Vertical drains have been commonly used to increase the rate of the consolidation of dredged material. The installation of vertical drains additionally provides a radial flow path in the dredged foundation. The objective of this study develops a numerical model for 2-D axisymmetric non-linear finite strain consolidation considering self-weight consolidation to predict the effect of vertical drain in dredged foundation which is in process of self-weight consolidation. The non-linear relationship between the void ratio and effective stress and permeability during consolidation are taken into account in the numerical model. The results of the numerical analysis are compared with that of the self-weight consolidation test in which an artificial vertical drain is installed. In addition, the numerical model developed in this paper is the simplified analytical method proposed by Ahn et, al (2010). The comparisons show that the developed numerical model can properly simulate the consolidation of the dredged material with the vertical drains installed.

This paper presents the results of a numerical investigation on the ground deformation in deep excavation with emphasis on the groundwater lowering. Using the stress-pore pressure coupled analysis Consideration to the effect of ground excavation and groundwater interaction were carried out and a series of two-dimensional finite element model was employed to perform a parametric study on a wide range of soil profile and initial ground water table condition.

Although it is important to reflect the accurate information of the ground condition in the tunnel design, the analysis and design are conducted by limited information because it is very difficult to get it practically on considering various geography and geotechnical condition. So construction management of information concept is required to manage immediately on the field condition because it is very time-consuming to establish the countermeasure of underground reinforcement and the pattern change of Bo. Therefore, when construction is on tunnel area, examination of accurate safety and prediction of behavior is performed to overcomes the limit of predicting behavior by using Artificial Neural Network(ANN) in this study. Firstly, the field data was secured. Secondly, suitable structure was made on multi-layer perceptrons among the ANN. Thirdly, learning algorithm-propagated applies to ANN. The data for the learn of field application using ANN was used by considering impact factors, which influenced the behavior of tunnel, and performing credibility analysis. crown displacement, spring displacement, subsurfacement, and rock bolt axial force are predicted at the tunnel construction and on-site application was confirmed by using ANN from analyzing and comparing with measurement value of on-site. In this study, the data from Seoul Highway $\bigcirc\bigcirc$ tunnel section was applied to the ANN Theory, and the analysis on the investigate value and the reasoning for the value associated with field application was performed.

Recently, the land area for many people has been limited because of industrialization and modernization in Korea. The large-scale constructions like the reclamation development projects have been progressed to resolve this problem mentioned above. Therefore, as many of the usefulconstruction materials as possible are needed to perform the large-scale construction projects. Many studies for the utilization of pond ash which has a similar characteristic of sand have been conducted and there has been often occurred many structural problems on roadbed in winter. Therefore, the characteristics of the freezing and thawing for Controlled Low-Strength Material (CLSM) using pond ash were analyzed and evaluated by unconfined compressive strength test in this study. As a result of this study, it was confirmed that new CLSM using pond ash with cement (8.2% by weight)was able to stand for the freezing and thawing behavior.

Shaking table tests were performed to reproduce the dynamic behavior of estuary barrage and its subbase soil which can be potentially damaged during earthquake loading. For understanding the vibration effect to the ground during earthquake, the model was formulated with 1/300 scale of prototype estuary barrage and subbase soil. Scott and Iai(1989) proposed the law of the similarity for similar experimental conditions. The laboratory model shaking table test was conducted under the vibration condition of simulated earthquake of 0.154g. The horizontal displacement on the structure was measured during the shaking table test. The pore water pressure was also monitored for the underground layers of soil. The field horizontal displacement and the pore water pressure can be predicted by using the results of the laboratory shaking table test.

Thermal properties of geomaterial are overlooked with other geomechanical properties. The transient line-source (TLS) method is one of the most used testing methods for measuring the thermal conductivity (K) and thermal diffusivity ($\alpha$) of materials. But more recently, Transient Plane-Source method was developed to measure these. It has several advantage of comparing with TSL method, but there has not been documented application in geomaterial. A Resistance Temperature Detector is used to construct sensor. For durability of Probe, Adopt a new technique that two probes are bonded in exact matching. For standard materials, such as glycerin, and ice the measured K and a values of these materials were generally within 2-5% from the standard values in the literature. This document present to evaluate the thermal properties of geomaterials and its application was tested for varying degree of saturation using the Transient Plane Source method. The result of this study suggests that it is an comparatively accurate method for simultaneously measuring thermal conductivity and thermal diffusivity and can identify the feasibility to geomaterial.

The natural soils are classified in saturated soils and unsaturated soils according to level of ground water but the research for only saturated soils has been conducted by this time. However, there are many proble.ms which are not solved by using the concept and principle of saturated soils on the natural soils. In fact, it is known that unsaturated soils represent the behavior characteristic unlike completely saturated soils because of the adhesion under the influence of negative pore water pressure, the high angle of friction and the low water permeability by the air entry. So it needs to conduct the various researches on insufficient unsaturated soils. In this paper, unsaturated triaxial compressive tests are conducted in order to do research on shear strength characteristic on sands and silty sands of Nakdong river. As a result of the tests, the cohesion is increased in non-linear type according to the change of the matric suction, but the angle of internal friction is not changed much.

Thick soft clay deposits which are generally located at the west and south coast of the Korean peninsula have complicated characteristics according to their orientation and formation history. Thus, several geotechnical problems could possibly occur when those soft clay deposits are used as foundations for marine structures. Deep cement mixing (DCM) method is one of the most widely used soft soil improvement method for various marine structures, nowadays. DCM method injects binders such as cement into the soft ground directly and mixes with the in-situ soil to improve the strength and other geotechnical properties sufficiently. However, the natural impacts induced by dynamic motions such as ocean waves, wind, typhoon, and tusnami give significant influences on the stability of marine structures and their underlaying foundations. Thus, the dynamic properties become important design criteria to insure the seismic stability of marine structures. In this study, the dynamic behavior of cemented Busan clay is evaluated. Laboratory unconfined compression test and resonant column test are performed on natural in-situ soil and cement mixed specimens to confirm the strength and strain-dependent dynamic behavior variation induced by cement mixing treatment. Results show that the unconfined compressive strength and shear modulus increase with curing time and cement content increment. Finally, the optimized cement mixing ratio for sufficient dynamic stability is obtained through this study. The results of this study are expected to be widely used to improve the reliability of seismic design for marine structures.

Around the Nakdong River which is one part of the repairing business of 4 Grand Rivers currently being constructed, sandy ground is distributed throughout the wide area. Many civil engineering structures such as small and medium sized dams, flood control basins, and redevelopment of reservoirs and retention reservoirs are scheduled to be constructed, so the prevention measures for liquefaction are surely needed. To identify such liquefaction, a lot of factor affecting the strength of liquefaction were studied through laboratory investigation. Most of the conducted study was about clean sands, but in the case of the real ground the sand can exist not in the clean conditions but in the conditions mostly including sand of fine grained soil. The sand of fine grained soil has become a significant factor to assess liquefaction because many cases of liquefaction happened in the silty and clayer soil. In this study, un-drained tests of plasticity index of fine grained particles were conducted with the sands from Nakdong River. In result, the study shows that dynamic shear strength characteristics differ according to the plasticity index.

This paper describes that estimation methods for the distribution of consolidation settlements to investigate the influence of distribution characteristics of compression index on the spatial distribution of consolidation settlements. When the variation of compression index is considerable, the spatial distribution of compression index is estimated using ordinary cokriging. The spatial distribution of consolidation settlements estimated by considering both the variation of compression index and void ratio (CASE-1) is different from the conventional mean value of all soil properties (CASE-2). The settlement of CASE-1 shows the larger variation at short distances rather than that of CASE-2. Whereas the spatial settlement distribution of CASE-1 is affected by the spatial distribution of compression index and the thickness of consolidation layer, the distribution of CASE-2 is significantly influenced by the distribution of the thickness of consolidation layer.

As enormous construction projects of land development are carried out around Korea, useful construction materials are needed to perform the construction projects. However, there are no more enough of fill and reclamation materials in our country. That is why the coal ash is expected to be utilized as an alternative material. Since the coal ash has the characteristics of a pozzolan and a selfhardening material, it is adjudged that coal ash has a great possibility to be used as a fill and reclamation material. In this study, grain size analysis, Atterberg limit test, and specific gravity test were performed to examine the physical characteristics of the coal ash about a self-hardening material before utilizing the coal ash in the construction. Compaction test, unconfined compression test were conducted to investigate the engineering characteristics according to mixture ratios of fly ash and bottom ash. As a result of the tests, it was confirmed that the mixing ratio 1:1 of fly ash and bottom ash is the most effective to use as a fill and reclamation material. If the mixture of coal ash is used as a backfill material with light weight around structure, it is expected to play a significant role in reducing earth pressure on the back of the structure. As described above, the coal ash should be considered as an alternative material of fill and reclamation materials since the result of the tests indicates that the coal ash is suitable to a useful material on the construction design.

Screw piles(Helical piles and anchors) are increasingly used to support and rehabilitate reinforced structures subjected to both tensile and compressive axial loads. This study presents a variety of detailed investigation on especially pull-out characteristics of screw piles performed to both reduced scale and numerical analysis to identify fundamental failure mechanisms and empirical optimized geometry of screw piles. It was found that the pull-out characteristics of screw piles are influenced with mainly different frequencies of compaction around soil and screw pile's pitch and followings are practical data based on empirical analysis.

This paper presents of effect of tunneling on pile group of being operated bridge using Three-dimensional numerical modeling to study the effect of coordination of tunneling location under discontinuous group pile. In order to find idealistic tunneling location that causes settlement, change of stress on the piles and movement of soil at a minimum, a fully coupled 3D finite element model is adopted. The study contains pile settlement, axial force on each piles in the group, axial displacement of piles and soil behaviour caused by tunneling. Based on the result some insights into the pile behavior due to tunneling obtained from numerical analysis were mentioned and discussed.

The thermal influential factor of energy pile system is investigated by considering the seasonal effect, saturation of ground, and fluid velocity based on the finite volume method. Analysis includes the evaluation of thermal resistance and corresponding heat exchange rate for each case. It is shown that the efficiency of heat exchange rate is more pronounced with higher fluid velocity due to the larger number of circulation for a given period. Through the parametric studies, it is also found that the degrees of saturation a little influenced thermal effect during 8 hours of operational scenario.

Granular Compaction Pile are commonly used to improve bearing capacity and reduce settlements of soft soil in coastal and lowland areas. In this paper, through the field load test results of straight granular compaction piles and taper granular compaction piles, material properties of ground and GCP for numerical analysis were drawn and numerical model was established. In the numerical analysis of taper granular compaction piles with 3 different sections, a optimum dimension of taper granular compaction pile was considered at the side of settlement.

In recent days, the foundations of huge structures in general and mega foundations of grand bridges in particular are required in geotechnical engineering. However, previous design method based on virtual fixed point theory cannot adequately predict Pile-Bent structure‘s physical behavior. Therefore, this paper describes a new analysis and design of Pile-Bent structure for grand bridges. A detailed analysis was performed for column-pile interactions using FB-Pier program and Midas program. As a result, the behavior of a column-pile is estimated and highlighted. Moreover, based on this study, it is found that the minimum reinforcement ratio(=0.4%) is applicable for plastic behavior of columns.

`Frost heave' is volumetric extension behavior of soil due to freezing. It could have a bad effect to foundations of infrastructures like building, road, railroad and bridge. Therefore, it is considered as a primary design parameter with 'adfreeze bond' and 'creep deformation' for foundation design in cold region. In some countries, studies for analyzing frost heave in many ways have being performed, however, only a few studies for evaluating frost susceptibility of soils by measuring frost heave rate of frozen soils in Korea. For analyzing frost heave as a foundation design parameter, both frost heaving rate and heaving pressure are should be addressed in study. Hence, in this study, development of experimental apparatus to evaluate frost heave and pressure is suggested.

To investigate the effect of drainage spacing and smear on the rate of consolidation, a large consolidation chamber and mandrel insertion device were developed. After the occurrence of smear by installation of sand drain, model ground was consolidated in either overconsolidated or normally consolidated state. As smear effect increases and thus drain spacing decreases, total settlement increase in overconsolidated state but has no effect in normally consolidated state. Efficiency of vertical drain decreases and consequently consolidation time increases in all tests as smear effect becomes significant.

In this study, the clay specimen of Busan-Gyeongnam region was used for unconfined compression test to compare the relationship formula between elasticity modulus at peak($E_f$), elasticity modulus at $q_u$/2($E_{50}$), and cohesion when the sample breaks down by region and by level of cohesion. As the result, the regional results were found to be in the range of $E_f$ = 14c~47c and $E_{50}$ = 43c~137c; by cohesion, the results for very soft ground was $E_f$ = 15c~40c and $E_{50}$ = 54c~101c, $E_f$ = 13c~63c and $E_{50$ = 40c~147c for soft ground, $E_f$ = 18c~47c and $E_{50}$ = 57c~144c for medium ground, and $E_f$ = 25c~45c and $E_{50}$ = 68c~115c for solid ground. The average of the relationship formula between elasticity modulus-cohesion for the clay used in this study was $E_f$ = 32c, $E_{50}$ = 93c. This is 2.5~5 times smaller than the existing relationship formula.

In this study, cohesion of soft ground, soft ground depth and embankment height varying conditions, such as the impact of each condition after the calculation of the range, SCP was performed to evaluate the applicability of the method. Reinforcing effects of scope, and permit lateral movement of SCP 2D and 3D analysis of the program were calculated by the displacement ratio, the result follows. The height and depth of soft soil embankment with increasing and decreasing the cohesion tends to be affected were long range, SCP method applied by the finite element analysis Cu = 1.0tf/$m^2$, embankment height is 3.0m depth of soft soil can be applied in a less than 5.0m, and Cu = 3.0tf/$m^2$, embankment height, the soft soil depth is 3.0m 12.0m, Cu = 3.0tf/$m^2$, embankment height is 5.0m less than 7.0m depth of soft soil can be applied in was. And Cu = 5.0tf/$m^2$, embankment height is 3.0m below 15.0m depth rouge anti Floor, Cu = 3.0tf/$m^2$, embankment height of 5.0m 12.0m depth below the soft soil, Cu = 5.0tf/$m^2$, If the depth of soft soil embankment height of 7.0m and below 5.0m was applicable.

This paper is results of analyzing causes of damage and rainfall characteristics to investigate characteristics of landslide occurrence and its causes at Inje area in Gangwondo around July in 2006 through collection of related data, literature review and field reconnaissance. From results of analyzing the geometrical characteristics of landslide slope, the slope width of showing the most probable frequency were in the range of 10~50m and the most frequent slope angle was in the range of $30{\sim}40^{\circ}$. The most probable elevation of slope was 200~300m. For the slope direction of landslides, the most frequent directions were NW and SE.

In this study, applicability of software used to analyze the lateral deformations and its shape of braced cuts, executed to excavate the ground for constructing the underground structures, was assessed by performing field measurements and numerical analyses and their behaviors were also compared with results of previous studies. Three typical sections, located at the construction site where the subway was on the process of construction at Suwon city in Gyeonggido, were chosen and the data of field measurement at those sections were collected. Numerical analyses with FEM technique of using the software PLAXIS and elasto-plastic approach of using the software MIDAS were performed. In general, the deformed shapes of braced cut, obtained from numerical approaches, were in relatively good agreements with results from field measurements. For sections of A-A and B-B, measured values were greater than analyzed ones whereas they were in relatively good agreements in the section C-C. As results of comparing the values from the measurements and the estimations, they were found to be close to each other so that numerical approaches were assessed to be appropriate to estimate the lateral deformation. The numerical technique with FEM was preferred to use because it estimated closer to the measurements than the elasto-plastic approach.

Until now, design of Earth Retaining is practiced by 2 dimensional analysis for convenience of analysis and time saving. However, the construction field is 3 dimension, in this study, practised the 3 dimensional analysis which can reflect the field condition more exactly the scope of earth retaining wall, and researched about the effective and economical way of design, compared and reviewed with the results, by practising both the 2 and 3 dimensional analysis. existing 2 dimension. the depth of excavation, depth of embedded and soil condition. As result, under the whole conditions, more displacement came to appear to the value as result of 3 dimensional analysis more than the result of 2nd dimensional analysis. Accordingly, the displacement by the 2 dimension analysis is underestimated. Moreover, results of 2 and 3 dimensional analysis, there is no difference at displacement, when the depth of embedded is 0.5H and 1.0H, but Displacement of 1.5H is smaller than 0.5H, 1.0H. That is, the bigger the depth of embedded becomes, the displacement of Earth Retaining Wall appeared smaller. The displacement of earth retaining wall according to depth of excavation appeared bigger, when the depth of excavation is increased. In the meantime, when the soil condition is different, in the 2 dimensional analysis, the displacement appeared biggest, in case of the clay layer, but in the 3 dimensional analysis, in the beginning of excavating, the displacement of earth retaining wall appeared bigger in case of clay layer, but as excavating is in progress, the displacement of both compound soil layer and sand layer appeared big.

Recently, it has been reported that number of earthquakes was rapidly increased in the Korean Peninsula. According to the interest of seismic analysis, most of construction design must ensure the stability of structure against risks due to earthquake. Therefore, the ground reinforcement and application of seismic standards is necessary and the new structures must secure a stability about Earthquake under the Korea Seismic Analysis Standards. In this study, the 2D numerical analysis was performed to confirm a seismic stability and analysed that behavior of ground and dykes. The numerical seismic response analyses for dykes and its foundation soil were conducted with considering earthquake modes of short-period and long-period, and artificial seismic wave.

This research produced internal model tester ($2.0m{\times}2.0m{\times}1.0m$) to evaluate the field application of Paju Unjeong District water recycling system for small streams eco-friendly river bed disparity method for the first time in Korea and conducted comparative analysis of the Paju Unjeong District water recycling system field test results and infiltration rate result of internal tests by each rainfall intensity following surface material. Infiltration rate result of internal tests concrete pavement by rainfall intensity following surface material, asphalt pavement, bentonite mate, stabilized soil construction and mixed soil construction manifested low infiltration rate. On the contrary, compaction soil, grassland and water permeable packaging materials resulted in significant amount of infiltration rate. As for the field permeability test results, they were manifested similar tendency as indoor permeability test results and they satisfied the standard for standard of water permeability of domestic disparity facility (less than $1.0{\times}10-7cm$/sec). As compaction rate increased, unconfined compression strength increased as well while coefficient of water permeability decreased.

Tunnel Mapper, which is tunnel face survey system was used to conduct Face Mapping on the face of the tunnel that is under construction. Then, accuracy and utility value on the forecast of discontinuity were verified to verify the field application in order to present the measures for the use of the system for conducting research on the discontinuity. As result of the directivity verification following discontinuity‘s project, forecasted measurement and actually researched measurement error for the Dip direction and Dip angle was less than ${\pm}10$. Accuracy was 82.6% for Dip direction and 90.7% for Dip angle, which are high. Accordingly, face research discontinuity forecasting system's reliability level towards directivity is high. Tunnel Mapper, a tunnel face survey system can be leveraged to replace face's visual survey and to obtain objective information, enabling execution of the survey system that can automate face survey going beyond time and space related limitations.