We synthesized polypyrrole (PPy) nanotubules by oxidative polymerization of the pyrrole monomer on the pore of a polycarbonate membrane. The electrochemical behavior was investigated using cyclic voltammetry and AC impedance. The redox potential was about -0.5 V vs. Ag/AgCl reference electrode, while the potential was about 0 V for electro-synthesized PPy film. It is considered as the backbone grows according to the pore wall. Therefore, it is possible to be arranged regularly. That leads to improvement in the electron hopping. The AC impedance plot gave a hint of betterment of mass transport. PPy nanotubules have improved in mass transport, or diffusion. That is because the diffusion occurs through a thin pore wall of PPy nanotubules. The kinetic parameter of PPy nanotubules enzyme electrode with glucose solution was evaluated. The formal Michaelis constant and maximum current calculated by computer were about 23.8 mmol $dm^{-3}$ and $440\;{\mu}A$ respectively. Obviously, an affinity for the substrate and current response of the PPy nanotubules enzyme electrode are rather good, comparing with that of PPy film. What is more, the enzyme electrode is sensitive to blood sugar of a diabetic serum despite an obstruction of ascorbic acid, oxygen, some protein and/or hormone.

We give pressure stimulation into organic thin films and then manufacture a device under the accumulation condition that the state surface pressure is 30[mN/m]. LB layers of Arac. acid deposited by LB method were deposited onto slide glass as Y-type film. The physicochemical properties of the LB films were examined by UV absorption spectrum, SEM and AFM. The structure of manufactured device is Au/arachidic acid/Al. the number of accumulated layers are 3~9. Also. we then examined of the MIM device by means of I-V. The I-V characteristic of the device is measured from -3 to +3[V]. The insulation property of a thin film is better as the distance between electrodes is larger.

A new possibility of our atmospheric cold plasma torch has been examined on the surface treatment of an air-exposed vulcanized rubber compound. The plasma treatment effect was evaluated by the bondability with another rubber compound using a polyurethane adhesive.

Spinel $LiMn_{2-y}Mn_{y}O_4$ powder was prepared solid-state method by calcining the mixture of $LiOH{\cdot}H_2O$, $MnO_2$ and MgO at $800^{\circ}C$ for 36h. To investigate the effect of temperature for cycle behaviour of cathode material during cycling, charge-discharge experiments and initial impedance spectroscopy performed by the condition of the charge-discharge temperature. Initial charge-discharge capacity was gradually increased by rising charge-discharge temperature. However, capacity was suddenly decreased at high temperature during cycling. Capacity at low temperature was almost constant during cycling. It confirmed because Mn dissolution is more serious at high temperature than at low temperature.

The properties of $LiMnO_2$ was studied as a cathode active material for lithium polymer batteries. $LiMnO_2$ cathode active materials were synthesized by the reaction of $LiOH{\cdot}H_2O$ and $Mn_2O_3$ at various temperature under argon atmosphere. The powders were characterized by the X -ray diffraction. For lithium polymer battery applications, the $LiMnO_2$ cell was characterized electrochemically by charge-discharge experiments and a.c. impedance spectroscopy. And the relationship between the characteristics of powders and electrochemical properties was studied in this research. A maximum discharge capacity of 160~170 mAh/g for o-$LiMnO_2$ cell was achieved. The capacity of o-$LiMnO_2$ electrode demonstrated better than of the spinel $LiMnO_2$ by solid-state reaction.

We fabricated organic electroluminescent(EL) devices with mixed emitting layer of poly(N-vinylcarbazole)(PVK), 2,5-bis(5'-tert-butyl-2-benzoxazoly)thiophene(BBOT), N,N'-diphenyl-N,N'-(3-methyphenyl)-1,1'-biphenyl-4, 4'-diarnine(TPD) and poly(3-hexylthiophene)(P3HT). To improve the external quantum efficiency of EL devices, we added the functional layer to the devices such as LiF insulating layer, carrier confinement layer(BBOT) and hole injection layer(CuPc). In the ITO/emitting layer/Al device, the maximum quantum efficiency at 15V was $1.88{\times}10^{-5}%$. And then, it is increased by a factor of 27 to $5.2{\times}10^{-3}%$ in ITO/CuPc/emitting layer/BBOT/LiF/Al device at 15V.

we have quantitatively investigated the possibility of feeding oxygen radical in air environment. The oxygen radical generation from the plasma was verified and its efficiency was found to be dependent on the cathode material by the analysis with optical emission spectroscopy as well as by the quartz crystal micro-balance method.

The Al etching was studied employing negative ions generated in the downstream $Cl_2$ plasma. In order to etch the Al film practically on an insulator covered electrode coupled with RF power, reduction of the negative self bias voltage (Vdc) was examined using a magnetic filter which trapped electrons. Addition of $SF_6$ and $H_2$ to a $Cl_2/BCl_3$ mixture reduced significantly Vdc.

To observe the Langmuir films, displacement current measuring system(Nippon Laser & Electronics), $\pi-A$ isotherms measuring device, and Brewster Angle Microscope(BAM) were used. As results, for 8A5H, big tilt angle changes of many molecules were detected before liquid expanded phase when the monolayer was compressed and expanded by barrier. Also many small and bright points were detected by BAM when the displacement current radically changed. In $\pi$-A isotherms, surface pressure of 8A5H was radically decreased between 35 and 40[mN/m] and monolayer was assumed to be collapsed in solid condensed phase, since large bright domain was observed without change of displacement current and this bright boundary was not classified part of domain in BAM image. If we observe behaviors of molecules on the water surface in these three measurement at the same time, we can get more precise informations on L films and it could be good data for fabricating LB films.

The ZnO devices using semiconductor properties, to include $MnO_2$, $Y_2O_3$ and other material, was fabricated by $Sb_2O_3$ mol ratio from 1 to 4 [mol%]. The non-linearity factor was calculated by setting current to be $1[mA/cm^2]$ and $10[mA/cm^2]$. The spinel structure was fonned by $Sb_2O_3$ addition and it was depressed the ZnO grain formation. The grain growing was controlled by spinel structure that has improved the non-linearity factors. The breakdown voltage characteristics of semiconductor devices to increase with $Sb_2O_3$ was increased in voltage-current. The non-linearity value of ZnO semiconductor devices was 45 over.

The structural properties of varistors surface studied by fractal phenomenon were investigated to verify the relations of electrical characteristics. The SEM photograph of varistors surface were changed by binary code and the grain shape of that were analyzed by fractal dimension. The void of varistors surface was found by fractal program. The relation between grain density and electrical properties depend on fractal dimension. The grain size in varistors surface was decreased by increasing of oxide antimony addition. The grain size of devices by oxide antimony addition were from 5 to $10[{\mu}m]$. The fractal dimension and electrical properties of varistors surface was related to between grain boundary and grain density. The grain size was decreased by increasing of fractal dimensions.

The Breakdown electric field of ZnO semiconductor devices in voltage-current characteristics was increased by increasing of additive materials. The specimen that has not additive materials was not formed spinel structure. The critical voltage that has not spinel structure was 235[V]. When the additive materials has 0.5 and 2[mol%], the Breakdown electric field was 840 and 758[V] in each additive materials. The Breakdown electric field of varistors as a factor of voltage and current was increased by addition of oxide antimony. The varistors that has oxide antimony was linearly increased in low electric field.

The characterization of organic Metal/Insulator/Metal(MIM) devices were investigated from LB films. The physicochemical properties of the LB films were by UV absorption spectrum and AFM. We give pressure stimulation into organic thin films and then manufacture a device under the accumulation condition that the state surface pressure is 2, 10, 30[mN/ml The stable images are probably due to a strong interaction between the monolayer film and glass substrate. We are unable to obtain molecule resolution in images of the films but did see a marked contrast between images of the bare substrate and those with the network structure film deposited onto it.

The conventional tracking testing as IEC-60587 is widely used in surface aging measurement of outdoor insulator because those testing can carry out very short time in Lab-testing. Also IEC-60587 testing is able to offer the standard judgement of relative degradation level of outdoor HV machine/system. Therefore it is very useful method compare to previous conventional tracking testing method and effective Lab-testing method. But surface discharges(SD) have very complex characteristics of discharge pattern so it is required estimation research to development of precise analysis method. In recent, the study of IRR-camera is carrying out discover of temperature of power equipment through condition diagnosis and system development of degradation diagnosis. In this study, SD occurred from procelain insulator, used 22.9[KV] distribution, is measured with partial temperature distribution in real time, the degradation grade of SD is analyzed through produced patterns in SD concentration according to applied time.

The partial discharge testing is widely used in diagnostic measuring technology because it gives low stress to power equipment which is undertaken tests. Therefore it is very useful method compare to previous destructive methods and effective diagnosis method in power system that requires on-line/on-site diagnosis. But partial discharges have very complex characteristics of discharge pattern, so it is required continuous research to development of precise analysis method. In recent, the study of partial discharge is carrying out discover of initial defect of power equipment through condition diagnosis and system development of degradation diagnosis using HFPD(High Frequency Partial Discharge) detection. In this study, simulated system is manufactured and HFPD occurred from those simulator is measured with broad-band antenna in real time, the degradation grade of system is analyzed through produced patterns in simulated target according to the AI/statistics processing.