The voice over IP(VoIP) technology is currently recognized as the base technology for the next generation telecommunication services. So the VoIP market has been extremely expanding with the opportunity for cheap phone calls. This paper describes the packet voice testing issues and scenarios for the VoIP services. These issues and scenarios are deduced from the testing results through KT VoIP testbed composed of commercial systems.

Today, QoS is one of the most critical issues in the network research area and Differentiated Services (DiffServ) is considered as the most prominent solution to provide some kinds of service differentiation without introducing any scalability problem. Among DiffServ's approaches, Assured Service (AS) provides some minimal level of QoS guarantee by treating more preferably than traditional Best Effort (BE) traffic and by using different level of drop probabilities within the same AS classes. In this paper, we investigate the ECN's capability of improving overall goodput of the flows and the possibility of resolving the fairness problem among the flows belonging to same class in Differentiated Services architecture.

Recently, with the advent of satellite communication technologies, the network access service through satellites has emerged as an alternative to existing ones. Of satellite access services including multimedia services, the high speed internet access service will be one of the important services. Particularly, the efficient transportation of real time internet traffic seems very essential. The aim of this research is to examine the applicability of the IETF RTP protocol in the satellite access network. The RTP has been developed for the QoS-met transportation protocol of real time traffic over the existing best-effort internet. This paper summarizes the RTP protocol, and describes the architecture of the implementation of the RTP. And also, the compressed RTP header protocol is discussed for the applicability to the satellite link.

TCP is ill-suited to real-time multimedia applications. Its bursty transmission, and abrupt and frequent wide rate fluctuations cause high delay jitters and sudden quality degradation of multimedia applications. Deploying non congestion controlled traffic results in extreme unfairness towards competing TCP traffic. Therefore, they need to be enhanced with congestion control schemes that not only am at reducing loss ratios and improve bandwidth utilization but also are fair towards competing TCP connections. This paper proposes a differentiated rate adaptation algorithm based on loss and round trip time. Rate in a sender quickly responds to loss ratio and holds steady state. Additionally, this algorithm reduces loss ratio by loss prediction in a receiver.

End-to-end congestion control mechanism have been critical to the robustness and stability of the Internet. Most of today's Internet traffic is TCP, and we expect this to remain so in the future. TCP/IP is the intermediate transport layer candidate for today's applications. TCP uses an adaptive window-based flow control. The congestion avoidance and control algorithms deployed by TCP aims at using the available network bandwidth. This paper compares different congestion control policies, and proposes the new design mechanism for future public networks

As Internet users and network traffics are explosively increased, many researches have been done to provide fast and guaranteed Internet services. The results of these efforts are Multiprotocol Lab el Switching(MPLS) and differentiated service(Diff serv) emerging as a next generation backbone net work. In this paper, we make a research on gearing (or interworking) two technology needed to support end-to-end QoS and explain sequential procedure. And we simulate the L-LSP/E-LSP proposed by Working Group of IETF to be deployed to the DiffServ module which is implemented based on the MPLS network simulator and analyze the performance of the simulation result.

MPLS stands for “Multi-protocol Label Switching”. It's a layer 3 switching technology aimed at greatly improving the packet forwarding performance of the backbone routers in the Internet or other large networks. We compare the performance of unlabeled IP traffic and labeled IP traffic. In this paper, by varying the packet rate and measuring throughput of the flows we analyze the performance of labeled IP packet traffic and unlabeled IP packet traffic in IP over MPLS.

Multi-protocol Label Switching is a comparatively new technology based on the association of labels with routes and the use of labels to forward packets. MPLS can be used for transport of any level 3 protocol over any level 2 technology. Differentiated Services define a model for implementing scalable differentiation of QoS in the Internet. The inherent characteristics of MPLS make it a very good candidate for providing Differentiated Services. In this paper we describe various approaches which can be used to support differentiated services in MPLS environments.

Multi Protocol Label Switching (MPLS) is a high performance method for forwarding packets (frames) through a network. It enables routers at the edge of a network to apply simple labels to packets (frames). we use MPLS in the core network for internet. MPLS provide high speed switching and traffic engineering in MPLS domain but at the Label Edge Router(LER) there is frequently cell discarding via congestion and buffer management method. It is one of the most important reasons retransmission and congestion. In this paper we propose advanced LER scheme that provide less cell loss rate also efficient network infrastructure.

Because of internet's growth, today's network has a serious bandwidth problem. WDM(Wavelength Division Multiplexing) is a solution of this problem. In the WDM networks, QoS(Quality of Service) is as important as bandwidth. And today's voice over IP technology makes a lot of delay-sensitive internet traffic. De]ay-sensitive internet traffic is growing up, so more QoS is needed. We proposed effective solution to assign QoS.

In this paper, we designed bluetooth module using 2.4 GHz ISM band. Bluetooth is wireless networking solution that connects PDA, cellular phone, printer, PC, etc each other. We integrated digital and RF part in one module. As a result, we can make low power consumption module that enables long battery life. In addition, we enlarged maximum available range of our module from 10m to l00m. This module satisfies bluetooth specification 1.0.

본 논문에서는 전력선 기반의 홈네트워크에 연결된 장치들을 원격에서 PDA나 웹을 통해 모니터링하고 제어할 수 있는 홈게이트웨이 프로그램을 제안한다. CEBus 장치와 Low rate의 전력선 모뎀을 지원하며 서버 프로그램은 C++로 짜여져 있다. 웹브라우저를 통해 홈네트워크에 액세스할 경우, 자바 애플릿의 UI 프로그램이 클라이언트에 다운로드 되어 이를 통해, 홈네트워크를 장치를 제어한다.

In this paper, the architecture for the residential gateway is designed for the traffic statistics of home environment. The suitability of 10 Mbps power line communication is investigated for the control and the video data distribution through simulation. The design issues are discussed for a residential gateway and the network design that is based on the power line communication is presented. Traffic models are established from the actual traffic traces. They are used for performance evaluation of residential networks.

본 논문은 블루투스 헤드셋의 구현에 대해 기술한다. 블루투스 헤드셋은 ACL 연결을 통하여 헤드셋과 오디오 게이트웨이 사이의 link를 선정하고, SCO 연결을 통하여 64kbps의 음성을 전송한다. 본 논문에서 구현한 블루투스 헤드셋은 HCI가 없는 구조로 설계되어 블루투스 모듈내에 모든 프로토콜 스택이 구현되었고, 헤드셋에 구현된 상위 프로토콜 및 응용 프로그램에 대해서 Unix 환경에서 C-language modeling을 통하여 검증하였다.

There are many methods of generating PN sequences. In this paper, we propose and examine a new class of composite shift register to generate PN sequences. The new composite generator, in comparison with the original LFSR which generates PN codes of period 2$^n$-1, when coupled with codes of period k, generates PN codes with (longer) period LCM(2$^n$-1,k).

In CDMA, the currently used PN code acquisition methods detect the phase of the incoming PN signal on the basis of ML estimation. In serial search strategy, it takes relatively long time for PN code acquisition. A study related to reduce processing time of PN code acquisition is important. Therefore we propose a reference code design for a new algorithm that a reference code and the received PN code are fully correlated to detect the transmitted PN code, in detail, the relative phase offset j of c⒡. After choosing two weight factors, we show the mathematical analysis and derivation for the reference code design.

In CDMA systems, the performance of the typical multipath searcher degrades much according as the signal to noise ratio becomes low. In this paper, multipath searcher algorithm is proposed based on sliding window to overcome this drawback. In searcher systems, correlation values between incoming and local PN sequences are used to acquire multipath components. Therefore more accurate distributions of correlation values obtained through this proposed algorithm enables to get higher detection probability. In computer simulations, it is verified that proposed algorithm has better performances in Rayleigh fading channel and Gaussian channel.

We investigate the stepwise parallel processing of the serial search which can success the co]1 search at low Ec/Io. The single path Rayleigh fading channel which is worst-case channel model is considered. The typical 3-step cell search is used. The probabilities of detection, miss and false alarm for each step are used in closed forms based on the statistics of CDMA noncoherent demodulator output. The optimal power allocation to each channel and The optimal number of post-detection integrations for each step is obtained. Also, the cumulative probability distribution of the average eel] search time for serial search methods are compared.

Adaptive filter based code acquisition scheme offers a fast acquisition with a low error probability. However, it has been studied only under a coherent environment. In this paper, the noncoherent adaptive code acquisition scheme employing a differential detection technique is proposed. For the proposed scheme, system probabilities and the mean acquisition time are analyzed numerically. Simulation results show that the proposed system outperforms over the conventional matched filter by 2-4 ㏈ under AWGN channel for 16 taps.

This paper has been studied the design of 16-QAM demodulator used in broadband wireless local loop subscriber station. In B-WLL systems, transmission signal experience the inter symbol interference(ISI) due to multipath, frequency offset of RF/IF local oscillator and phase offset. In this paper, we discuss the effective data recovery algorithm for 16-QAM demodulator to compensate the distorted signal from ISI, frequency offset and phase offset.

In order to resolve problems according to the phase error in QPSK demodulator of the digital communication systems. The demodulator requires carrier recovery loop which searches for the frequency and phase of the carrier. In this paper the complexity of implementation is reduced by the reduction into half of the number of the multiplier in filter structure of the conventional carrier recovery loop, and as the drawback of NCO of the conventional carrier recovery loop wastes a amount of power for the structure of lookup table , We designed the structure of combinational logic without the lookup table. In the comparison with dynamic power of the proposed NCO, the power of NCO with the lookup table is 175㎼, NCO with the proposed structure is 24.65㎼. As the result, it is recognized that about one eight of loss power is reduced. In the simulation of carrier recovery loop designed QPSK demodulator, it is known that the carrier phase is compensated.

This paper has been studied the detail design, implementation and test of an IFU for the B-WLL. At the first, In/out reference of the IFU is established based on the Air Interface ODU(Out Door Unit) standard for B-WLL of TTA and the Technical conditions of the MIC. The implemented IFU is tested with CMTS/CM system, And the test system(CMTS/CM) with the B-WLL IFU is operated properly and the characteristics of the IFU satisfies the requirements of the B-WLL IFU.

This paper has been proposed an audio DAC structure composed of FIRs and IIR filters as digital interpolation filter to integrate the off-chip analog low-pass filter on-a-chip. The passband ripple(< 0.41${\times}$fs), passband attenuation(at 0.41${\times}$fs) and stopband attenuation(> 0.59${\times}$fs) of the Δ$\Sigma$ modulator output using the proposed digital interpolation filter had ${\pm}$ 0.001 ［㏈］, -0.0025［㏈］ and -75［㏈］, respectively. Also the inband group delay was 30.07/fs［s］ and the error of group delay was 0.1672%. Also, the attenuation of stopband has been increased -20［㏈］ approximately at 65［㎑］, out-of-band. Therefore the RC products of analog low-pass filter on chip have been decreased compared with the conventional digital interpolation filter structure.

IMT-2000 지상 시스템에서는 순방향 링크의 용량을 증대하기 위하여 다중 전송 안테나를 이용하는 다양한 전송 다이버시티 기법들이 연구되고 있으며, 3GPP를 위한 표준 가운데 하나인 폐쇄루프 전송 다이버시티 기법은 단말기에서 순방향 채널의 상태에 따라 전송 안테나의 가중치를 결정하여 궤환함으로써 여타의 기법에 비해 우수한 성능을 보인다. 하지만 지상 시스템과는 달리 IMT-2000 위성 시스템에서는 현재 전송 다이버시티에 대한 표준이 없는 상황이며 이에 대한 연구 역시 미진하다. 본 논문에서는 폐쇄루프 전송 다이버시티를 IMT-2000 위성 시스템에 적용한 결과를 제시한다. IMT-2000 위성 채널 모델에 대한 모의 실험 결과 2개 안테나를 이용하는 폐쇄루프 전송 다이버시티를 통해 단일 안테나 혹은 2개 안테나 전송 신호의 단순한 다이버시티 결합에 비해 월등한 성능 향상이 가능함을 확인하였다.

In this paper, we analyze the propagation modeling methods to evaluate the IMT-2000 satellite RTT (Radio Transmission Technology). To generate Rayleigh random numbers having Jake's Doppler power density spectrum, the Rice's sum of sinusoids methods are used and their statistical characteristics are compared with each other.

무선채널환경에서의 하향 방향 링크 상에서 페이딩 효과에 효과적으로 대처하고 고품질의 수신신호를 위하여 시간, 주파수 및 공간 영역 상에서의 여러 형태의 독립적인 다이버시티를 임의로 발생하기 위한 방안이 연구 되어왔다. 특히 3GPP 지상시스템에서 사용되는 개방형 전송 다이버시티 기법중 하나인 STTD( Space-Time Transmit Diversity)는 시공간 블록코드를 기반으로 하고 있으며, 본 논문에서는 이를 IMT-2000용 위성시스템의 순방향링크에 적용하여 이에 대한 결과를 고찰한다. 위성시스템의 순방향채널은 위성의 앙각에 의하여 라이시안 팩터 성분이 결정되며, 다수의 가시 위성군을 통하여 다이버시티효과를 발생시킴으로써 성능을 향상시킬 수 있다. 본 논문에서는 현재까지 상세한 규격작업이 이루어지고 있지 않은 IMT-2000용 위성시스템 상에서 두개의 가시위성을 통한 STTD 적용시 우수한 수신성능을 확인하였다.

The satellite communications are expected to play an important role to provide broadband multimedia services in the 21st century. According to this requirements, this paper describes the design and implementation of ATM-based high speed satellite modem ASIC chipset. The ASIC chip consists of three main parts, CODEC, Modulator and Demodulator. It supports burst and continuous mode operation with TDMA frame consisted of Reference bursts, Inbound burst, and Traffic burst. The maximum transmission rate is OC-3 (155Mbps) and the maximum operating clock speed is 220MHz. This ASIC chip was implemented with 0.25um CMOS technology.

The effect due to group delay and non linear characteristics in high speed data satellite channel was represented in this paper. Based on the modeling of group delay and non linear characteristics the performance was analyzed in ka band satellite channel. The group delay and non-linear characteristics in high speed data transmission severely affect the system performance. The more Eb/No is required to satisfy the required system performance. The optimum operating points of HDR satellite transmission system are implemented by considering analyzed results for channel characteristics

This paper discusses solutions for forward link power allocation based on 3GPP(FDD) standardization reports and which meet the required Eb/No of forward link channels. In addition, the forward link user capacity in a mixed service environment. Cell coverage is induced from the user capacity solutions using the urban propagation model. In an urban macrocell environment, the forward link user capacity turns out to be roughly 29 and 3, respectively, for voice and data service (144 kbps) at a distance of 1 km, and in an urban microcell environment, the user capacity turns out to be Toughly 14, 4, and 2, respectively, for voice and two data services (144 kbps, 384 kbps) when the cell radius is 0.2 km.

In IMT-2000 systems, the outer loop dynamically adjusts the target SIR so that adequate performance in terms of the frame error rate(FER) and the true quality measure is achieved. This paper utilizes an analytic model lot outer loop power control(OLPC) adjusting the target SIR in IMT-2000. The analytic model is based on the discrete-time Markov chain as voice traffic SIR. It is described that the model can be used to find the optimum step size in voice traffic for fast fading environments. The optimum step size influences the performance of OLPC： As the step size decreases, the average target SIR increases and average FER decreases.

In this paper, the handoff margins are analyzed using the propagation attenuation which is modeled as a product of the fourth power of the distant and a log-normal random variable whose standard deviation is 8 ㏈. The effect of handoff techniques on cell coverage for CDMA system are shown that soft handoff increases cell coverage relative to hard handoff. When the cell radius extends 5-10 % and the outage probability is 10 %, the relative cell coverage area is extended 3.22 ㏈-3.99 ㏈ and 2.55 ㏈-2.85 ㏈ with power control and without power control, respectively.

This paper describes how to Implement dual band GSM hand set varying single band GSM phone. The idea can be extended to Triple mode design. Multiband design is important for global roamming and Baseband setup planning. Here H/W and SW issues are briefly described

Generally in the case of mobil communication service for long distance sea, unlike heavily populated residential areas, providers need to minimize the service area per base station. Therefore, in this thesis, the 800 ㎒ CDMA system should be extended to give better long distance communication service. This model is used to predict the occurring receiving power of the mobile stations that we simulated and analyzed. As a result, the experiment demonstrated the appropriateness of predicting receiving power using this model.

In this paper. we analyzed the performance of a SFH (slow frequency hopping) system under partial-band jamming, multiple access interference and wide-band random noise. For the correction of burst errors due to channel hit, Reed-Solomon coding followed by block interleaving is employed. Errors-and-erasures decoding with side information is exploited to enhance the correctional capability. We derived a closed-form solution for the BER estimation. Errors resulting from random noise and erasures resulting from burst interference are separately analyzed and finally BER is computed due to these composite noise sources. Estimated BER performance is verified by computer simulation.

PRML (partial response maximum-likelihood) 과 FDTS/DF (fixed-delay tree search with decision feedback)는 기록 저장 시스템에서 준최적의 성능을 보임이 잘 알려져 있다. 그러나, 위와 같은 정보열 검출 기법은 피할 수 없는 복잡도 문제를 가지고 있다. 본 논문은 최소 run 길이 제한조건 d=2를 가진 광기록 채널을 위한 다양한 저복잡도 검출 기법을 다룬다. 우선, 결정 궤환 기법을 이용한 이산 정합 여파기 (discrete matched filter with decision feedback：DMF/DF)가 기존의 PRML로부터 유도된다. 유도된 시스템은 PRML보다 결정 궤환에 의한 성능 이득을 갖는다. 또한, 메트릭 계산을 사용하지 않는 저복잡도 FDTS/DF가 유도된다. 모의실험 결과에 의하면, 유도된 저복잡도 검출 기법들은 기록 밀도 S>=5.5에서 P(D)=1+D+D/sup 2/+D/sup 3/의 target을 갖는 PRML보다 우수한 성능을 보인다.

This paper presents the performance of a GHICW(Group-wise Hybrid Interference Cancellation scheme based on Wiener filtering) receiver for the multi-rate DS-CDMA system. Our scheme has a small processing delay and a simple hardware complexity compared to ordinary interference cancellation schemes by grouping users with the same date rate. The performance improvement of the low rate user is obtained by using a Wiener filter which precisely estimates the high rate users' bit.

In this paper, the reverse link performance of an imperfect power controlled DS/CDMA cellular system that uses a base station array antenna which can effectively remove the multiple access interference is analyzed considering both beam forming algorithm and power control error in shadowing. The blocking probability of the DS/CDMA cellular system based on array parameters, Eb/No and statistics of interference is derived, and then the system capacity corresponding to a certain blocking probability is calculated. On the assumption that the blocking probability is set 1 ％, the system capacity using MCGM algorithm with 12 antenna arrays is increased about 59 % than that using 8 antenna arrays when power control error is 2.5 ㏈.

In this paper, the performance of the parallel interference cancellation(PIC) with RAKE receiver is more precisely analyzed in the uplink multipath fading channel. There is some difference between the proposed analysis method and the previous ones. Namely, it can be confirmed that the proposed analysis method by using stochastical characteristics is more accurate than the previous ones. It is also verified that the analysis result is similar to simulation as the number of user is increased. It is assumed that the channel estimation is perfect and the delay of multipath is Tc in the simulation.

In order to design a low complexity and high performance SOVA decoder for Turbo Codes, we need to analyze the decoding performance with respect to several important design parameters and find out optimal values for them. Thus, we use a scaling factor of soft output and a update depth as the parameters and analyze their effect on the BER performance of the SOVA decoder. finally, we shows the optimal values of them for maximum decoding performance of SOVA decoder for 3GPP complied Turbo codes.

Given the frame size and constituent encoders, interleaver plays a central role in a turbo code performance. Interleaver should be designed to generate a heavy weight codeword in the second encoder if the first encoder generates a low weight codeword. In this paper we present a search procedure for high performace interleaver whose performance is measured by computing union bound using the weight spectrum of all the weight 2, 3

The bit error rate(BER)of the data passed through Wideband-Code Division Multiple Access (W-CDMA) system with turbo-codes structure is presented. The performance of turbo-codes under W-CDMA system is estimated for various users and iteration numbers of decoding. The channel model is Additive White Gaussian Noise(AWGN) and Rayleigh fading channel. When iteration number increases, bit error probability of turbo-codes decreases. and when the number of users increase, bit error probability of turbo-codes increases.

본 논문에서는 다중 경로상의 DS-CDMA 시스템을 위해 우리가 이미 제안한 Rake 수신기와 다이버시티 결합 구조를 이용하는 CMA 기반의 적응 간섭 제거 기법에서 실제 채널 추정 기법을 사용할 때 부정확한 채널추정이 성능에 미치는 영향을 검증하였으며, sliding widow averaging 형태의 단순한 채널 추정 기법을 이용할 경우 slow 페이딩 및 fast 페이딩 환경에서의 모의실험 결과 이상적인 채널 추정을 가정한 경우와 유사한 우수한 성능을 보임을 확인하였다.

The fact that the channel coding methode with property of the source coder is better than using the channel characteristics is well known. In this paper We propose the UEP channel coding scheme using IP-SCCC and DCT-based embedded coder for image transmission. Moreover, to evaluate the effectiveness of the proposed scheme some simulation results are presented, in which the channel models of additive white Gaussian noise and Rayleigh fading are assumed.

Optical burst switching(OBS) is a new switching paradigm to supporting bursty traffic on the Internet efficiently. OBS separates burst level and control level. To handle data burst efficiently, the scheduling schemes in optical burst switching systems must keep track of future resource availability when assigning arriving data bursts to wavelength channels. In this paper, we evaluate the performance of three scheduling schemes which are called Horizon, Single-gap and Multiple-gap, as a basic study for the future research of Optical Internet. Thus, firstly, we analyze the trade-off between the performance and the processing overhead of each scheme. In addition, the performance of OBS system which uses Multiple-gap scheduling is evaluated in detail under various network size. We use simulation for performance evaluation in terms of burst loss rate(BLR), wavelength channel utilization and the number of management data.

In this paper, the design of WDM network using the traffic estimation modeling is implemented. Because of the lack of data of real traffic volumes, the information of statistic data is used. using the modeling results, the WDM channels is assigned for each node, and the network is simulated using OPNET simulation tools. As a result, the realistic WDM network design for Korea topology is proposed.

A signal transport scheme to the maintenance signals for the WDM optical transmission system and the supervisory channels to the signal transport is presented, and the novel supervisory channel scheme fur the future optical transport network (OTN) are discussed.

This paper proposes a fuzzy-based random access controller with a superimposed frame structure (F$^2$RAC) fur voice/data-integrated wireless networks. F$^2$RAC adopts mini-slot technique for reducing contention cost, and these mini-slots of which number may dynamically vary from one frame to the next as a function of the traffic load are further partitioned into two regions for access requests coming from voice and data traffic with their respective QoS requirements. And F$^2$RAC is designed to properly determine the access regions and permission probabilities for enhancing the data packet delay while ensuring the voice packet dropping probability constraint. It mainly consists of the estimator with Pseudo-Bayesian algorithm and fuzzy logic controller with Sugeno-type of fuzzy rules. Simulation results prove that F$^2$RAC can guarantee QoS requirement of voice and provide the highest throughput efficiency and the smallest data packet delay amongst the different alternatives including PRMA［1］, IPRMA［2］, and SIR［3］.

A new medium access control protocol is proposed to support stable wireless Internet services. Using the characteristics of the uplink Internet traffic and a Voice-Packet multi-session mode, the proposed protocol transmits the uplink Internet traffic via the voice traffic channel of silent duration in a multi-session mode. Out simulation results show that the proposed protocol guarantees stable wireless Internet services under heavy loads.

In this paper, The RF system of W-CDMA receiver is designed and the performance is analyzed. The linearity characteristic and the noise characteristic are presented in the performance. The linearity characteristic is analyzed by PN and IIP3. The noise characteristic is analyzed by NF. In addition, sweeping of the nonlinear components parameter affecting the linear performance is tested and the most maximal possible parameter to maintain the linear performance is introduced. The transceiver RF system of W-CDMA and cdma2000 is designed and presented adapting the nonlinear parameter introduced.

In this paper, a wireless engineering field tool based on WCDMA is designed and implemented. Emerging requirements for higher rate data service and better spectrum efficiency are identified for the third generation mobile radio systems. The proposed WCDMA field tool is used for improving the quality of WCDMA service. The current position and time are measured and recorded with CDMA field data. With the system a user can observe the spatial distribution of the field data. For providing concurrency, the system is decomposed of four units and each unit is implemented by using threads.

In this paper, we have designed a pager based on the FLEX protocol. The pager consists of a decoder, a MCU, a SPI, and a User interface. The decoder contains the following blocks： synchronizer, de-interleaver, error corrector, packet builder. The decoded data is converted to SPI packets for communication between the MCU and the FLEX decoder. The host MCU is a RISC pipelined architecture, so it processes data at high speed and also sends messages to user interface. We have designed the proposed pager as structural modeling using VHDL language. Then, We simulated and synthesized it using tool of SYNOPSYS corporation.

This paper discusses performance evaluation methodologies for wired/wireless Ethernet adaptors. This paper defines test cases for performance evaluation of LAN adaptor and its environments. Performance evaluation of LAN adaptor is mote complex as compared with interconnection devices such as Ethernet HUB and Ethernet switch, because its performance depends on the system on which the adaptor is plugged. Such dependencies include CUP type, RAM size, system bus architecture(PCI bus clock), etc.

In this paper, we propose a new scheme which improves the IP address lookup time. The new scheme is composed of two core technologies, named the prefix alignment and the prefix distance ordering. Now, as the Internet is being used commonly by improving the data transmission capacity, the need for enlarging the bandwidth of the Internet is on the rise. IP address lookup performance problem is an important obstacle in the router executing high speed packet forwarding. This results from the fact that the prefixes routing table is composed of and the traffic being processed in unit time are largely on the increase. The proposed lookup scheme is divided into two parts in technology, the one is the algorithm forming a routing database(routing table), the other is the lookup procedure in the actual packet processing.

This paper studies a real-time VBR traffic characterization. There are two big approaches to determine traffic. One is a statistic approach and the other is a deterministic approach. This paper proposes a new constraint function, what we called “Sub-Sum Constraint Function”(SSCF). This function is mainly based on a deterministic approach and uses a statistic approach. It predicts and calculates the next rate with a present information about the stream. SSCF captures the intuitive bounded by a rate lower than its peak rate and closer to its long-term average rate. This model makes a order of the constraint function much less than any other works (O(n)). It can also be mapped on a token bucket algorithm which consists of r (token rate) and b (token depth). We use a concept, EB(effective bandwidth) for a utility of our function and comparing with other techniques such as CBR, average VBR. We simulated 21 multimedia sources for verifying the utility of our function.

The issue of supporting TCP traffic over ATM networks is currently one of the most important issues in the field of data networks. One important part of this issue is congestion control. In general, congestion control uses method such as packet drop to relieve network resource when the network is congested so as to maintain high throughput and low delay. In addition, congestion control is required to ensure fair sharing of resources among all users during congestion. In this paper we propose a new congestion control method using WRED & per-VC accounting mechanism. This packet discard scheme is proposed with the goal to provide both good performance in terms of throughput and fairness in terms of bandwidth exploitation of the output link among all virtual circuits.

In this paper, we present the design of AAL2/AAL5 Type conversion Unit using among BSC, BTS, Core-Network in IMT-2000 system. We first briefly introduce the B-ISDN ATM Adaptation layer specification of Type 2 AAL and Type 5 AAL, and describe conversion flow and each module. And then this paper has designed AAL2/AAL5 Type Conversion Unit and simulated it.

AAL2는 ATM 망에서 Low bit Rate의 음성이나 데이터를 Real-Time으로 전송하기 위해 만들어진 표준안이다. IMT-2000 System에서는 ATM을 근간으로 시스템이 구성되며, 이동전화 가입자의 음성패킷이나 Low bit rate 데이터를 전송하기 위해 AAL2를 채택하였다. 본 논문에서는 IMT-2000 System에서 AAL2를 구현하기 위한 시스템의 구조와 실제AAL2를 구현한 예를 보인다.

본 논문에서는 다중 경로 페이딩에 의한 성능의 손실을 보상하기 위하여 간단한 equal gain combining diversity를 갖는 802.11a 무선 LAN용 OFDM 시스템의 HER 성능을 다중경로 환경 하에서 분석하였다. 모의 실험 결과에 따르면, 다중경로채널에서 전송 파워를 살펴보면, 2branch equal gain combining diversity를 사용한 무선 LAN용 OFDM시스템이 diversity를 사용하지 않는 OFDM 시스템보다 BER 10/sup -3/에서 3㏈ 정도의 이득을 줄 수 있었다. Branch 수를 3개를 사용한 경우에는 BER 10/sup -3/에서 branch 2개를 사용한 경우보다 약 2㏈정도 이득을 줄 수 있었다.

In this paper, we design the system that support data rate of 6Mbps(BPSK), 12Mbps(QPSK), 24Mbps(16-QAM) with OFDM, and the performance of this system analyze in the indoor channel when BER is 10$\^$-3/. In this simulation, first, we analyze performance of the system with and without channel coding. As the result, the coding gain of each system is 2㏈, 1.6㏈, 2㏈ when BER is 10$\^$-3/ Second, In the case of 16-QAM/OFDM, The effect of soft decision channel decoding method improve 2㏈ than hard decision when BER is 10$\^$-3/.

In this paper, we investigate performance of OFDM employing macrodiversity selection on a shadowed multipath channel to reduce the effects of long-term shadowing. Three different situations are considered： independent shadowing with equidistant ports, independent shadowing with non-equidistant ports, and correlated shadowing. Numerical results show that OFDM performance is improved as the number of macrodiversity ports increases. In the situation where the user is much closer to certain port(s), performance becomes worse compared to that of the equidistant situation. In addition, as the correlation increases among the ports, the advantage of macrodiversity is reduced.

In this paper, we present the performance of a multi-code parallel combinatory CDMA system using bi-orthogonal modulation under multipath fading channel. In general, the dynamic range of the amplitude of the transmit signal is very large in conventional multi-code CDMA systems, resulting in severe nonlinear distortion due to high power amplifier and thus significant BER performance degradation. Since the number of simultaneously multiplexed code channels in the proposed system is reduced, the proposed system exhibits reduction of peak-to-average power ratio (PAPR) of the transmit signal amplitude with significant BER improvement. We verify the performance of the proposed system by computer simulations under the Vehicular B multipath fading channel model by ARIB.

In this paper, the performance of a MC-CDMA system applying adaptive subchannel allocation scheme and M-ary orthogonal signaling is analyzed for forward links in Rayleigh fading channel. In the proposed system, each DS waveform is transmitted over the subchannel having the biggest fading among L subchannels. Assuming M-ary orthogonal signaling and 4 subchannels, the BER of 10$\^$-3/ is satisfied if SNRs are 7.33 ㏈, 5.33 ㏈, and 4.47 ㏈ for k=1, 2, and 3, respectively. Also, SNRs which met BER of 10$\^$-3/ are 1.42 ㏈ and 2.33 ㏈ in L=2 and L=8 as k=1 is increased to k=2. It is shown that the MC-CDMA system has performance improvement as a number of subcarriers and M-ary orthogonal signaling.

This paper presents an Interprocessor Communication Network(IPC net) in ATM switching system. In order to supply stable and independent path for processor communication, additional network i.e., Ethernet, is suggested. An Ethernet switch centered on Ethernet binds each processor into a work range. IPC net proposed in this paper assures end-to-end inter-processor connection, uniform 100Mbps Ethernet bandwidth and enhanced user cell throughput of ATM switch with minimum Ethernet supporting block integrated into ATM system

MSF(MultiService Switching Forum) 개념이 도입된 개방형 시스템 구조를 적용한 고성능 스위칭 시스템 개발이 필요하며, Media Gateway System은 ATM망에서 중저속의 Non-ATM 인터페이스를 수용하는 ATM access multiplexer/concentrator로서 ATM 물리계층 기능, ATM 계층 기능, 회선대행 기능, AAL2 trunking 기능, N-ISDN 연동 기능 및 FR/ATM 연동기능을 제공한다. 본 논문에서는 Media Gateway System에 FR/ATM 연동 기능을 구현하기 위하여 적용할 연동 규격을 살펴보고 FR/ATM 연동시스템 구조를 제안하였다.

In this paper we develop a dual storage device to store a lot of data safely and reliably in communication system. The device consists of micro-controller, FPGA and hard disk. It provides many functions those are rebuilding, automatic remapping, host service and remote host service. The developed device can be used instead of expensive storage device like flash memory in various communication systems.

In this paper, we consider the simple redundant structures with the function of hardware based active/standby control. The system includes two switch modules. The switch module is connected to a data bus, but only the active switch module has control of the data bus. The standby unit takes over the function of the active unit when the active unit failure or mode command are asserted. And this paper illustrate the high-speed router system and the overall redundant system architecture. The proposed redundant architecture for 80G Router system is verified and implemented with experiment.

This paper reports a very fast lookup scheme for Optical IP racket forwarding. A LD by derived Pattern Generartor generate a optical IP Packet encapsulated by any header of level1 and level2. A high speed Lookup scheme for a forwarding has been implemented by EEPLD with tiny SRAMs for optical internetworking. With SRAM of a 10㎱ access time and ～400kB , the Lookup scheme has achieved very high speed lookup time about 100㎱ for 2 memory accesses

As the operating frequency of digital modules in network system becomes fast, integrity of signals between modules is regarded as a important factor in high speed system design. To guarantee the signal integrity, many factors that deteriorate quality of signal should be considered. In this paper, we survey many factors which be considered while in designing and imp]ementing the backplane for high speed router and analyze the simulation result and experimental result.

As digital systems continue to use components with faster edge rates and clock speeds, transmission of the digital information in these systems approaches the microwave realm. At these speeds digital signal fidelity becomes both a critical success factor and design challenge. The noise sources in digital systems include the noise in power supply, ground and packaging media due to simultaneous switching of drivers, signal reflections and distortions on single and multiple transmission lines. This paper presents theory, case studies and design considerations of gigabit interconnection for network and communication systems. The case studies show HSPICE and Ampredictor simulations of alternate approaches. Various subjects including skin effect and dielectric losses, interconnect simulations and crosstalks of connector, affected signal discontinuity, are addressed.

One major drawback of conventional output buffered switches is that the speed of writing cells into output buffer should be N times faster than input link speed. This paper proposes a new output buffer switch that divides one output buffer into several buffers and virtually shares the divided buffers by using a distributor. The proposed switch makes it possible to reduce the memory speed. The proposed switch is evaluated in terms of the average cell latency compared with the input buffered switches which use the arbitration alogorithms, i.e., iSLIP or wrapped wave front arbiter(WWFA).

This paper analyze link-sharing mechanisms in packet networks based on the hierarchical class based queueing. The CBQ outlines a set of flexible, efficiently implemented gateway mechanisms that can meet a range of service and link-sharing requirements. We have analyzed the Class level(B, C, D) using the EWMA (Exponential Weighted Moving Average) weight value and EWMA average limit value.

This paper describes on the threats in the MPLS Network. Also we discuss on attack scenario that are Unauthenticated Access, Data disclosure and Data modification. Finally we discuss and suggest the best various Security of solutions in MPLS network

본 논문은 ATM교환기에서 Non-ATM정합을 위한 미디어게이트웨이의 개발방안과 하드웨어, 소프트웨어 구조에 대해서 기술한다. 미디어게이트웨어의 하드웨어 구조는 ATM계층처리보드와 다중화처리보드 및 서비스보드들로 구분되며 Non-ATM을 서비스별로 처리할 수 있는 보드를 모듈당 최대 8매까지 실장 할 수 있다. 다중화처리보드는 ATM셀 MUX/DEMUX기능과 IPC송수신기능을 처리하고 서비스보드의 링크상태관리, 운용기능을 수행한다. 서비스보드의 종류는 프레임릴레이, 회선대행, AAL2 트렁킹, N-ISDN중계선 연동기능을 각각 수행한다.

In this paper, a Inter-Working Function Unit(IWF) has been developed and designed in order to change to advanced subscriber system the Remote Subscriber System(RSS) that is operating with simple services(PSTN Function only). Regarding the cost and the effectiveness, RSS should be connected to Access Subscriber System with PCM cables directly. As this method being used, in the period of Retrofit, the connecting job covering RSS will be handled easily and safely.

In this paper, we propose VC merge capable hardware architecture for scalability based on ATM switching fabric. We implemented a scheduler for configuring crossbars in input-queued switches which support virtual output queues at the input ports. Also, we implemented VC merge capable scheduler at the output ports. We verified the proposed model by using C language, and designed with VHDL language. Then, we simulated and synthesized it with software of the SYNOPSYS corporation.

ATM is the switching and multiplexing technology chosen by the ITU-T for the operation of B-lSDN. Basically, ATM technology is designed to combine the reliability of circuit switching with the efficiency and flexibility of packet switching technology. For servicing QoS in IPOA(IP over ATM) when the larger effort is given, it will be the good method that the original QoS benefits having ATM switching have in ATM layer underlying layer. The IETF has recently proposed Differentiated Services framework for provision of QoS. In this paper we analyse performance of two Diffserv mechanism. Threshold Dropping and Priority Scheduling. Threshold Dropping and Priority Scheduling can be regarded as basic mechanisms from which the other mechanisms have been derived. Hence comparative performance of these two mechanisms in providing required QoS is an important issue. In this Paper we carry out a performance comparison of the TD and PS mechanisms with the aim of providing the same level of packet loss to the preferred flow. Our comparison of the TD and PS allows us to determine resultant packet loss for the non-preferred flows as a function of various parameters of the two mechanisms.

Multicasting is the delivery of a packet simultaneously to one or more destinations using a single, local transmit operation. Typically the set of destinations is referred to as a multicast group. sources transmit to these group addresses without knowing the group's actual membership. We have studied an implementation of one model of supporting IP multicast over ATM, the Multicast over ATM model developed by the IETF(Internet Engineering Task Force). MCOA(Multicast over ATM) that includes both these modes of operation and the behavior of each in a testbed where the ATM host were connected in a WAN and LAN. WAN topology was to gain insight into the effects of larger propagation delays on the MC over ATM model.

In this paper, a 0.5W, 2GHz high-efficiency class A power amplifier using the dynamic bias control is proposed. First of all, the drain bias control amplifier is analyzed theoretically and designed with commercial devices. Simulation results show that the proposed amplifier has a significant improved efficiency, compared to fixed bias power amplifier.

본 논문은 전력증폭기 정합회로 설계시 주어진 임피던스를 가지고 Ansoft사의 Ensemble을 이용해 기본적인 정합회로를 설계하였다. MHL21336 , MRF21030 ,MRF21125로 대전력 증폭기를 설계 및 제작하여 측정해본 결과 전체 이득이 52㏈, 대역폭 안에서 이득 평탄도는 ±0.37㏈ 정도, 출력이 PEP 5l㏈m에서 -30㏈c의 결과를 얻었다. Bias 전류에 대한 5㎒ Tone-space IMD 특성곡선을 측정해 본 결과 기지국용 대전력 증폭기로 사용할 수 있음을 보였다.

This paper has been studied a rower amplifier for IMT-2000 handset. Circuit design is performed and optimized by using HP ADS RF software. Designed amplifier consist of 2 stage, has 25㏈ gain, over 27㏈m output power and about 40% power efficiency. Power amplifier operation frequency range is 1955${\pm}$70MHz. Mask layout of the designed Amplifier consisting of 4 mask. The measured results of these values are satisfying the specification of IMT-2000 handset.

In this paper, we made 5W 2stage power amplifier for IMT-2000 repeater. We designed this amplifier by harmonic balanced simulation using nonlinear model to minimize distortion. After simulation, we acquired 47㏈m 1㏈ compression point at 2110 ~ 2170MHz single tone input. In addition, the ACPR of this amplifier was good. The test result was 47㏈m 1㏈ compression point, 42.6㏈ gain, -36.16㏈c ACPR at 2.5MHz, -44.34㏈c ACPR at 5MHz and -51.67㏈c ACPR at 7.5MHz.

This paper describes a CMOS low noise amplifier (LNA) with bias current reusing architecture intended lot use in the front-end of IMT-2000 receiver. It has been implemented in a 0.35$\mu\textrm{m}$ CMOS process with two poly and four metal layers. In order to accuracy of simulation, we considered a bonding wire and a pad effect and used the measurements of capacitors and on-chip inductors which implemented in the same process. The LNA has a forward gain (S21) of 17 ㏈ and a noise fjgure of 1.26 ㏈. And it has a third-order intermodulation intercept point (IP3) of +3.15 ㏈m and a 1㏈ compression point (P1㏈) of -16 ㏈m, input referred, respectively. The power consumption is 19 ㎽ from a 3V supply.

In this paper, I compared some characteristics between HPA and LPA using Feedforward method. Feedforward method is known for best IMD correction. HPA generated 46.5㏈c at 45.5㏈m output power. But, using feedforward linearing method, I could improve IMD to 67.17㏈c at the same output power. IMD could be improved 20.67㏈ at 45.5㏈m output power. I measured average power, IMD, total current, and efficiency of two amplifier at many different power levels. I could get about 70d3c IMD using feedforward method.

Advanced FeedForward method use Predistortion method and FeedForward method simultaneously. This method better than original Feedforward method in linearity and supply smaller power to pre-power amplifier than different methods, and then it has higher power efficiency and better linearity than original Feedforward method. A linear power amplifier using Advanced feedforward method is designed and fabricated for IMT-2000 transmission system (2110㎒ -2170M㎓). This amplifier's power gain is about 40㏈ and it's 3-rd IMD(Intermodulation distortion) are smaller than about -55㏈c(@ 10MHz).

In this paper, A Feedforward Linear Power Amplifier for IMT-2000 which IMD characteristics was improved was designed and fabricated. To improve the main power amplifier IMD characteristics, the Feedback loop was added to basic Feedforward Power Amplifier structure. Therefore, the output power of error amplifier can be reduced, and it is easy to control the linearization circuit to cancel total IMD. The designed power amplifier represented the 40㏈m(l0W) output power and -55㏈C 3rd IMD at Center frequency 2.14㎓ (@5㎒).

In this paper, predistorter for PCS has been designed and fabricated. In predistorter system IMD signal generator was very important element. In this LPA IMD signal generator was fabricated using main signal cancellation and error signal cancellation of feedforward method and two amplifier that had same IMD characteristics. This LPA showed IMD characteristics of 52㏈c operation in 48㏈m(60W) and made 12㏈ IMD characteristic improvement when it was excited by two tone. In this LPA, to make more IMD characteristic improvement the IMD characteristic resemblance between main amplifier and predistortion amplifier is very important.

Multi-bias parameter extraction technique for HEMT small signa] equivalent circuits is presented in this paper. The technique in this paper uses S-parameters measured at various bias points in the active region to construct one optimization problem, of which the vector of unknowns contains only a set of bias-independent elements. Tests are peformed on measured S-parameters of a pHEMT at 30 bias points. Results indicate that the calculated S-parameters is similar to the measured data.

This paper describes a parameter extraction method for HBT(Heterojunction Bipolar Transistor) equivalent circuit model without measurements of special test structures or numerical optimizations. Instead, all equivalent circuit parameters are calculated analytically from small-signal S-parameters measured under different bias conditions. These values being extracted from the cutoff mode can be used to extract intrinsic parameters at the active mode. This method yields a deviation of about 1.3 % between the measured and modeled S-parameters.

One of the problems using DCR(Direct Conversion Receiver) are DC offset, poor channel selectivity. APDP(Anti Parallel Diode Pair) can be good candidate for DCR frequency mixer due to its inherent End harmonic suppression. APDP shows good IP2 and DC suppression. This paper describe single APDP LO power characteristics, IP2, and receiver structure utilizing APDP frequency mixer

This paper describes image-rejection down conversion mixer for bluetooth application using 0.35u CMOS process. the proposed architecture is composed of LO phase shifter, mixer core, IF buffer, and IF phase shifter. IF phase shifter is designed using polyphase fillet. Simulation results show conversion gain = l0㏈, input 1㏈ compression point = -15.7㏈m. input third-order intercept point(IIP3) = -4.4㏈m, and image-rejection ratio = 37.8㏈, respectively, at 3V supply voltage, and 15.7㎃ current.

본 논문에서는 P-HEMT Gate-바이어스 튜닝에 의한 위상동기 마이크로파 발진기를 설계하였다. 설계된 유전체 발진기는 병렬궤환공진 형태로서 P-HEMT의 게이트단에서 전압을 제어하여 전압제어발진기 형태로 주파수를 가변시키므로서 안정된 위상동기신호를 나타나도록 하였다. 위상동기방식은 외부에서 제공되는 125㎒의 기준주파수를 SRD로 체배시켜 하모닉 신호를 이용한 마이크로파 샘플링 위상검파 방식으로 설계하였으며, 유전체 발진기의 자유발진신호와 샘플링 신호사이의 위상비교에 의하여 ±1㎒ 범위의 고안정 특성을 갖는 13.25㎓대역의 위상고정 발진기의 동기화와 저 위상잡음을 나타내었다.

Coplanar-type MIS transmission lines have been simulated using FDTD method and compared with the measured results and the simulated results of the reference paper［3］. We can confirm that our simulation results are similar to measured results compared to the previous simulated results of the reference paper. Moreover, variations of characteristic impedance by insulator thickness are calculated for the insulator thickness of 0.0,0.5 and 1.0$\mu\textrm{m}$.

In this paper, a new adaptive linearizer architecture with the predistorter is proposed. In the M.Ghaderi's paper, two analog predistorters and an envelope detector are used. Analog circuits for the analog predistorter and the envelope detector can cause imperfection and inaccuracy of the system and make circuits more complex. To solve those problems, most of processes including the predistortion are made by the DSP. The RLS algorithm is applied so that the errors between power amplifier output signals through the postdistorters and predistorted input signals can be converged to the global minimum.

In this paper, we designed and fabricated a low noise amplifier which can be used in W-CDMA. For improving input VSWR and stability an emitter inductance series feedback was used, and for acquiring higer linearity at low current DC bais by-passing method was used. Fabricated low noise amplifier had 15.33 ㏈ power gain, 2.17 ㏈ NF, -9.53 ㏈ $S_{11}$ and -35.91 ㏈ $S_{22}$ at 2.16 GHz, and +5.34 ㏈m II $P_{ 3}$ at 10 MHz channel spacing.g.g.g.

In this paper, the Ka-band Dielectric resonator oscillator has been designed and fabricated. The resonator network was simulated using HFSS program. The design method of an oscillator is the small-signal S-parameter design. The Push-push DRO employs a hetero junction FET (NE32484A). The fabricated Push-push DRO shows such characteristics as the phase noise -106 ㏈c/Hz at the 100 ㎑ frequency offset. the output power and fundamental frequency surpression were -6 ㏈m and -29 ㏈c, respectively.

Electronics and Telecommunications Research Institute (ETRI) developed the Ka-band satellite communications payload. This system is able to provide a high data rate communication service with a bandwidth of 200 MHz, a wideband digital flunking services up to 155 Mbps and asymmetrical internet multimedia service. The system employs the common receive/transmit antenna and the 2-for-1 redundant scheme for the LNA-Downconverters. The different types of high power amplification, TWTA for one chain and SSPA for the other chain, are used lot the variety of experimental options. For the reliable test of the payload, EGSE was also developed. The parametric RF tests were carried out in order to measure the performance of Ka-band communication subsystem, in most case the results of RF performance test complied the payload requirement.

Repeater Duplexer of 800MHz band consists of 4pole transmitter band pass filter, receiver band pass filter and branch circuit. Circuit parameter of Duplexer such as coupled capacitance of equivalent circuit was drawn out and used to coupled line characteristics impedance (Zoo, Zoe) that satisfied resonator condition and attenuation condition. Simulation was carried out by the ADS(Advanced Design System) were obtained good attenuation characteristics (869~894MHz： 65㏈(Min.),824~349MHz： 65㏈(Min.)

Telecommunication system demands for increased bandwidths and operating frequencies for analog signal processing could be satisfied in the near future by the emergence of a novel technology based on magnetostatic waves propagating in low loss ferrimagnetic films. The magnetostatic wave is the only available technology for analog signal processing directly at millimeter wave frequencies. This paper has been studied the design and implementation of a Magnetostatic Surface Wave band-pass filter for LMDS system.

We designed and fabricated partially shorted MSA with a slot for 850 MHz on Copper-clad Laminate substrate, where the width of the radiation patch is identical with that of the ground plane and one side of the radiation patch is partially shorted to the ground plane. The radiation patterns of ZX, XY and ZY planes were measured. As a result, a better co and cross polarization lot ZX plane was obtained, compared to the partially shorted MSA without a slot.

In this paper we have implemented CH-MUX system which provides customers with various services, i.e. POTS, ISDN, digital leased line and so on, and supports not only UDLC but IDLC network configuration based on existing optical transmission facilities. Also the RCS equipment has been designed and implemented for remote monitoring and control of CH-MUXs. And then this paper has described IPC procedure and proposed other implemental methods of IPC channel. Service providers will be able to design and construct cost-effective access network with RCS and CH-MUX systems.

RFC 2271에는 망 관리 플랫폼인 SNMP architecture를 더 이상의 수정을 가하지 않는 모듈구조로 정의되어 있다. 즉, SNMP application을 개발함에 있어 새로운 application을 추가할 때, 기존의 software 에 수정을 가하지 않는 것이 중요한 요소이다. 이 논문에서 제안하는 subject-oriented programming은 위에 언급한 관점에 주안점을 둔 방법으로 기존에 개발된 SNMP application의 기본구조를 유지한 채 software를 개발할 수 있는 방법이다. Subject-oriented programming은 object-oriented programming에 기초를 두고있다.

In this paper, the design and the implementation of a realtime monitoring system using WWW protocol over the Internet is described. The overall system architecture and the functional structure of the system are presented. A Java applet is used in the development of the system for the motion picture effect of JPEG still images. The system is tested on a LAN and the experimental results are described.

본 논문에서는 ITS(Intelligent Transport System) 서비스를 위한 기반시설로 도입이 예상 되는 DSRC(Dedicated Short Range Communication)시스템에 대하여 시스템의 개요와 특징, DSRC시스템을 이용하여 주차장에서의 요금정산을 자동화하기 위한 시스템의 구조 및 구현방법에 대하여 제안하였다.

본 논문은 B2C기반의 전자상거래 쇼핑몰에서 후불방식의 전화번호에 상품 구매 대금을 지불할 수 있도록 하는 전화요금결제 시스템의 구성 및 기능에 관한 것이다. 전화요금결제 게이트웨이 (Telephone Payment Gateway ： TPG)는 기존 웹/머쳔트 서버 (Web/Merchant Server), 고객관리 시스템 및 요금관리 시스템과 TCP/IP를 기반으로 하여 연동되어, 쇼핑몰 가입자에게 신용카드, 전자화폐 wallet, on-line 입금 등의 지불 방식과는 다른 지불 방식을 제공함으로써, 지불 방식의 다양화를 도모할 수 있고, 인터넷 사용자 대부분이 가지고 있는 PSTN/ISDN 번호를 가지고 쇼핑몰 상품 대금을 지불할 수 있어서, 전 국민을 가입자로 확보할 수 있는 서비스이다.

With the unprecedented growth in internet traffic, demand for larger, more scaleable IP backbone networks is seemingly limitless. This critical requirement is leading the DACOM to investigate architectural alternatives for cost effective, scaleable and flexible IP backbones. In this paper, we present three alternatives for IP backbones using DWDM systems and multi-gigabit IP Routers in the DACOM metro networks, and then compare them by performing an economic analysis.

In this paper, capacity of a multicarrier DS/CDMA system is analyzed and simulated in a Nakagami fading channel. It is confirmed that the adaptive antenna array is a very efficient solution to enhance system capacity of a multicarrier DS/CDMA system. The results in this paper can be applicable to receiver design for the third and fourth mobile communication systems.

In order to meet the different requirements of a wide variety of user applications, the network should support the different quality of service requirements for different applications. While 3GPP has specified a number of QoS profiles for a 3G-GPRS (or UMTS), the implementation of QoS management is an issue. This paper presents the QoS management functions in the 3G-GPRS. The QoS management involves service manager, translation function, admission/capability control, and subscription control of users, and mapping function, classification function, resource manager, and traffic conditioner of user traffic. It also describes the QoS Management procedure during the session management when setting up the bearers.

This paper covers the performance testing for layer 3 Ethernet switch based on various methodologies by which we can measure essential metrics such as throughput, latency, frame loss rate, and back to back frames. In the first place, layer 2 and layer 3 switch evolution is introduced followed by description of IP packet switching in layer 3 switch. And then, the above test metrics and test methodologies are illustrated as well. At last, we conduct the performance testing for layer 3 switch in case of transmitting packets of 64, 128, 256, 512, 1024, 1280, and 1518 byte size and analyze then results.

This paper considers a scheduling algorithm for high-speed routers, where the router has an N x N port input-queued switch and the input queues are composed of N VOQ(Virtual Output Queue)s at each input port. The major concern of the paper is on the scheduling mechanism for the router. The paper discusses the preferred levels of the performance measures and then develope a non-linear mixed integer programming. Additionally, the paper suggests a heuristic scheduling algorithm for efficient and effective switching.

The economical detection of dual-tone multifrequency(DTMF) signals is an important factor when developing cost-effective telecommunication equipment. Each channel has independently a DTMF receiver, and it informs the detected signal to processors. This paper analyze the power spectra and evaluate the performance of DTMF receiver by using the quick Fourier transform(QFT) algorithm. As experimental results, it show the improved performance to the DTMF receivers and reduce memory waste and process the real-time.

This paper describes IMT-2000 Testbed System which consists of ATM based IMT-2000 exchange(A-lMX), RNC simulator, HLR simulator, SCP simulator, B-ISDN subscriber simulator and MS simulator. Simulators were developed to verify the mobile functions and basic services of IMT-2000 like Videophone, VoD(Video on Demand), and Internet access. UPT(Universal Personal Telecommunication) service could be adapted well to this testbed system. Until the entire network elements are developed fully, this testbed system can be used to prove new services in IMT-2000 network.

The effect of code selection for a multicode DS/CDMA system is evaluated for a high deta rate transmission, The performance is evaluated in terms of bit error and outage probabilities. The multipath fading channel is modeled as a Nakagami-m distribution which has been known to be appropriate to model the multipath fading in urban as well as indoor channels. From simulation results, it is shown that the concatenated sequence of Walsh code and Gold sequence is most promising among many code selections. The considerations in this paper can be applied to the next-generation mobile communication systems such as IMT-2000 which requires high bit rate transmissions.

본 논문에서는 위성통신 환경에서 DS/CDMA DPSK 시스템의 성능을 분석한다. 성능분석의 척도로 비트오류확률을 사용한다. 위성전송로는 쉐도잉이 있는 라이시안 페이딩 전송로로 모델링한다. 수치계산의 결과, 위상잡음이 존재할 때 비트오율 성능이 저하되므로 시스템 용랑이 감소될 것이 예상된다. 또한 위성전송로에서는 쉐도잉이 시스템 전체 성능에 커다란 영향을 미침을 알 수 있다. 본 논문에서의 분석은 DS/CDMA 기반의 위성통신 시스템 설계에 적용할 수 있다.

The interference situation for the satellite networks using non-geostationary satellite orbit (NGSO) is more complicated than the situation between geostationary satellite orbit (GSO) networks because of the time varying orbital characteristics of NGSO systems. Most of frequency bands are allocated to fixed-satellite service and liked-service in co-primary basis. In this paper, the sharing criteria between NGSO/FSS systems and HDFS (High Density Fixed-Service) are examined.

Security-related issues in mobile communications are increasing. The security requirements of mobile communications for the mobile users include authentication of the mobile user, the data confidentiality, the data confidentiality and the location privacy of mobile user. These services require security features compatible with the wireline networks. However, wireless networks have many restrictions compare to wireline networks such as the limited computational capability of mobile equipment and limited resource(bandwidth) between a mobile user and a fixed network. So, security features for IMT-2000 are designed to meet the limited capacity. In this paper, we analyze the required security features and mechanism, and design network access security feature effective for IMT-2000 Systems. The design includes security functions allocation to each system. Finally, discuss the computational power of each system based on at]coated functions to it

WDM is a very promisinig technique for the realization of future All-Optical networks. WDM gives an advantage of high rate transmission without delay for Electronic/optical conversion. But the available number of wavelengths is limited by technical restriction. so the efficient optical path routing and wavelength assignment is needed. this paper is concerned with the efficient design of WDM optical transport networks. RWA assumes that the connection demands between node pairs are given. the objective of RWA is to minimize the number of wavelengths. these design consider the static routing and wavelength assignment in the network of arbitrary topology. To solve these problems, this paper proposes some heuristic algorithms.

Open Shortest Path First(OSPF) is a dynamic, hierarchical routing protocol designed to support routing in TCP/IP networks. Currently, OSPF is used as Interior Gateway Protocol(IGP) in many routers. In this paper, we analyze the variation of number of OSPF routing packets in case of changing the network configuration. The results show that the number of packets in case of adding new link increase five times than one in case of normal operation.

In this paper, we describe the design and implementation of IPv6 LAN. The legacy protocol for Internet is IPv4(IP version 4). The ability of IPv4 is not enough for modern real time multimedia communication services. So IPv6(IP version 6) protocol was suggested to resolve the problems of IPv4. We implemented IPv6 LAN using sTLA(sub Top Level Aggregation identifier) address and KOREN(KOrea Research and Experimental Network). Our IPv6 LAN is connected with 6TAP(Chicago), WIDE(Tokyo), and SingAREN(Singapore). We used a dedicated router, Windows 2000 PC host FreeBSD PC host, Solaris 7 workstation and Solaris 8 workstation for IPv6 NDP(Neighbor Discovery Protocol) protocol test. To support all data services including voice and video, IP protocol should be enhanced because the characteristics of modern network services are requiring QoS(Quality of Service) functions, auto-configuration, security, mobility and so on. So a new IP protocol, IPv6, has been developing to meet the requirements. In this paper, we introduce the implementation method and configuration information of IPv6 LAN.

This paper proposes to design the residential power line communication device using Softwire Protocol, which targets the device with 8bit micro-controller and small-size memory based on low-rate power line communication network or wireless communication network. As a case study, the SCP message specification of air-conditioner that has capability of control and monitoring its status is designed using Softwire Protocol. And, it is described how the device operates sequentially.

Film Bulk Acoustic Wave Resonator(FBAR) used in microwave region was analyzed with Finite Difference Time-Domain Methods(FDTD) in this paper. FBAR have been analyzed with one dimensional Mason model analysis or Finite Element methods(FEM), but the first couldn't analyze effect of area variation and spurious characteristics, the second had difficulty in element separation because of thin electrode. So in this paper FBAR was analyzed by Finite Difference Time-Domain Methods and it's results were transformed to frequency domain using Discrete Fourier Transform.

This paper presents a slotted leaky waveguide antenna using a rectangular waveguide for mobile reception of DBS (Direct Broadcasting Satellite). A slotted rectangular waveguide in leaky-wave operation can obtain a large beam-tilting angle of 45$^{\circ}$, which is an attractive candidate of mobile DBS receiving antennas because it can be installed horizontally. SNM is used to solve arbitrary shape and materials constant, derived from maxwell's equations. In this paper, analyze cross slot waveguide antenna using SNM. and verify by HFSS.

There are many researches to increase bandwidth of the microstrip patch antenna for wireless LAN. In spite of broad bandwidth, Bow-Tie microstrip patch antenna, broadband microstrip patch antenna, has disadvantages that are low gain and big size. In this paper, stacked Bow-Tie microstrip patch antenna for wireless LAN is designed in 5.725∼5.825㎓ band. This antenna has characteristics that are broadband bandwidth, high gain and small size compared with microstrip patch antenna. In simulated results, the return loss is -34.2㏈ at 5.78㎓ and bandwidth is 11.345% for VSWR 2：1 and 7.75% for VSWR 1.5：1. In measured results, the return loss is -38.45㏈ at 5.78㎓ and bandwidth is 13% for VSWR 2：1 and 5.6% for VSWR 1.5：1. It has 59.37$^{\circ}$-3㏈ beam width and 6.5㏈ gain.

The classical image reconstruction for stripmap SAR is the range-Doppler imaging. However, when the spotlight SAR system was envisioned, range-Bowler imaging fumed out to fail rapidly in this SAR imaging modality. What is referred to as polar format processing, which is based on the plane wave approximation, was introduced for imaging from spotlight SAR data. This paper has been studied for the raw data processing schemes in the spotlight-mode synthetic aperture radar. we apply the wavefront reconstruction scheme that does not utilize the approximation in spotlight-mode SAR imaging modelity, and compare the performance of target imaging with the polar format inversion scheme.

The success of target reconstruction in SAR(Synthetic Aperture Radar) imaging system is greatly dependent on the coherent detection. Primary causes of incoherent detection are uncompensated target or sensor motion, random turbulence in propagation media, wrong path in radar platform, and etc. And these appear as multiplicative phase error to the echoed signal, which consequently, causes fatal degradations such as fading or dislocation of target image. In this paper, we present iterative phase error estimation scheme which uses echoed data in all temporal frequencies. We started with analyzing wave equation for one point target and extend to overall echoed data from the target scene - The two wave equations governing the SAR signal at two temporal frequencies of the radar signal are combined to derive a method to reconstruct the complex phase error function. Eventually, this operation attains phase error correction algorithm from the total received SAR signal. We verify the success of the proposed algorithm by applying it to the simulated spotlight-mode SAR data.