The chemical shift of SiOC film was observed according to the flow rate ratio. SiOC film had the broad main band of $880\sim1190cm^{-1}$ and the sharp Si-$CH_3$ bond at $1252cm^{-1}$, and the peak position of the main bond in the infrared spectra moved to high frequency according to the increasing of an BTMSM flow rate. So the increment of the alkyl group induced the C-H bond condensation in the film, and shows the blueshift in the infrared spectra. In the case of P5000 system of Applied Materials Corporation, the strong bond of Si-CH3 bond in precursor does not enough to dissociated and ionized, because low plasma energy due to the capactive coupled CVD. Therefore, there was the sharp peak of Si-$CH_3$ bond at $1252cm^{-1}$.

New devices with structure of ITO/2TNATA/NPB/TCTA/CBP:7%Ir(ppy)$_3$/BCP/ETL/LiF/Al were proposed to develop high luminous green phosphorescent organic light emitting diodes and their electroluminescent properties were evaluated. The experimental devices were divided into two kinds according to the material ($Alq_3$ or SFC137) used as an electron transport layer (ETL). Luminous intensities of the devices using $Alq_3$ and SFC137 as electron transport layers were 27,500 cd/$m^2$ and 51,500 cd/$m^2$ at an applied voltage of 9V, respectively. The current efficiencies of both devices were similar as 12.6 cd/A under a luminance of 10,000 cd/$m^2$, while showed slower decay in the device with SFC137 as an ETL according to the further increase of luminance. Current density and luminance of the device with SFC137 as an electron transport layer were higher at the same voltage than those of the device with $Alq_3$ as an ETL.

The authors investigated an overhead shuttle (OHS) system for automatic transferring the liquid crystal display (LCD) panels. The constructed tracks of OHS system include the linear and curve regions and have been installed on the ceiling to transfer the cassette of LCD glass along the closed-loop and open-loop tracks. In this study, the OHS system was implemented by a proposed linear motor to solve encoder installation and the system cost problems of the long distance transfer system. In addition, we utilized a new algorithm of the position detection and a new control algorithm for driving linear motor. The newly developed control algorithm was demonstrated from both a computer simulation and an experimentation, indicating that the highly reliable and speedy transfer system can enhance the LCD panel productivity of commercial OHS system.

Application of flash memory in mobile and ubiquitous related devices is rapidly being increased due to its low price and high performance. In addition, some notebook computers currently come out into market with a SSD(Solid State Disk) instead of hard-drive based storage system. Regarding this trend, applications need to increase the storage capacity using multiple flash memory chips for larger capacity sooner or later. Flash memory based storage subsystem should resolve the performance bottleneck for writing in perspective of speed and lifetime according to its physical property. In order to make flash memory storage work with tangible performance, reclaiming of invalid regions needs to be controlled in a particular manner to decrease the number of erasures and to distribute the erasures uniformly over the whole memory space as much as possible. In this paper, we study the performance of flash memory recycling algorithms and demonstrate that the proposed algorithm shows acceptable performance for flash memory storage with multiple chips. The proposed cleaning method partitions the memory space into candidate memory regions, to be reclaimed as free, by utilizing threshold values. The proposed algorithm handles the storage system in multi-layered style. The impact of the proposed policies is evaluated through a number of experiments.

The Paper presents some potential new uses for Head-Up Displays (HUDs) in vehicular applications, where the information conveyed to the driver goes well beyond the content of today's production HUDs. Such information potentially related to the use of cellular telephones, navigation systems, vehicle to roadside communications systems, and many others. Improvements in flat panel display technologies are enabling the presentation of larger, more reconfigurable, more daylight-viewable HUD images. In addition, A Formal test and evaluation is proposed to ensure that new information displays support the driver tasks. The above developments suggest increased future opportunities for HUDs to present useful information in an as-needed, eyes-on-the-road manner.

This paper describes the fabrication and characterization of a differential pressure type integrated mass-flow controller made of stainless steel for reactive and corrosive gases. The fabricated mass-flow controller is composed of a normally closed valve and differential pressure sensor. A stacked solenoid actuator mounted on a base-block is utilized for precise and rapid control of gas flow. The differential pressure flow sensor consisting of four diaphragms can detect a flow rate by deflection of diaphragm. By a feedback control from the flow sensor to the valve actuator, it is possible to keep the flow rate constant. This device shows a fast response less than 0.3 sec. Also, this device shows accuracy less than 0.1% of full scale. It is confirmed that this device is not attacked by toxic gas, so the integrated mass-flow controller can be applied to advanced semiconductor processes which need fine mass-flow control corrosive gases with fast response.

We study the interaction of acetone molecule $[(CH_3)_2CO]$ on Si(001) surface using density functional theory. An acetone molecule is adsorbed on a Si atom of the Si dimer of the Si(001) surface. The adsorption of the acetone molecule on the Si atom at lower height between the two Si atoms of the dimer is more favorable than that on the Si atoms at upper height. Then we calculate an energy variation of dissociation and four-membered ring structures of the acetone molecule adsorbed on the Si surface. Total energy difference between the two structures is about 0.05 eV, indicating that the two structures are almost equally stable. Energy barrier exists when a hydrogen atom is dissociated and adsorbed on the other Si atom of the dimer, while energy barrier does not exist when the adsorbed acetone molecule changes to four-membered ring structure, except for the rotation of the acetone molecule along z-direction. Therefore, four-membered ring structure is kinetically more favorable than the dissociation structure when the acetone molecule is adsorbed on the Si(001) surface.

The electro-optical characteristics of the Liquid Crystal on Silicon (hereinafter "LCOS") micro-display on vertically alignment (VA) mode were studied depending on various cell gaps. 5 different cell gaps, such as $1.4{\mu}m,\;1.8{\mu}m,\;2.1{\mu}m,\;2.4{\mu}m$ and $2.8{\mu}m$, were selected. The reflectance-voltage (R-V) characteristics, distributions of reflected light and reflectance were calculated with 3-dimmensional LC code. At the center of cell, the smallest $1.4{\mu}m$ cell gap showed the lowest reflectance and the largest $2.8{\mu}m$ cell gap showed the highest reflectance due to the surface anchoring effect. In case of $2.1{\mu}m$ cell gap, the sum of reflectance overall cell was the highest value. Considering the reflectance and RV curve characteristic, the optimized cell gap was $2.1{\mu}m$.

Face detection and tracking technology on video sequence has developed indebted to commercialization of teleconference, telecommunication, front stage of surveillance system using face recognition, and video-phone applications. Complex background, color distortion by luminance effect and condition of luminance has hindered face recognition system. In this paper, we have proceeded to research of face recognition on video sequence. We extracted facial area using luminance and chrominance component on $YC_bC_r$ color space. After extracting facial area, we have developed the face recognition system applied to our improved algorithm that combined PCA and LDA. Our proposed algorithm has shown 92% recognition rate which is more accurate performance than previous methods that are applied to PCA, or combined PCA and LDA.

In this study, we investigated variations in undoped ZnO thin film properties with working pressure, $O_2$/Ar ratio, and annealing ambient. Higher vacuum pressure during deposition was observed to bring about slower growth rate resulting in samples with better crystallinity as well as hole generation efficiency through formation of shallower oxygen interstitial. Given that $O_2$/Ar ratio is greater than unity, O provided from the ambient to ZnO during annealing was found to preferably situate at interstitial sites. When He was used for the second annealing, significant changes were not observed. On the other hand, O ambient caused increased density of oxygen interstitial, thereby making the film more intrinsic-like high resistivity ZnO.

The objective of this research is to design, manufacture and test a mass flow controller capable of measuring compressible as well as incompressible fluid flows based on a 'bucket and stop-watch' method. The basic principle behind such a system is the measurement of time, where the time taken to fill and empty a bucket of known volume is measured. This device should be able to handle fluid flows in the range of 0.1 ml/min to 10 ml/min within an accuracy of ${\pm}$1%. For the flow meter to be able to compete with established designs, it must be not only comparable in cost and robustness, but also very accurate and reliable as well.

Geo-coding refers to the process of associating data with location information, and the system deals with geographic identifiers expressed as latitude and longitude or street addresses. Although many services have been launched, there still remains a problem for users to create geo-coded photo with manually labeling GPS(Global Positioning System) coordinate or synchronizing with separate devices. In this paper, we design and implement a geo-coding system which utilizes the time and location information embedded in digital photographs in order to automatically categorize a personal photo collection. An included GPS receiver labels a photograph with its corresponding GPS coordinates, and the position of the camera is automatically recorded into the photo image header at the moment of capture. The place and time where the photo was taken allows us to provide context metadata on the management and retrieval of information.