A flow control system was designed and fabricated to control the flow rate of liquid through the pipe. This control system was composed of hardwares and software, hardwares as controller, gate valve, orifice meter and data aquisition board and software as National instruments Labview program. Control of flow rate was executed by adjusting the pneumatic valve located at the center of pipe line based on the control signal generated by LabView PID control algorithm, which converts analog signal measured by pressure difference of orifice to digital signal to adjust pneumatic valve. For the controller setup Ziegler-Nichols tuning technique was applied and control performances were investigated for not only the disturbance but also the set point changes. Developed system showed good control performances in flow control enough to use as teaching tool of feedback control theory and practice in university, and also as industrial application.

This paper is concerned with the development case of CEA(Course-Embedded Assessment) design tool for engineering education accreditation operations department for CEA system implemented. Each university or programs are already devoting efforts to build research and CEA system for CEA applied to. In order to effectively apply the CEA studies for each program it is required and particularly, the preferred way to build an operating system is considered a difficult situation of the course unit. Therefore, this case study and to propose a method and procedures required to assessment the design basis for curriculum and program assessment unit in terms of the applicability of CEA, proposes a virtual application results. The information proposed in this case study is determined that could be used in the design for the outcomes and assessment of a variety of programs as one of the steps to build the CEA systems.

This study deals with how liberal education in engineering could be positioned properly in an era of convergence. Disciplines of Engineering has long been focusing on engineer as a 'technical profession' and the liberal education as an accessory to major study has been left behind. Under this understanding, the topic of 'convergence' in the 21th century engineering is hardly to find its way to the establishment into engineering education. This study suggests a direction for the reform of liberal education in engineering, which is expected to overcome the distinction between professional and non-professional aligned with major education and liberal one. For the reform, introducing and developing contents and methodologies considering convergence would open the door of engineering education to interdisciplinary study and to 'open-profession'. Next, the problem solving model in education will be very effective for learners to define the problem, to utilize various knowledges and to lead to meaningful solution. Lastly, we emphasize the changing context of liberal education and it is necessary to integrate 'technology literacy' into liberal education in relation to major study.

A camp program where the theory of inventive problem solving TRIZ is applied to real problems of the industry was developed and taught at a five-day seminar apart from the standard curriculum at a university D in Gyeonggido. This study focuses on the educational effect that the TRIZ method has on the engineering students when their creative problem solving skills are required to solve industry problems on their own with the knowledge from their courses. For five days, the students were educated about TRIZ and assigned a real industry problem "Removal of friction caused by bubble formation in water heating pipelines". By applying TRIZ to the problem, the students developed an "Air removing Air Arrester" which received the evaluation, "with understanding the system architecture and the task objective causes and formation of the problem could be handled which directly helps the company's R&D". In this case, TRIZ offers the students a guideline and knowledge on how to approach problems and as a result the students provided a practical solution. During the process, the TRIZ method instilled confidence in the students and proved to be a motivation. It becomes obvious that this short-term program has a positive effect on students' way of thinking creatively and increasing their problem-solving abilities.

This study was conducted to explore the applicability and effects of Smart Support System for Creative Problem Solving(S3CPS) in engineering education. S3CPS is an online system developed to support learners' creative problem solving activities based on the CPS model proposed by Treffinger et al.(2000). In this study, it was applied in an engineering course in which students work in teams to design and produce creative robots with the purpose of verifying its effects on creative problem solving and team projects. To address the purpose, interviews and surveys were carried out to examine the effects of S3CPS. The qualitative data were analyzed through a generic coding process. Three ways to apply S3CPS in an engineering course based on team project were derived and effects of the system were also analyzed. It implies that specific design guidelines are required for the optimal use of the system for existing engineering courses.

The employment rate of a college has long been one of the most important elements in college survival strategies. Employment rates may not be key to colleges' survival in other countries, but they are fundamental to colleges in Korea as seen in the Korean government-led National Competency Standard (NCS), which has been underway since its introduction to colleges in Korea. Against this backdrop, if the engineering accreditation system can contribute to improving employment rate in this context, it can take root more quickly. The process conducive to improving employment rates can be classified as both direct and indirect methods. With dwindling school-age population having impacts on colleges and universities, the environment and the education directions of colleges have rapidly been shifting since the introduction of the NCS. Therefore, various survival strategies for colleges need to be developed. An indicator of employment rate of college graduates is among the most important things during this transition process. The Department of Mechanical Engineering at Koje College has consistently shown good records during the past 5 years by matching the accreditation schemes and employment strategies. The department will help put in place the engineering technology education accreditation system at the college through its various innovative and effective programs. To formulate a better employment strategy, it is needed to reflect and consolidate the engineering accreditation scheme into the existing employment policy of college. In short, this paper examines both the engineering accreditation scheme and the employment policy in ways that helps produce a coupling matrix structure. This study looks into the measures for improving employment rates by better adjusting the engineering education methods under the accreditation scheme.

Along with the industry growth, engineering colleges in Korea has have a quantitative growth. Many of the policy promotions and budgets for engineering colleges from the government are supported. And the various monitoring methods to verify their achievement have demanded. This paper deals with the construction of engineering educational statistics system in Korea. It named Korea Engineering Data Management System(K-EDMS). This system is based on the data mining tool and supports data-based decision making for an advanced engineering education service. This paper presents related researches of case studies. Then, we have designed K-EDMS, and constructed 157 cases for engineering colleges of the year 2014.

This paper deals with the selection method of effective engineering design problem based on LEGO Mindstorm NXT for basic design education. By YouTube case study of various LEGO-based engineering designs for olympic sports, performance criteria have been developed including programming complexity, structural complexity, sensor/actuator complexity and variety of game operation. Programming complexity includes range of programming code length and possible program variety. Structural complexity includes variety of structural elements such as length, shape, weight, and volume to overcome design restrictions. Sensor/actuator complexity includes variety of sensor used and number of possible actuator assemblies. Variety of game operation includes game complexity and required creativity to make LEGO robots. Based on these performance criteria, four representative sports were selected as the candidates for effective engineering design problem. Finally, feasibility and attributes of each candidate were verified by real implementation examples.

This paper deals with a result of case study for the development of CEA(Course-Embedded Assessment) design tool for engineering education accreditation implementing programs. Many programs have been devoting efforts to apply CEA to their engineering education. In order to effectively apply the CEA to educational program, it is required to develop the standardized form or scheme for CEA application. As a preliminary approach, we propose the design tool and the result of a case study for CEA application in engineering education.

The purpose of this study is to identify core elements required of instruction consulting and to develop a systematic consulting procedure for successful Flipped Learning. The main contents of this study to achieve its purpose are as follows. First, core elements required of consulting are deduced by analyzing cases of instruction implemented with Flipped Learning. Second, consulting procedure is constructed based on core consulting elements of Flipped Learning. Based on the study results, the 3P process is suggested as the elements and procedure of instruction consulting for Flipped Learning. The 3P process has the following characteristics. The first stage Preparation involves guiding students to have an objective viewpoint about the lesson beginning with building a relationship with the instructor. Also, a lesson plan and source materials for lesson are selected and developed. The second stage Performance involves implementing lesson coaching oriented towards cooperative problem-solving to find better direction. The last stage Post-review involves introspection necessary for continuous quality improvement of lessons. The validity of the instruction consulting elements for Flipped Learning applied to deduce the aforementioned results has been verified after specialist review and field application.

Today, the world economy is changing rapidly thanks to the rapid progress of glottalization and the development of technology. It is important to analyze and offer specialized start-ups effect factors for collegians in order to systematically and successfully support technology-centered start-ups of collegians. Through which Entrepreneurship and job creation in developed countries. This study explores the current status and characteristics of Entrepreneurship education in Korea and suggests some directions for effective management of Entrepreneurship education.

An engineering educational servery for graduating seniors had been conducted in Songwon University to improve engineering program objectives. The analysis results show that the current engineering educational objectives need to be modified to satisfy the ABEEK accredited criteria and engineering curriculum returning is necessary to include more design courses.

This paper examines the industry field training education model, analyze the operational status proposed improvement measures. Data were analyzed using a field training participating students participating industry last three years. On the other hand analysis field training participating students increased, industry participation has decreased. And most of the students took part in the seasonal short-term job training. In addition, it was difficult to analyze the employment status field training operations follow-up member. In this paper, a field training operations support system management models and practical training courses organized field trips how to improve. Field training operations support will be strengthened through the work associated with the company expanding participation model introduced and is expected to increase in the long-term practical training, students participate in field training system improvement. Run the job training Improvement in future research presented in this paper attempts to analyze the students' employment status and results of operations involved.

This study was implemented for the purpose of analyzing the Job Competency level of accredited and non-accredited program's graduates. And we were seeking way to manage realistic and effective way of Accreditation of Engineering education. In order to achieve the purpose of this study, survey and FGI were done. The study was: accredited program's graduates thought more positively than non-accredited program's graduates, and graduates felt that 11 Job Competencies Level of Work Performance were lower than the needs of job performance. The conclusions of this study were summarized as follows: First, between accredited and non-accredited program's graduates, we could see significant recognition difference about the perception of the needs of job performance. This was because Design curriculum were reinforced and accredited program's graduates had attended design program at accredited program. Second, accredited program's graduates felt higher than non-accredited program's graduates about the perception of level of work performance. This was because the efforts for curriculum reorganizing and teaching methods improvement were done. Third, we could not find significant recognition difference about the perception of the needs for job performance and work level. That was because accredited and non-accredited program were not dealed seperately. The conclusions of this study are summarized as follows: First, The efforts for analyzing job competence of industry and reflecting the program curriculum are needed on the accredited program for engineering education. Second, Government should make the incentive policy about the companies which give some merits to the accreditation graduates, and monitor constantly their real working. Third, in order that the accreditation results can be trustful on staff recruiting or school choosing, accreditation should make outcome-based-evaluation which guarantees competence of graduates.