Usually, the thrust is calculated by magnetic equivalent circuit modelling method for thrust capacity and accuracy progress of position control about a Linear Pulse Motor of which position precision is good and open-loop control is possible within Linear Motors. Analytical thrust deviation exists to calculating magnetic flux density by using Permeance Modelling Method, Finite Element Method, and Velocity Electric Motive Force Method. For calculating accuracy thrust by using these every method, the thrust is calculated and compared by Lorentz Force Method, Magnetic Coenergy Method, and Maxwell correspondence force Method. And that becomes important factor at the comparison of each capacity and parameter of Motor. So this study wants to compare and analyze measurement data and calculating data of the static force of Linear Pulse Motor. and then we can get more accuracy method, calculating the static thrust of Linear Pulse Motor(LPM).

We propose that when combustible burn with contain carbon, introduce fire detector with sensor of private-use detectable light energy as infrared and ultraviolet in energy of electromagnetic-wave type radiate from flame, method for correct discrimination to resemble fire produce false alarm of detector such as sun light, hot object radiation, are welding. This research using infrared sensor is pyroelectric infrared sensor based black body radiation theory. Ultraviolet sensor is uv Tron using gas multiplication effect to current discharge and photoelectric effect of metal. To have high sensibility and to gain proper output voltage, it has high responsive performance. This research introduced UV/IR compound type flame detector and proposed method of false alarm reduced to resemble fire. The result propres the prevention and extinction of fire technique degree, certificated operation of detector.

The YBaCuO thick film was deposited by the electrophoresis in the solution with different dimension particles. The morphology of the films deposited from different particles size was compared. The powder made by sol-gel method has the submicron particles, which deposit the most smooth film, and without microcracks after sintering. After sintering of the deposited film, the zone-melting process was carried out in low oxygen partial pressure (100 Pa) and Ag was used as substrate. And the zone-melted YBaCuO was studied by XRD.

YBCO film을 이용하여 2 stripe-meander 형태의 초전도 한류기를 제작하고 시험하였다. 초전도 film의 hot spot에 의해 발생하는 열을 분산시키기 위해 gold shunt layer를 입혔다. 사고각 $0^{\circ}$에서 사고발생 후 최초 quench 전류값은 $9.56A_{peak}$이었고 약 0.63 msec동안 fast quench 가 진행되고 이후에는 gold층의 열발생에 의한 저항증가가 약 3주기동안 진행된 후 안정되었다. 사고각 $45^{\circ}$와 $90^{\circ}$ 에서는 전류가 상승하는 도중 혹은 최고지점에서 사고가 발생했기 때문에 fast quench time이 각각 0.56 msec와 0.26msec를 보였다. 초전도 한류기를 적용하였을 때 사고전류는 사고직후 약 5배, 3주기후에는 약 8.5배까지 효과적으로 제한함을 알 수 있었다.

The operational characteristics of flux-lock type high-Tc superconducting fault currentlimiters(HTSC-FCLs) was described and currents equation at each coil was derived from equivalent circuit. $YBa_{2}Cu_{3}O_{7-x}$(YBCO) thin film was used as the current limiting elements of the flux-lock type HTSC-FCL, which were fabricated by etching the YBCO thin film into 2 mm wide and 420 mm long meander line consisting of foureen stripes with different length. The 2nd peak on the current of coil 2 after a fault disappeared by current of the 3rd winding, which was installed in the flux-lock type HTSC-FCL.

In this paper, the new dual trench gate Emitter Switched Thyristor (DTG-EST) is proposed for improving snap-back effect which leads to a lot of serious problems of device applications. And the parasitic thyristor that is inherent in the conventional EST is completely eliminated in this structure, allowing higher maximum controllable current densities for ESTs. The conventional EST exhibits snap-back with the anode voltage and current density 2.73V and $35A/cm^2$, respectively. But the proposed DTG-EST exhibits snap-back with the anode voltage and current density 0.96V and $100A/cm^2$, respectively.

The sapphire wafers for blue light emitting devices were manufactured by the implementation of the surface machining technology based on micro-tribology. This process has been performed by chemical and mechanical polishing(CMP) process. The sapphire crystalline wafers were characterized by double crystal X-ray diffraction. The sample quality of sapphire crystalline wafer at surfaces has a full width at half maximum 89 arcses. The surfaces of sapphire wafers were mechanically affected by residual stress and surface default. Sapphire wafers's waveness has higher abrasion rate in the edge of the wafer than its center due to Newton's Ring interference.

산업의 고도화 및 도시의 집중화로 오염물질의 종류가 다양화 되었으며 여러 가지 오염물질 중에서도 비산 분진, 황산화물(SOx) 등은 연료 중의 특정성분을 제거하거나 연료를 대체하여 그 배출량을 줄일 수 있다. 그러나 질소산화물(NOx)의 경우에는 연료의 문제가 아니라 연소과정에서 반드시 발생되는 특징을 가진 오염물질이다. 이와 같이 환경오염물질의 제거기술에 있어 가장 중요하게 고려되어야 할 사항은 오염가스 제거의 효율성과 경제성이다. 따라서 본 연구에서는 사무실, 가정 등 주로 실내공기정화를 위하여 NOx 제거를 위한 선 대 평판형 플라즈마 반응기에 자석의 개수에 의한 자계세기 및 자속밀도 시뮬레이션과 도출된 시뮬레이션 결과를 바탕으로 제작된 반응기에 자석을 부가한 NOx 제거에 대한 실험을 하였다. 그 결과 자석을 부가한 경우가 NOx 제거효과에 있어 효율이 좋음을 알 수 있었다.

In this study, to measure the moisture of compaction, it is designed to use the 2neutron detectors. To perform the optimal design of their circuit, it is planned high voltage generator and voltage stable circuit and they are very suitable for detection demand. Also, it can be count to data calibration excluded count of ripple.

자발착화연소법과 분무열분해법을 동시에 적용한 초음파분무연소법을 이용하여 40~50nm 크기를 갖는 결정성 ZnO 분말을 합성하였다. 또한 바리스터로의 응용을 위해 Bi, Sb, Co, Mn을 초기출발원료인 Zn-nitrate에 첨가하여 복합조성의 ZnO계 바리스터 분말을 합성하였다. 합성된 바리스터의 분말을 성형 및 소결하여 전기적 특성을 관찰한 결과 Co를 첨가한 분말보다 Mn을 첨가한 분말에서 우수한 전기적 특성을 나타내었다.

This study proposes that the Phase Linearization Interpolation is higher efficency than the existed Orthogonal Frequency Division Multiplexing system in the Multipath channels time-varient. Also, it showed that time domain equalization is better than the existed frequency domain equalization about the calculation and efficency for clear Inter Carrier Interference of the doppler effect.

ITO (indium tin oxide) thin films on PET (polyethylene terephthalate) substrate have been deposited by a dc reactive magnetron sputtering without heat treatments such as substrate heater and post heat treatment. Each sputtering parameter during the sputtering deposition is an important factor for the high quality of ITO thin films deposited on polymeric substrate. Particularly, the material, electrical and optical properties of as-deposited ITO oxide films are dominated by the ratio of oxygen partial pressure. As the experimental results, the excellent ITO films are prepared on PET substrate at the operating conditions as follows: operating pressure of 5 mTorr,target-substrate distance of 45 mm, dc power of 20-30 W, and oxygen gas ratio of 10 %. The optical transmittance is above 80 % at 550 nm, and the sheet resistance and resistivity of films are $24\;{\Omega}$/square and $1.5{\times}10^{-3}\;cm$, respectively.

When a mobile robot moves around autonomously without man-made corrupted bye landmarks, it is essential to recognize the placement of surrounding objects especially for self localization, obstacle avoidance, and target classification and localization. To recognize the environment we use many Kinds of sensors, such as ultrasonic sensors, laser range finder, CCD camera, and so on. Among the sensors, ultra sonic sensors(sonar)are unexpensive and easy to use. In this paper, we analyze the sonar data and propose a method to recognize features of indoor environment. It is supposed that the environments are consisted of features of planes, edges, and corners, For the analysis, sonar data of plane, edge, and corner are accumulated for several given ranges. The data are filtered to eliminate some noise using the Kalman filter algorithm. Then, the data for each feature are compared each other to extract the character is ties of each feature. We demonstrate the applicability of the proposed method using the sonar data obtained form a sonar transducer rotating and scanning the range information around a indoor environment.

This dissertation is about the development of $BaTiO_{3}$-type PTC(Positive Temperature Coefficient) thermistor by composition method. PTC samples were fabricated after setting the experimental composition equation as $(Ba_{0.95-x}Sr_{0.05}Ca_x)TiO_3\;-\;0.01TiO_2\;-\;0.01SiO_2\;-\;aMnCO_3\;-\;0.2Nb_{2}O_{5}$ and their testing results were analyzed. a PTC thermistor, having the characteristics of relatively low resistance at room temperature and c and a good temperature coefficient, has been developed.

The paper is proposed to position and speed control of interior permanent magnet synchronous motor(IPMSM) drive without mechanical sensor. A minimum order state observer is used for the mechanical state estimation of the motor. The observer was developed based on nonlinear model of IPMSM, that employs a d-q rotating reference frame attached to the rotor. A minimum order state observer is implemented to compute the speed and position feedback signal. The validity of the proposed sensorless scheme is confirmed by various response characteristics.

This study evaporates ZnO layer thickness differently with RF sputtering method on Si Wafer(n-100). This study is performed to examine the characteristics of photon energy and dielectric loss according to the thickness of ZnO and increase the reliability and reproduction of ZnO thin film. It is confirmed that the variation of electric Permittivity by frequency is resulted from the formation of particles within thin film, the particle size and the polarization on grain boundary. Peak of electric Permittivity value of thin film has slower and less value in early low wavelength by the coulomb force involved in carrier combination according to the increase of frequency. Reversal of electric Permittivity values is induced by dipole polarization shown in the dielectric of thin film. Complex electric constant $({\varepsilon}_1{\varepsilon}_2)$ has larger peak values as it’s thickness is thinner and then it is larger according to the increase of frequency. Electric Permittivity by photon energy has large value in imaginary number and is reduced exponentially by the increase of carrier density according to that of photon energy.

This dissertation describes an optimization method for fabricating thick films with superconducting YBCO powders by electrophoresis technique. The lateral alternating applied voltage caused to shake the superconducting powder vertically to the deposition field during the process of the oriented deposition so that it was deposited along the c-axis on the silver tape with shaky-aligned EPD. As the result, the optimized thin film fabrication method was obtained to get more dense and uniform surface morphology as well as the improved critical current density. For commercial utilization and efficiency, in this dissertation, alternating voltage of 25-120 V/cm in frequency of 60Hz was proposed to apply it as a subsidiary source for shaky-flow deposition so that the fabricated thin film showed uniform surface morphology with less voids and cracks and $T_{c.zero}$ of 90 K and the critical current density of $3419A/cm^2$.

본 고에서는 현재 중국에서 추진되고 잇는 과학기술진흥시책을 과기공관계획(科技攻關計劃)을 중심으로 조망해 보고, 특히 863 계획과 973 계획에 대한 총제적인 내용을 소개한다. 863 계획은, 7차경제개발5개년계획 기간(75기간)부터 시작된, 고급기술 연구개발에 대한 집중적인 진흥 정책이며, 973 계획은, 9차경제개발5개년계획 기간(95기간) 중에 시작된, 기초연구분야에 대한 집중적인 진흥시책이다. 중국의 경우 이와 같은 국가 주도적인 진흥책은 중국공산당중앙위원회(중공중앙(中共中央))와 국무원의 방침 결정에 따라 집중육성(중점(重点))의 항목 결정 및 관리를 유관부문이 상호 협조하에 분담하여 지원하고 있다.

For the safety driving of an automobile which is become individual requisites, a new Neural Network algorithm which recognized the load vehicles in real time is proposed. The proposed neural network technique is the real time computation method through the inter-node diffusion. In the network, a node corresponds to a state in the quantized input space. Each node is composed of a processing unit and fixed weights from its neighbor nodes as well as its input terminal. The most reliable algorithm derived for real time recognition of vehicles, is a dynamic programming based algorithm based on sequence matching techniques that would process the data as it arrives and could therefore provide continuously updated neighbor information estimates. Through several simulation experiments, real time reconstruction of the nonlinear image information is processed. 1-D LIPN hardware has been composed and various experiments with static and dynamic signals have been implemented.

Today, stage technology is developing highly by application of digital computer. Performance is composed of audio/video and acoustic technology takes very important position in field of stage technology. Generally speaking, four factors of sound are loudness, pitch, sound timbre and duration. Loudness depends on sound pressure level, yet partly related with spectrum and dulation. Pitch depends mainly on frequence and have a relation with sound pressure and duration. sound timbre depends strongly on spectrum and have a relation with frequence. In this paper, I designed a multi-microphone system which can used in broadcasting and performance stage with vicboss 200MHz-VHF wireless microphone and vicboss 900MHz-VHF wireless microphone. I also studied about multi-microphone which can use conveniently in the super play that needs many microphones. If this multi-microphone is prodused, we could expect better sound quality and a big progress in stereo recording technology.

산업화에 기인하여 공장 및 수송수단 증가로 대기배출가스량이 증가 그 결과 대기오염이 심화되어 가고 있다. 그러므로 실내오염가스의 정화가 우선적으로 고려되어야 하므로 이러한 오염된 공기를 제거 할 수 있는 장치의 개발이 절실히 요구되어지고 있다. 본 연구는 환경오염물질 제거를 위한 선 대 평판형 플라즈마 반응기 제작에 필요한 최적조건을 도출하기 위하여 반응기 내부의 전위 및 전계분포에 대한 시뮬레이션을 하였고 여기서 도출된 결과를 바탕으로 플라즈마 반응기를 제작하고자 한다.

Depth error correction effect for maladjusted stereo cameras with calibrated pixel distance parameter is presented. The camera calibration is a necessary procedure for stereo vision-based depth computation. Intra and extra parameters should be obtain to determine the relation between image and world coordination through experiment. One difficulty is in camera alignment for parallel installation: placing two CCD arrays in a plane. No effective methods for such alignment have been presented before. Some amount of depth error caused from such non-parallel installation of cameras is inevitable. If the pixel distance parameter which is one of intra parameter is calibrated with known points, such error can be compensated in some amount. Such error compensation effect with the calibrated pixel distance parameter is demonstrated with various experimental results.

본 고에서는 현재 중국에서 추진되고 있는 고등교육 부문에 대한 진흥시책을 "211공정(工程)"을 중심으로 조망해보았다. 등소평의 중점대학 육성 구상에 따라 중국 국내의 제반 여건을 고려하여 "구오(九五)"기간 중에 개시된 "211공정(工程)"의 주요내용은 국가중점대학(國家重點大學)과 국가중점학과(國家重點學科) 건설 사업이다. 강역민(江澤民) 집권 후에는 "과교흥국(科敎興國)"을 기본국책으로 설정하여 교육부(敎育部)내의 과학기술사(科學技術司)에서 기지건설과 인재양성을 중점적으로 담당하면서 과학기술교육을 고등교육 발전의 기본축으로 삼아 적극적으로 추진하고 있다. 중국의 경우 이와 같은 국가 주도적인 진흥책을 중국공산당중앙위원회(중공중앙(中共中央))와 국무원의 방침 결정에 따라 집중육성(중점(中点)) 항목 결정 및 관리를 국무원 산하 유관부문이 상호 협조 하에 분담하여 지원하고 있다.

The purpose of this study is to find problems of "Electricity equipmentand" and "Electricity practic II" tectbook applied in 6th Technical High School Curriculum and to make direction of "Power equipment II" textbook applied in 7th Technical High School Curriculum. The method of this study is questionnaire survey. 120 teachers of 40 schools were selected by cluster sampling method. The main findings of this study are as follow. 1) We should make the composition of textbook easy. 2)The illustration, photograph and drawing of textbook are fitted well. 3) "power equipment II" textbook applied in 7th Technical High School Curriculum would contented follows : lighting equipment, elevator equipment, broadcasting equipment, interphone equipment.

고온초전도테이프의 전력부야 응용에서 자화손실과 함께 매우 중요한 통전손실에 대한 실험적 조사 연구를 한 결과, 외부자장이 커짐에 따라서 직류전압이 급격히 증가하였으며, 자장의 세기가 동일할지라도 교류인 경우가 직류인 경우보다 대단히 크다. 그리고 외부교류자장에 대한 직류전압-전류 특성으로부터 정의되는 동저항 또한 외부교류자장의 세기에 따라서 상이하지만 테이프의 임계전류에서 전기저항$(3.7\;{\mu}{\Omega}/m)$과 비교하여 작게는 수배에서부터 크게는 수백 배까지 증가한다.

LIM have mainly different point considering rotary induction motor, that is end effect. In this paper described that, end effect, adding to the rotary induction motor. They can designed because of affects magnetizing inductance and series resistance in the d-axis circuit. After LIM modeling, using SVPWM, apply to vector control this model. We can verify feasibility of field oriented control technology can control speed by simulation.

The use of the midnight power faces the crisis of the load peak-cut problem. Which appears at the simultaneous start of the midnight power system. We suggest a control method which uses the characteristics of boiler system. The system used that method consists of 6 heaters and are designed for the load distribution on each heater. Proposed method can take the balance of load during full time of midnight power supplied. The system is composed of measurement part and heater controller. Taking the data of the experience as a reason, the algorithm make the midnight power distribute. Experimental results show the validity of the method and the system proposed.

Thermal imaging system is electro-optical imaging device which can make visible the difference of infrared energy naturally emitted by objects. It is acquire the same images at any time of the day or night. There it has been readily available to the night observation such as fire control systems. In this study, we are manufacturing thermal image Al flat mirror. The surface roughness 3.539nm Ra and power 0.382 fringe(at 632.8nm), irregularity 0.835 fringe(at 632.8nm) for form waviness of thermal image Al flat mirror are very satisfied. The results will be reflected for development of the ultra precision application. And a brief review of Ultra-precision system in the field of Ultra-precision at Korea photonics technology institute (KOPTI) is present in this paper.

자기부유기는 전자력을 이용해서 쇠구슬을 공중에 떠있게 할 수 있는 장치이다. 본 논문에서는 자기 부유기의 기본 원리와 모델링에 관해 소개하고, 디지털 신호처리와 PWM전력변환기를 사용한 자기 부유기를 직접 제작하고 실험을 통해 성능을 검증하였다. 자기부유기의 원리는 고속회전기에 사용되는 자기베어링이나 자기부상 열차의 부상 시스템에 응용될 수 있다. 또한 전기공학 분야의 다양한 교과과정에서 습득한 지식을 활용할 수 있는 학부 프로젝트 실험 주제로 적합하다.

알루미나볼 위에 Titanium tetraisopropoxide(TTIP)를 원료로, 화학기상증착법으로 제조된 $TiO_{2}/Al_{2}O_{3}$ 볼을 이용하여 벤젠의 기상 광 분해 실험을 실시하였다. 기상분해 과정의 연속적 측정을 위하여 순환식의 반응장치를 자체 제작하였으며, PID(Photo Ionization Detector)방식의 VOCs meter를 이용하여 광조사에 의한 벤젠의 분해율을 실시간으로 측정하였다. 기상의 벤젠과 $TiO_2/Al_{2}O_{3}$ 볼의 원활한 흡착을 위해 30분간 암반응 시킨 후 광분해율을 측정한 결과 광조사에 의한 분말표면에 흡착된 VOCs의 탈착에 의한 초기 농도증가 현상이 공통적으로 측정되었으며, 흡착 면적이 작을수록 농도 증가 또한 낮게 측정되었다. 또한 최적조건을 기준으로 실시한 분해 실험 결과 60ppm이상의 고농도 영역에서는 VOCs의 분해가 비교적 느리게 진행되었지만, 60ppm이하의 저농도 영역에서는 급속한 VOCs의 분해가 측정되었다. 마찬가지로 반응 표면적이 넓을수록, 광원이 많을수록 그리고 광분해에 사용된 자외선 램프의 강도가 클수록 광반응에 의한 벤젠의 분해율이 증가하였다.

In URD(Underground Residential Distribution) power cable, experiments of WVT(Water Vapor Transmission) test on the Base Resin accomplished to specimens which contained CB(Carbon Black), anti-oxidant to base resin and made by pressing to resin of pellet or lump form. a kind of specimens was HDPE(High Density Polyethylene), MDPE(Medium Density Polyethylene), LDPE(Low Density Polyethylene), LLDPE(Linear Low Density Polyethylene), PVC(Polyvinyl Chloride). as a results of WVT test, we saw that WVT ratio was HDPE < LLDPE < MDPE≒LDPE${\ll}$ PVC. WVT properties of PVC using for jacket showed properties 15-20 times more than MDPE or LLDPE. Therefore, to development of watertightness cable, our works present need of Changing in insulating materials.

In this study, to measure the density of compaction, it is designed to use the 5 gamma-ray detectors. The developed instrument consists of measuring circuits for gamma-rays and thermal neutrons, a high voltage supply unit, stable circuit unit, count circuit unit and a microprocessor. To read count pulse from gamma-ray detectors are very accurate and it can be count to data calibration excluded count of ripple.

In this study, the DC dielectric breakdown of epoxy composites used for PCB material was experimented and then its data were simulated by Weibull distribution equation. The more hardener increased the stronger breakdown strength at low temperature because of cross-linked density by the virtue of ester radical, and the breakdown strength of specimens with filler was lower than it of non-filler specimens because it is believed that the adding filler forms interface and charge is accumulated in it, therefore the molecular motility is raised, the electric field is concentrated, and the acceleration of electron and the growth of electron avalanche are early accomplished. From the analysis of Weibull distribution, it was confirmed that as the allowed breakdown probability was given by 0.1[%], the applied field value needed to be under 21.5[kV/mm].

Digital 방사선투과검사 시스템인 1차원 Radiometric scanning system을 개발하여 부식 및 침적물이 있는 배관의 두께평가에 적용하였다. 단일 방사성 동위원소에서 나오는 방사선을 선현으로 접속하여 시험체를 투과시킨 방사선을 BGO 검출기를 사용하여 측정하는 single source - single detector alignment system과 제어 프로그램을 개발하였다. 개발된 시스템의 성능을 GEANT4 프로그램을 사용하여 예측하였다. 그리고, 인공결함을 제작하여 넣은 시편과 두께 변화를 준 시편에 적용하여 실제 성능을 평가하였다. 방사성 동위원소를 이용하여 배관의 부식과 침적물에 의한 두께 변화에 대하여 실시간으로 필름을 사용하지 않고 평가할 수 있음을 확인하였다.

In this paper, we present a design and experiment study of high power large diameter backward wave oscillator. Analysis is made within the scope of linear theory of absolute instibility. The Electron beam generator may be atteractive source of high power millimeter microwaves which has simpler structure.