• Journal of Sensor Science and Technology
• /
• v.3 no.2
• /
• pp.74-80
• /
• 1994

Silicon direct bonding technology is very attractive for both silicon-on-insulator devices and sensor fabrication because of its thermal stress free structure and stability. The process of SDB includes hydration of silicon wafer and heat treatment in a wet oxidation furnace. After hydration process, hydroxyl groups of silicon wafer were analyzed by using Fourier transformation-infrared spectroscopy. In case of hydrophilic treatment using a ($H_{2}O_{2}\;:\;H_{2}SO_{4}$) solution, hydroxyl groups are observed in a broad band around the 3474 $cm^{-1}$ region. However, hydroxyl groups do not appear in case of diluted HF solution. The bonded wafer was etched by using tetramethylammonium hydroxide etchant. The surface of the self etch-stopped silicon dioxide is completely flat, so that it can be used as sensor applications such as pressure, flow and acceleration, etc..

• Proceedings of the KIEE Conference
• /
• 1999.07g
• /
• pp.3310-3312
• /
• 1999

We have studied the method of silicon direct bonding using the mixture of $HNO_$, $H_2O_2$, and HF chemicals called the controlled slight etch (CSE) solution for the effective wafer cleaning. CSE, two combinations of oxidizing and etching agents, have been used to clean the silicon surfaces prior to wafer bonding. Two wafers of silicon and silicon dioxide were contacted each other at room temperature and postannealed at $300{\sim}1100^{\circ}C$ in $N_2$ ambient for 2.5 h. We have cleaned silicon wafers with the various HF concentrations and characterized the parameters with regard to surface roughness, chemical nature, chemical oxide thickness, and bonding energy. It was observed that the chemical oxide thickness on silicon wafer decreased with increasing HF concentrations. The initial interfacial energy and final energy postannealed at $1100^{\circ}C$ for 2.5h measured by the crack propagation method was 122 $mJ/m^2$ and 2.96 $mJ/m^2$, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.81-84
• /
• 1995

A reliable bonding between two silicon wafers, regularly grooved and non-grooved, was done by the direct boning technology, It is Presented that high structural duality was realized not only at the bended interface but in the bulk, commensurate with the filling of artificial grooves, which would be attributed to the dislocation-gettering capability of groove free-surfaces during annealing. The groove filling would be explained with mass-transport phenomena assisted by the dislocation movement from initial contact boundaries toward groove surfaces. Intrinsic voids can be easily removed by aid of the grooves. The proposed method yielded also an intimate bonding not only between {111} wafers strongly misoriented and slightly inclined to {111} basal plane but even between {111} and {100} orientation wafers.

• Transactions on Electrical and Electronic Materials
• /
• v.1 no.1
• /
• pp.6-11
• /
• 2000

The hydrogen plasma treatment of silicon wafers in the reactive ion-etching mode was studied for the application to silicon-on-insulator wafers which were prepared using the wafer bonding technique. The chemical reactions of hydrogen plasma with surface were used for both surface activation and removal of surface contaminants. As a result of exposure of silicon wafers to the plasma, an active oxide layer was found on the surface. This layer was rendered hydrophilic. The surface roughness and morphology were examined as functions of the plasma exposing time and power. In addition, the surface became smoother with the shorter plasma exposing time and power. The value of initial surface energy estimated by the crack propagation method was 506 mJ/㎡, which was up to about three times higher as compared to the case of conventional direct using the wet RCA cleaning method.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.759-762
• /
• 2000

Present transistors which have vertical structure show increased parasitic capacitance characteristics in accordance with the increase of non-active base area and collector area, consequently have disadvantage for high speed switching performance. In this paper, a horizontal structure transistor which has minimized parasitic capacitance in virtue of SDB(Silicon Direct Bonding) wafer and oxide sidewall isolation utilizing silicon trench technology is presented. Its structural characteristics were designed by ATHENA(SUPREM4), the process simulator from SILVACO International, and its performance was proven by ATLAS, the device simulator from SILVACO International. The performance of the proposed horizontal structure transistor was certified through the VCE-lC characteristics curve, $h_{FE}$ -IC characteristics, and GP-plot.

• Proceedings of the KIEE Conference
• /
• 1999.07g
• /
• pp.3279-3281
• /
• 1999

This paper describes a method of direct wafer bonding using surfaces activated by a radio-frequency hydrogen plasma. The hydrogen plasma cleaning of silicon in the RIE mode was investigated as a pretreatment for silicon direct bonding. The cleaned silicon surface was successfully terminated by hydrogen, The hydrogen-terminated surfaces were rendered hydrophilic, which could be wetted by Dl water rinse. Two wafers of silicon and silicon dioxide were contacted to each other at room temperature and postannealed at $300{\sim}1100^{\circ}C$ in an $N_2$ atmosphere for 2 h. From the AFM results, it was revealed that the surface became rougher with the increased plasma exposure time and power. The effect of the plasma treatment on the surface chemistry was investigated by the AES analysis. It was shown that the carbon contamination at the surface could be reduced below 5 at %. The interfacial energy measured by the crack propagation method was 122 $mJ/m^2$ and 384 $mJ/m^2$ for RCA cleaning and hydrogen plasm, respectively.

• The Bulletin of The Korean Astronomical Society
• /
• v.36 no.2
• /
• pp.125.2-125.2
• /
• 2011

We are developing medium resolution cross-dispersed silicon grisms in the near IR region ($1.45{\sim}5.2{\mu}m$). The grisms will be installed in MIMIR, a multifunction instrument at the Lowel Observatory, USA. The two devices are designed to cover H and K band and L and M band simultaneously. Our goal is to make grism with R=3000 at 1.2 arcsec slit. The Silicon has high refractive index (n=3.4 at $1.5{\mu}m$) which enhances the resolving power by up to 5 times when compared to conventional material such as BK-7 (n=1.5 at 1.5 ${\mu}m$). The bonded grisms will be installed in a filter wheel for the uses switch from spectroscopic mode to imaging mode easily. Our device is compact and light weighted while it provides a decent resolving power. We produce monolithic grisms using e-beam lithography at the NASA JPL and chemically etching the grooves on the silicon prisms. Moreover, the main-disperser and cross-disperser will be contacted together by direct Si-Si bonding technique and eventually turn into one piece. The bonded pair offers more stability in terms of the layout of the spectrum and removes the Fresnel loss at the intersection of two grisms. We report on the proper wafer bonding steps through this research, and inspected the bonding quality thermally, optically and mechanically.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.169-174
• /
• 2001

This paper reports on the development of high aspect ratio structure and 3-D integrated process for MEMS-based micro gas turbines. To manufacture high aspect ratio structures, Deep Reactive Ion Etching (DRIE) process have been developed and optimized. Specially, in this study, structures with aspect ratios greater than 10 were fabricated. Also, wafer direct bonding and Infra-Red (IR) camera bonding inspection systems have been developed. Moreover, using glass/silicon wafer direct bonding, we optimized the 3-D integrated process.

• Journal of the Korean institute of surface engineering
• /
• v.33 no.2
• /
• pp.101-106
• /
• 2000

SOI (Silicon-On-Insulator) substrates were fabricated with varying annealing temperature of $25-660^{\circ}C$ by a linear annealing method, which was modified RTA process using a linear shape heat source. The annealing method was applied to Si ∥ $SiO_2$/Si pair pre-contacted at room temperature after wet cleaning process. The bonding strength of SOI substrates was measured by two methods of Razor-blade crack opening and direct tensile test. The fractured surfaces after direct tensile test were also investigated by the optical microscope as well as $\alpha$-STEP gauge. The interface bonding energy was 1140mJ/m$^2$ at the annealing temperature of $430^{\circ}C$. The fracture strength was about 21MPa at the temperature of $430^{\circ}C$. These mechanical properties were not reported with the conventional furnace annealing or rapid thermal annealing method at the temperature below $500^{\circ}C$. Our results imply that the bonded wafer pair could endure CMP (Chemo-Mechanical Polishing) or Lapping process without debonding, fracture or dopant redistribution.

• Korean Journal of Materials Research
• /
• v.16 no.10
• /
• pp.652-655
• /
• 2006

A direct wafer bonding process necessary for GaAs-on-insulator (GOI) fabrication with high thermal annealing temperatures was studied by using PECVD oxides between gallium arsenide and silicon wafers. In order to apply some uniform pressure on initially-bonded wafer pairs, a graphite sample holder was used for wafer bonding. Also, a tool for measuring the tensile forces was fabricated to measure the wafer bonding strengths of both initially-bonded and thermally-annealed samples. GaAs/$SiO_2$/Si wafers with 0.5-$\mu$m-thick PECVD oxides were annealed from $100^{\circ}C\;to\;600^{\circ}C$. Maximum bonding strengths of about 84 N were obtained in the annealing temperature range of $400{\sim}500^{\circ}C$. The bonded wafers were not separated up to $600^{\circ}C$. As a result, the GOI wafers with high annealing temperatures were demonstrated for the first time.