This paper is to investigate the characteristics of debris flow landslides in Gangwon Province through literature review, data collection and analyses and site investigation. As results of data analyses about landslides occurred currently in this province, the landslide in the form of debris flow is found to be 55 %. Therefore major loss and costs are caused by discharge of soil and rock fragments from landslide. From results of analyzing the geometrical characteristics of landslide, length of most of landslide is less than 200 m, their width is in the range of 10 - 40 m, most of them are know to be occurred in lower elevation than 400 m. Slope angle is in the range of 25 - 35 degrees. Comparing the period of rainfall intensity with the time of landslide being occurred, occurrence of landslide is quite related to duration of a heavy rainfall. For measures of controlling water flow discharge and debris flow, considering geological and topographical ground conditions, appropriate selection and building check dam, erosion control dam and ring net is very beneficial for reducing the loss and costs caused by the landslide of debris flow.

Applicability of hyperbolic settlement prediction method to consolidation settlement in the dredged and reclaimed ground was assessed by analyzing results of centrifuge tests modelling self-weight consolidation of soft marine clay. From literature review about self-weight consolidation of soft marine clays located in southern coast in Korea, constitutive relationships of void ratio - effective stress - permeability and typical self-weight consolidation curves with time were obtained by analyzing centrifuge model experiments. For the condition of surcharge loading, exact solution of consolidation settlement curve obtained by using Terzaghi's consolidation theory was compared with results predicted by the hyperbolic method. It was found to have its own inherent error to predict final consolidation settlement. From results of analyzing thc self-weight consolidation with time by using this method, it predicted relatively well in error range of 0.04~18% for the case of showing the linearity in the relationship between T vs T/S in the stage of consolidation degree of 60~90 %. However, it overestimated the final settlement with large errors if those relation curves were nonlinear.

In recent years, much attention has been paid to "Photocatalytic oxidation" as an alternative technique, where the pollutants are degraded by UV-irradiation in the presence of a semiconductor suspension such as titanium dioxide. $TiO_2$ is the most often used photocatalyst due to its considerable photocatalytic activity, high stability, non-environmental impact and low cost. 1n this research, the photocatalytic degradation of humic acid, acetaldehyde and methylene blue in $UV/TiO_2$ systems has been stydied. The effect of calcination temperature for manufacturing of $TiO_2$ photocatalysts and type of photocatalysts on photodegradation has been investigated. Photocatalysts with various metal ions(Mn, Fe, Cu and Pt) loading are tested to evaluate the effects of metal ions impurities on photodegradation. The photodegradation efficiency with $Pt-TiO_2$ or $Fe-TiO_2$ or $Cu-TiO_2$ is higher than Degussa P-25 powder. However, the photodegradation efficiency with $Mn-TiO_2$ is lower than Degussa P-25 powder. The photocatalytic properties of the nanocrystals were strongly dependent upon the crystallinity, particle size, standard reduction potential of various transition metal and electronegativity of various transition metal. As a result photocatalysts with various metal ion loading evaluated the effect of photodegradation.

Ozone/GAC and ozone-GAC processes were introduced for treatment of humic acid, which is representative refractory organic compound. The treatment efficiencies of humic acid in each process were analyzed in pH variation, DOC removal, and $UV_{254}$ decrease. $UV_{254}$ decrease in all processes was comparatively high with efficiency over 92%. $UV_{254}$ decrease in ozone alone process was 85%. DOC removal in Ozone-GAC process was the highest with 75%. Removal by Ozone/GAC, Ozone alone processes were 71% and 33% respectively.

The purpose of this paper is an adaptive image interpolation using parametric cubic convolution. Proposed method derive parameter of adapting the frequency from adjacent values. The parameter optimize the interpolation kernel of cubic convolution. Simulation results show that the proposed method is superior to the conventional method in terms of the subjective and objective image quality.

Recently, there are a lot of multimedia products to using image interpolation system. However, most interpolation systems in existence suffer visually to some extents the effects of blurred edges and jagged artifacts in the image. I in this paper, we propose the adaptive linear interpolation system that uses the sub-pixel. We system calculate the warped distance among the pixels of an image, and use data for Optimize length parameter. Our experimental results show that our new algorithm significantly outperforms linear interpolation in subjective quality, and in most cases, in terms of PSNR as well.

The track of high-speed railway get deteriorated according as using it. In that case, the maintenance jobs are needed for improvement of track quality. A scheduling problem for the track maintenance of high-speed railway is to determine the jobs should be performed daily. In the problem, the set of jobs for maintenance is given. Each job has it's parameters such as due date, emergency level, and processing time. In addition, jobs can be worked during a certain fixed time when the train doesn't move. In this study, we developed a mathematical model of the scheduling problem for the maintenance of high-speed railway and solved the problem using the ILOG CPLEX library.

In these days, domestic manufacturers are faced with managerial difficulties such as the increasing competition in their industry and the increasing power of customers. In this situation, they have to satisfy their customers with high quality of their products and meeting due date of their orders. Production of the order within due date is an important factor for improving enterprise competitiveness. The causes of occurrence of tardiness may be wrong product scheduling, unexpected events in field and so on, a way to minimize tardiness is use of alternative machines, overwork, outsourcing and etc.. In this study, we deal with a scheduling problem that can minimize tardiness using alternative machines. This paper provides a mathematical program and a heuristic method for job shop scheduling for minimizing tardiness with alternative machines. And a proposed heuristic method is verified comparing with optimal solution obtained by ILOG CPLEX.

The exact load measurements for the mechanical parts of wind turbine are important step both for evaluation of specific wind turbine design and for a certification process. A wind turbine monitoring system is essential equipment for mechanical load analysis of a wind turbine. This monitoring system is based on IEC 61400-13 and strain gage are used to measure a mechanical load of wind turbine. Also this system monitors signals from a meteorological mast. The measured signals which are sampled at 200 Hz are automatically saved on a data file in the unit of ten minutes. A detail explanation for the developed wind turbine monitoring system is presented in this study.

Belt Integrated Seat(BIS) has many advantages compared to the existing seats. Due to the development of materials and manufacturing technology, BIS, which has been used restrictely in the past, has gone through a rapid growth. As a result, its advantages have gained attention and the possibility of replacing the existing seats has grown. The need to develop BIS has risen and presently joint development with associated industries is in progress. For its first goal, the development and research of Recliner sensor has been selected. Recliner sensor is an essential part of the BIS in which the belt is incorporated onto the seat. In seat-belts, there is an inclination sensor which locks the belt according to the angle of a car. Because the inclination sensor can change frequently depending on the back of seat, a device which can enhance the inclination sensor according to the angle of the back of seat. It is the Recliner sensor that play's this role. Studies on Recliner sensor within and outside Korea has not yet made a salient progress, and due to this fact, the joint development has made a start by benchmarking other company's products. Currently, in other to set the course of the development, a research in patents and various other information is being done. In addition, for the purpose of developing a product which will be compatible with the existing products, a prototype will be made and tested before a new product makes its launching on the market.

This paper describes the mechanical and control design of a robotic device for providing therapeutic assistance to arm movement following stroke. This is a new robot for arm therapy applicable to the training of activities of daily living in homes and clinics. This instrument has one degrees of freedom, and is equipped with position and force sensors. Repetitive movement can improve movement performance in patients with neurological or orthopaedic lesions. The application of robotics can serve to assist, enhance, evaluate, and document neurological and orthopaedic rehabilitation of movements. The new robot, the mechanical structure, the control circuit, the sensors and actuators and some safety aspects.

Generally, Hertz theory is used to analyze the contact problem of two bodies. It is simple derivation of solution in the contact part. And calculation time is short Moreover, it can mean well that many wear occurs relatively. However, material property becomes plastic deformation when large perpendicular pressure acts on a small contact surface product. In this case, Hertz theory is inapplicable. Therefore this thesis carried the finite element analysis in consideration of material elasticitystrain and the shape of the geometric from contact point. And it compared with Hertz theory that change of the contact surface and contact pressure.

An increase in the amount of cracking in repaired concrete bridge decks using VES-LMC(Very Early Strength - Latex Modified Concrete ; below VES-LMC) has been noticed by Yun et al(1). Literature indicates that indeed many concrete bridge decks develop transverse cracking, most developing at early ages(3~7 days), many right after construction. The purpose of this study was to establish prevention of map, transverse and longitudinal cracking in VES-LMC and to provide a control methods for minimizing the occurrence of cracks. The proposed prevention against map and transverse cracking was verified by field applications. VES cement was modified, the unit cement contents was reduced into $360kg/m^3$ from $390kg/m^3$, the maximum size of coarse aggregate was increase into 19mm from 13mm, wire mesh and steel fibers were incorporated in concrete mixture. A series of variable combinations were attempted. As a results, the proposed prevention against map and transverse cracking was verified because no crack were occurred until 90 days after overlay.

Recently, interests on positioning system for location-based services have been significantly increased. Many indoor environment systems using fingerprint scheme have been designed to take more accuracy of positioning, but they are inefficient in adapting to change of environments. In this paper, we focus on a client-based positioning system over WLAN for decreasing installation cost and adapting to change of environments. In the proposed system, APs with stable RSSI are selected as base APs independently for each reference point. Experimental results show that proposed system expands service area approximately 20% much than traditional systems using K-NN algorithm and needs only 20% modification process to fingerprint data compare with traditional systems whenever environment conditions are changed.

A typical AP (Access Point) selection policy is to select an AP based on the received signal strength indicator (RSSI), ignoring its load. If multiple stations are deployed densely at a particular area, a typical AP selection policy will bring about the overall network throughput degradation. This paper proposes a novel AP selection policy taking into consideration not only signal strength of the APs but also AP loads to avoid Hotspot congestion. An experiment on Alinker implementing proposed AP selection policy, demonstrates that the proposed policy achieves close to optimal load balancing and grants the maximum transmission rate to stations in comparison with SSF (Strongest-Signal-First) and LLF (Least-Loaded-First).

Wireless carrier sense multiple access (CSMA) systems are widely used but show extremely different transmission efficiency according to the operation environment. Simulation or prototype deployment is needed to see the transmission efficiency of a wireless CSMA system with the partial packet retransmission scheme. The lower bound for the transmission efficiency of such a system is found mathematically in this work. This shows how much the partial packet retransmission scheme improves the transmission efficiency quantitatively. It also shows that the maximum throughput is obtained at higher offered load compared to the conventional CSMA system without the partial packet transmission. The result of this work can be applied to IEEE 802.11 networks or wireless mesh networks.

Structural and magnetic properties of $CO_{1-x}Zn_xZ$ ($Ba_3Co_{1-x}Zn_xFe_{24}O_{41}$) hexa-ferrite are studied using XRD, VSM and SEM, respectively. Powder was prepared from co-precipitation and firstly heat treated at $1350^{\circ}C$ for 6 hours in $O_2$ atmosphere. Second heat treatment was performed at 900, 1000, $1100^{\circ}C$ for 6 hours in air, respectively. Saturation magnetization value of first heat treated powder is acceptable and coercivity is high for applying to device. These result may be originated from incomplete formation reaction from M and Y phases to Z phase. Second heat treatment leads to small value of coercivity.

As of 2003, construction waste has been produced at the level of 130,614.8 tons/day, in which the amount of waste concrete was 92,639.1 tons/day and accounted for about 66.4% of the amount of construction waste. Waste concrete is mainly produced in construction work and civil engineering work. Especially, road surface crushing method using a large amount of water requires thorough management of concrete wastewater. The aim of this study was to analyze water pollution due to concrete wastewater generated in repair of bridge deck using road surface crushing equipment and to suggest reasonable countermeasures for solve the problem. In this study, it was surveyed current conditions of produced concrete wastewater in bridge deck repair, analyzed physical features of concrete wastewater, expected effects of water pollution on inflow rivers if it is not treated, established treatment plan of water pollution by categories, and calculated capacity of each treatment process and required amount of necessary chemicals. As a result of sampling wastewater generated in field sites and testing it at a lab scale, it was revealed that the original wastewater was produced in removing concrete from bridge deck slabs using surface crushing equipment whose pH was 12.53, CODMn was 12.910mg/L, SS was 547.0mg/L, and other heavy metals were included in extremely small quantities.

The Corrugated steel plate structure(CPS) can be applied to construction sites with various purposes, and the merits of CPS such as economical efficiency and swiftness can be utilized when it is constructed properly in consideration of its characteristics. However, in Korea, since the history of corrugated steel plate culvert is relatively short, there are not enough design standards. This research is prepared for finding out the causes through examining and analyzing the problems based on the examples from the existing constructions. Moreover, this study can be utilized in preparing designs and design standards of corrugated steel plate culvert in the future and devising prevention measures and complementary measures by studying construction methods considering features of construction sites and circumstances, several points to be considered while carrying out construction works and prevention measures of a problem with the existing structures.

Several contaminated bacteria such as Lactobacillus brevis and Pediococcus damnosus in beer production cause beer spoilage by producing off flavours and turbidity. Detection of these organisms is complicated by the strict anaerobic conditions and lengthy incubation times required for their cultivation, consequently there is a need for more rapid detection methods. Recently, two contaminated strains were isolated from vessel of beer production and identified as Lactobacillus species by API kit identificaton as well as 16S-23S ITS sequencing analyses. Two isolated strains were named as Lactobacillus sp. HLA1 and Lactobacillus HLB2, respectively. A polymerase chain reaction (PCR) method was developed for the rapid and specific detection of Lactobacillus sp.. Two sets of primer pairs (HLA1-F/HLA1-R and HLB2-F/HLB2-R) were designed for the amplification of a 1576 base pair (bp) fragment of the HLA1 16S-23S rRNA gene and 1888 bp fragement of the HLB2 16S-23S rRNA. Amplified PCR products were highly specific to detect corresponding bacteria when other contaminated strains were used as PCR templates. However, detection of both strains were limited when $100{\mu}{\ell}$ of cultured samples were mixed with $100m{\ell}$ of beer sample in arbitrary manner. The sensitivity of the assay still needs to be improved for direct detection of the small amounts of bacteria present in beer.

$C_p$ and other process capability indices are used extensively in industry, However, They are inadequate and widely misused. In a practical application, process average ${\mu}$ is almost always drifted by various assignable causes in process. And control charts will not detect these shifts in process average. In this study, incorporating these undetected shifts, a new capability analysis method is introduced.

Muscle force prediction in forward dynamic analysis of human motion depends many muscle parameters associated with muscle actuation. This research studies the effects of various parameters of Hill type muscle model using the simple hand raising motion. Motion analysis is carried out using motion capture system, and each muscle force is recorded for comparison with muscle model generated muscle force. Using Hill type muscle model, muscle force for generating the same hand rasing motion was setup adjusting 5 activation parameters. The test showed the importance of activation parameters on the accurate generation of muscle force.

In this paper, the swept source optical coherence tomography system has realized using a free-space interferometer based on a beam splitter. Personal computer has completed the control for tunable wavelength laser digitally and the B-scan motor as well. From each experiment for an onion and a salmon egg, we confirmed that the in vivo epidermal cross-sectional images for them can be obtained appropriately.

Recently, lots of studies are performed in developing of active orthosis. Exact and simple muscle force estimation is important in developing orthosis which assists muscle force for disabled people or physical laborers. Hill-type muscle model dynamics is common method for estimation of muscle forces. In Hill-type muscle model, we must know muscle length and moment arm which largely affect muscle force. And several methods are proposed to estimate muscle length and moment arm using joint angle. In this study, we compared estimation results of those method with data from body model of opensim to find which method is exact for estimation of muscle length and moment arm.

A low loss frequency doubler operated on low power for the RFID harmonic tags is presented. Using the excellent nonlinear characteristics of the Schottky barrier diode and proper matching networks between the diode and ports, the low conversion loss of the harmonic tag is accomplished. This doubler could be used to increase the detectable distance of the conventional RFID system adopted harmonic tags.

Practical pattern recognition systems should overcome very large class problem. Sometimes it is almost impossible to build every model for every class due to memory and time constraints. For this case, grouping similar models will be helpful. In this paper, we propose GMC(Group Model Clustering) to build a large class Chinese character recognition system. We built hidden Markov models for 10% of total classes, then classify the rest of classes into already trained group classes. Finally group models are trained using group model clustered data. Recognition is performed using only group models, in order to achieve reduced model size and improved recognition speed.

IT governance becomes one of hot issues in corporate information system including university ERP. IT governance provides IT value and mitigates IT-related risks such that the organization takes new business chances and grows in the future. In this study, we briefly introduced IT governance and university ERP in the viewpoint of alignment to the business goal of the organization. And then, we proposed an strategic approach of IT governance for university ERP system with new performance evaluation items from IT-BSC. Finally, we pointed out some related research topics as further studies.

Graphite and $MoS_2$ were added respectively to the Cu/Sn bond materials of the same composition as a lubricant in order to find out the effect of lubricants on the mechanical properties and the increase in density of the sintered products for microblades. The addition of $MoS_2$ as a lubricant was more beneficial to strength, fracture toughness, and hardness as well as densification than graphite. $MoS_2$ seemed to be more effective in reducing the friction between the metallic powders and die wall during hot pressing process. Due to the better wettability of MoS2 with bond metal alloy, less amount of interfacial defects which is detrimental to mechanical properties use observed.