Proceedings of the IEEK Conference (대한전자공학회:학술대회논문집)
The Institute of Electronics and Information Engineers (IEIE)
- 기타
2002.06a
-
In this paper, we are designed and verified a FFT/IFFT processor that is possible from the wireless LAN environment which is adopted international standard of the IEEE802.11a. The proposed architecture of the FFT/IFFT has Radix-2 64point SDF(single-path delay feedback) Pipeline technique and DIF(Decimation in Frequenct) structure. The FFT/IFFT processor has each 8 bit complex input-output and 6 bit Twiddle factor. we used Max-PlusII for simulation and can see that processor is properly operated
-
In this paper, we analyze high-rate wireless LAN system based on Orthogonal Frequency Division Multiplexing(OFBM) transmission method. For this analysis, actual channcl measurement model of indoor office areas such as JTC model was adopted, and cllanncl coding of IEEE 502.11 and channel equalizer over multipath environment are also considered.
-
In this paper, we propose adaptive despreading receiver for multi-code PW-CDMA system with binary-level clipping. The distortion due to clipping the multi-level signal causes the performance degradation. Adaptive despreading alleviates the effect of clipping. It is shown that the proposed adaptive despreading receiver achieves smaller BER than conventional despreading receiver for multi-code PW-CDMA system with binary-level clipping.
-
We propose in this paper a companding scheme for PAPR (Peak-to-Average Power Ratio) reduction in OFBM (Orthogonal Frequency Division Multiplexing) systems. By exploiting statical distribution of OFDM transmit signals, the proposed scheme effectively reduces the PAPR by compressing the peak signals, while maintaining the average power unchanged. Simulation results are provided to show good performance of the proposed scheme.
-
갈수록 복잡해져 가는 시스템을 한번에 하나의 칩까지 완성하기란 쉬운 일이 아니다. 컴퓨터에서 시뮬레이션이 정상적으로 되었다고 해서 완벽한 동작을 보장하는 것도 아니다. 전체 시스템을 검증하는 것도 컴퓨터 시뮬레이션으로는 불가능한 단계에 왔다. 이로 인하여 시스템 전체가 제대로 동작하는지 검증하기 위한 새로운 방법이 요구된다. 이러한 개념으로 접근하고자 하는 것이 본 논문에서 이야기할 플랫폼 기반의 SoC설계이다. 이 논문에서는 임의의 무선통신시스템의 요구사항을 만족할 수 있는 베이스플랫폼 보드의 구조와 설계 시 고려되어야 할 점을 제안한다.
-
본 논문에서는 W-CDMA(Wide-Code Division Mul-tiple Access)용 Systolic 어레이 구조를 잣는 상향링크 빔형성기법에 대한 성능 분석을 하였다. 적응 어레이 안테나와 Systolic 구조의 MVDR(Minimum Variance Distortionless Response) 알고리즘을 사용하여 구해진 가중치 벡터를 이용하여 원하는 사용자의 방향으로 빔을 형성하고 원하지 않는 사용자의 방향으로는 null을 형성하는 공간필터를 적용하여 W-CDMA 상향링크에서 다중 경로 페이딩과 다중 접속 간섭의 증가에 따른 수신 성능을 분석하였다. 그리고, 안테나 시스템에서 사용되는 가중벡터를 갱신하기 위해 Systolic 구조의 MVDR과 역방향 파일럿 채널을 이용하는 QR-RLS(QR-Recursive Least Squares) 알고리즘을 적용하였다. 본 논문에서는 빔 형성기에 사용하기 위한 역행렬의 계산과 정에 Systolic 어레이 구조를 적용하여 병렬적인 고속처리가 가능한 방법과 효율적인 계산과정을 위해 MVDR 과 QR-RLS 알고리즘을 적용한 공간 필터링의 성능을 소개한다.
-
본 논문은 수평적 시공간 부호화 기법(Horizontal Space-Time Coding)과 송수신단에 별도의 빔형성 기법을 결합한 JBSTC(Joint Beamforming Space-Time Coding) 구조에 대한 제안 및 동작원리를 기술하고 성능을 분석하였다. JBSTC는 MIMO(Multi-Input Multi-Output) 송수신 시스템 채널 모델링을 기반으로 송신측 안테나간 상호 상관 행렬과 수신측 안테나간 상호 상관 행렬을 이용하여 송수신 빔형성기의 안테나 가중치들을 계산한다. 본 논문에서 제안하는 JBSTC 방식은 송수신단에서 발생하는 안테나 간격과 각퍼짐에 따른 상호 상관 값을 효과적으로 보정함으로써 기존의 수평적 시공간 부호화 기법보다 우수함을 알 수 있다.
-
A new smart antenna scheme based on spatial FFT is proposed. By combining the output of spatial FFT, the proposed structure shows similar performance gain compared to ordinary smart antenna systems. Moreover. the proposed scheme could be easily integrated to general receiver without beam focusing module. The analysis and simulation results show that the performances of proposed scheme are comparable to ordinary smart antenna systems
-
본 논문에서는 MISO(Multiple-Input Single-Output) 시스템에서 시공간 블록 부호(Space-Time Block Code; STBC)와 전송 고유빔 형성기의 결합을 통해 전송 다이버시티 이득과 빔형성 이득을 동시에 추구하는 기법에 대해 설명하였다. 빔형성 이득을 대한 성능을 분석하기 위해 채널간 상관 정도에 따라 모의실험을 통해 성능을 분석하였다. 성능 분석 결과 일반적인 STBC 기법을 적용하는 기법보다 우수한 성능을 보임을 확인하였다
-
Alamouti proposes a two branch transmit diver-sity scheme that provides the same diversity order as maximal ratio combining at the receiver. It has many advantages of no bandwidth expansion, not requiring channel information at the transmitter and simple maximum likelihood decoding at the receiver. Papadias and Foschini extend this sch-eme to four transmit antennas and suggest several schemes to decrease the interference component and allow the attainment of the open-loop capacity. This paper shows the performance of ZF and MM-SE schemes comparing with ideal case on 4xl sy-stem over BER and 10% outage capacity.
-
This paper presents a QoS-guaranteed traffic control system which supports QoS of realtime packet transmission for the multimedia communication. The traffic control system presented in this paper applies the integrated service model and provides QoS o(packet transmission by means of determining the packet transmission rate with the policy of network manager and the optimal resource allocation according to the end-to-end traffic load. It also provides QoS for the realtime packet transmission through the AWF2Q+ Scheduling algorithm and per-class queuing method.
-
QoS support for the Internet traffic becomes an important future requirement of various network devices such as routers and switches. Differentiated Services(Diffserv) is considered as an efficient feasible solution for providing different service characteristics to different classes of network users. IETF Diffserv working group has already defined a general architecture of Diffserv and is extending its detail features. Network vendors also start implementing Diffserv enabled network devices. However, the management of Diffserv is not fully standardized yet. This paper, we present methods of traffic flow control in Diffserv Networks. we have designed a Diffserv Traffic Control system.
-
In this paper, we study the network structure that can guarantee the end-to-end quality of service in the Explicit multicast network. In order to guarantee the end-to-end quality of service, we adopt the end-to-end measurement based admission control (EMBAC) scheme. For the effective measurement of the network state and minimum influence on the current data traffic, the queue structure, which the drop precedence in assured forwarding (AF) Per hop behavior (PHB) of the differentiated service (Diffserv) is applied to, is proposed. Through a simulation, we show that EMBAC can make tile controlled load service in tile AF PHB applied Xcast network, and the qualify of the admitted traffic is guaranteed. In addition, the performance of the EMBAC is changing according to the selling parameter of AF PHB.
-
본 논문은 VoIP 시스템에서 적용 가능한 QoS 구조를 연구하였다. 현재 망 구조에서 실시간 트래픽은 최선형 트래픽과 구별이 되지 않아 보장받지 못한다. 따라서 본 논문에서는 QoS 구조를 위해 IETF에서 제안된 차등화서비스와 Intserv over Diffserv를 개관하였고, 이런 환경에서 VoIP 트래픽에 대한 품질을 보장하기 위한 QoS 구조를 연구하였다 또한, 측정기반 수락제어에 의해 기존망에 비해. 보다 좋은 품질을 제공할 수 있는 VoIP 시스템 구조도 함께 연구하였다.
-
In this paper, various equalizers are considered to improve the performance of Home Phoneline Networking Alliance (HomePNA) 2.0 system under dispersive channel with intersymbol interference. We evaluate and compare the performances of Recursive Least Squares (RLS) and Least Mean Squares (LMS) adaptation algorithms. Computer simulations show that the equalizers utilizing tile RLS algorithm outperforms the LMS algorithm, especially for the system of high symbol rate and complex constellation.
-
본 논문은 HomePNA 2.0 시스템에서 채널에 의한 왜곡을 보상하기 위한 방안을 제시하는 것으로서 심벌률과 전송 방식에 따른 등화기를 Fast RLS 알고리즘인 FTF (Fast Transversal Filter) 알고리즘을 사용하여 구현하여 그 성능을 분석하며, 또한 헤더 부분의 미결정 심벌들을 이용하는 DFE (Decision Feedback Equalizer)형태로 등화기를 구성하고 이에 대한 성능을 분석하고자한다.
-
In this paper, adaptive minimum mean-squared error (MMSE) multiuser detector combined with decision-feedback detector (DFD) is considered fur near-far resistant DS-CDMA system. To provide a reliable input to the adaptive MMSE detector, multiple-access interference (MAI) is regenerated using bit estimates from DFD and subtracted from the received signal. In the adaptive MMSE detector, the effect of the imperfect cancellation is compensated by a least mean square (LMS) algorithm. Through the numerical results, it is shown that, in a near-far situation, the proposed scheme provides superior performance to the matched filter (MF) receiver, adaptive MMSE detector, and DFD in terms of the bit error rate (BER).
-
In this paper, we consider an algorithm for effectively providing data services for mobile users with different levels of priorities in a DS-CDMA system. The priority level of a user is specified by a factor that is a weighting on the instantaneous data throughput of the user. We define tile weighted instantaneous aggregate data throughput and use it to characterize the performance of the prioritized data service. Our prioritized data service is implemented so that the weighted instantaneous aggregate data throughput is maximized via efficient power and spreading gain allocation. We present efficient algorithms for computing tile optimal power and spreading gain allocation.
-
In this paper, we analyze a physical layer of W-CDMA .system and design a transmitter and receiver by using ADS (Advanced Design System). Also, we simulated a link level performance with different channel estimation algorithm in Jakes fading channel environment. For the channel estimator, we used the WMSA(Weighted Multi-Slot Averaging) algorithm, EGE(Equal Gain Estimation) algorithm and SSE(Symbol-to-Symbol Estimation) algorithm. This study will be useful in the analysis and design of W-CDMA system.
-
The WRR scheduling algorithm is widely used in ATM networks due to its simplicity and the low cost of hardware implementation. It guarantees minimum cell rate according to the weight of each queue. The fairness is a important factor for ABR service. That is, Scheduling algorithm allocates network resources fairly to each VC. In this paper, we propose a scheduling algorithm for satisfying the two fairness criteria, MCR plus equal share and Maximum of MCR or Max-Min share, among the six criteria defined by ATM Forum TM 4.1 specification. The WRR, Nabeshima et al, and the proposed scheduling algorithms are compared with respect to fairness and convergence time throughout experimental simulation.
-
Maintaining a proper level of cell lead, system throughput can be maximized by a transmission rate control over the uplink in DS/CDMA cellular system to support integrated services of real-time and delay-tolerant traffic. We find that the cell load-based rate control scheme can be further enhanced by taking the varying channel condition into account In conjunction with some fair scheduling algorithm. Our simulation results show that the proposed scheme outperforms the original cell load-based rate control with the round-robin sharing scheduling scheme.
-
It is important that fault management of devices which is composing network in the next-generation internet environment. It is best method of operating network safely and efficiently. In this paper, we have suggested double message broker architecture to transmit trap messages in web-based fault management system using Java technologies. The double message broker fault management system shows that manager can do its own job efficiently
-
Fair Queueing has been studied only on wired network. When it is applied to wireless netowork, the collision phenomenon makes a problem.'rho information of queue of MT cannot be transferred to fair queueing algorithm In real time easily. We propose wireless fair queueing scheduler that protects short term farirness and long term fairness. We developed it in TDMA/TDD enviroment. Our scheme also supports uplink and downlink at the same time. And it can make subframe boundary based on fair scheduling algorithm.
-
In this paper, we analyze All IP network architecture and VoIP Service procedure using U Multimedia domain. And, we propose QoS Resource management scheme using with statistical measurement based admission control 8l rate based borrow bandwidth to improve real-time traffic QoS guarantee.
-
In this parer, a novel architecture for Home gateway is Proposed. In home network system, there exist many different kinds of data types, like audio, video, and control information. And the communication is over multiple networks, like bluetooth, wireless LAN, USB, IEEE1394, and Power Line Communication (PLC). The hardware architecture of the Home gateway presented in this paper is based on ISO/1EC JTC 1/sc 2S/WG 1(1,2). The architecture proposed in this paper takes into account the characteristics of home network environment, so the Packets in the home network system can be processed very efficiently.
-
This paper analytical models of a centralized approach based on SNMP Protocol, distributed approach based on mobile agent, and mixed model which is tile existing mobile agent model in order to overcome large communication numbers of SNMP and accumulated data of mobile agent. And then, we compare and analyze these analytical models. Performance evaluation results show that performance of mobile agent and the mixed model is less sensitive to the network traffic and more profitable for complex network environment than that of SNMP.
-
SNMP is generally used protocol for network management. SNMP need MIB for exchanging management information But, method for sharing MIB is not automatic. General MIB sharing architecture is done by network management operator by manually. In this paper we describe exchanging MIB automatically using meta-MIB. We will formalize SMI as MIB structure. This meta MIB represent information about MIB of NE Agent. Meta MIB has Information of object in the MIB, Structure and index information fur columnar object, meaning of subtype at INTEGER syntax. Also, trap related information is represented too. In this paper, MIB information is represented as instance of meta MIB. This architecture will provide a method for automatic MIB exchanging
-
It is required to network to make more intelligent packet processing and forwarding for increasing bandwidth and various services. Classification provides these intelligent to network which is acquired by increasing number of rules in classification rule set. In this Paper, we propose a classification algorithm efficient to scalable rule set ahead as well as Present small rule set. This algorithm has competition to existing methods by performance and advantage that it is mixed with another algorithm because il does not change original shape of rule set.
-
This paper is proposed structure which it sees currently the problem point which it follows in the independent space for work which the members who do a same work from the environment which is to fall tile at distance, therefore the MPLS based VPN necessary to follow, it forms the small-scale group which is closed again with the CUG(Closed User Group) it will be able to own jointly information to present a structure, the individual small-scale groups are closed from outside and the group members are the CUG authentication Process for the security maintenance the model which is possible.
-
The IEEE 802.lla PLCP H/W for Processing efficiently control message between MAC and PHY is designed. Slate machine and clock control according to rate is designed and timing diagram is verified on the FPGA simulation environment.
-
This paper is about a high-speed MAC (multiplier and accumulator) design applying radix-4 and radix-8 Booth's algorithm at the same time. The optimized hybrid radix design for high speed MAC has taken advantage of both a radix-4 and a radix-8 architectures. A radix-4 architecture meets high-speed, but it takes much more power and chip area than a radix-8 architecture. A radix-8 architecture needs less power and chip area than the other, but it has a bottleneck of generating three times the multiplicand problem. An optimized hybrid architecture performs tile radix-4 multiplication partially in parallel with the generation of three times the multiplicand for use of tile radix-8 multiplication. It reduces the concerned bit width of multiplier in radix-8 multiplication.
-
We investigates the functions of UPnP protocol that would be used to provide easy and cheap access for home networking. We suggest that a proxy device may reduce the cost of establishing UPnP network if it serves as an interface between UPnP and X10 protocol. We also describe the design of UPnP proxy device and the service scenario.
-
VoiceXML is designed for creating audio dialogs that feature synthesized speech, degitized audio, recognition of spoken and DTMF key input, recording of spoken input, telephony, and mixed-initiative conversations. Uses the VoiceXML and there is a Place objective which does information home appliance machinery and tools control. When it uses tile VoiceXML, il will be able to provide a bias characteristic to the user The XML base the gearing with different civil official system is possible. With studying YoiceXML and OSGi, this paper has designed and implemented the control architecture of Information home appliances.
-
2.4Ghz ISM 대역에서 동작하는 Bluetooth는 동일한 대역에서 동작하는 WLAN(802.11.b), Cordless phone, microwave oven등의 신호가 interference로 작용하여, 성능이 크게 저하된다. 특히 Bluetooth과 WLAN은 상호간 interference로 작용하여 상호 성능 저하를 초래한다. 따라서, 두 장치간의 coexistence를 위한 방안으로 adaptive hopping frequency(AFH)이 제안되었다. 이 논문에서는 3 channel status를 이용한 AFH 방식을 제안하고, 그 성능을 검증하였다.
-
본 논문은 2세대 규격인 IS-95와 3세대 규격인 W-CDMA 혼용 디지털 채널화기 구조에 대한 제안 및 동작원리를 기술하고 성능을 분석한다. 실제적인 1.25MHz 대역폭을 갖는 IS-95와 SMHe의 대역폭을 갖는 W-CDMA 혼용 디지털 채널화기를 위한 BFT 필터 뱅크 적용시의 문제점을 지적하고 혼용 디지털 채널화기의 구조로 별도의 정류자를 사용하는 폴리페이즈 필터 뱅크 구조를 제안하고 성능을 분석한다.
-
This paper has been studied a predistorter which is able to linierizing of RF amplifier using schottkey. If input signal level is low, input signal is delivered directly. And if input signal level is high, input signal Is delivered with decreasing. So RF amplifier always works at saturation region .When this predistorter is used to simplified C-class RF amplifier, we have concluded that efficiency is improved about 3%.
-
In this paper, an adaptive interference canceller (AIC) Is applied to the space-time coded DS-CDMA system in fading channels with arrival time difference from multiple transmit antennas In a CDMA system, arrival time difference causes not only inter-antenna and Inter-symbol interference but also multiple-access Interference even in a downlink. To mitigate the effect of the Interferences an AIC and ML decoding joint scheme Is proposed fur a space-time coded DS-CDMA system in which an adaptation process of tile AIC is merged in the Viterbi decoding algorithm. The performance of the proposed receiver is evaluated for the system with two transmit antennas. It is shown that the proposed receiver achieves significant performance improvement over the ML decoding receiver without the AIC
-
An adaptive predistorr is proposed to compensate for the nonlinear distortion of a high power amplifier (HPA) in 16 QAM system. It fumed out that the proposed predistorter using a variable step-size least mean square (VSSLMS) algorithm is stable and can reduce the Total Distortion (TD) to 0. 1dB at the HPA output backoff=0.0 dB.
-
For a company operating lots of vehicle, such as taxi companies or delivery company, a system telling the position of each vehicle is essential. Conventional methods are based on personal communication between a operator in head-office and driver at the car. Since driver cannot respond to the communication while he drives or when lie is out of car. the communication often fails. So, a system identifying and reporting the vehicle position offers groat help to those kind of company.
-
Recently, two kinds of the digital satellite receiver for radio and television have been developed as the global receiving system. The frequency bands of the satellite radio system are ranging from 1, 400MHz to 2, 600MHz, while the satellite television system are ranging from 11, 000MHz to 13, 000MHz New anti-discern antennas have been developed so that satisfies the Omni-characteristics in the horizontal directivity and approximately 45
$^{\circ}$ 'elevation angle in the vertical directivity. These results were similar to the discern antenna except the anti-vertical directivity. -
The design and fabrication of Q-band 3-stage monolithic microwave integrated circuit(MMIC) driver and power amplifiers for WLAN are presented using 0.2
${\mu}{\textrm}{m}$ AlGaAs/InGaAs/GaAs pseudomorphic high electron mobility transistor(PHEMT). In each stage of the MMIC DA, a negative feedback is used for both broadband and good stability. The MMIC PA has employed a balanced configuration to overcome these difficulties and achieve high power with low VSWR over a wide frequency range. In the MMIC DA, the measurement results arc achieved as an input return loss under -4dB, an output return loss under -l0dB, a gain of 14dB, and a PldB of 17dB at C-band(36~ 44GHz). The chip size is 28mm$\times$ 1.3mm. The developed MMIC PA has the l0dB linear gain over 360Hz to 420Hz band and 22dBm PldB performance at 400Hz. The size of fabricated MMIC PA is 4mm x3mm. These results closely match with design results. This MMIC DA Sl PA will be used as the unit cells to develop millimeter-wave transmitters for use in wideband wireless LAN systems. -
In this study, we proposed a specification which is able to estimate tile uncertainty more easily and quickly and also able to maintain a confidence level when measuring tile magnitude and phase of 1-port and 2-port transmission.reflection coefficient using a VNA and attached coaxial cable probes. This proposed specification is available when it needs extra special condition of uncertainty estimation and when there is no additional standard equipment like as beadless airline or mismatch standard at the measurement institute. We compared and examined this proposed uncertainty estimation method with recommended EA specification and Agilent specification. As a result, we think that this proposed specification can be used as a reference for uncertainty estimation and calculation of VNA system, that is, a reference based on the IS0/1EC 17025 requirements.
-
In This paper, a microstrip slot antenna is designed and fabricated for wireless LAN at 5.8GHz band. The microstrip slot antenna is fed by CPW and formed the inductively slot and tile capacitively slot. To obtain wideband, the inductively slot is designed at 5.3GHz and the capacitively slot is designed at 5.8GHz. Resonant frequency of the fabricated microstrip slol antenna is 5.BCD, the bandwidth for VS%<1.5 is 29% and the gain is 4.6dB. The 3-dB beamwidth of E-plane and H-plane is 80 “ and 120 ”, respectively
-
In this paper, 2-stage Power amplifier with external bias controller for\ulcorner IMT-2000 handsets was designed using SiGe HBT with excellent linearity to 1\ulcornereduce size and weight. The designed amplifier has 26.5 dBm output power, 33% power added efficiency, and 22 dB linear power gain in 1920-1980MHz frequency range.
-
In this paper, a microstrip Patch antenna with the T-shaped slits, which are employed to reduce the patch size. is proposed for GPS In order to analyze characteristics of the antennas are defined green function of the moment method. The microstrip Patch antenna and microstrip Patch with the T-shaped slits are fabricated. The numerical result of return loss and -10d13 bandwidth are compared with measured results.
-
In this paper, we deal with performance improvement of OBE for automatic gate clearance system by using DSRC network of 5.8GHz ISM band. A data format is improved to represent Rx and Tx information which is need to perform clearance at the gate of container terminal. An error message caused by data discordance is added to Previous data format. A graphic LCD monitor is used to control a character font and use Korean.
-
We analyzed radiation characteristics of dipole antenna in a lossy 9round with conducting object located above ground. Electric field integral equation is used to solve the problem. In this integral equation, GPOF(Generalized Pencil of Function) method is applied to derive the closed form of the electric field due to a current source. Surface current on a conductor is expanded with a well-known vector triangle basis function. The singular integration of a triangle patch is transformed to the non-singular integration by Duffy's method. This transformed non-singular integration is easily calculated by using one-dimensional Gaussian quadrature rule, instead of usual closed form evaluation.
-
One-dimensional radar signature, such as range profile, is highly dependent on the aspect angle. Therefore, radar target recognition over wide angular region is a very difficult task. In this paper, we propose the Bayes classifier with Gaussian mixture model for radar target recognition over wide-angular region and compare performances of proposed technique and radar target recognition with subclasses concept in the literature of probability of correct classification ratio.
-
This paper is about the implementation of Passive RFID(Radio Frequency Identification) tag system using a capacitive method, and explains the design and circuit's structure of this system. Fundamentally the capacitive RFID tag system consists of a tag reader, a passive tag and a host computer. And then this paper shows the system's prototype which analyzes a specification, and suggests the passive RFID system as a new method which manufactures a low cost tag system easily
-
We implemented 2.5Gbps optical transponder by using uncooled laser diode and measured temperature effects of 2.5Gbps uncooled laser diode, such as optial power vs. injection current, extinction ratio, and power penaty.
-
We suggest binary image decryption system using two-wave mixing in photorefractive crystal. Compared with a conventional method, this method can make optical alignment easily, and brighten the encrypted image even if a small input signal, by index grating of photorefractive crystal. Also it can reconstruct the encrypted image by only reference beam in real time.
-
A study on a Measurement Method of the Circular-to-Rectangular Waveguide Transition characteristics.In this paper, we present a simple method for characterizing a rectangular waveguide to circular waveguide transition Three standard loads consisting of a short circuit, an offset short circuit 1, and an offset short circuit 2 are sequentially connected to the circular waveguide port and the reflection coefficient at port 1 Is measured for each case. From known reflection coefficients, of standard loads and measured reflection coefficients, the scattering matrix of the transition Is obtained. The proposed method Is verified by the numerical experiment using a commercial software HFSS and by measurments of a actual rectangular-to-circular waveguide transition.
-
Design methods are presented for a broadband corrugated horn antenna operating X/Ku band (7.25-14.5 CHz). The corrugated horn consists of a circular waveguide taper, a mode converter, a waveguide-to-horn transition, and a hem section. Methods of design are presented for each section. The designed antenna shows excellent characteristics over the entire operating frequency range.
-
In this paper, we propose the OADM based on a Mach-Zehnder interferometer(MZI) with FBG(fiber Bra-gg grating) in the interferometer arms. The OADM us ing FBG and MZI is able to minimize system and red uce weight. We analyze output\ulcorner characteristics of OAD-M, and present the optimum design data through the computer simulation, and obtain the good experimental results. Also, the proposed OADM is suitable to DWD-M(Dense WDM) system because it has the narrow 1-inewidth.
-
In this paper, we propose the FBG design using coupled mode theory based on perturbation theory. FBG can be used to extract the specific wavelength channel from the transmission ]me when many wavelengths are coupled in a multiwavelength transmission line. To analyze output characteristics of FBG and get optimum design data, we simulate through computer and verify by experiment. From the results obtained by simulation and experimentation, the proposed FBG fits for DWDM(Dense WBM) system because of the tunning narrow linewidth.
-
A digital watermark is an invisible mark embedded in a digital image which used for copyright protection. In this paper, we propose a new optical watermarking system. A optical watermarking system is applied for digital watermarking by phase hologram and Mach-Zehnder interferometer. A optical watermarking technique to be hidden is phase modulated in a random patten, and its Fourier-transformed hologram image is superposed on a content image. The autentication information extract by using Mach-zehnder interferometer.
-
This paper has studied a management system for RCST of the Satellite Multimedia Internet Service through analysing the architecture and specification of BSAN based on Digital Video Broadcasting System. In this paper, designing and implementing RCST DPM and agent system are shown. The UCD-SNMP framework served as base station for implementation of the agent. And the message protocol between RCST DPM and agent system has been also defined to provide a way for interaction.
-
In this paper we describe the design and implementation of Electrical Ground Support Equipment(EGSE) for the CBS transponder testing. The main task of EGSE is to check out satellite systems, at system or subsystem level, during integration and validation phases of their life-cycle. Through a combination of hardware and software elements, EGSE supports manual, semi-automatic and fully automated testing. Automation is achieved by offering users simple, yet powerful means to write their own test application programs (test sequences) in high-level, test-oriented language and to run them in a strict real-time environment. The core of this environment is a user-configurable real-time database, containing all the information needed to calibrate acquired data, check them against predefined thresholds, automatically react to out-of-range conditions, display data using animated graphics or synoptic windows, and so on.
-
In this paper, an advanced load balancing algorithm in nth order Hypercube distributed system has been proposed. The new algorithm uses centralized load-balancing to avoid blocking phenomenon and processor thrashing, and shows the results which makes loads to approach average value of loads. The new algorithm os compared with several other algorithm and it shows a merit in cost function value.
-
It is predicted that the existing backbone network has encountered its limit due to massive growth in data traffic. Perhaps new WDM methods utilizing optical fibers are desirable. Also to assure reliance of the network detour routes fur collision recovery must be considered. But due to the redundancy occurred by allocating bandwidths to the detour route, the efficiency of the link my decline. In this paper, we designed a detour route to minimize the redundancy.
-
본 연구에서는 G.983.1 표준에 WDM (Wavelength Division Multiolexing) 기술을 이용하여 WDM-PON 구조를 제시하고, PON상에서의 주된 지연은 upstream 상에서 발생하므로 IEEE 802.Ip를 토대로 각각의 클래스별로 패킷을 분류하여 제안한 알고리즘을 통해 상향 링크상에서의 동적 채널 할당을 실험 하였다. 이를 토대로 WDM-PON에서 각 클래스별 다중 버퍼 방식의 효율성과 채널 할당 알고리즘의 타당성을 확인해 보고자 한다.
-
무선 랜 서비스는 전송 선로에 대한 제약이 적으므로 높은 이동성을 보장하지만 무선이라는 망 자체의 특성에 의해 여러 가지 제약을 갖게 된다. 본 논문에서는 고속의 통신 속도 제공의 어려움, 에러의 빈도가 높은 불안정한 통신 채널, 저전력 소비등의 해결과 같은 문제를 가지는 무선 랜의 제한적인 요소들에 의해 비디오 스트리밍이 어떠한 영향을 받는지를 분석한다.
-
We propose a new algorithm to detect shot change, which is necessary in retrieval of video data. In order to solve the problems of abrupt brightness change and similar brightness between frames in the typical shot change methods, we propose the hi-polarity histogram method which takes into account the distribution and magnitude of brightness changes in consecutive frames. We evaluate our algorithm with compressed and uncompressed video data and demonstrate its improved performance.
-
Many methods have been Proposed to reduce the PAPR of the OFDM signal. Among them a method that uses the time waveform of the different sub-carriers. The method is referred to as pulse shaping and it works with arbitrary number of sub-carriers and my type of base-band linear modulation. It has been shown, using this technique, that it is possible to design a set of time waveforms that reduce the PAPR of the OFDM transmitted signal and improve its power spectrum simultaneously. In this paper, we investigate the effect of some of these sets of time waveforms on the OFDM system performance in terms of Bit Error Rate (BER).
-
Downlink Shared Channel (OSCH) is used for high-speed packet service transmission in WCOMA. The power-controlled performances of the OSCH are studied through simulation works. Under various channel conditions and mobile speeds, the simulation results show that current power control scheme in WCDMA, especially for the OSCH power control, has some problems. In this paper, cause of problems is revealed. Also, the quantitative result related to the OSCH power control problem is analyzed.
-
This paper presents tile efficient polling architecture for simple network management protocol (SNMP). Now a day, tile internet traffics have been increasing rapidly within a few years as the subscriber's network to connect internet is provided commonly. With this trend, the network management traffics also make the same phases. To provide numerous higher Quality services to the customers, the management traffic must be controlled within the permitted limit. This paper proposes the policy-based felling architecture for SNMP MIB with several parameters and suggests the data collecting layer architecture for the efficient polling.
-
This paper proposes an efficient micro mobility scheme to support user mobility inside an access network which employs Ipv6. The proposed scheme, namely SMM(Sparse-mode Multicast for mobility), utilizes a class of multicast protocol, PIM-SM, in the visited access network to reduce signaling to the home agent as well as to the correspondent node and to minimize packet loss during the handoff when mobile user changes its point of attachment frequently. Through the simulation, the performance of the proposed SMM is analyzed and compared with those of Mobile nv6 and for the case which adpots PIM-DM. The result shows that SMM provides significantly better performance in terms of packet loss that is invariant to transmission rate and packet size.
-
Here we introduce so called Reference code-weighted sum of all PN codes used in the system-. We do inner product operation between received PN code and Reference code rather than locally generated PN code in the receiver. Acquisition process can be accomplished by only one inner product during full period of PN code. It's essential innovation against present method which can be viewed successive hypothesis test by inner product for entire candidate PH codes set. Well -defined decision region makes it possible. We suggest the. criterion fur designing the decision region and find a condition for weight (coefficient) of Reference code.
-
For the satisfying performance of a oil lubricator, design of a oil controller for the system which meets the required specifications and its supporting hardware that keep their functioning is important. Among the hardware of a control system, oil system are most vulnerable to malfunction. Thus it is necessary to keep track of accurate and reliable oil readings for good fusion oil lubricator performance. In case of oil lubricator ,data loss, ssr trigger error faults, they are detected by examining the data system output values and the major values of the system, and then the faults are recognized by the analysis of symptoms of faults. If necessary electronic -sensor values are synthesized according to the types of faults, and then they are used for the controller instead of the raw data. In this paper, a fast-32bit cpu micorprocessor applied to the control of flexible link system with the sensor fault problems in the error module fer exact positioning to show the applicability. It is shown that the fusion oil lubricator can provide a satisfactory loop performance even when the sensor faults occure
-
This paper rotates to tile FPGA that is reffered to as the UTOSPI. The design goal of the FPGA is to convert the UTOPIA-3 bus interface to the SPI-3 bus interface, so that the SAR chips on the ATM interface board can be interfaced to the packet processor through this FPGA. We Propose a new architecture that has two Dual Port RAMs and flow control signals. To buffer data, the UTOSPI has a Dual port RAM in the receive direction and the same size of that in the transmit direction. This design has been implemented, compiled, and tested using a Xilinx Virtex-I XCV-300E FPGA.
-
This paper proposed interface test method for performance verification of communication and broadcasting satellite between communication and broadcasting satellite payload and EGSE(Electrical Ground Support Equipment). We need ground support equipment for test them to performance verification and conform interface function of payload. This paper define tile telemetry transfer method for control payload using GSE(Ground Support Equipment) and receive telemetry data collected from GSE through bus simulator
-
This paper has been proposed about the efficient ACL data transmission method by link quality for Bluetooth. By tile host tile HCI command confirm tile link quality values and change the packet type into several environment. And then we can analyze the data rate through this. From the construed result, after the suitable ACL packet type had been selected, the efficient data transmission method was proposed.
-
This paper has been understanded the whole concept of hop sequence in bluetooth baseband and studied algorithm of its each type. It is implemented and verified both hardware and firmware of hop sequence according to Sepcification ver.1.1, and compared and examined two schemes with performance, size, cost, and time-to-market, etc. This paper is suggested that it is the efficient system division to design optimum system depending on developing environment.
-
본 논문에서는 IMT-2000 WCDMA 시스템의 기지국의 수신신호에 대한 WCDMA 역방향링크 디지털 빔포밍 적용구조를 제시하고, 이의 성능을 측정하기 위한 빔포밍 시뮬레이터를 구현하였다. 실제 WCDMA 시스템에 근거해 수신 신호를 모델링하고, 기본 신호 모델을 대상으로 빔포밍과 전력제어등의 알고리즘을 적용하였다. 또한 셀네의 각 사용자들의 이동을 정의한 사용자 이동 프로파일을 구성하여 적용함으로써 실제 이동통신이 이루어지는 환경과 유사한 시뮬레이션 환경을 설정하게 되었고, 이를 통하여 빔포밍을 적용한 시스템에 대한 성능 분석의 신뢰도를 향상시켰다
-
This paper is proposed due to the fact that resolving domain name with conventional input method to PDA is not so convenient. The substance of this paper is that a user Pronounces tile character which represents tile domain name and that vocalized character is transferred through the GATEWAY, where DNS service can be received in return. PDA receives, compress and send the voice to the GATEWAY, Then, the GATEWAY uncompress, recognizes the voice, converts to characters, search for the mapping entry After mapping to the mapping entry, the GATEWAY sends the DNS request. Combining two entities makes DNS service based on the human voice possible.
-
This paper deals with an improved method of utilizing end-to-end bandwidth in the All-IP environment. The proposed method includes compression of UDP/RTP headers, and multiplexing of the RTP stream packets over the end-to-and media transfer. Although the conventional method of using TCRTP(Tunneling Multiplexed Compressed RTP) is an efficient mettled of maximizing tile network throughput, it is inadequate for the All-IP based end-to-end communication. The method is a link-layer independent solution that can be easily implemented in the NGN(Next Generation Network).
-
In this paper, we studied a now VDSL frequency plan mode 6 for improved\ulcorner symmetric 10MDSL service. The frequency plan 998 for asymmetric and frequency plan 997 for symmetric have arc not optimally designed for 10MDSL service. To improve reach and rates of 10MDSL, we proposed for a now frequency plan. According to the results of our simulation studios of newly Proposed mode 6 frequency plan which compared to plan 998, 997, and ethers[2], the new scheme gives an improved performance in rates and reach.
-
In this paper, we consider a generalized rule of retransmission request, identified as (Μ,
$\sigma$ ) rule for multicopy transmission ARQ. Following a revised rule to conform with a strict criterion for requesting a retransmission, we can reduce the probability that a packet accepted by the receiving node is still being infected with errors. In turn, such amendment invokes a degradation of delay and throughput performance. For a quantitative evaluation of (Μ,$\sigma$ ) rule, we develop an analytical method to calculate probability of error remains, maximum throughput, average and peak delays, and delay variation. From the numerical examples made by use of the analytical method, we observe a performance trade-off between probability of error remains and delay/throughput. We also confirm the adaptability of (Μ,$\sigma$ ) rule to meet various QoS requirements. -
In this paper, we study the improved bounds on the performance of low-density parity-check (LDPC) codes over binary-input additive white Gaussian noise (AWGN) channels with belief propagation (BP) decoding in log domain. We define an extended Gallager ensemble based on a new method of constructing parity check matrix and make use of this way to improve upper bound of LDPC codes. At the same time, many simulation results are presented in this paper. These results indicate the extended Gallager ensembles based on Hamming codes have typical minimum distance ratio, which is very close to the asymptotic Gilbert Varshamov bound and the superior performance which is better than the original Gallager ensembles.
-
In this paper, we have analyzed transmission time for WAP over CDMA using turbo code scheme. In order for SAR to improve the transfer capability, the transmission of messages have been simulated using a fragmentation that begins with the total package and incremental fragmentation for each layer using the WTP to define tile resultant packet size and the level of fragmentation for each proceeding layer. This turbo code scheme decreases transmission lime of RLP baseband packets. From the results, we arc able to obtain packet transmission time and optimal WTP packet size for WAP over CDMA in a Rician fading channel.
-
This paper discribes the differen-ces between making handset sample and handset massproductions. To save time during mass production, Calibrat-ion should be automated and SW do-wnloading also be automated and Par-allely done. All this processes are des-cribed here. Especially Calibration are more detaily explained in this paper.
-
For high data rate transmission over wireless fading channels, space-time trellis ceding techniques can be employed to increase the Information capacity of the communication system dramatically. In this paper, we consider the concatenated space time LDPC (Low Density Parity Check) codes. Extra ceding gains In addition to the diversity advantage is shown to be achieved for certain space-time trellis codes transmitted over quasi-static lading channels.
-
In this paper, the structure of OFDM system is studied, and causes of inter carrier interference (ICI) are analyzed. Based on analysis, this paper shows a technique to prevent a distortion due to nonlinearity of high Power amplifier. The proposed scheme is a predistorter for high power amplifier linearization in orthogonal frequency division multiplexing (OFDM) system used in wireless local area network(WLAN). This is verified by comparing BER characteristics of OFDM system, between used PD and not used PD.
-
This paper presents a Prototype system developed for a Bluetooth interfaced VoIP system. The VoIP phone is developed based on tile implementation of a CELP coder on the TI 16bit DSP Processor A PC interfaced with Bluetooth module is used to designing a access point system. Host controller protocol stack is implemented to realize gateway between the wireless and wired line networks. A server application program for user management and call processing, which is based on TCP/IP peer to peer connection, is implemented for tile evaluation of overall interface system.
-
In the input buffer switch system, VOQ(Virtual Output Queue) archives 100% throughput. The VOQ with the systolic architecture maintains an uniform performance regardless of a number of Packet class and output port, so that it doesn't have a limitation of scalability. In spite of these advantages, the systolic architecture VOQ is difficult to change sorting order In this paper, we Proposed a systolic architecture VOQ which support weighted round robin(WRR) algorithm to provide with flow control service.
-
NAPTR(Naming Authority Pointer) is a type of resource record specified IETF RFC 2915. NAPTR enables to register various services in tile domain name systems and thus Provides a way to discover services available on specific hosts. This paper describes the design and implementation of a proxy DNS system aimed at supporting NAPTRS. The goal of this work is to study on the feasibility of the service discovery registered in DNS via NAPTR records. This research result can be applied to service discovery in the resource information management for high performance GRID environments as well as to implement generic ENUM services
-
This paper describe the passive intermodulation products(PIMs) which are formed in high power Ku-band transponder and antenna subsystem on the Communication St Broadcasting Satellite(CBS)program when two transmit carriers beat together to generate harmonics that fall into the receive band. How the PIMs are initially generated and the effect of PIMs for Ku-Band payload system are analyzed by calculating the PIMs frequencies and the power level of PIMs.
-
In this paper, we propose a structure of 800bps high speed router and a gigabit Ethernet line interface board. Having Programmability, network processor is applied to gjgabit Ethernet line interface board. Also, we propose a new method to upgrade image files that consist of operating system and drivers. It is possible to upgrade image files for several boards at once and to reduce the elapsed time for image upgrade using tile proposed method.
-
In this paper, we present a Ku-band OMT(orthomode transducer) structure employing a simple waveguide transition withou a septum. Various aspects of the OMT design are discussed. The design is carried out using a commercial software HFSSe The designed OMT shows good characteristics over 12.5114.25 CHz frequency bands.
-
In this paper, we propose a new node architecture LonWorh control Network for home network system environmint using power line communications. Using conventional Lon Work technology is a many disputable points for home network. LonWork network system needs high-cost development equipment. Moreover, conventional Lon Work system can not implement high-grade algorithms and variety application operation. because of the limitation of processing ability in Neuron chip. For that reason, the proposed structure is applicable to low-cost and more complex applications which are impossible in home network using conventional Lonworks structure. The proposed structure is implemented with some hardware and かone software for power line home network. The physical layer and the MAC layer of the LonTalk protocol within ton Work are implemented in hardware, which decreases the development costs communication processor. The upper of link layer of the LonTalk protocol is implemented with software, which decreases the development costs of software and increases the flexibility of tile system and increases the extension of the system. We verified the commercial feasibility of the proposed system through the power line tests with the existing LonWorks network in home network. As a result, it is concluded that the proposed architecture provides increasing flexibility and decreasing cost of the system.
-
The optimal AP placement for wireless LAN is important factor for improving service quality and reducing cost. Logical area property, which is user's frequently posed place, must be considerated for flexible design. This paper proposes optimal multiple AP placement method based on path loss model which is one of radio prediction tool. The proposed method can got flexibility in multiple AP placement using user's defined parameter and tile optimization design uses Hopfield network algorithm The result of simulation shows that the proposed optimization design of multiple AP placement can improve service quality for wireless LAN.
-
This paper describes tile design and implementation of contact and contactless If card OS(Operating System) for Java Card, namely JCOS(Java Card 05). The JCOS complies with ISO/IEC 7816 and IS0/1EC 14443 standards. The JCOS conforms to Java Card 2.1.2 specifications. The JCOS is running on 32-bit ARMTTDMI with public key crypto-coprocssor. This paper describes only the dual-interface protocol of the JCOS which supports contact and contactless applications in a single chip. The JCOS has been completed with our sample banking service and access control service in ETRI up to now.
-
This paper describes an experiment on the embedded network agent. The embedded network agent is the device that will enable other devices to communicate over the Internet. Many devices have no way to communicate with other devices over the Internet The embedded network agent extends the stand-alone devices that have no TCP/IP protocol suite to the Internet, the global networks, without any hardware and software. To support the better efficiency, this parer proffers new TCP state diagram of the embedded network agent. This TCP state on the embedded network agent considers the status of the common devices behind the embedded network agent. Because of this consideration, the embedded network agent tenders an improved result to user.
-
The goal of this study is to realize the PBG lowpass filter using novel PBG structure modification both upper layer and ground layer. It has been designed three aperture slots of ground layer for PBG structure which the center slot shape of ground is two type, rectangular and dumbbell. This PBG LPF llas the character of the broader stopband and smaller size than typical LPF. The measurement results have matched the simulated ones. It has the cutoff frequency of each 4.4650Hz and 3.520Hz and at least -2OdB of the signal suppression at the stopband.
-
본 논문에서는 ITS(Intelligent Transport System) 서비스를 위한 기반시설로 대전광역시에서 도입한 DSRC(Dedicated Short Range Communication) 시스템에 대하여 DSRC 시스템의 개요, DSRC프로토콜 및 DSRC시스템을 이용한 Mobile IP서비스 제공 방법에 대하여 제안하였다.
-
Because of great damages by illegal hacking, demand for security of the public network as well as the private is seemingly limitless. This critic리 requirement is leading ISPS to deploy new security services for their customers. In this paper, we present active responses for the security of a ISP's network, and describe the deployment of a new security service using the network secured by that responses.
-
본 논문은 Global loaming, backward compatibility, 그리고 multi-standard가 요구되는 미래의 통신시스템에 대한 해답인 Software Defined Radio에 관한 글로서 SDR의 개념과, 그 접근 방법에 대해서 논하고자 한다. 특히 3세대 이동통신인 WCDMA system을 모델로 하여, 그 접근방법에 대해 살펴본다. SDR의 발전은 크기, 무게, 전력소모의 문제와, 전용의 하드웨어 없이 동작할 때의 성능저하를 문제를 해결해야 한다. 여기서 그 해결방안으로 SoC와 Multi-CPU의 방법을 제시하고자 한다.
-
이 논문은 흠네트워크에 있어서 전력선 통신의 채널 모델을 제안하였다. 전력선 통신의 특성은 노이즈, 감쇄현상, 위상변이를 고려해야만 한다. 본 연구에서는 노이즈 및 감쇄현상을 고려한 각각의 모델을 제시하였고 주파수 특성의 시뮬레이션을 통하여 모델의 유용성을 입증하였다.
-
To support Internet traffic efficiently over ATM \networks, Guaranteed Frame Rate(GFR) has been proposed in tile ATM Forum to ensure minimum rate guarantees to VCs. In this paper, we proposed fuzzy logic based buffer management algorithm that provides MCR guarantee and fair sharing to GFR VCs. A key feature of proposed algorithm is its ability to accept or drop a new incoming packet dynamically based on buffer condition and load rate of VCs. This is achieved by using fuzzy logic controller for the production of a drop factor. Simulation result shows that proposed scheme significantly has improved fairness and TCP throughput compared with previous schemes.
-
The software complexity model makes an estimated of the product software. For a practice of software managed, need to guideline of the static analysis. Especially, Software complexity model introduced for the estimation of software quantity. In case of measurement the software matrices, its need for us to analysis of software qualify and products. In this paper, we represent that the analysis of function point, control structure and interface, volume matrices in various aspect of switching software. Others, their results utilized similar of project and system development.
-
중앙집중식 구조의 기존 내용기반 요구분산의 문제점인 확장성 및 성능을 향상시키기 위해, 본 논문에서 는 2단계로 구성된 분산구조로 된 L4/L7 방법을 사용한다. L4 스위치를 이용하여 1차적으로 부하를 분산시키고, 이들에 대해 Proxy의 성능상의 단점을 보완한 TCP splicing을 적용하여 2차로 L7 스위치 기능을 수행하도록 한다. 리눅스 환경에서 제안한 시스템을 구현하고 클러스터형 웹서버 시스템을 구성하여 실험하였다. 제안한 분산구조 방법이 중앙집중 방식에 비해 확장성, 성능면에서 우수함을 확인하였다.
-
In this paper, we implemented a SDH synchronous network system based on ITU-T recommendation G.707 - Network node interface for the synchronous digital archy(SDH). For the system, we used signal processing SDH ASIC, and designed a FPGA_Control chip for various signal control and a FPGA_Alignment cllip for data alignment using YHDL(Very high speed integrated circuit Hardware Description Language). For system monitoring, an operation system was developed using ANSI C and executed in CPU (Motorola MPC-860). The system was evaluated by using ANT-20 for data transmission error defection, jitter detection, pointer chocking, and overhead determination.
-
Undoped-GaN thin film is deposited on Sapphire substrate by MOCVD. SAW velocity is measured with tile center frequency by HP8753C. Center frequency is 266.52 MHz and SAW velocity is 5330㎧ when wavelength was 20 Um. insertion loss, Q factor and side love attenuation is 41.265 dB, 257.41 and over 23 dB. k'i is calculated from tile measured data. k2'is from 1 % to 4 %. TCF is -61.817pp/m/
$^{\circ}C$ . -
This paper has been studied a new geoelectric survey and instrunmentation using Low Frequency Electric Field .sensing Antenna. “Low Frequency Electric Field Sensing” is a technology in new method of survey to use array type antenna, the power of operation in antenna is using AC or DC pulse instead of DC current. The architecture of system embodied transceiver system using a microprocessor(PIC) of Microcllip Technology Inc. An array antenna design and il control transmission of antenna to use CDMA in this system. It is using array type antenna for the earth、earth's crust to survey explain from theory and experience.
-
In this paper, The resonant frequencies of any modes in the dielectric resonator filter is determined by numberical analysis. The theoretical analysis for the dielectric resonator filter used Ansoft HFSS. We designed the dielectric resonator filter with resonant frequency 4.5 GHz. We describe the characteristics of delivering Power to resonator in different shaped coupling loops. Tile resonant mode of T
$E_{01{\delta}}$ and T$E_{01{\delta}}$ could be selected by the horizontal and the vertical coupling loop.p. -
A design of Ku-band(11.7~12.20Hz) monolithic microwave integrated circuit(MMIC) low noise block(LNB) downconverter using self oscillating mixer (SOM) for direct broadcast satellite(DBS) application is presented The proposed LNB downconverter is composed of low noise amplifier(LNA), image reject filter(IRF), SOM , low pass filter(LPF). The conversion gain is 30dB , VSn is less than 1.7: 1 and overall noise figure is less than 1.2dB.
-
We present in this Paper a microwave Power sensor fabricated by a standard CMOS process and a bulk micromachining process. The sensor consists of a CPW transmission line, a resistor as a healer, and thermocouple arrays. An input microwave heater, the resistor so that the temperature rises proportionally to the microwave power and tile thermocouple arrays convert it to an electrical signal. The sensor uses air bridged 8round of CPW realized by wire bonding to reduce tile device size and cost and to improve the thermal impedance. Al/poly-Si junctions are used for the thermocouples. Poly-Si is used for tile resister and Aluminium is for transmission line. The resistor and hot junctions of the thermocouples are placed on a low stress silicon nitride diaphragm to minimize a thermal loss. The fabricated device operates properly from 1㎼ to 100㎽\ulcorner of input power. The sensitivity was measured to be ,3.2~4.7 V/W.
-
In this paper, we present a new design method for a square iris polarizer to be used in dual-band (Ka-band; 20.8 ~21.2 ㎓, 30.6~31 ㎓) antenna feeds. Principles of operation of a square iris polarizer, its design concepts and methods are proposed. Based on proposed methods, a Ka- band polarizer with -35 dB return loss and 0.3 dB axial ratio is designed using the commercial software HFSS.
-
In this paper, we present design methods for a series-fed microstrip patch array operating at X-band frequency. The array consists of 18 rectangular patches connected to 3 quarter-wave impedance transformers. The power divider is designed for the uniform element excitation. The element excitation is then made to be tapered by increasing the input impedance of elements located at array edges. The designed antenna is fabricated and tested. Results of test show a fair agreement with the prediction.
-
In this paper, a low-noise amplifier is designed and fabricated using the HJFET for the reception of the Ku-band satellite broadcast signals. The optimum input and output reflection coefficients of each amplifier stage are obtained by the trade-off between the stable gain and the noise figure circle. The amplifier performance is simulated and optimized using a microwave CAD software. The designed amplifier is fabricated and tested. Results of the test show a gain of 17.0 dB, a gain flatness of less than
$\pm$ 2.BdB, the noise figure of less than 1.0 dB, and the input and output reflection coefficient of less than -10 dB. -
Design methods are presented for an X-band traveling-wave slot array realized on a rectangular waveguide. An array of 21 longitudinal slots is realized on the broad wall of a rectangular waveguide. The squint of the antenna main beam is adjusted using the element spacing and the waveguide broad wall dimension. The excitation of the array is controlled by the slot offset from the waveguide center line Multiple I-plane steps are placed around last slot elements so that the second-order beam due to tile reflected wave Is minimized A waveguide-to-coaxial adapter Is designed for feeding the array antenna from a coaxial system. Results of the design show an outstanding performance of the antenna 17.1 dB gain. 36"beam 1111, and -21 dB maximum sidelobe level.evel.