This paper presented a new model of virtualized CNC milling machine. The model verifies the over cut, the under cut and the surface roughness using NC file generated from CAM and cutting condition. The model uses Z-map model to verify workpiece. In this paper, the model used the velocities of x, y and z direction and obtained a center point of a hall end mill for modeling Z-map of workpiece. To investigate the performance of the model, simulation study was carried out. As the results, the model gave geometry accuracy of workpiece, the surface roughness and the chip loads in finish cutting that can predict tool chipping. The virtualized CNC machine can he used a flat end mill, a ball end mill and a rounded end mill.

This paper proposes a method to detect the misfired cylinder using a new misfire detection index. The new method of misfired cylinder is a comparison of pressure gradient during the blowdown period of exhaust stroke. If a misfire occurs, the engine will he lost some power and consumes the more fuel and the torque will be unsteady. Most of all, the misfire affects a bad influence of the 3-way catalyst and emits unburned hydrocarbon in the air. To prevent these unusual phenomena and eliminate the factor of the environmental pollution, it is important to detect the misfired cylinder. To do the experiment, set up the assist device on the manifold. This assist device is not deformed for conventional exhaust manifold and installed in the end of the exhaust manifold. Experimental results showed that the method using the mean gradient pressure index is proven to be effective in the detection of misfired cylinder on gasoline engine regardless loads and revolutions of the engine.

The lower toughness or brittle materials for mechanical test lead to the additional requirement that applied displacements be controlled with high resolution. Biaxial tension and shear tester using stepper motor with harmonic driver is shown. The device had to be high resolution so that the crack initiation process of slow extension and steady growth could be examined, Grip plates were connected to a linear bearing and actuator. The actuators consisted of stepper motors with harmonic driver connected to pre-loaded ball screw and nut assemblies. The encoders and motor controllers were connected to a personal computer so that arbitrary displacements histories could he prescribed in normal and tangential directions. The linear bearings were used to react loads perpendicular to their axes while allowing low friction, parallel movement of the attached grips. Load cells measured the reactions normal and tangential. the loads measured the reactions were recorded by the computer.

The flow characteristics on the centerline in case of free jet, sudden expansion jet and impinging jet have been investigated. Centerline flow behaviors and similaritis with mean velocities, turbulent intensities, shear stresses, isotropic structures and turbulent kinetic energies on the streamwise direction were looked into and compared with three jets, The results show that mean velocities have represented potential core and decayed with similar gradients. The turbulent intensities and shear stresses were presented peak values in the self-preserving region, and then they were in decay. Aeolotropy in the initial region were possible returned to isotropy patterns with asymptotic approach in the downstream region. It has been found that the turbulent kinetic energies for the three cases of jet existed in the similarity and they coincided with Gaussian profile.

The characteristics of heat transfer and pressure drop through tubes has been investigated experimentally for a compound heat transfer enhancement. The test tubes were spirally indented tubes with wire coil inserts which had a various combinations of pitch and helix angles. Pure water was used as working fluids for the experiments, Heat transfer coefficients and friction factors of the test tubes were evaluated from the values of measured temperatures, flow rates and pressure drops. An performance evaluation was performed to find an optimal combination of spirally indented tubes with wire coil inserts. When the helix angle of wire coil insert are $71^{\circ}-72^{\circ}$, the best heat transfer enhancement was shown. The friction factor was 9 - 13 times higher than those in smooth tubes, and the heat transfer was enhanced a maximum of 500%.

A criterion for evaluation of burners has changed recently, and the environmental problems are raised as a global issue. Burners with higher thermal efficiency and lower oxygen in the exhaust gas, evaluated better. To comply with environmental regulations, burners must satisfy the $NO_x$ and CO regulation. Consequently. 'good burner' means one whose thermal efficiency is high under the constraint of $NO_x$ and CO consistency. To make existing burner satisfy recent criterion, it is highly recommended to develop a feedback control scheme whose output is the consistency of $NO_x$ and CO. This paper describes the development of a real time flame diagnosis technique that evaluate and diagnose the combustion states, such as consistency of components in exhaust gas, stability of flame in the quantitative sense. In this paper, it was proposed on the flame diagnosis technique of burner using Neuro- Fuzzy algorithm. This study focuses on the relation of the color of the flame and the state of combustion. Neuro- Fuzzy learning algorithm is used in obtaining the fuzzy membership function and rules. Using the constructed inference algorithm, the amount of $NO_x$ and CO of the combustion gas was successfully inferred.

The change of crystalline structure and mechanical properties of drawn PP filaments which was treated by tensioned and non-tensioned annealing was investigated. Measurements were carried out with XRD for crystallite size, density gradient tube for crystallinity. and UTM for mechanical properties. Tensioend and non-tensioned annealing were carried out $80^{\circ}C$, $100^{\circ}C$, $120^{\circ}C$: for 10min., 30min., 60min, in oil bath. It was found that the crystallinity and crystallite size of (110) plane of samples were increased with increasing of annealed temperature and time. Also crystallinity and crystallite size of samples which was tensioned annealing were larger than those of non-tensioned annealed samples. Initial modulus and tensile strength of tensioned annealed samples were higher than non-tensioned annealed samples, But elongation of tensioned annealed samples was lower than non-tensioned annealed samples.

Concrete mix proportioning is a process of selecting the right combination of many materials such as cement, fine aggregates, coarse aggregates, water, and admixtures to make concrete satisfying for specification and cost. In determining proportioning of concrete mixes, code information, specification, and the experience of experts are needed. However, all factors regarding mix proportioning factor cannot be considered. Therefore, the final acceptance depends on concrete quality control test results. The proportioning of concrete mixes and the adjustments are somewhat complicated, time-consuming, and uncertain tasks. In this paper, as a tool to predict the factor of the proportioning of concrete mixes, an artificial neural network is used. To consider the varieties of material properties, the standard mixed table of two companies of ready mixed concrete are used. The results show that neural net works is successfully applied to the prediction of concrete mix proportioning factor.

The purpose of study is to examine the sensitivity of the rate of degradation to initial TCE concentration and iron concentration in the solution. The batch tests were executed to assess the degradation rate at varying initial conditions. First order rate constants($k_a$) were more rapid with the lower initial TCE concentration, Howere the correleation was not always linear between $k_a$ and initial TCE concentration. $k_a$ was proportionally increased as the increasing surface area. It implied that the effective reactive surface area acted as the limiting factor on the reductive dechlorination of TCE by iron.

A large floating structure is attracting great attention in recent years from the view of ocean space utilization. Its huge scale in the horizontal directions compared with the wavelength and relatively shallow depth make this type of floating structure flexible and its wave-induced motion be characterized by the elastic deformation. In this paper, a boundary integral equation method is proposed to predict the wave-induced dynamic response mat-like floating offshore structure. The structure is modeled as an clastic plate and its elastic deformation is expressed as a superposition of free-vibration modes in air. This makes it straightforward to expand the well-established boundary integral technique for rigid floating bodies to include the hydroelastic effects. In order to validate the theoretical analysis, we compare with the experimental result of previous model test. Satisfactory agreement is found between theory and experiment.

This dissertation deal with over-all wireless communication technology. And introduce wireless communication technology analytically that it use for Home-LAN communication technology (HomeRF, Bluetooth, IEEE 802.11, HIPERLAN, etc). Home-LAN communications issue by the terminal field of the latest high-speed network construction. This technologies possesses characteristics and significances as the representative technology using in Home-LAN communication technology. Also, the method of application is conditional on individually. Wireless LAN put Home-LAN communications to practical use. Bluetooth have practical use for an individual mobile communications with internet. HomeRF have a vision that the construction of wireless system in house purely. Therefore, this dissertation investigates merits and demerits between those technologies. And then leads the most compatible technology for application of Home-LAN. Finally, this thesis have a view of the development course hereafter.

The epitaxial growth of Ge on the clean and surfactant(Sn) adsorbed surface of Ge(111) was studied by the intensity oscillation of a RHEED specular spot. In the case of epitaxial growth without the adsorbed surfactant, the RHEED intensity oscillation was stable and periodic up to 24ML at the substrate temperature of $200^{\circ}C$. Therefore the optimum temperature for the epitaxial growth of Ge on clean Ge(111) seems to be $200^{\circ}C$. However, in the case of epitaxial growth with the adsorbed surfactant, the irregular oscillations are observed in the early stage of the growth. The RHEED intensity oscillation was very stable and periodic up to 38ML, and the $d2{\times}2$ structure was not charged with continued adsorption of Ge at the substrate temperature of $200^{\circ}C$. These results may be explained by the fact that the diffusion length of Ge atoms is increased by decreasing the activation energy of the Ge surface diffusion, resulted by segregation of Sn toward the growing surface. From the desorption process, the desorption energy of Sn in Ge $\sqrt{5}{\times}\sqrt{5}$ structure is observed to be 3.28eV.