ISO 1940- 1 if desired in terms of permissible residual balance. This International Standard also presents methods for adapting the criteria of ISO 1940- 1 to flexible rotors.
-
ISO TC 108/SC 2 산하에 이미 제정된 24 개의 관련 규격이 있으며, 그 중에 현재 4 개의 규격이 개정 심의 중에 있다. 본 논문에서는 FDIS(Final Draft International Standard) 개정 단계에 있는 육상용 증기 터빈 발전기 세트의 회전축 진동 및 비회전부 진동에 관련한 두 규격(ISO 7919-2:1996, ISO 10816-2:1996) 과 2000년 12월 15일자로 개정 완료된 선박 거주구역 및 작업구역의 진동에 관한 규격(ISO 6954:2000)을 개정 전 규격과 비교 설명 하고자 한다. (중략)
-
인체에 영향을 미치는 진동을 분류하는데 가장 중요한 기준은 주파수이다. ISO의 인체진동관련 규격에서는 인체에 영향을 미치는 거동을 저주파수 운동(0.63Hz이하)과 진동(1~80Hz)으로 나누고 있다[1]. ISO 2631에서는 주파수별로 인체에 미치는 영향을 그림1과 같이 가중치로 정의하여 제시하고 있다. 저주파수 영역의 운동은 외부 거동(주로 수평방향)에 대하여 자세를 유지하기 위해 힘Tm게 되므로 물리적인 피로감을 줄 뿐만 아니라 'Motion sickness'란 증상을 유발한다.(중략)
-
The sources of wayside noise for the high speed train are the aerodynamic noise, rolling noise and power unit noise. One of the best ways to control the wayside noise is to analysis the noise level. In this paper, we measure the wayside noise and the vibration of the rail/sleeper for Korean Train Express (KTX) and compare with the results for the conventional train. The measurement results for KTX show that the characteristics of the noise and vibration are different from the conventional train and the rolling noise and power unit noise are the major sources.
-
The more sophisticated patterns of propagation model is presented in this paper, which includes three different source characteristics. The spherical, cosine and dipole radiation characteristics compared and sound event level and the maximum sound level are calculated by experiment and calculation. It is shown that patterns of propagation has dipole characteristics for low speed range(below about 150km/h) at electric multiple system. We know that push-pull high speed system(maximum speed: 300km/h) has cosine characteristics of noise propagation. For this purpose, We conduct the experiment of noise and know the empirical formula of noise level and radiation coefficient K. This model of simulation is conducted through point source array model at wheel/rail contact point by using program and experimental formula. We can guess prediction of profile, flat and wear of wheel by above modeling in near field.
-
Railroad noise is one of the main causes of environmental impact. Whenever a new railroad line is planned or a housing project near an existing railroad is proposed, an estimate of the relevant noise levels is usually required. For this, it is necessary to quantify those parameters that affect the railroad noise. This paper deals with an estimation of railroad noise using soundproof tunnel in a high-rise apartment building
-
Cabin noise reduction in maglev trains developed by KIMM is studied. Based on the measurements of cabin noise and acceleration levels during running and zero speed conditions, dominant noise sources are identified. After spectra characteristics of noise sources is investigated, efficient noise reducing methods are studied such as STL increasement of floor panels, sealing, and absorption treatment. It is found that the most important noise sources are VVVF inverter and SLIM in running condition. Since the noise sources are under the cabin floor, complete sealing and high STL of the floor panel are shown to be the most crucial factors in noise reduction. After polyurethan form (50t) is added for more sound absorption and sealing treatment, the cabin noise is reduced by 3-4 ㏈.
-
In this study, the improvement work to reduce the steering wheel vibration of a forklift truck is performed. The forklift truck newly developed possesses a trans-axle type power train to achieve a compact and low-price design. The forklift truck is directly subjected to a high-level engine vibration through hard mounted trans-axle housing. The engine vibration shakes the whole system of the forklift truck, and then a high level local vibration of steering wheel could not be avoided. As the results, the vibration source and path mechanisms are experimentally identified and then an improvement design is proposed to minimize the steering wheel vibration.
-
It is necessary to design th anti-vibration system of precision machinery for a sound operation and a quality assurance. However, in general. the allowable vibration limit is not well known. In the paper, the vibration criteria for foundation of vibration sensitive machinery is proposed and anti-vibration system is designed by using vibration measurement results of foundation. Also, the F.E. analysis is performed to verify the effectiveness of a designed anti-vibration system and to determine allowable dynamic load of machinery
-
In order that precision equipment using high precision industrial operate normally. vibration criteria of expected area that equipment be set up is micrometer level. that method is a trust design for apply to in field, when there attend to quantifiable method. Hence, semi -empirical method that using on the basis of experimental data about undefined information (properities of vibration source, dynamic properities of structure, etc.,) for prediction of vibration response make the use of dynamic structure design of semiconductor & TFT-LCD in the inside and outside country. Like this, for doing an optimal design of dynamic about structure, it is best important to get trust data that apply to semi-empirical method that is method of prediction vibration level. In this paper, on the basis of experimental data which was offered by a manufacturing company Of precisin equipment that plan to set up in semiconductor factory, we predicted vibration response on expected area that equipment be set up.
-
This paper deals with the free vibrations curved beams with elastic springs. Taking into account the effects of rotatory inertia and shear deformation, differential equations governing the free vibrations of such beams are derived, in which each elastic spring is modeled as a discrete Winkler foundation with very short longitudinal length. Differential equations are solved numerically to calculate natural frequencies and mode shapes. In numerical examples, the circular, parabolic, sinusoidal and elliptic curved members are considered. The parametric studies are conducted and the lowest four frequency parameters are reported in tables and figures as the non-dimensional fonns. Also the typical mode shapes are presented.
-
The study about a drainpipe of water closet was performed as reduction of drainage noise for water closet. The Drainage noise is composed two characteristics. One is Low frequency noise and the other is high frequency noise. Low frequency noise is dominant in the first stage and high frequency noise is dominant in the last stage. This is due to water splashing and that is caused by formation of chamber pot. In this experiment, for the purpose for reducing the noise, we choose the hollow rubber pipe element. As a result, we reduced drainage noise about 11㏈A.
-
This paper present the results of finite element analysis to examine the sloshing characteristics of the cylindrical and rectangular tank partially fluid-filled. The sloshing characteristic for the existence and the non-existence of the baffle are investigated and the results compared with the references. For the rectangular tank, the vertical displacements are used to study of the sloshing characteristics. But for the cylindrical tank, the damping factors obtained from the vertical displacements of free surface with the depth of ring baffle are usedto study of the sloshing characteristics. The adaptive meshing method in the ABAQUS 5.8/Explicit is used for the sloshing analysis.
-
백색잡음 불규칙 과정으로 모델링된 난류형태의 유체운동에 의하여 가진되는 비선형 시스템의 특성과 제어기법에 대해 연구하였다. 고려된 물리적인 모델은 주질량과 끝단 집중질량을 갖는 보형태의 구조물이다. 그 지배방정식은 확률론적 관점에서 F-P-K 접근법으로 유도되었고, 비선형 해석법으로 Gaussian Closure방법을 이용하였다. 비선형 시스템의 제어기법으로는 슬라이딩 모드 제어기를 최초로 확률영역에서 설계하고 그 효과를 확률영역 및 시간영역에서 고찰하였다.
-
The supersonic flutter analysis of cylindrical composite panels subject to thermal stresses has been performed using layerwise nonlinear finite elements. The geometric nonlinear finite elements of cylindrical shells are formulated using hamilton's principle with von Karman strain-displacement relationship. Hans Krumhaar's modified supersonic piston theory is appled to calculate aerodynamic loads for the panel flutter analysis. The present results show that the critical dynamic pressure of cylindrical panels under compressive thermal stresses can be dramatically reduced. The margin of aerothermoelastic stability considering thermal and aerodynamic coupling should be verified in the structural design of launch vehicles and high speed aircrafts.
-
Static and oscillatory loss of stability of composite pipes conveying fluid is investigated. The theory of thin walled beams is applied and transverse shear, rotary inertia, primary and secondary warping effects are incorporated. The governing equations and the associated boundary conditions are derived through Hamilton's variational principle. The governing equations and the associated boundary conditions are transferred to eigenvalues problem which provides the information about the dynamic characteristics of the system. Numerical analysis is performed by using extended Gelerkin method. Critical velocity of fluid is investigated by increasing fiber angle and mass ratio of fluid to pipe including fluid.
-
Structural acoustic modification method based on the structural mobility analysis is applied to reduce the structure-borne noise radiated from hard disk drive system. Sound intensity techniques and ODS(Operational Deflection Shape) techniques are also used in order to provide the structural acoustic information for the mobility modification. The sound intensity is for the acoustic visualization of the noise source locations, and the ODS is for the visualization of the vibration pattern and its dynamic characteristics of the noise sources. Using visualization information of sound and vibration, local structural input mobility is reduced in the frequency band of interest by designing asymmetrical wave-stringer structure in the wave-number domain as well as frequency domain. The overall sound pressure level is reduced by 4dB and its controlled sound power radiated from the disk drive is proved to under 2.8Bel in idle-spinning mode and 3.1 Bel in random-seeking mode, which are the lowest noise levels in the hard disk drive industry.
-
This paper presents the fabrication and testing results of a dual stage microactuator system for fine positioning of magnetic heads in hard disk drives. An electrostatic rotary microactuator was newly designed and fabricated. The microactuator was integrated into the head gimbal assembly of a disk drive system and its dynamic characteristics were investigated. Experimental results show that natural frequency and voltage gain of the microactuator are 4.3 KHz and 25 nm/V and the dual stage microactuator system achieves the tracking accuracy of 30 nm.
-
The flying height of contact slider is determined by vertical and pitching motions of slider. This paper performed the computer simulation for flying height change of contact slider. It is changed by many parameters, contact stiffness, contact damping, air bearing stiffness ratio, a location of mass center, and so on. Computer simulation is performed for knowing for what change of these parameters influences in flying height of contact slider. Disk surface is modeled in harmonic wave with from 10㎑ to 600㎑. Tri-pad slider is modeled in that contact slider has 2-DOF motion (vertical motion, pitching motion). Tri-pad contact slider is analyzed by numerical analysis method in computer simulation.
-
The experimental characterization of hydrodynamic bearing spindle motor is performed for the practical implementation of high-performance hard disk drive system. Firstly, the design concept of hydrodynamic bearing for the disk drive system is addressed including the herringbone grooved journal bearing, the spiral grooved thrust bearing, capillary seal design, and the viscous pumping of fluid. Secondly, the experimental evaluation is performed for the disk drive system in which the hydrodynamic bearing spindle motor is implemented and its dynamic performances are compared with conventional ball-bearing spindle motor. The key parameters include NRRO(Non Repeatable Run-Out), disk dynamics, acoustics, and resultant PES (Position Error Signal). Finally, the external gyro-exciting test results including 200k CSS(Continuous Start-Stop) on three angular attitudes(0,90, 180 degree) are presented in order to verify the practical reliability of disk drive system subject to the gyro-motion of hydrodynamic bearing spindle motor.
-
This paper deals with the design of oil-tree motor-driven two-stage centrifugal compressor supported by air-lubricated multi-leaf foil bearings. The design of this compressor is performed, based upon prediction of critical speeds, load capacity, and stability. It is demonstrated in this paper that multi-leaf foil bearings can be adopted to satisfactorily support this centrifugal compressor.
-
This paper provides a stability analysis of the transverse vibration of a spinning disk under the torque fluctuation from a permanent magnetic motor. An analytical model has been formulated for a flexible annular disk with its spinning velocity varying harmonically with the same frequency as the cogging torque. A perturbation method based on multiple time scales is applied to perform the stability analysis. Based on expressions for the amplitude and frequency of the parametric excitation, stability boundaries are determined in terms of a nominal spindle velocity, the least common multiple of poles and slots, the magnitude of torque fluctuation and the modal characteristics of. the disk. The stability diagrams predicted by perturbation have been verified numerically using the Floquet theory, which is in good agreement. In conclusion, the fluctuation in spinning velocity is found to affect the stability of the transverse vibration of a rotating disks. The results of this work can be applied to high precision spindle systems such as computer storage systems.
-
Nonlinear dynamic equation of a 4-axis rigid rotor supported by two an-isotropic magnetic bearings is derived via Hamilton's principle. It is transformed to a state-space form for the standard Η
$_{\infty}$ control problem. we present a robust Η$_{\infty}$ control design methods of continuous and discrete LMI-based approaches and improve performance using loopshaping. -
Axial fans are widely used in heavy machines due to their ability to produce high cooling of engines. At the same time. the noise generated by these fans causes or serious problems. This work is concerned with the low noise technique of discrete. The prediction model. which allowed the calculation of acoustic pressure at the frequency and it's harmonics, has been developed by Farrasat and the Helmholtz-Kir. The newly developed Helmholtz-Kirchhoff BEM for thin body is used to calculate the sound field of the fan that is located in a engine room. To calculate the unsteady resultant force over blade. Time-Marching Free-Wake Method are used. The fan noise of fan sys unsymmetric engine-room is predicted. In this paper. the discussion is confined to and discrete noise of axial fan and front Part of engine room in heavy equipments.
-
Micro fans of randomly swept-blades were designed to provide C.P.U. in a personal computer with effective cooling in a very quiet mode. The proto--type axial micro-fans machined by a laser sintering machine were tested against manufactured products by comparing the performance and overall sound pressure level with spectral measurements in an environment suggested by ASHRAE and ANSI standards. The predicted OSPLs and directivity patterns of fans by iDesignFan software were in good agreements with measured data. The newly introduced fans of randomly swept-blades were proved to provide a very promising mode of low noise at small loading conditions.
-
An axial fan design code, called iDesignFan
$^{TM}$ , was developed. In this code, three major loss models were used to predicted the aerodynamic performance of a fan. The overall sound pressure level, predicted from steady blade loading, is also used as an input parameter from the third loop of the designing process to acquire most silent fan for the given aerodynamic performance parameters. With this kind of inverse design concept used in this code, the period of designing a fan, which has given aerodynamic performance with minimal acoustic noise, is significantly shortened. The experimental results of a prototype fan, designed by this code, showed that aerodynamic and acoustic performance of an axial fan is reasonably well predicted. Thus, one can design/develop an axial fan in a short time by using the code.e. -
Noise reduction has become a major issue of the manufacturing industry. This paper describes the reduction of noise and vibration of rotary compressors. Empirical design for the present strap of the accumulator has been considered to be sufficient for the constraint of the accumulator resonance modes without thorough study. Recently, however, some researchers found out that the accumulator contributes considerably to the sound propagation. In this paper, the contribution of accumulator to the noise propagation is investigated through sound measuring experiments by checking the directivity of the noise. And, experimental modal analysis results show that frequencies of some resonance modes of the accumulator coincide with the highest peaks on sound spectrum. To demonstrate the reason for those resonance modes, a finite element analysis is conducted. Normal mode analysis of the finite element model of the rotary compressor shows the mechanism of the accumulator resonance modes.
-
We develop a new method of simultaneous optimization of trajectory and shape of redundant flexible manipulators for collision-free utilizing the B-spline function and a mathematical programming method We adopt an approximate flexible manipulator model which consists of rigid bar elements and spring elements. We use B-spline function for determining the approximate trajectory and the expressions of the outline of obstacles. The used total performance index consists of 2 performance indices. The first is the driving energy, and the second is the trajectory deviation which is caused by the approximate modeling for the flexible manipulator. We design optimal collision-free trajectory of flexible manipulators by searching optimum positions of the control points for B-spline approximation which minimize the performance index subject to constraint condition for collision-free. Some examinations through numerical examples show the effectiveness of the method
-
위성체의 태양전지판과 안테나와 같은 구조물은 발사시 체적을 최소화하기 위하여 설정궤도에 도달하기 전까지 접혀진 상태로 운반되며, 설정궤도에 도달 후 고유의 임무를 수행하기 위하여 안테나, 태양전지판 및 로보트 팔과 같은 이차 부착물의 전개 작업을 수행한다. 이러한 작업은 위성체 및 발사체의 고유임무를 수행하는데 매우 중요한 작업이며, 이 작업의 성공 유무가 우주비행체 임무의 성패를 좌우한다.
-
The Frequency Response Function(FRF)s of FE Model reduced by SEREP methods accurately estimate the full model at resonance frequencies, However these FRFs are not accurate at antiresonance frequencies, Additionally, the truncation errors may he significant in the reduction mode1. So this paper considers the possibility of SERFP method through a numerical method to preserve dynamic behavior at antiresonance and appliers the static or dynamic compensation methods for truncation errors to the reduction model. This compensated reduction model is redesigned for pole-zero cancellation methods the objective of reducing a resonance frequency.
-
It is well known that there are two experimental errors on acoustic decay measurements. One is due to the influence of the band pass filter the other one is that of an averaging device. In this paper the influence of the filter is in detail investigated. To minimize the influence of filter, the product of the filter bandwidth Β (3㏈ bandwidth) and the reverberation time T
$\sub$ 60/ of the room under test is at least 16. Moreover, if the initial part of an acoustic decay curve is important, the strong requirement, i.e. BT$\sub$ 60/> 64, must be satisfied. In this paper, the wavelet filter bank instead of the band pass filter bank is applied to obtain an acoustic decay curve. As results, the influence of filter is reduced and then the value of BT$\sub$ 60/ required for obtaining an acceptable decay curve is at least 4. The strong requirement for the initial part of a decay curve is also replaced by the BT$\sub$ 60/> 16 instead of BT$\sub$ 60/> 64. -
This paper describes an implementation of inverse filter using SVD in order to recover the input in multi-channel system. The matrix formulation in SISO system is extended to MIMO system. In time and frequency domain we investigates the inversion of minimum phase system and non-minimum phase system. To execute an effective inversion of non-minimum phase system, SVD is introduced. First of all we computes singular values of system matrix and then investigates the phase property of system. In case of overall system is non-minimum phase, system matrix has one (or more) very small singular value(s). The very small singular value(s) carries information about phase properties of system. Using this property, approximate inverse filter of overall system is founded. The numerical simulation shows potentials in use of the inverse filter.
-
In beamforming method, source positions are predicted by MUSIC (Multiple Signal Classification) power method and composite sound fields can then be decomposed into each partial field by beamforming, detenninistically without restriction of the distance between reference microphones and sources. However, reference microphone array shape is important in both MUSIC and beamforming method. Thus the present paper describes the effect of the reference microphone array shape.
-
A numerical investigation on nonlinear oscillations of gas in an axisymmetric resonant tube is presented. When a tube is oscillated at a resonant frequency, acoustic variables such as density, velocity, and pressure undergo very large perturbation, often described as nonlinear oscillation. In order to analyze these phenomena, axisymmetric 2-D nonlinear governing equations have been derived and solved numerically. Numerical simulations were accomplished for cylindrical, conical, and 1/2 cosine-shape tubes, which have same volume and length. For conical and 1/2 cosine-shape tubes, very large variation of pressures can be induced without shock formation except the cylindrical tube. In addition, the results well agree to those of 1-D simple model analysis.
-
Evaluation of Dynamic Stability of KHSR Bridges Using Train/Track/Bridge Interaction Analysis MethodThis paper represents the results carried out to determine the dynamic response characteristics of Korea High Speed Rail(KHSR) bridges. The responses of the KHSR bridges subjected to the moving train loading are obtained through the simplified method for the 2-dimensional train/track/bridge interaction analysis in which the eccentricity of axle loads and the effect of the torsional forces acting on the bridge are included for the more accurate train/track/bridge interaction analysis. The results of the analyses are compared with the field test data to verify the performance of the 2-dimensional train/track/bridge interaction analysis method.
-
In this study, the train-induced vibration was measured at many locations at/around the actual service lines and the data base was constructed using the measurement results. The characteristics of train induced ground vibration was categorized and the empirical ground vibration estimating equations were developed. On the ground area (level grounds, embankments, cut sections), the vibration estimating equations were developed in terms of ground vibration level which was related with the distance from the source. Especially for the cut section areas, the vibration levels were expressed with the vibration receiving point expressed by the ratio of vertical distance to horizontal distance(V/H) from the source. As a result, when V/H is 0.96, the vibration estimating equation gives a minimum vibration level.
-
열차주행시 열차의 이동축중에 의한 제도구조물의 동적거동은 열차의 동특성과 열차속도, 궤도의 유형 및 제도재료의 물성치에 따라 변하며 차량과 궤도의 상호작용에 따라 변하게 된다.(중략)
-
Recently. development of a subway as a public transport has been increased rapidly. Therefore, large noise, which induced from vehicle itself as well as frictions between rails and train, may inflict a considerable damage to the adjacent structure and cause discomfort to neighboring residents. Nevertheless, adequate design guidelines to reduce outdoor noise are not yet established. The present work carried out a survey on the influence of outdoor subway noise using questionnaires. Also or noise measurements levels in those are as were performed.
-
This study is to propose an analyzing method of road traffic noise in apartment sites using computer simulation program. The evaluation method used in this study is to calculate "Site Equivalent Noise Level". It will be possible to set up effective sound proof system with calculation of "The Number of Houses Exceeding Standard Noise Level".
-
Before building houses or apartments, we need to predict noise propagation to eliminate possible noise problems to residents. However, we do not try to predict noise propagation during estimation of noise effect for the developing area since we did not have a good mathematical model to predict noise level due to a traffic noise. In this article, an adequate mathematical model has been developed and proved to predict noise effect to living area due to a traffic noise.
-
A software for prediction of apartment noise level ihas been improved. The program is based on the ray tracing technique which has been widely used in the environmental noise analysis and prediction. Especially for prediction of environmental noise in apartment complex, this program is advanced in the graphics routine by bilinear interpolation. In this paper, we analyze the railway noise distribution in apartment environment and develop a 3D graphics routine for illustrating the noise level.
-
This paper describes the evaluation of noise influence of residental and boundary areas from power plant noise sources of 1200MW combined cycle power plant. Noise assessments are carried out by based on the ISO 3744, ISO 9613-1 and ISO 9613-2 to predict the noise distribution to satisfy the recommended noise level at specific locations and to calculate properly the octave noise power of main noise sources such as power transformers. air-intakes, stacks.
-
This study aims to suggest the basic data for structural safety assessment and design considering building dynamic characteristics. For this purpose, ambient vibration measurement was practiced after studying international standards dealing with vibration measurements such as ISO, DIN and so on. Various types of situation and condition which help search the building natural frequencies through the field measurements were proposed.
-
In this study, the room acoustics of a hall in Kimhae Performing Arts Center is discussed. The hall is designed as a multi-purpose hall. The reverberation time of the hall is varied by absorptive/reflective surfaces. A design method using both objective and subjective evaluations is investigated. As a result, the geometrical shape and the interior materials are determined.
-
기존의 타이어를 사용한 중량충격음에 대한 차음성능 평가방법의 타당성을 살펴보기 위하여 청감실험에 의한 감성적 반응결과와 L등급 및 Leq에 의한 평가 결과를 비교 분석하였다. 동일한 바닥충격원에 대한 분석결과 L등급평가 보다 Leq에 의한 평가가 청감실험의 반응에 잘 대응하는 것으로 나타났다. 또한, Zwicker parameters 중 Loudness와 Unbiased Annoyance는 청감실험과 가장 유사한 경향을 보였다.
-
The purpose of this study is to obtain the basic data of existing light-weight Drywall through the evaluation and analysis of the light-weight drywall in reverberation chamber and to improve sound insulation performance of drywalls. Sound transmission loss of the total 11 types were analyzed in each frequency a-third octave band and evaluated sound insulation performance for each frequency. From data by analysis and calculation, STC value plotted on STC contour. We found that the improved light-weight drywall specimens ⓑ, ⓒ and ⓖ were satisfied with the domestic standard of sound transmission loss.
-
This paper introduces new approaches attempted to evaluate quantitatively the effects of repeated shocks exposed to human. This attempt, by the members of ISO TC 108 / CS4, has been made to add a standardised draft of ISO 2631 Part 1 which covers newly the human response to repeated shocks. It contains the review of previous work related to shocks responses to human and suggests a mathematical model to predict the three-axis lumbar spine accelerations from the measured seat accelerations. The predicted accelerations are used to evaluate the vibration dose to the spine. The evaluated dose values are shown to enable the assessment of adverse health effects.
-
차량이 정지상태에서 출발하는 과정에서 클러치는 엔진의 동력을 구동축에 전달하는데, 이 순간 차량이 울컥거리는(clunking) 현상이 자주 나타난다. 이와 같이 발생한 충격과 진동은 작업자에게 불편함을 줄뿐만 아니라 차량의 상품가치를 떨어뜨리는 요인이 된다. (중략)
-
This paper introduces experimental results related to the vibration ride conditions that a korean male subject experienced in the railway trains and the express bus. Two types of railway train's, Samaulho and Mugunghwaho, and the express bus were chosen to measure how much the whole-body vibrations of the back, hip and feet are exposes to the subject. Measured vibration signals were analysed to assess the ride conditions quantitatively and qualitatively. Analysed results are illustrated to see how much typical public transportation systems in korea expose vibration to passengers.
-
본 논문은 머리진동 측정용 바이트 바의 동적 특성에 관한 연구이다. 머리진동의 관심주파수 영역은 0.5Hz~30Hz 범위의 주파수이며 기구학적 이론들을 이용하여 측정된 선형 가속도로부터 머리의 각각속도를 계산하는 과정을 소계한다. 본 논문에서는 9개의 선형가속도를 이용하여 각각속도를 구하는 방법에 대한 검증뿐 아니라 나아가 센서의 측정점의 Offset 영향을 고려한 이론식을 제시한다.
-
A transient T-F(time-frequency) signal processing technique is applied to a tilt drop and a linear shock test rigs for identification of shock characteristics of hard disk drive (HDD). The T-F technique essentially tracks the shock characteristics of pivot point response as well as head slap and lift-off phenomena. From the T-F analysis result, the shock characteristic in HDD is modeled by the two degree of freedom coupled-dynamic system, which consists of actuator arm and suspension. As shock designing tool, the maximax shock response spectrum is employed for prediction of shock performance. Finally, the shock control technique is tested with newly designed actuator arm and suspension. Experimental head slap test result shows that the shock performance is much higher with the new shockproof designed model than the current model
-
The dynamic behavior of slider is investigated using Dynamic Flying Height Tester(DFHT). The dependence of slider's dynamic fluctuation on disk velocity is measured, and a comparison is made with the computational result.
-
In this work, we propose a new type of HDD suspension featuring shape memory ally (SMA) actuator in order to prevent the contact between the slider and disk. The principal design parameters are obtained from the modal analysis using finite element analysis, and then the dynamic model is established to formulate the control scheme for Non-Contact Start/Stop mode drive. Subsequently, a robust Η
$_{\infty}$ , control algorithm is designed by integrating experimentally-obtained SMA actuator dynamics to the proposed suspension system. The controller is empirically realized and control results for different load/unload profiles are presented in time domain. In addition, the contact signal between the slider and disk is measured by the electrical resistance method.istance method. -
This paper investigated the dynamic performance of HDD disk-spindle system to reduce disk fluttering. Rocking frequencies of the disk-spindle system and radial NRRO are measured to escape the ball defect frequencies and to determine the relative optimal position of the disk in the motor. It was found that disk fluttering was reduced by increasing disk thickness, inserting viscoelastic material between the disk and the spacer and decreasing the gap between the disk and the base.
-
Viscous fluid damper is used for vibration isolation of piping system, presses, turbo-generator and other heavy industrial equipments, as well as seismic isolation of buildings structure. So dynamic characteristic of viscous fluid damper is very important. This paper presents the result of the study of dynamic characteristic of viscous fluid damper. And the force-displacement relation of the viscous damper is described by experimentally calibrated fractional derivative Maxwell Model. The proposed model is validated by dynamic testing and A good agreement between predicted and experimental results is obtained.
-
An orifices fluid damper having the capacity of about 2 tons was designed and fabricated, and series of tests were performed to grasp the fundamental performance characteristics of it. Several important findings were observed and introduced in this paper. This fabricated orifices fluid damper will be applied to the structure under seismic load for the confirmation of its validity on structural vibration absorbtion as an extended study.
-
In this study, modeling methods for viscoelastic material are reviewed to investigate the vibration characteristics. Frequency response functions are obtained by employing experimental modal analysis and compared with the modeling results from a commercial software NASTRAN. Properties of equivalent model of the beam with damping material are also calculated by using the RKU equation.
-
The updating of the FE model to match it with the experimental results needs the modal information. There are two causes where this methodology is ill-equip to deal with; under-determined and ill-conditioning problem. In this research, the feedback exciter which uses the summation of the white noise and the signals from the measurement sensors multiplied with feedback gains is proposed. The new energy path generated by the feedback exciter changes the modal characteristics of the system and this additional modal information can solve the under-determined problem in the model updating. Through the proper selection of the exciter and sensor locations and the feedback gain, the eigenvalue sensitivity of the updating parameters which cause the ill-conditioning of the sensitivity matrix can be modified. This methodology does not require any additional equipments, makes the acquirement of the additional modal information easy and is robust to the measurement noise.
-
A significant trial has been performed for estimation of noise level of a cross flow fan for air conditioning system. In general, measurements of noise level of machinery require rigorous equipment involving an anechoic chamber with precision gauges. The apparatus is expensive to utilize and is not easy to construct. In this work, we adopt static pressure sensing from an ordinary pressure transducer for prediction of noise level of a rotating fan. The present procedure is finding sound pressure from the static pressure by manipulating Light-Curle equation depicts noisy energy in terms of pressure on surfaces of noise generators. Sound power level near core unit of the fan is evaluated with the present methodology in a normal laboratory room without any sound absorbers. The method is easy and shows good prediction results compared with precise measurements by using microphones.
-
Suction valve fluttering is generated by reciprocating motions of the piston inhaling and discharging process of gas in the hermetic compressor. A reactive type suction muffler, which produces high pressure-drop because of its complicated flow path, controls the impulsive noise radiated from the flutter of suction valve. The high-pressure drop in the muffler increases the transmission loss, but reduces the EER(Energy Efficiency Ratio) of the compressor. We consider how to design the high acoustic attenuation and low pressure-drop performance to take account of the acoustic and flow performances of the suction muffler. In this study, we identified the suction noise source of compressor from the measurement of the acoustic pulsation and flutter of suction valve. We analyzed the acoustic characteristics of muffler using the finite element method, and compared the experimental and analytical characteristics of flow path of suction muffler. Theoretical predictions and experimental results are compared from the viewpoint of the acoustic performance and energy efficiency of the compressor.
-
Compressors are the main source of noise of refrigerators and air-conditioning unit. Recent studies on the sound propagation of rotary compressors showed that the accumulator is a significant source of noise generation. This paper describes a design change of a rotary compressor for noise reduction using topology optimization. Topology optimization has been developed and used to find the most effective structural configuration in the early stage of design procedures. FE model of the rotary compressor composed of all the components is built for the topology optimization. Topology optimization results show that the empirical design for the present structure fail to constrain some resonance modes and a new component is required.
-
차음성능 측정에 관한 국제간 신인도 향상을 위하여 home and away 테스트가 수행되었다. 동일 시편에 대한 비교 테스트 결과 대부분의 시편에서는 STC 1 ㏈ 이내의 차이를 보였다. 다만, 특정 시편의 경우 STC 5 ㏈의 차이가 발생하였다. 주원인으로는 잔향시간 측정 오차가 주원인으로 추정되며, 또한 부수적인 원인으로는 시편의 제작 및 설치의 차이 때문인 으로 사료된다.
-
This paper presents the effect of air gap insertion on the results in measuring the transmission loss of sound barrier by using APAMAT. The measured results show that air gap insertion improves transmission loss as by two-room method or intensity method. The measured results are compared with the predicted transmission loss using MATLAB GUI program based on the transfer matrix method. Predicted results were found to be in reasonable agreement with measured results.
-
This paper discusses an experimental method for measuring the insertion loss (IL) performance of multi-layered insulations that are used in vehicles. Instead of two adjacent reverberation chambers which are generally used to measure the transmission loss (TL) of the large sound isolation materials, air-borne sound insulation tester was utilized to determine the IL and articulation index (AI) of standardized insulation materials. In comparison to reverberation chamber method, air-borne sound insulation tester method is more space-saving, more time-saving and more simple to the automotive acoustics. From the empirical results, it is found that the performances of insulation materials are closely connected with density of polyurethane foam, thickness of heavy layer, thickness of polyurethane foam, and application ratio to panel area.
-
Damping materials show variant characteristics depend on frequency or temperature condition. Therefore, we need to measure damping material characteristics called a loss factor or a young's modulus varying frequency or temperature condition. In this article, measuring procedure and method has been introduced for damping material using a sticking damping material with a thin steel beam. And it shows a temperature effect to damping materials.
-
Near-field acoustic holography is a powerful tool to visualize sound sources. This method requires pressure measurement at many points for a good hologram. Thus one has to measure carefully so that errors due to the uncertainty of position, sensor mismatch, and so on are reduced. A method to solve this problem is to use a well-designed measurement system. This paper introduces a sound visualization system at center for noise and vibration control (NOVIC), KAIST, and addresses the advantages in terms of the error reduction. The system consists of array microphones, array jigs, a system to control the position and the velocity of the jigs, a data acquisition system, and a monitoring system. This paper also shows some sound visualization results when the system is applied to a speaker and a computer. The results verifies that the sound visualization system is useful for identifying sound sources.
-
Identification of noise sources, their locations and strengths, have been taken great attention. The method that can identify noise sources normally assumes that noise sources are located at a free field. However, the sound in a reverberant field consists of that coming directly from the source plus sound reflected or scattered by the walls or objects in the field. In contrast to the exterior sound field, reflections are added to sound field. Therefore, we have to consider the reverberation effect on the source identification method. The main objective of this paper is to identify noise source in the reverberant field. At fist, we try to identify noise sources in a rigid wall enclosure using the spherical beamforming method. In many case of practical interest, the wall has an admittance so that complex reflection process occurred. In this paper, we assumed the complex reverberant field in the enclosure to be the sum of plane waves with random incidence and magnitude. Then the effects of reverberant field at interior source identification have been studied theoretically as well as experimentally
-
The impinging tones by high-speed plane jets are investigated for the characteristics of edgetone generation based on experimental observations. Experiment has been performed for edgetones with a slit nozzle and a wedge system. The jet in the experiment is varied from low to high subsonic speed to obtain the effect of the speed on the frequency characteristics of impinging tones. The experimental data obtained previously for edgetones and platetones by various nozzles are compared with the present edgetone data for the condition of tone generation, the frequency ranges and the effective source point. It is found that the jet speed has no fundamental influence on the impinging tone characteristics. Regardless of the jet speed, the effective source point is about a quarter wavelength downstream from the edge tip. With increase in jet speed, the influence of the nozzle configuration is decreased and the operating frequencies show good coincidencies by normalized parameters based on the slit thickness.
-
The discomfort due to squeaks and rattles appearance inside the car has serious repercussions on consumer's opinion about acoustic quality of the vehicle and may change his economical behaviour. In this paper, we present a set of tools for squeaks and rattles processing implemented on a PC-based two channels analyser and grouped in a friendly interface. (omitted)
-
A structure gauge assessment is needed to ensure that a railway vehicle can run safely along a length of track without coming unacceptably close to lineside structures or equipment, or to vehicles running on adjacent tracks. This apparently straightforward question is in reality very complicated. The amount of space required for the safe passage of a railway vehicle is significantly greater than its static body profile for a number of reasons as follows: as the vehicle runs along the track, the track input excites the vehicle and it moves on its suspension. On curved track its geometric position leads to curve overthrows. A number of different approaches have been used to answer this question and some are described and specially applied to urban train by computer simulation in this paper. The program used for calculating the kinematic and swept envelope is the VAMPIRE made in U.K.
-
To provide faster service and to relief the road traffic jam, the increase of service speed of conventional railway has been intensively considered. In this study, we measured and analyzed the vibration ride comfort of Saemaeul Train to evaluate the feasibility of 5km/h speed-up in curves and l0km/h speed-up on straight tracks. Four main lines, such as Honam, Kyungboo, ]anghang, Kyungjeon were chosen as representative lines for speed-up feasibility study. The increase of mean ride comfort index in case of speed-up is 0.5-2㏈. The mean ride comfort index of vertical direction in case of speed-up is 107 ∼110 ㏈ for Honam line, 104 ∼112 ㏈ for Kyungboo line, 108∼112 ㏈ for Janghang line and 105∼108 ㏈ for Kyungjeon line. Through this study, we found that the Saemaul Express has slight margin to increase the service speed from the view point of vibration ride comfort.
-
In this study. a computer simulation of the Korean High Speed Prototype Test Train was performed to investigate the dynamic behavior(running stability. safety and comfort) in detail design process. The simulation model which was prepared by ADAMS/Rail V10.l consists of power car and middle car assembly (2 motorized cars + 3 trailer cars). The nonlinear analysis takes into account the full vehicle model including wheel/rail contact and the influence of disturbed track. Throughout the dynamic calculation of KHST on the straight and the curved track. accelerations in car body. ride comforts and wheel rail forces were investigated.
-
In this study, we measured and analyzed the interior noise, the rolling noise and the engine noise at Honam line(Seodaejeon- Jangseong) for passenger and power cars. The noise level is below 69㏈A for Seamaeul PMC(Powered Motor Car) coachs, below 65㏈A for Seamaeul and Mukungwha coachs, over 80㏈A for the driver's room of PMC and DEL (Diesel-Electric Locomotive). We also proposed the criteria of interior noise in free field conditions, below 67㏈A for passenger cars, below 86㏈A for power cars.