The spheroidization of cold rolled lamellar pearlite in annealing at the temperatures between 600 and $700^{\circ}C$ has been studied by quantitative micrography. It was foud that the spheroidization proceeded as two stageh. The first stage was the stage of relieving the stored energy by cold work, the second was the stage of reducing the interface energy between ferrite and cementite. The spheroidization rate combining the spheroidization rate of each stages is described by the following equation : $$d(1/S)/dt=k_3{\cdot}D/_{(1/s)}\{{\sigma}V/_{(1/s)}+k_4{\cdot}{\exp}(-bt)\}$$ Where, S is the total area of the interface between ferrite and cementite per unit volume, D is the diffusion coefficient, ${\sigma}$ is the boundary energy, V is the volume fraction of the cementite, and $k_3$, $k_4$, b are constants.

Among the many maunfactured processes of producing multi filamentary composites, in situ process is widely used owing tv its simplicity and easyness of mass production. In this study, the mechanical and electromagnetic properties of Cu-Fe composite materials was investigated. The tensile strength of the Cu-Fe wires increased as the Fe content and reduction ratio were increased. The Cu-30 wt%Fe composites had the best properties in terms of figure merits compared to the other Cu-Fe composites made in this study or the commercially manufactured 6/1 ACSR cables of Cu cable. The coercivity was decreased by increasing Fe content, but the squareness was increased greatly. As increasing reduction ratio, the coercivity and squareness increased up to the maximum points, and then decreased. For example, the maximum values were obtained at $0.09mm{\phi}$ for Cu-30 wt%Fe composites and at $0.066mm{\phi}$ for Cu-45 wt%Fe composites. The magnetic property of Cu-Fe wires produced by precipitation treatment was higher than that of Cu-Fe wires produced by thermomechanical treatment. By annealing Cu-Fe wires after drawing process, the coercivity, remanence and squareness were improved.

강의 내마모성과 내식성을 증가시키기 위하여 종래의 방법보다 우수한 확산표면경화처리에 대하여 연구하였다. 무수붕사($Na_2B_4O_7$)를 주체로 하는 해당염욕에 첨가물로서 -100 mesh의 Fe-V를 첨가한 후 각각 탄소량을 달리하는 시편을 침적시켜 탄화물층의 형성유무와 탄화물층과 침척시간과의 관계 및 피처리재중의 탄소량과의 관계에 대하여 조사하였고, 탄화물층내의 미소경도를 측정하였다. 연구결과는 다음과 같다. (1) 탄화물층은 모재표면의 C원자와 붕사욕 중에 용출된 V와 결합에 의해서 형성되고 형성된 탄화물층 속으로 확산해서 모재 중의 C원자가 표면에 보급되는 것에 의해서 성장한다. (2) 탄화물층의 두께는 온도와 탄소량이 일정할 경우 침척시간의 1/2 승에 비례하였다. 또한 온도와 침적시간이 일정할 경우 탄소량이 증가할수록 탄화물층의 두께는 증가하였다. (3) 시편의 표면에 형성된 탄화물층은 VC층이었으며, 이 탄화물층 내의 미소경도는 $H_v$ 3,000 이상이다.

The adhesion strength of TiN films to substrate(STC 3) steel has been studied using the scratch adhesion test. Before deposition, the substrates were mechanically polished and TiN films were deposited at different substrate temperature($480^{\circ}C-540^{\circ}C$). The chemical properties of TiN films were investigated by RBS, and EDS, and the physical properties were investigated by micro-hardness tester, SEM, and X-ray diffractometer. According to results of this study, the adhesion strength of TiN films increase with increasing the deposition temperature. The roughness of the polished substrates surface were measured with a profilometer. It was observed that, as a general rule, the adhesion strength of deposited TiN films increase with decreasing the substrates surface roughness.

Effects of aging treatment on the microstructures and microhardness of a rapidly solidified Al-Li-Cu-Mg-Zr alloy were investigated by differential scanning calorimetry(DSC) and transmission electron microscopy(TEM). The as-melt-spun ribbon was consisted of fine ${\delta}^{\prime}$ and icosahedral intermetallic compound which were precipitated in the matrix. Two exothermic peaks with the range of $120^{\circ}C-190^{\circ}C$ and $280^{\circ}C-344^{\circ}C$ corresponded to ${\delta}^{\prime}$ and ${\theta}^{\prime}$, S', $T_1$ precipitating reaction respectively, and two endothermic peaks with the range of $190^{\circ}C-280^{\circ}C$ and $344^{\circ}C-550^{\circ}C$ corresponded to dissolution of ${\delta}^{\prime}$ and ${\theta}^{\prime}$, S', $T_1$ respectively in DSC curves. Peak hardness value was obtained at $210^{\circ}C$ for 1 hr aging treatment.

Recrystallization behaviors of ordered and disordered structures in $Ll_2$ type $Ni_3Fe$ alloy were studied through hardness measurement and differential thermal analysis. When the disordered structure was isothermally aged at $480^{\circ}C$ below order-disorder transition temperature, the hardness of the structure was increased due to progressive ordering with increasing aging time. The hardness of the disordered structure was increased rapidly with increasing deformation degree up to 10%, and then gradually increased with further deformation degree. while the hardness of the ordered structure was increased rapidly with increasing deformation degree up to 10%, showing a constant hardness value up to 50% and gradually decreased with further deformation degree. The hardness of the ordered structure was higher than that of the disordered structure at all same deformation degrees. The recrystallization temperature of the ordered and disordered structures were decreased with increasing deformation degree. At the same deformation degrees, the recrystallization temperature of the ordered structure was lower than that of the desordered structure.