A non-thermal plasma process combined with $Cr_2O_3/TiO_2$ catalyst was applied to the decomposition of trichloroethylene (TCE). A dielectric barrier discharge reactor operated with AC high voltage was used as the non-thermal plasma reactor. The effects of reaction temperature and input power on the decomposition of TCE and the formation of byproducts including HCl, $Cl_2$, CO, NO, $NO_2$ and $O_3$ were examined. At an identical input power, the increase in the reaction temperature from 373 K to 473 K decreased the decomposition of TCE in the plasma reactor. The presence of the catalyst downstream the plasma reactor not only enhanced the decomposition of TCE but also affected the distribution of byproducts, significantly. However, synergistic effect as a result of the combination of non-thermal plasma with catalyst was not observed, i.e., the TCE decomposition efficiency in this plasma-catalyst combination system was almost similar to the sum of those obtained with each process.

This study proposes a mathematical model to characterize the removal of nitrogen oxides in a dielectric barrier discharge plasma process. As well as the reactions between nitrogen oxides, water vapor, oxygen and nitrogen, the model takes into account the effect of ethylene often used as a chemical additive to reduce the power consumption of the process on the removal of nitrogen oxides. Since the concentrations of the radicals concerned in the main reactions including O, OH, H and N should be calculated to predict the removal efficiency of nitrogen oxides, they were theoretically derived. The parameters affecting the removal of nitrogen oxides, such as initial concentration, discharge power, humidity, and ethylene concentration were experimentally evaluated, which were compared with the calculated results to verify the validity of the model proposed. The predicted concentrations of several byproducts formed in this process were also presented and discussed. The effects of several parameters mentioned above on the removal of nitrogen oxides were reasonable described by the proposed model.

Interfacial crack problems between fiber and matrix in composite materials are discussed. A series of interfacial crack initiation and propagation experiments are conducted using the biaxial loading device for various mode-mixes. Normal crack opening displacement (NCOD) is measured near crack front by a crack opening interferometry and used for extracting fracture parameters. From mixed mode interfacial crack initiation experiments, large increase in toughness with shear components is observed. Initial velocity of crack propagation is very dependent upon the mode-mixes. It increased with positive mode-mix due to the increase of stress singularities ahead of crack front and decreased with negative mode-mix resulting from the increase of the degree of compressive stress behind the crack front. Crack propagation was less accelerated with positive mode-mix than the negative mode-mix.

This research is for the relationship with heat treatment cooling temprature and the characteristic of Mechanical properties of Boron-Addition-Steel, the main material and SM25C steel, the sub material, structure viewing fractography, hardness test, tensite test and are carried out after the manufacturing small-specimen treated with heat of $750^{\circ}C$, $850^{\circ}C$, $1050^{\circ}C$. The influence to the Mechanical properties accompanied by AISI51B20, Boron-Addition-steel shows the following result. 1. The influenc of heat treatment by the content of cabon-steel is dominant. Addition of boron result is Strengthening structure effectively by segregation and improving over all mechanical characters such as good. it results from the increase of temacity by the stability of inter granular with improvement of harden-ability. 2. Boron-Addition-Steel exist in the from of martensite structure accompanied by the ferrite precipitition centering around grain boundary, and is improved to Hv 200. 3. The height of harden-ability and fatigue stress the influence of heat results from crystal structure of martensite by difference of strength level in the structure of ferrite and doesn't have am effect on sensibility of temperature, and turns out to defend on production and growth of Matrix-structure-factor.

A technique for the design of cooling tower fans with sweep is presented. This technique is developed using the equations for the one dimensional inviscid flow through the fan blade, the empirical equations, and the experimental correlations. A parabolic function is used to generate a sweep of the fan. Design data for the fan and the balde can be obtained for a given flow rate and a pressure rise. Also, the present method is used to construct the three dimensional model for the designed fan. Design data and the model show general characteristics of the axial propeller fan.

The purpose of this is to evaluate Hakui Stream Naturalness Index(S.N.I). and to find out stats, problems and opportunities of the Hakui stream by assessment standard. Assessment standard is mainly based on physical structure of stream environment. The purpose evaluating sectors and elements are physical form and structure restoration of stream. To find out assessment standard of stream naturalness index, conceptual frame of assessment standard has been established, for which four sections, for example, longitudinal section, lateral section, stream bottom structure and water environment, have been selected. Overall stream naturalness index of the Hakui stream has been distributed at 3rd to 4th grade, and its assessment index accounted for 3.2 to be 3rd grade, and its mode also did 3rd grade. Stream naturalness index of each section was as follows: Longitudinal section index accounted for 3.6 in average to be 4th grade, and later section index did 3.0 to be 3rd grade, and stream bottom structure index did 3.0 to be 3rd grade, and water environment index did 2.7 to be 3rd grade. Analysis of assessment outcome of stream naturalness index has checked status, Problems and opportunities of corresponding stream. Assessment of stream naturalness index of the study provides useful information for restoration of close-to-nature stream, and furthermore has its meaning in checking problems and opportunities of Hakui stream.

This paper described the characteristics of the exhaust pressure and proposed the assistant device for detection of misfired cylinder. Misfire, one of abnormal combustion, affects a bad influence of the 3-way catalyst and emits unburned hydrocarbon. Therefore, to prevent these unusual phenomena and eliminate the factor of the environmental pollution, early detection and correction of the misfired cylinder play a very important role. The configuration of assistant device was changed by length and diameter of pipe and analyzed with the install position on the exhaust system. Experimental results showed that the configuration of assistant device is not affected more than length and diameter of pipe and the assistant device is be effective in the detection of misfired cylinder on the gasoline engine.

This paper proposed new techniques of rotor position detection for 8/6 pole Switched Reluctance Motor(SRM). This technique is very simple and easy to find out rotor position. The main idea uses the impulse responses which have different values between aligned and unaligned rotor position. In order to obtain the informations of the rotor position, the impulse applied to the unenergized phases and their responses are analyzed to control the speed of SRM without shaft sensor. Experimental results verify the feasibility of the proposed method.

The purpose of this thesis is to develop a simulation model to estimate link travel speed applicable to urban street transportation planning for interrupted traffic flow, influenced by signalized intersection. This link travel speed model is expected to be a better and more than previous studies.

Fe(II)하에서 분자산소에 의한 기질의 산화는 헴에 의해 나타난 가역산화반응에 의해서 대단한 생물학적 흥미가 있다. 적당한 조건하에서 산화되어진 리간드로서 염인 피리딘이나 아마이드, 그리고 두 가지 종류의 Fe(II)-acac나 Fe(II)-sal의 complex와 산화되는 기질의 성질이 비라디칼 조건하에서 안정하다는 것을 알았다.

1. The objective of this paper is to investigate the indoor environment from the viewpoint of interaction between physical environment and the human responses. 2. A continuous measurement has been carried out for 1 year and distribution of variables have been measured for 1 day. 3. The attitude of workers was investigated by a questionnaire. 4. As the result, average luminance represented more than 800-1800 lx in the office, in contrast with less than 1000 lx in the encourage luminance of an office. 5. There was a significant difference of the occupants' response to the light environment between the neighboring environments. 6. Measured thermal conditions are on the edge of the ASHRAE comfort envelope in summer, and in the neighborhood of the lower dry limit of the envelope in spring.

Most sensor array signal processing methods for multiple source localization require knowledge of the correct shape of array(the correct positions of sensors that consist array), because sensor position uncertainty can severely degrade the performance of array signal processing. In particular, it is assumed that the correct positions of the sensors are known, but the known positions may not represent the true sensor positions. Various algorithms have been proposed for 2-D sensor array shape calibration in far field environment. However, they are not available in near field. In this paper, 3-D sensor array shape calibration algorithm is proposed, which is available in near field.

In order to determine the effective way of measuring the Mode I stress intensity factor for a material containing a two-dimensional surface crack by means of the alternating current potential drop(ACPD) technique, the change in magnetic flux density between crack surfaces and above the specimen surface due to load was studied theoretically. The magnetic flux density in the air between crack surfaces is uniform and above the specimen surface is not changed by increasing the load in the material. Therefore, the change in potential drop due to load in a measuring system which was designed to induce a large amount of electro-motive force was caused by the change in internal inductance of material, the change in the mutual inductance between internal inductance of material and measuring system and the change in the mutual inductance between internal inductance of material and power supply line.

An experimental investigation was performed to study the characteristics of laminar water flow in a horizontal circular tube by using liquid crystal. A simultaneous measurement technique has been employed to measure the temperature field in a two-dimensional cross section of fluid flow. This study found the temperature distribution for Re =900~1,500 along longitudinal sections and the results appear to be physically reasonable. To determine some characteristics of the laminar flow, 2D PIV technique is employed for temperature measurement and liquid crystal is used for heat transfer experiments in water. The experimental rig was manufactured from an acryle tube. The test tube diameter of 25mm, and a length of 1200mm. The used algorithm is the gray level cross-correlation method by using Kimura et al. in 1986.

The goal of this research is to develop a Heel/Side Laster and control GUI(Graphic User Interface) for adaptive manufacturing. For this purpose, we have analyzed the working sequences of heel/side laster, and developed a control program that will facilitate the machineries with functions that are suitable for adaptive manufacturing. We also made it possible to modify the gluing path with simple manipulation of CAD data. By providing a user-friendly GUI, we made it possible for unskilled workers use the system without difficulty. In addition, we have developed a flexible environment where the already available CAD data can be modified and saved with ease. Automatic feeding and path control algorithms for thermoplastic cement were also implemented. By using the Heel/Side Laster for adaptive manufacturing, we are able to achieve increased productivity and work efficiency while improving the quality of the product with self-diagnosis and fine adjustment function.

The change of crystalline structure and mechanical properties of PET filaments were investigated. Samples were treated by isothermally annealed after elevated heating. Measurements were carried out of density gradient tube for crystallinity and UTM for initial modulus and yield stress. Isothermally heat treatment were carried out $100^{\circ}C$, $120^{\circ}C$, $140^{\circ}C$ for 10min., 30min., 60min, in silicon oil bath. And isothermally heat treatment after elevated heating from $20^{\circ}C$ were carried out $100^{\circ}C$, $120^{\circ}C$, $140^{\circ}C$ for 10min., 30min., 60min., with heating rate of $5^{\circ}C/min$., $10^{\circ}C/min$. From the results of this study, it found the following facts. It was found that the crystallinity, initial modulus and yield stress of samples were increased with increasing of annealed temperature and time. Also crystallinity, initial modulus and yield stress of samples which were isothermally annealed after elevated heating from $20^{\circ}C$ were larger than those of isohtermally annealed samples.

In this paper, a self-organizing fuzzy logic controller with hybrid structure is proposed. The structure of the proposed method is composed of a basic fuzzy logic controller and the FARMA SOC(Fuzzy Autoregressive Moving Average Self-organizing Controller). The self-organizing cntroller with hybrid structure has advantage over the FARMA controller as follows. The proposed controller improves poor performance due to the lack of I/O data to calculate predictive output. I executed some computer simulations on the regulation problem of an inverted pendulum system and compared the results of the proposed method with those of the FARMA SOC method.

In most resource reservation strategies, which give higher priorities to handoff calls over new calls, new calls are often blocked even though there is plenty of available reserved resource. This causes inefficient resource utilization, especially when there are not so many handoff attempts. In this paper, we propose a new reservationstrategy called soft reservation in which new calls can be allocated to the reserved resource while maintaining the QoS of handoff acceptable. Using an M/M/c/c queuing model, we can see that the proposed strategy provides better performance than the conventional reservation strategy in terms of blocking probability of new call and dropping probability of handoff calls.

Children of three-to-eighteen-years-old have been brought up in the institution (Orphanage) for several reasons such as family dissoultion, divorce and poverty since the Korean War of 1950. The Cottage, where these children are housed and brought up has dining room, living room and bedrooms. Psychological aspects of children are being observed distracted and differentiated to some degree according to the sizes of bedroom floor spaces ranging from 2.3 square meters to 9.0 square meters per child. Since the most facilities were built during the 1950-1960s period, most of the cottages are now in the condition of being rebuilt or remodelled. This study was conducted to obtain some basic data necessary for design of spaces in the orphanages by examining the relations between the meal and sleeping activities of children and residence types.

We can take 'Profit security', in the field Process improvement activity and man-power upgrade in the learning of organization activity or upgrading ability of each peoples. After Tayler System(Scientific Management in1911) and Ford System(Conveyor system in 1913), Toyota System(Ohno's TPS; Toyota Production System around 1980) which was developed by Toyota in Japan in the third productive revolution. This thesis study on the focus of 2 successful examples(P and S companies in Seong-Seo industrial complex Tae-Gu city) which introduce Toyota system can apply to VM(Visual Management), 3jeong(Right Products Right Quantity, Right Box and Right Position)5S(Seiri, Seiton, Seisoh Seiketsu, Sitsuke), JIT(Just In Time), KAIZEN(Improvement), KANBAN System(Logistic) and output of Factory. For examples P company obtained a lot of results(productivity increase 19%, Quality up 46%-36ppm, storage decrease 25% per year), S company obtained a lot of results(productivity increase 20%, Quality up 40%, storage decrease 33% per year, 2600 improvements in 2002. In conclusion Korean KANBAN system (modified Toyota System) is similar to exchange of work as Korean traditional system in agriculture as like dure 'PUMASHI' SANGBU-SANJO) that's autonomous management systems. In conclusion Korea KANBAN system needs apply to not only all the manufacturing industry but also the various fields of industry.