• Journal of KSNVE
• /
• v.9 no.5
• /
• pp.928-935
• /
• 1999

Vertical pumps are widely used owing to the fact that they occupy small floor space. In this type of pumps, however, the vibrational problems are very important, since, in many cases, they have less stiffness in comparison with lateral pumps. This study presents a simple solution method for calculating the natural frequencies and modes of vertical pumps. In this study, a mode of a vertical pump was developed and the nondimensional parameters for the vibrational characteristics of it were determined. Added mass was calculated for the effects of water and the transfer matrix method was used.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.815-818
• /
• 2006

This paper deals with the free, in-plane vibrations of curved members with the translational(radial and tangential directions) and rotational springs at the ends. The governing differential equations for the circular curved member are solved numerically using the corresponding boundary conditions. The lowest three natural frequencies and the corresponding mode shapes are obtained over a range of non-dimensional system parameters: the subtended angle, the slenderness ratio, the translational spring stiffness, and the rotational spring stiffness.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.6
• /
• pp.1496-1502
• /
• 1994

The influences of spring position and spring stiffness on the critical force of a cantilevered beam subjected to a follower force are investigated. The spring attatched to the beam is assumed to be a translational one and can be located at arbitrary positions of the beam as it has not been assumed so far. The effects of transeverse shear deformation and rotary intertia of the beam are also included in this analysis. The charateristic equation for the system is derived and a finite element model of the beam using local coordinates is formulated through extended Hamilton's principle. It is found that when the spring is located at position less than that of 0.5L, the flutter type instability only exists. It is shown that the spring position approaches to the free end of the beam from its midpoint, instability type is changed from flutter to divergence through the jump phenomina according to the increase of spring stiffness.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.5
• /
• pp.606-612
• /
• 1985

On the stability of the Beck's column with a tip mass, the influence of the characteristics of the springs at the fixed end of the column are studied. The equations of motion and boundary conditions of this system are established by using the Hamiton's principle. On the evaluation of the stability of the column, t he effect of the shear deformation and rotatory inertial is considered in calculation. For the maintenance of the stability of the column, it is proved that the constant of the translational spring at the fixed end must be very large while th magnitude of the constant of the rotational spring at the fixed end has no effect. When the constants of the springs at the fixed end are small, it is also proved that the influence of the moment of inertial of the tip mass on the stability of the column are decreased and for the translational spring the degree of the decrease is more and more. Therefore it is found that the characteristics of the springs at the fixed end are very effective elements for the stability of the column when the columns subjected to a compressive follower force are designed.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.4
• /
• pp.71-78
• /
• 2008

In the case of the railway bridges, uplift forces were occurred at the edge of the segments when vehicular loads were applied. These forces caused the compressive and tensile forces in the fastening system. In the past, a structural analysis has been performed to investigate the safety of fastening system which was modeled with one directional spring elements based on the compressive test of fastening system. In this case, the stiffness of the spring element was obtained from experimental study which was conducted by compressive load. Therefore, to perform rational and exact structural analysis, the translational stiffness of the fastening system obtained from the experimental study applied the tensile load and the rotational stiffness should be considered because it was occurred the tensile force as well as the compressive force in fastening system. In this study, an elastic and inelastic experimental study was performed for six specimens. The translational stiffness along the vertical axis of rail and the rotational stiffness along the strong axis of rail were investigated, also structural behavior of the fastening system was analyzed.

• Journal of the Society of Naval Architects of Korea
• /
• v.30 no.1
• /
• pp.125-133
• /
• 1993

Most studies on the vibration analysis of a beam-column with ends elastically restrained and various intermediate constraints have been based on the Euler beam theory, which is inadequate for beam-columns of low slenderness ratios. In this paper, analytical methods for vibration and dynamic sensitivity of a Timoshenko beam-column with ends elastically restrained and various intermediate constraints are presented. Firstly, an exact solution method is shown. Since the exact method requires considerable computational effort, a Rayleigh-Ritz analysis is also investigated. In the latter two kinds of trial functions are examined for comparisions : eigenfunctions of the base system(the system without intermediate constraints) and polynomials having properties corresponding to the eigenfunctions of the base system. The results of some numerical Investigations show that the Rayleigh-Ritz analysis using the characteristic polynomials is competitive with the exact solutions in accuracy, and that it is much more efficient in computations than using the eigenfunctions of the base system, especially in the dynamic sensitivity analysis. In addition, the prediction of the changes of natural frequencies due to the changes of design variables based on the first order sensitivity is in good agreements with that by the ordinary reanalysis as long as the changes of design variables are moderate.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.10a
• /
• pp.420-425
• /
• 1997

본 연구에서는 병진 스프링과 회전 스프링으로 동시에 지지되어 있으며 다수의 집중질량과 회전관성이 결합된 멀티스팬빔의 무차원 설계변수에 따른 진동특성의 엄밀해를 빠른 계산속도로 해석할 수 있는 이론적 진동해석 방법을 제시하였다. 그리고, 지금까지 연구되어 온 여러 가지 해석모델에 적용하여 본 연구에서 이용한 해석기법의 타당성을 검증하였다.

• Journal of Ocean Engineering and Technology
• /
• v.6 no.1
• /
• pp.69-77
• /
• 1992

The natural frequencies of a beam on elastic foundation are investigated in the present paper. The inhomogeneous elastic foundation can be modelled as a combination of distributed translational spring, rotational spring, intermediate supports and dampers. The natural frequencies and mode shapes of the system are obtained by using the Galerkin's method, and also compared with the results in the literature. Furthermore, the natural frequencies of the beam with elastically mounted masses, which can be used as vibration absorbers, are obtained by an efficient numerical scheme suggested in the present paper.

• Journal of KSNVE
• /
• v.8 no.5
• /
• pp.856-861
• /
• 1998

Several reactor system components, such as heat exchange tubes, fuel fins, controlrods, and various instruments are beam-like components. This study presents a simple solution method for calculating the natural frequencies and modes of beams supported by linear and torsional springs and attached concentrated mass and rotational inertia at some intermediate points. For a general multi-span beam, theoretical method is proposed to analyze the exact solution about vibrational characteristics with respect to the nondimensional parameters. And the results obtained using the numerical models are presented and discussed.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.61-68
• /
• 1991

The system such as railway bridge can be modelled as the restrained beam with intermediate supports. This kind of structures are subject to the moving load, which has a great effect on dynamic stresses and can cause sever motions, especially at high velocities. Therefore, to analyze the dynamic characteristics of the system due to the moving load is very important. In this paper, the governing equation of motion of a restrained beam subjected to the moving load is derived by using the Hamilton's principle. The orthogonal polynomial functions, which are trial functions and satisfying the geometric and dynamic boundary conditions, are obtained through simple procedure. The dynamic response of the system subjected to the moving loads is obtained by using the Galerkin's method and the numerical time integration technique. The numerical tests for various constraint, velocity and boundary conditions were preformed. Furthermore, the effects of mass of the moving load are studied in detail.