The surface of Alloy 600 was alloyed using a continuous wave $CO_2$ laser beam in order to improve its corrosion resistance. Laser surface alloying (LSA) was done by melting the surface electroplated with Cr of the alloy. The Cr concentration of the alloyed surface was 28-30 at.%, which is similar to that of Alloy 690. Alloying elements in the alloyed layer was observed to be distributed very homogeneously all over the alloyed region. According to the electrochemical and modified Huey tests, the corrosion resistance, in particular the grain boundary corrosion resistance, of the LSA specimens was significantly improved, compared with that of the as-received(AR) specimen. This improved corrosion resistance of the alloyed specimen might be attributed to the high Cr content which could make possible formation of more stable and dense passive film onto its surface.

This work was carried out as a fundamental experiment to fabricate a Graded-Boundary Ni/Steel material using a laser beam. A Ni sheet was placed on a steel substrate, and then a series of high power $CO_2$ laser beams were irradiated on the surface in order to produce a homogeneous alloyed layer. The processing parameters were : 4 ㎾ laser power, 2m/min traverse speeds, -2mm defocuing, 17 l/min sheiding gas flow rates. The sequential repetition of the laser surface alloying treatment up to 4 times, resulted in about 5mm thick of fair compositional gradient systems. In order to determine the microstructure, phase and compositional profiles in this material, optical microscopy, XRD and EDS were used. The compositions varied from 66% to 0% for Ni and 34% to 100% for Fe in this material The microstructures were typical morphologies of rapid solidification and solid-state cooling. Since compressive stress was formed in the heat affected region due to martensitic transformation, while relative tensile stress was developed in the alloyed region, cracks were formed between the alloyed region and the substrate region.

Laser-welded Tailored Blank is the hottest thing in many automobile companies. But they demand on weld quality, reproducibility, and formability. So it is the great problem of automation of laser welding process. Therefore, it is requested to construct on-line process monitoring system on high accuracy. The light which is emitted from plasma and spatter in laser welding was detected by photo-diodes. It was found that the light intensity depends on welding speed. laser power, and flow rate of assist gas. The relationship between the plasma and spatter and the weld quality can be used for on-line laser weld monitoring systems.

As very large scale integration technology has been developed, much more accurate, reliable technology is needed for outer lead bonding. Laser soldering has been researched as an alternative for fine pitch device bonding. This study is focused on how to select optimal laser soldering variables with which solder wets parent material, the microstructural results of laser soldering and the reliability test One of popular packages, QFP100 was soldered successfully with two kinds of solder. The inspection of the joint for reliability was carried out by optical microscope, SEM, EDAX and pull test, which demonstrated the superiority of laser soldering.

For the conventional welding method. the high heat transfer makes the crystallized zone of the work material unavoidable. Whereas the laser is able to weld the amorphous metal without a crystallized zone, because heat transfer is limited within a very small restricted volume. In this paper, the possibilities and the limits of the laser welding were studied to utilize the advantageous properties of amorphous metal foils.

In this paper, weldability and formability of Tailored-Blank (TB) and the structural impact testing of bump beam were investigated to apply TB to automobile bumper beam. The optimal $CO_2$ laser welding condition for TB of SPFC and SPRC steel plates with different thicknesses was obtained. Before welding, the cross section of butt joint was prepared only by shearing without milling process. Real type bump beam was produced by two kind of forming processes such as roll-forming and press-forming, and the good formability of TB was obtained. Impact test results of bump by using pendulum and barrier were satisfied the impact regulation of bump. Finally. It may be confirmed that laser welded TB is well-balanced material in both weight reduction and production cost of automobile bump.

This study introduces the new concept in the evaluation criteria of the $CO_2$ laser Tailored Blank weldability, The materials used are 0.7mm, 1.5mm thick low carbon automotive galvanized steels. Welding tests were conducted for both similar thickness(0.7mm-0.7mm, 1.5mm-1.5mm) and dissimilar thickness(0.7mm-1.5mm) cases. The criteria developed for optimum welding conditions were based on relationship between results of die press forming test, weld transverse tensile test Erichsen test and weld penetration measurements. Application of the developed criteria(fracture ratio, strength ratio and D/To) in obtaining optimum welding condition revealed that a weld which satisfied any of the criteria did not fracture during actual die press test.