• 한국표면공학회지
• /
• 제31권5호
• /
• pp.237-244
• /
• 1998

In this stydy, submicron shallow trenches applied to STI(shallow tench isolation) were etched using inductively coupled $CI_2$/HBr and $CI_2/N_2$plasmas and the physical and electrical defects remaining on the etched silicon trench surfaces and the effects of various annealing and oxidation on the removal of the defects were studied. Using high resolution electron microscopy(HRTEM), Physical defects were investigated on the silicon trench surfaces etched in both 90%$CI_2$/ 10%$N_2$ and 50%$CI_2$/50%HBr. Among the areas in the tench such as trench bottom, bottom edge, and sidewall, the most dense defects were found near the trench bottom edge, and the least dense defects were found near the trench bottom edge, and least dense defects compared to that etched with ment as well as hydrogen permeation. Thermal oxidation of 200$\AA$ atthe temperature up to $1100^{\circ}C$apprars not to remove the defects formed on the etched silicon trenches for both of the etch conditions. To remove the physicall defects, an annealing treatment at the temperature high than $1000^{\circ}C$ in N for30minutes was required. Electrical defects measured using a capacitance-voltage technique showed the reduction of the defects with increasing annealing temperature, and the trends were similar to the results on the physical defects obtained using transmission electron microscopy.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 추계학술대회 논문집 학회본부 C
• /
• pp.723-725
• /
• 1998

STI CMP process are substituting gradually for LOCOS(Local Oxidation of Silicon) process to be available below sub-0.5um technology and to get planarized. The other hand, STI CMP process(especially STI CMP with RIE etch back process) has some kinds of defect like Nitride residue, Torn Oxide defect, etc. In this paper, we studied how to reduce Torn Oxide defects after STI CMP with RIE etch back process. Although Torn Oxide defects which occur on Oxide on Trench area is not deep and not sever, Torn oxide defects on Moat area is sometimes very deep and makes the yield loss. We did test on pattern wafers witch go through Trench process, APCVD process, and RIE etch back process by using an REC 472 polisher, IC1000/SUV A4 PAD and KOH base slurry to reduce the number of torn defects and to study what is the root causes of torn oxide defects.

• Journal of Korean Vacuum Science & Technology
• /
• 제2권2호
• /
• pp.122-132
• /
• 1998

Characteristics of inductively coupled Cl2/O2 and Cl2/N2 plasmas and their effects on the formation of submicron deep trench etching of single crystal silicon have been investigated using Langmuir probe, quadrupole mass spectrometer (QMS), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM), Also, when silicon is etched with oxygen added chlorine plasmas, etch products recombined with oxygen such as SiClxOy emerged and Si-O bondings were found on the etched silicon surface. However, when nitrogen is added to chlorine, no etch products recombined with nitrogen nor Si-N bondings were found on the etched silicon surface. When deep silicon trenches were teached, the characteristics of Cl2/O2 and Cl2/N2 plasmas changed the thickness of the sidewall residue (passivation layer) and the etch profile. Vertical deep submicron trench profiles having the aspect ratio higher than 5 could be obtained by controlling the thickness of the residue formed on the trench sidewall using Cl2(O2/N2) plasmas.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1996년도 재료학회 춘계학술발표회
• /
• pp.64-64
• /
• 1996

• 한국전기전자재료학회논문지
• /
• 제15권10호
• /
• pp.838-843
• /
• 2002

Chemical mechanical polishing(CMP) process has been widely used to planarize dielectric layers, which can be applied to the integrated circuits for deep sub-micron technology. The reverse moat etch process has been used for the shallow trench isolation(STI)-chemical mechanical polishing(CMP) process with conventional low selectivity slurries. Thus, the process became more complex, and the defects were seriously increased. In this paper, we studied the direct STI-CMP process without reverse moat etch step using high selectivity slurry(HSS). As our experimental results show, it was possible to achieve a global planarization without the complicated reverse moat process, the STI-CMP process could be dramatically simplified, and the defect level was reduced. Therefore the throughput, yield, and stability in the ULSI semiconductor device fabrication could be greatly improved.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1997년도 한국재료학회 추계학술발표회
• /
• pp.103-103
• /
• 1997

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.88-89
• /
• 2009

In this paper, we investigated about wet cleaning effect as deep trench formation methods for Power chip devices. Deep trench structure was classified by two methods, PSU (Poly Stick Up) and Non-PSU structure. In this paper, we could remove residue defect during wet. cleaning after deep trench etch process for non-PSU structure device as to change wet cleaning process condition. V-SEM result showed void image at the trench bottom site due to residue defect and residue component was oxide by EDS analysis. In order to find the reason of happening residue defect, we experimented about various process conditions. So, defect source was that oxide film was re-deposited at trench bottom by changed to hydrophobic property at substrate during hard mask removal process. Therefore, in order to removal residue defect, we added in-situ SCI during hard mask removal process, and defect was removed perfectly. And WLR (Wafer Level Reliability) test result was no difference between normal and optimized process condition.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2005년도 추계종합학술대회
• /
• pp.833-836
• /
• 2005

Nano-gap trench is fabricated by the novel electrochemical etching technique using forward biased PN junction formed at the backside of the wafer. PN junction is formed using boron nitride wafer and the concentration of the boron doping is the high value of $1{\times}10^{19}$ $cm^{-3}$. The electro-chemical etching is performed in the 5% HF solution under the forward bias voltage of $1{\sim}2V$. The relationship between the etch rate of the trench and the voltage of the forward bias is investigated and the dependence of the gap for the voltage also examined. The etch rate increase from 0.027 ${\mu}m/min$ to 0.031 ${\mu}m/min$ as the value of the applied voltage increase from 1V to 2V, but the the gap is kept constant value of 40 nm.

• 한국전기전자재료학회논문지
• /
• 제27권8호
• /
• pp.497-500
• /
• 2014

In this paper, we analyze electrical characteristics of n/p-pillar layer according to trench angle which is the most important characteristics of SJ MOSFET and core process. Because research target is 600 V class SJ MOSFET, so conclusively trench angle deduced 89.5 degree to implement the breakdown voltage 750 V with 30% margin rate. we found that on resistance is $22mohm{\cdot}cm^2$ and threshold voltage is 3.5 V. Moreover, depletion layer of electric field distribution also uniformly distributes.

• 한국진공학회지
• /
• 제6권4호
• /
• pp.364-371
• /
• 1997

MERIE 플라즈마 장비를 사용하여 실리콘의 트렌치 식각을 HBr, He-$O_2,SiF_4,CF_4$ 등의 가스를 주입하여 수행하였으며 식각 속도, 식각 프로파일 변화, 잔류물 생성 및 표면 상태 등을 관찰하였다. HBr만을 이용한 플라즈마 식각시에는 트렌치 하부 영역에 상당한 횡방향 식각이 일어나 항아리 모양의 식각 프로파일이 관찰되었으며, HBr에 He-$O_2$가스와 $SiF_4$나 $CF_4$등의 주입량을 변화시켜 벽면 기울기와 횡방향 식각의 정도를 제어할 수 있었다. 표면 잔류물 특성 및 표면 거칠기(roughness)등은 HBr/He-$O_2$/$SiF_4$가스를 동시에 주입하여 식각하였을 때 가장 양호한 식각 특성을 나타내었으며, 첨가 가스로 $SiF_4$를 이용함으로써 기존의 C-F계 플라즈마를 이용한 트렌치 식각 특성들보다 우수한 공정 결과를 얻었다. 또 한 $SiF_4$를 이용함으로써 $CF_4$ 첨가시보다 C의 잔류물을 크게 줄이고 표면 손상을 개선할 수 잇음을 X-선 광전자 분석과 주사전자현미경(scanning electron microscopy) 및 AFM(atomic force microscopy)의 결과로써 확인하였다.