Many products related to automobile and airplane have been manufactured by semi-solid process. There are many parameters in semi-solid process such as punch velocity, die temperature, and solid fraction of material. Among these parameters, solid fraction of material is one of the most important factors to determine quality of product. To obtain solid fraction of a certain semi-solid product is very necessary and useful for inspecting and analyzing the product. In this paper, image analysis program for microstructure by semi-solid forming process has been developed with the simple apparatus such as a personal computer and scanner, instead of expensive image analyzer.

This study was carried out to investigate the feasibility of the used frying oil as a bin-oil which was one of the alternative fuel for diesel engine. From tests of engine performance, it was shown that the bio-oil and blends and the sufficient potential as alternative fuels of diesel engine except NOx and Smoke emission.

A method for the control of pulsating pressure transients in the hydraulic brake system has been presented and experimentally verified. This control is accomplished by installing flow restricting devices at appropriate locations in the brake oil pipe line. The experimental results presented are expected to provide a basis for transient control design of hydraulic brake systems.

Refining of powder particles and their dissolution into the Al matrix during mechanical alloying(MA) were investigated by using X-ray diffraction(XRD) transmission electron microscopy (TEM) functions of alloy composition, milling time and ball to powder ratio(BPR). It is found that Ti particles less than 20nm are observed in a dark field image of mechanically alloyed Al-10wt%Ti whose XHD pattern exhibits no Ti peak. The observed change of lattice constant of AI indicates that about 1 wt%Ti can he solved in Al after MA for a long time, independent of alloy composition, milling time and BPR, suggesting that most of Ti particles arc retained in the Al matrix. It is concluded that the disappearance of XRD peaks in mechanically alloyed Al-10wt%Ti is not simply attributable to the dissolution of Ti into Al, but associated mainly with extreme refining and/or heavy straining of Ti Particles.

A spectral measurement system for reflection and transmission properties by using an optical fiber and an ellipsoidal mirror was newly developed. The hemispherical reflectance and transmittance spectra of several heating resisting ceramics materials were measured from visible to middle infrared region. The directional characteristics of reflection and transmission were also investigated in consideration of the absorptance. The measured data were analyzed by using a four flux model of radiation transfer, The radiation properties could be estimated by the obtained scattering and absorption coefficient spectra.

This study developed signal optimization algorithm by analyzing vehicle arrival patterns. The major principle of signal optimization is dissipate all queueing vehicle in 1cycle and assign delay time uniformly for all approaches. For this, this study used optimal green time and surplus green time. Optimal green time calculated by estimated traffic volume from vehicle arrival model. Surplus green time defined as the gap of optimal green time and queue dissipated time. And alternative cycle has minimum surplus green time was selected as the optimal cycle. Finally, total delay and average delay per vehicle can be calculated by using queueing theory.

This study examines the effects of removal of the sediment protection weir at Taehwa river mouth on hydraulic and around river environment considering the fact that the effects of the sediment protection weir which is installed to protect water level drop of Ulsan harbor caused by sediments according to flood in Taehwa river, Dong-chun, and so forth may add water quality contamination by flow stagnance in normal and drought period and accumulation of pollutants. The result is as follows. First, it is estimated from the examination of variation characteristics water depth and level for Taehwa river before and after removal of the sediment protection weir that about 0.01m of water depth down according to removal of the sediment protection weir occurs when low flow runs between the sediment protection weir which is located about 2.3km away from the estuary and Samho-gyo which is about 9.0km away from the sediment protection weir, and about 0.01~0.56m(directly upstream point of the sediment protection weir 0.56m, Myongchon-gyo 0.14m, Ulsan-gyo 0.03m, and Taehwa-gyo 0.02m) downs when design flood flows between the sediment protection weir and the upstream of Taehwa-gyo which is 10km away from the sediment protection weir. Therefore, it is thought that variation of hydraulic characteristics of water depth down and so on according to removal of the sediment protection weir is slight because water depth variation is only about 1cm between directly upstream point of the sediment protection weir and Samho-gyo. Next, it is estimated from the examination of variation characteristics of flow velocity for Taehwa river before and after removal of the sediment protection weir that about 0.0lm/s of flow velocity increase occurs between the directly upstream point of the sediment protection weir which is about 2.4km away from the estuary and the directly upstream point of Samho-gyo when low flow runs, and about 0.01~0.44m/s increases between the sediment protection weir and Samho-gyo when design flood flows. Therefore, riverbed erosion by the increased flow velocity is concerned but it is thought that the concern about riverbed erosion is not great because the mean velocity is about 0.07~1.36m/s when low flow runs, and about 1.02~2.41m/s when design flood flows for the sector which experiences the flow velocity variation.

Polycarbonate(PC) membranes for oxygen enrichment from air were prepared by the wet phase inversion method. In order to improve oxygen separation performances of the PC membrane, the effect of the added ethanol(nonsolvent) and $CuCl_2$(metal salt) concentration in the casting solution on morphology, oxygen permeability ami $O_2/N_2$ separation factor of the membrane was studied. In addition, tensile strength and elongation at break of the membrane were investigated. An asymmetric membrane with a dense top layer and a porous sublayer was obtained. The thickness of the dense top layer decreased with increasing amount of nonsolvent additive. Compared with pure PC membrane without additive(metal salt), the oxygen permeability and $O_2/N_2$ separation factor of the $PC/CuCl_2$ membrane are significantly improved. The oxygen permeability and $O_2/N_2$ separation factor is $5.25{\times}10^{-9}cm^3(STP){\cdot}cm/cm^2{\cdot}sec{\cdot}cmHg$ and 4.5, respectively. This improvement might be due to good interaction between metal salt and oxygen.

This study investigates the relationship between size of cosmetic shops, size of showcases, sorts and arrangement of light source, floor plan, and illuminance measured of interior space. From this result, the average space size of cosmetic shops were $623.2{\times}512.9{\times}258.1cm$(width, length, height), the average space size of showcases were $273.3{\times}53.8{\times}89.5cm$ (width, depth, height). The light source was most frequently used fluorescent lamp, and illuminance was the most highest nearby main showcase, and average illuminance were 722[Ix], uniformity were 0.3.

This paper was to investigate the preparation of polysulfone(PS), polyethersulfone(PES) and polyphenylsulfone(PPS) membrane. The thermal property of PPS was higher than that of others. From the result of SEM, the concentration of polymer was found to have a significant effect on the structure of membrane, and the structure of membrane made of PES is found to have regular micell form of asymmetry. Permeability and selectivity for oxygen and nitrogen gas in the air were analyzed by GC. Permeabilities of the membrane made of PES for oxygen and nitrogen in air, 1.5 and $0.7(x10^9[cm^3(STP)cm/cm^2seccmHg]) $, respectively was higher than that of others. and Selectivity of the membrane made of PPS for oxygen to nitrogen gas in air was 2.9.

In multibody dynamics, differential and algebraic equations which can satisfy both equation of motion and kinematic constraint equation should be solved. To solve this equation, coordinate partitioning method and constraint stabilization method are commonly used. The coordinate partitioning method divides the coordinate into independent and dependent coordinates. The most typical coordinate partitioning method arc LU decomposition, QR decomposition, projection method and SVD(sigular value decomposition).The objective of this research is to find a efficient coordinate partitioning method in flexible multibody systems and a hybrid decomposition algorithm which employs both LU and projection methods is proposed. The accuracy of the solution algorithm is checked with a slider-crank mechanism.