Multicharacteristic quality control is concerned with monitering production processes and inspecting the quality of a lot when the state of a process or the quality of an item is determined by a number of quality characteristics. This paper reviews procedures currently available for multicharacteristic quality control when the quality characteristics are either variables or attributes.

이 논문(論文)에서는 net와 연속함수(連續函數)의 족(族)에서 상(像)에 의한 Compact 공간(空間)의 성질(性質)을 조사하였다. Compact 공간(空間)에 기초를 둔 C-closed, A-net, A-변환(變換)을 사용하여 Haussdorff 공간(空間) 혹은 Regular 공간(空間)에서의 그들의 성질(性質)을 살펴보았다.

The effect of supersaturation on morphology of silicon carbide by chemical vapor deposition using $CH_3SiCl_3-H_2$ gas mixture system was investigated. The experimental results show that the final structure of silicon carbide deposits is coarser as total pressure increases or ${\alpha}$-ratio decreases. It is believed because supersataration of Si-source decreases as total pressure increases or ${\alpha}$-ratio decreases.

The residence time distribution of liquid flow in a 4.0cm diameter column packed with porous $Al_2O_3$ spheres of 0.37cm diameter were measured with pulse injections of a tracer under cocurrent trickling flow conditions. The mean residence time of liquid flow and liquid hold-up calculated by the transient curve of tracer were unaffected by gas flow rates under experimental ranges of liquid flow rates from 2.4 to $4.5(kg/m^2\;sec)$ and gas flow rates from 0 to $0.13(kg/m^2\;sec)$. The axial dispersion coefficient of liquid stream and apparent diffusivity of tracer in a micropore of solid particle were estimated from the response curve of tracer. The calculated Peclet No. were increased in ranges of 68-to 82 with a increasing of liquid mass velocity, and the external effective contacting efficiency between liquid and solid which can be expressed. by $(D_i)_{app}/D_i$ varied in ranges of 0.54 to 0.68 depending on the liquid flow rates. The gas to liquid(water) volumetric mass transfer coefficient were determined from desorption experiments with oxygen at $25^{\circ}C$ and 1 atm. The measured mass transfer coefficients were increased with liquid flow rates and the effect of gas flow rates on the mass transfer coefficient was insignificant.

The aim of this study is to find out the relationships between the microstructures of SM45C(AISI1045) steel and fatigue crack propagation behaviour. Three microstructures such as (i) as received (fully annealed). (ii) water quenched and tempered, and (iii) oil quenched and tempered were used for fundamental mechanical testing and fatigue crack proagation test. The microstructures of (ii) and (iii) showed superior in tensile strength to (i). Resistance against fatigue crack propagation was higher in structure (i), while tensile properties were better in structures (ii) and (iii). It is believed due to that the enhancement of roughness of fracture surface obsered in structure (i) increases ${\Delta}Kth$ and lowers fatigue crack growth rate. However it does not necessarily mean the quenched and tempered structures (ii) and (iii) are undesirable for the engineering component because fatigue limit in low cycle test appears usually higher in the microstructures of higher strength.

This paper examines the effects on safety index analysis with Level II Second-Moment Method. The general two variable problem is examined by means of Cornell safety index ${\beta}c$ Rosenblueth-Esteva safety index ${\beta}_{RE}$ Rackwitz-Fiessler safety index by iterative method and Practical FOSM safety index ${\beta}_p$, which based partly on the concepts given by Paloheimo and Hannus, proposed the algorithm in this paper. The calculated examples have shown that safety index by Practical FOSM Method proposed in this paper would be similar to those in the method by Rosenblueth-Esteva or Rackwitz-Fissler and be simpler in calculation than the Rackwitz's Advanced FOSM Method, in which the iterative procedure has to be used.

A rapid and simple test to distinguish halloysite from kaolinite in mineral mixtures has been developed based on differences in the rate and extent of formamide intercalation. The results of quantitative analysis by formamide intercalation reaction GEC contained 90% of kaolin minerals, GEC contained of 86% of halloysite and GYK contained of 59% kaolinite. The extent of formamide intercalation by kaolinite was likely influenced by sample crystallinity.