The Characteristics of Digital Vterbi Decoder utilizing the analog parallel processing circuit technology is proposed. The Analog parallel structure of the viterbi decoder acted by a replacement of the conventional digital viterbi Decoder is progressing fastly. The proposed circuits design han, low distortion, high accuracy over the previous implementation and dynamic programming.

Multi Cultivation Remote-control System(MCRS) for crops through characteristics of multi-safe sensors was realized. It was carried out to investigate into the effect of LED Control with the physiological activity of crops(for examples, sprouts). We have also composed a Combined Automatic Control System possible for the control of temperature and humidity at the same time. And we producted the remote control as using Linux.

The depth of the object pointed by the laser beam is computed depending on the pixel position on the CCD There involved several number of internal and external parameters such as inter-pixel distance, focal length, position and orientation of the system components in the depth measurement error. In this paper, it is shown through the error sensitivity analysis of the parameters that the most important parameters in the sense of error sources are the angle of the laser beam and the inter pixel distance. Also, the calibration technique to minimize their effect for the depth computation is proposed.

The $Sr_{0.7}Bi_{2.3}Nb_2O_9$(SBN) thin films are deposited on Pt-coated electrode (Pt/Ti/$SiO_2$/Si) using RF sputtering method at various deposition temperature. The crystallinity of SBN thin films were increased with increase of deposition temperature in the temperature range of 100~400[$^{\circ}C$]. The surface roughness of deposition temperature($300^{\circ}C$) showed about 4.33[nm]. The grain and crystallinity of SBN thin films were increased with the increase of annealing temperature.

The SBN thin films were deposited at substrate temperature of 300[$^{\circ}C$] on Pt-coated electrode (Pt/Ti/$SiO_2$/Si(100)) using RF sputtering method. The grain and crystallinity of SBN thin films were increased with the increase of annealing temperature. The dielectric constant(150) of SBN thin film was obtained by annealing temperature above 750[$^{\circ}C$]. The frequency dependence of dielectric loss showed a value within 0.03 in frequency ranges of 1~1000[kHz].

In this paper, the limiting characteristics of the fault current in a power system with a superconducting fault current limiter(SFCL) applied into neutral line of main transformer in a distribution power line were analyzed. The SFCL applied into the neutral line of main transformer power system can limit the unsymmetrical fault current from the single-line ground fault or the double-line ground fault. In addition, it could be decreased a number of SFCL and a load. This method could be expected to reduction of a power loss in the neutral line, because of a neutral line current is zero in ordinary times.

The proton exchange membrane fuel cell (PEMFC) holds great promise of clean power. However, in practical applications which use the PEMFC as the power source, the output voltage from the fuel cell undergoes transient response especially during acceleration and deceleration. This paper presents the relationships between the internal voltage drop, voltage of time constant, time constant of FC1 and FC2 (in series and in parallel) charge curves and discharge curves respectively.

The solar cell energy is considered as a clean energy source in the world. However, because the output of solar cell is not constant, it needs to study the relationships of the DC voltage, the DC current and the DC power of the solar cell. This paper presents the solar cell output characteristics and the maximum power point of the solar cell under different irradiation conditions.

Recently, annual usage of energy is dramatically increasing by industrialization is going faster and more electricity is needed due to various electronic devices. This paper present relationships between the Vmax, $V_T$, load and time constant of solar cell charge and discharge curve. Charging and discharging recording where the external resistance will become larger Vmax, $V_T$ is decrease and the time increases and decreases there is a possibility of knowing.

The hall probe measurement system was used to measure the critical current distribution of superconducting coated conductor. The system consists of reel to reel moving apparatus, 7 array hall probe, a rotary encoder and permanent magnet. The magnetic field profile across the width of superconducting coated conductor using Bean's critical state model was calculated. The effect of various parameters of the formulas on the magnetic field distribution and the effect of shape and size of artificial defects, which were formed on the surface of SmBa2Cu3O7-d(SmBCO) coated conductor using laser marking system, on the hall probe magnetic field signal of the hall probe measurement system was investigated.

Piezoelectric sensors are extensively used to measure force because of their high sensitivity and low cost. however, the development of device with reduced size but with improved sensitivity is highly important. Low-temperature co-fired ceramic (LTCC) is one of promising materials for this application than a silicon substrate because it has very good electrical and mechanical properties as well as possibility of making various three dimensional (3D) structures. In this work, piezoelectric pressure sensors based on hybrid LTCC technology were presented. The LTCC diaphragms with thickness of $400\;{\mu}m$ were fabricated by laminating 12 green tapes which consist of alumina and glass particle in an organic binder. The piezoelectric sensing layer consists of PZT thin film deposited by RF magnetron sputtering method on between top and bottom Au electrodes. The PZT films deposited on LTCC diaphragms were successfully grown and were analyzed by using X-ray diffraction method (XRD) and field emission scanning electron microscope (FESEM).

Recently, low temperature co-fired ceramic (LTCC) technology has gained a remarkable application potential in sensors, actuators and micro systems fields because of its very good electrical and mechanical properties, high reliability and stability as well as possibility of making 3D micro structures. In this study, we investigated the effects of annealing treatment on the electrical properties of $Pb(ZrTi)O_3$ (PZT) thin films deposited on LTCC substrate. PZT thin films were deposited on Au / LTCC substrates by RF magnetron sputtering method. Then, the change of the crystallization of the films were investigated under various annealing temperatures and times. The results showed that the crystallization of the films were enhanced as increasing annealing temperatures. The film, annealed at $700^{\circ}C$, 3min, was well crystallized in the perovskite structure.

We used Brewster's Law to examine the mechanism of liquid crystal (LC) alignment on an organic insulation layer when subjected to ion-beam irradiation. Brewster's Law implies that the maximum rate polarized rayon a slanted insulation layers on the substrate and it illustrates the dependence of polarization and themechanical structure on the ion beam irradiation process. The pretilt angle of nematic LCs on the organic insulation surface was about $1.13^{\circ}$ for an ion beam exposure of $45^{\circ}$ for 1 minute at 1800eV. This shows the dependence of LC alignment on the polarization ratio in a slanted organic insulation layer. We also discussed the electro-optical characteristic of twisted nematic (TN) LCD using ion beam irradiation on organic overcoat layer.

Polycrystalline $CuInS_2$ thin films were performed from S/In/Cu Stacked elemental layer(SEL) method with post annealing. In thin method, the thin films were annealed in Vacuum of $10^{-3}$ torr or in S ambient. $CuInS_2$ thin films were manufctured by using the evaporation and the annealing with vacuum quartz furnace of sulfurization process was used in the vacuum chamber to the substrate temperature on the glass substrate the annealing temperature and characteristics thereof were investigated. The physical properties of the thin film were investigated under various fabrication conditions including the substrate temperature annealing time by XRD, FE-SEM, and Hall measurement system.

최근 PCA 아크튜브를 사용한 세라믹 메탈핼라이드 램프가 개발되어 기존의 석영관 메탈핼라이드 램프의 사용 범위를 넘어 다양하게 활용되고 있다. 이에 따라 램프의 신뢰성 또한 중요한 요소로 여겨지게 됨으로 본 논문에서는 세라믹 메달핼라이드 램프의 아크튜브의 열화특성을 확인하기기 위해 램프를 가속열화 시켜 구조적 변화를 확인하였다. 이 결과 모세 관 내 Moly winding과 세라믹 아크튜브의 열팽창계수 차이로 인해 간격이 멀어지고 그 사이로 원소들이 침입하였고 이로 인해 아크튜브와 전극의 열화를 촉진하며 전극의 틀어짐을 유발하였다. 또 내부에 봉입된 희토류 금속 요오드화물이 고온에서 PCA 관벽과 반응을 일으켜 아크튜브를 부식시킴을 확인할 수 있었다.

We suggest CNT-based gas sensors for breath alcohol measurement. The sensors were composed of single-walled carbon nanotubes (SWNTs) thin film on glass substrate with simple process, and the SWNTs thin film as sensing layer was formed by multiple spray-coating with SWNT composites which was well-dispersed, highly controlled and differently functionalized by various binders (TEOS, MTMS, and VTMS) added in ethanol solvent. In this work, three different SWNTs thin films were made to compare their electrical response properties for alcohol vapor. From fabricated sensors, conductance responses were measured and discussed. In the result, our alcohol gas sensors showed an effective selectivity even at room temperature.

We present a simple process for the fabrication of high performance transparent conducting films that contain single-walled carbon nanotubes (SWCNTs) noncovalently coated with an ultrathin titania layer. The hydrophobic interactions between nanotube surfaces and the acetylacetone (acac) ligands used to stabilize the $TiO_2$ precursor provide an interesting alternative method for noncovalently coating the SWCNTs with a titania layer. The ultrathin titania layer on SWCNTs prevented the oxidation of functionalized SWCNTs at high temperatures, and protected against water molecule absorption.

현재 시대에는 자원의 부족으로 인하여 원재료의 낮은 등급을 정제하는 것이 중요하다. 자기분리 기술이 산업 계 원재료들의 정제에 적용되는 것이 기대된다. 예를 들면 고순도의 유리나 절연체를 제작하기 위한 원재료에서 철산화물의 제거는 매우 중요하다. 자기를 띠는 입자들과 자기분리 필터 와이어 사이에 발생하는 끌어당기는 힘은 다른 자기분리와 비교 할 때 초전도 자기분리에서 훨씬 강하다. 초전도 마그네트를 이용하여 높은 자기장을 형성하기 때문에 일반 자기분리의 자성 입자 포획력을 능가한다. 본 연구에서는 습식 조건에서 산업계 원재료로부터 철계 산화물을 제거하기 위해서 초전도 자기문리를 사용하여 실험하였다. 실험에 사용된 시료는 유리원료로 사용되는 2종류로 시료A는 0.1 ~ 0.3 mm의 평균입도를 갖는 모래형상이며 시료B는 평균입도 0.03 ~ 0.1 mm의 고운모래 형태이다. 자기분리를 위해 상온에서 100 mm의 직경을 갖는 600 mm의 높이의 전도냉각형 Nb-Ti 초전도 마그네트를 사용하였으며 시료를 위에서 공급하고 아래로 배출되도록 수직형으로 설치하였다. 시료 500 g과 증류수 2 L를 혼합하여 교반시키고 6 T의 자기장 하에서 실험하였다. 자기분리 필터는 초전도 마그네트에서의 자기장의 분포를 해석하여 디자인하였다. 자기분리 필터의 자기적 특성을 알아보기 위해 진동시료형 자력계를 사용하였다. 산업계 원재료는 X선 형광분석기를 사용하여 성분을 분석하였다. 산업계 원재료를 이용하여 초전도 자기분리를 실시한 결과 철계 산화물은 시료A에서 43.5 %제거되었으며 시료B에서는 77.3%제거되었다.

협소한 지역, 고호율의 에너지 변환을 할 수 있는 MW급 Dish-Stirling 태양열발전 연구는 관련기술 개발뿐만 아니라 마이크로그리드 더 나아가서는 스마트그리드 사업의 안정적 유지에 도움을 준다. 태양열 발전 시스템은 태양열 발전기설계를 포함한 발전 송배전계통 연계의 원천기술확보와 함께 모니터링 등의 기술 분야에 있어서 상용화가 가능하다.

Because of power consumption increase, global warming, and limitation of installation, not only high reliability and interruption capability but also compact and light power apparatuses are needed. In this paper, various models that short and long gap distance were used to analyze E field of each model. Calculation value was estimated of flashover position. As a result, short and long gap distance that vacuum interrupter inner between move electrode and fix electrode not coincided flashover position of each model. short gap distance estimated flashover position at electrode edge. but long gap distance model confirmed $E_{max}$ value at center shield. in this paper was compared electric field value. and estimated of flashover position from electric field calculation.

In this paper, we analyzed the frequency spectrum of electromagnetic waves which is generated by series arc discharges to develop a condition monitoring technique in a closed-distribution board. We fabricated an arc generator specified in UL1699 to simulate series arc discharge. The experiment was carried out in an electromagnetic shielding room, and the measurement system consists of a Ultra Log Antenna and a EMI Test Receiver. The results showed that the frequency spectrum during series arc discharges was distributed in ranges of 30~500 [MHz], and the peak values were existed at 40 [Mhz] and 80 [MHz].

This paper describes the design and fabrication of a Risk Voltage Meter (RVM) which can analyze the step and touch voltages in grounding systems. The meter consists of a sine-wave power source which generates up to 300 [$V_{rms}$] in ranges of 45 [Hz]~1 [kHz], a 8 Ch. data acquisition module, and a personal computer. Also, a noise elimination method by a digital band-pass filter during measurement is proposed.

Line to ground faults or lightning strikes in electrical power systems produce high frequency overvoltages. With this reason, a wide band analysis of the ground impedance is necessary. In the paper, design of a wideband ground impedance meter which can measure the ground impedance in ranges from 65 Hz to 1.5 MHz is described. Also, a noise elimination method by a digital band-pass filter during measurement is proposed. The maximum measurement error of the meter is estimated 3 % in full ranges.

The exact partial discharge pulse should be measured in order to estimate the discharge source in the solid insulation and diagnose the degree of deterioration. Partial discharges generated in the insulation occur in the internal voids or at the edge of the insulation, have unique characteristics following the type and location. When external voltage is applied, Partial discharges occurred in the restrictively presented voids increase the quantity of electrical charge at the discharge onset voltage. The discharge characteristics have remained constant as space is filled by the impurity such as a compound of gases accompanied with discharge. In this study, How to design the insulation about the problems of the built-in diagnostics in the transformer is discussed by the interpretation of electric field.

The higher the short circuit currents, the faster the interruption takes place. For increasing the interrupting performance of the MCCB, it is important to design optimally the adjustable tripping device, the open /shut mechanism, and the arc quenching room in the MCCB. This paper is focused on understanding the interrupting performance, more specifically of the grid and the fix contact, based on the shape of the arc quenching room in the current MCCB.

Surface contamination and leakage current have caused operating problems. A flashover in a substation may result in destruction of an insulator or many others electrical equipment. Engineering plastics have good characteristic (light weight, good productivity and little of void) as compare with epoxy or porcelain insulators. Outdoor insulator must have resistance to contamination. However, it isn't suited to outdoor insulator because it is not hydrophobic. RTV(Room temperature vulcanizing) has a good property of hydrophobic and micro-filler. nano-filler have characteristics of obstructing exothermic reaction. In order to reduce the incidence of insulator flashover and damage, the silicon rubber contained with micro, nano-filler coating on surface of engineering plastics. In this paper, it compares tracking resistance, leakage current of the engineering plastic coated RTV with that of non-coated engineering plastic. And filled-composites performed much better than non-filled composites.

In order to prepare a epoxy/multilayered silicate nanocomposite, various mixing processes were tried and it was found that the silicate could not be fully exfoliated in the epoxy matrix through various mechanical mixing process. In this study, a new AC electric application method was developed to prepare epoxy/multilayered silicate nanocomposite. The exfoliation of the silicate was confirmed by XRD (X-Ray Diffraction) and TEM observation.

Nano particles (10nm $SiO_2$) were silane-treated in order to modify the surface characteristics in a epoxy nanocomposite. Then, micro particles ($3{\mu}m$ SiO2) were poured into the epoxy nanocomposite using various mixing process and epoxy/micro-and-nanomixed composites (EMNC) were prepared. The thermal (Tg) and mechanical (tensile and flexural strength) properties were measured by DSC, DMA and UTM and the data was estimated by Weibull plot.

A epoxy/multilayered silicate nanocomposite was prepared by a new AC electric application method and micro silica particle was poured into the nanocomposite in order to prepare epoxy/micro-and-nano- mixed composites (EMNC). Electric insulation breakdown strength was measured in a sphere-sphere electrode system designed for the prevention of edge breakdown and the data were estimated by Weibull plot. As the exfoliated silicate nano-plates were homogeniously dispersed in the micro silica particles, the insulation property was higherd.

최근 개발된 식물성 절연유는 광유에 비해 약 3배 정도 점도가 높아 변압기 냉각에 상당한 영향을 주게 된다. 뿐만 아니라 식물유의 유동점은 $-20^{\circ}C$이하로 광유에 비해 높은 것이 단점이다. 온도가 낮을수록 점도가 급격히 높아질 뿐만 아니라 유동점에 도달할수록 응고되어 가기 때문에 겨울철에 변압기 부하가 낮거나, 교체 운전 초기에 냉각 특성 및 전기적 특성의 변화를 가져올 수 있다. 이에 따라 식물성 절연유를 유동점에 가까운 온도로 냉각한 후 절연파괴전압을 측정하였다.

This paper describes effect of the bending deformation of high voltage composite bushing with winding tension. The composite bushing can be formed, by adding silicone rubber sheds to a tube of composite materials. The FRP tube is internal insulating part of a composite bushing and is designed to ensure the mechanical characteristics. Generally the properties of FRP tube can be influenced by the winding angle, wall thickness and winding tension. As winding tension is increased glass contents was increased in the range of 70.4~76.6%. In the bending test, winding tension is increased residual deflection was decreased in the range of 14.0~12.2 mm.

This paper illustrates the use of electric field computation to optimize the design of high voltage composite bushing. In the bushing, a high electric stress occurred between field shaper and central conductor by the closely space. Also coaxial cylindrical shield has a great height along the axis to control an electric field. Consequently, all the potentials are raised axially along the field shaper and electric stress is concentrated on a part of the surface of the FRP tube near the upper end of the field shaper. Maxwell 2D simulator based on the boundary element method was also introduced in order to verify the reliability of the polymer bushing. The optimized design uses internal elements for electric stress grading at critical parts of the bushing.

송전 및 배전계통에 운영되고 있는 유입식 변압기는, 생분해성이 좋아 보다 더 친환경적인 식물성 절연유로 대체되어 가고 있으며, 미국등지에서는 이미 10여년 전부터 식물성 절연유를 사용한 변압기를 배전 및 송전 계통에 사용하고 있다. 본 연구에서는 기존의 광유계 절연유를 대체하는 식물성 절연유를 사용한 배전급 변압기 및 기존의 광유계 절연유를 사용하는 동일한 용량의 배전급 변압기($1_{\phi}2010KVA$ 13200-230V)를 제작하여 열사이를 형태의 복합 열화를 시켜, 식물유 및 광유를 채취 분석하고 그 열화 기구를 연구하였다.

In these days $SF_6$ mixtures and alternative gas has been studied because of global warming. so although many studies have been carried out about binary gas mixtures with $SF_6$, few studies were presented about breakdown characteristics of $SF_6/N_2$ mixtures. In this paper, breakdown experiment values and breakdown simulation value are compared. Streamer theory was used for predicting breakdown voltage. For accurate simulation, this simulation apply utilization factor using CST program. AC breakdown experiments in non-uniform field was performed to compare with the breakdown simulation values. But with gap lengths increasing, the breakdown voltage is saturated. So simulation need surface roughness factor.

대전력 마이크로파를 발생시키는 장치로서 축방향의 전자빔을 이용한 장치가있는데 현재 고주파수와 고효율을 목표로하여 연구하였다. 이에 대한 해석에 대하여 전자파 발진에 관한 상호작용의 기온 특성에 대하여 슬로우 사이크로트론 상호작용에 대하여 연구한 결과를 나타내어 해석하였다.

낮은 에너지를 이용하여 상대론적 영역에서 동작하는 마이크로파 출력장치를 연구하였다 그에 따른 후진파 발진기는 대전력 마이크로파를 발생시키는 장치로서 연구하였으며 관내에 전자빔을 입사시킴으로서 발진이 일어나 출력을 발생 시킨다.

CdSe nanocrystals (NCs) have been decorated on singlewalled carbon nanotubes (SWCNTs) by combining a method of chemically modified substrate along with gate-bias control. CdSe/ZnS core/shell quantum dots were negatively charged by adding mercaptoacetic acid (MAA). The silicon oxide substrate was decorated by octadecyltrichlorosilane (OTS) and converted to hydrophobic surface. The negatively charged CdSe NCs were adsorbed on the SWCNT surface by applying the negative gate bias. The selective adsorption of CdSe quantum dots on SWCNTs was confirmed by confocal laser scanning microscope. The measured photocurrent clearly demonstrates that CdSe NCs decorated SWCNT can be used for photodetector and solar cell that are operable over a wide range of wavelengths.

We present facile chemical route stabilizing dispersion of carboxylated single-walled carbon nanotubes (SWCNTs) in ZnOsol prepared by using diethanolamine as a stabilizer. The dispersion was stabilized via capping of carboxyl groups on the SWCNT surface by a titania layer. We also demonstrated that the conductivity of the films prepared P3/$TiO_2$/ZnO as enhanced by therml treatment, and thethermal stbility of the film improved hybridization with ZnO sol pristine P3, P3/$SiO_2$ and P3/$TiO_2$ hybrid films.

We have characterized the previously undescribed parameters for engineering the electrical properties of single-walled carbon nanotube (SWCNT) films for technological applications. The surface tension of the top coating passivation material and matching coefficients of thermal expansion for the substrate and carbon nanotube network are two crucial parameters for the fabrication of reliable and highly conductive single-walled carbon nanotube network thin films.

we have investigated the field emission characteristics of the CNT/TEOS hybrid thin films fabricated by a spray method. It is found that the CNT/TEOS hybrid emitters show high current density, low turn on field, and long-term emission stability compared to the CNT emitters. These efficient field emission characteristics of the CNT/TEOS hybrid emitters are attributed to the TEOS sol, acting as a protection layer of nanotube emitter by surrounding the nanotube tip as well as a binder material to enhance the adhesion of nanotube emitters to the substrate. Therefore, the CNT/TEOS hybrid emitters could be utilized as an alternative for the efficient and reliable field emitters.

냉방기기의 고성능소형화를 촉진시키기 위해서는 고강도 고열전도성 알루미늄합금소재의 개발이 시급하다. Condenser용 튜브부품은 향후 더욱 소형화, 경량화 하는 방향으로 전개되며, 결국 목표로 하는 컨덴서용 튜브 소재적인 측면에서의 기능은 고강도, 고열전도, 압출성이 우수하여야 한다.

Nanoporous anodic alumina membranes (NAAM) with high aspect ratio, self-ordered pore array were fabricated by high-field 2-step anodization method. High voltages of 80, 100, 120 and 140 V as well as 40 V for comparison were applied to an aluminum anode with respect to a Pt cathode immersed both in 0.3M oxalic acid solution in order to investigate the self-ordering characteristics of the nanoporous structure. The pore structures, including interpore distance, pore size, pore density, and porosity as well as the ordering characteristic were analyzed using field-enhanced scanning electron microscopy (FE-SEM) and the corresponding Fourier-transformed images. The nanoporous structure could be produced for all the voltage conditions, but the well-ordered through-hole pore without a branched structure seemed to occur only at 40 and 140 V. It turned out that the growth rate under 140 V high-field anodization was about 40 times higher than under conventional 40 V mild anodization, which enabled the fast fabrication of self-ordered, high aspect ratio NAAMs.

In order to detect exact corona discharge point at stator winding of a rotating machine, an inductively coupled magnetic probe has been developed, which consists of U-shaped and truncated manganese ferrite inductor as a helix. The measured current intensity is somewhat higher than commercially developed probe. It has been shown that the measured intensity of proposed probe is suitable for manual localization as to off-line stator winding monitoring of rotating machine.