• Journal of information and communication convergence engineering
• /
• v.11 no.4
• /
• pp.288-292
• /
• 2013

In this paper, a carbon implant is investigated in detail from the perspectives of performance advantages and side effects for the thick n-type metal-oxide-semiconductor field-effect transistor (n-MOSFET). Threshold voltage ($V_{th}$) adjustment using a carbon implant significantly improves the $V_{th}$ mismatch performance in a thick (3.3-V) n-MOS transistor. It has been reported that a bad mismatch occurs particularly in the case of 0.11-${\mu}m$ $V_{th}$ node technology. This paper investigates a carbon implant process as a promising candidate for the optimal $V_{th}$ roll-off curve. The carbon implant makes the $V_{th}$ roll-off curve perfectly flat, which is explained in detail. Further, the mechanism of hot carrier injection lifetime degradation by the carbon implant is investigated, and new process integration involving the addition of a nitrogen implant in the lightly doped drain process is offered as its solution. This paper presents the critical side effects, such as Isub increases and device performance shifts caused by the carbon implant and suggests an efficient method to avoid these issues.

• Journal of Satellite, Information and Communications
• /
• v.9 no.4
• /
• pp.63-68
• /
• 2014

Electrostatic Discharge(ESD) protection performance of PPS(PMOS pass structure) embedded N-type silicon controlled rectifier(NSCR_PPS) device with different partial p-well(PPW) structure was discussed for high voltage I/O applications. A conventional NSCR_PPS standard device shows typical SCR-like characteristics with low on-resistance, low snapback holding voltage and low thermal breakdown voltage, which may cause latch-up problem during normal operation. However, our proposed NSCR_PPS devices with modified PPW demonstrate the stable ESD protection performance with high latch-up immunity.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.4
• /
• pp.17-23
• /
• 2018

Recently, electric semiconductors became an issue because of efficient use of energy and compaction of electronics. Silicon electric semiconductors are difficult to put into it because of its physical limitations. Hence, the study of WBG (Wideband Gap) semiconductors like SiC and GaN began. These devices received attention because it can be miniaturized and worked at high temperatures over $300^{\circ}C$. WBG MOSFET electric semiconductors can show performance like silicon IGBT. This can solve the current problem of IGBT tail. The current study shows the technical principles and issues related to SiC and GaN power semiconductors. WBG devices can achieve high performance compared to silicon, but its performance can't be fully utilized because of lack in bonding technology. Therefore, this review introduces research on WBG devices and their packaging issues.

• Journal of Satellite, Information and Communications
• /
• v.10 no.4
• /
• pp.6-11
• /
• 2015

The ESD(electrostatic discharge) protection performance of PPS(PMOS pass structure) embedded N-type silicon controlled rectifier(NSCR_PPS) device with different GPNS(Gate to Primary $N^+$ Diffusion Space) structure was discussed for high voltage I/O applications. A conventional NSCR_PPS standard device with FPW(Full P-Well) structure and non-CPS(Counter Pocket Source) implant shows typical SCR-like characteristics with low on-resistance(Ron), low snapback holding voltage(Vh) and low thermal breakdown voltage(Vtb), which may cause latch-up problem during normal operation. However, our proposed NSCR_PPS devices with modified PPW(Partial P-Well) structure and optimal CPS implant demonstrate the improved ESD protection performance as a function of GPNS variation. GPNS was a important parameter, which is satisfied design window of ESD protection device.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.259-259
• /
• 2016

반도체 산업 전반에 걸쳐 이루어지고 있는 연구는 소자를 더 작게 만들면서도 구동능력은 우수한 소자를 만들어내는 것이라고 할 수 있다. 따라서 소자의 미세화와 함께 트랜지스터의 구동능력의 향상을 위한 기술개발에 대한 필요성이 점차 커지고 있으며, 고유전(high-k)재료를 트랜지스터의 게이트 절연막으로 이용하는 방법이 개발되고 있다. High-k 재료를 트랜지스터의 게이트 절연막에 적용하면 낮은 전압으로 소자를 구동할 수 있어서 소비전력이 감소하고 소자의 미세화 측면에서도 매우 유리하다. 그러나, 초미세화된 소자를 제작하기 위하여 high-k 절연막의 두께를 줄이게 되면, 전기적 용량(capacitance)은 커지지만 에너지 밴드 오프셋(band-offset)이 기존의 실리콘 산화막(SiO2)보다 작고 또한 열공정에 의해 쉽게 결정화가 이루어지기 때문에 누설전류가 발생하여 소자의 열화를 초래할 수 있다. 따라서, 최근에는 이러한 문제를 해결하기 위하여 게이트 절연막 엔지니어링을 통해서 누설전류를 줄이면서 전기적 용량을 확보할 수 있는 연구가 주목받고 있다. 본 실험에서는 high-k 물질인 Ta2O5와 SiO2를 적층시켜서 누설전류를 줄이면서 동시에 높은 캐패시턴스를 달성할 수 있는 게이트 절연막 엔지니어링에 대한 연구를 진행하였다. 먼저 n-type Si 기판을 표준 RCA 세정한 다음, RF sputter를 사용하여 두께가 Ta2O5/SiO2 = 50/0, 50/5, 50/10, 25/10, 25/5 nm인 적층구조의 게이트 절연막을 형성하였다. 다음으로 Al 게이트 전극을 150 nm의 두께로 증착한 다음, 전기적 특성 개선을 위하여 furnace N2 분위기에서 $400^{\circ}C$로 30분간 후속 열처리를 진행하여 MOS capacitor 소자를 제작하였고, I-V 및 C-V 측정을 통하여 형성된 게이트 절연막의 전기적 특성을 평가하였다. 그 결과, Ta2O5/SiO2 = 50/0, 50/5, 50/10 nm인 게이트 절연막들은 누설전류는 낮지만, 큰 용량을 얻을 수 없었다. 한편, Ta2O5/SiO2 = 25/10, 25/5 nm의 조합에서는 충분한 용량을 확보할 수 있었다. 적층된 게이트 절연막의 유전상수는 25/5 nm, 25/10 nm 각각 8.3, 7.6으로 비슷하였지만, 문턱치 전압(VTH)은 각각 -0.64 V, -0.18 V로 25/10 nm가 0 V에 보다 근접한 값을 나타내었다. 한편, 누설전류는 25/10 nm가 25/5 nm보다 약 20 nA (@5 V) 낮은 것을 확인할 수 있었으며 절연파괴전압(breakdown voltage)도 증가한 것을 확인하였다. 결론적으로 Ta2O5/SiO2 적층 절연막의 두께가 25nm/10nm에서 최적의 특성을 얻을 수 있었으며, 본 실험과 같이 게이트 절연막 엔지니어링을 통하여 효과적으로 누설전류를 줄이고 게이트 용량을 증가시킴으로써 고집적화된 소자의 제작에 유용한 기술로 기대된다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.8
• /
• pp.5541-5549
• /
• 2015

This paper introduces a safer and more power efficient heater by using induction heating, to apply to the semiconductor wafer fabrication exhaust gas cleaning system. The exhaust gas cleaning system is currently made with filament heater that generates an endothermic reaction of N2 gas for the removal of moisture. Induction theory, through the bases of theoretical optimization and electronic implementation, is applied in the design of the induction heater specifically for the semiconductor wafer exhaust system. The new induction heating design provides a solution to the issues with the current energy inefficient, unreliable, and unsafe design. A robust and calibrated design of the induction heater is used to optimize the energy consumption. Optimization is based on the calibrated ZVS induction circuit design specified by the resonant frequency of the exhaust pipe. The fail-safe energy limiter embedded in the system uses a voltage regulator through the feedback of the MOSFET control, which allows the system performance to operate within the specification of the N2 Heater unit. A specification and performance comparison from current conventional filament heater is made with the calibrated induction heater design for numerical analysis and the proof of a better design.

• ETRI Journal
• /
• v.14 no.1
• /
• pp.40-51
• /
• 1992

$0.25{\mu} m$ 급 pMOSFET소자를 구현하기 위해, $P^+$ 폴리실리콘을 적용한 pMOS를 제작하였으며, $p^+$ 폴리실리콘 게이트 소자에서 심각하게 문제가 되고 있는 붕소이온 침투현상을 조사하고 붕소이온 침투가 일어나지 않는 최적열처리온도를 조사하였다. 소자제조 공정중 게이트 공정만 전자선 (EBML300)을 이용하여 직접묘사하고 그 이외의 공정은 stepper(gline) 을 사용하는 Mix & Match 방법을 사용하였다. 또한 붕소이온 침투현상을 억제하기 위한 한가지 예로서, 실리콘산화막과 실리콘질화막을 적층한 ONO(Oxide/Nitride/Oxide) 구조를 게이트 유전체로 적용한 소자를 제작하여 그 가능성을 조사하였다. 그 결과 $850^{\circ}C$의 온도와 $N_2$ 분위기에서 30분동안 열처리 하였을 경우, 붕소이온의 침투현상이 일어나지 않음을 SIMS(Secondary Ion Mass Spectrometer) 분석 및 C-V(Capacitance-Voltage) 측정으로 확인할 수 있었으며 그 이상의 온도에서는 붕소이온이 침투되어 flat band전압(Vfb)을 변화시킴을 알았다. 6nm의 얇은 게이트 산화막 및 $0.1{\mu} m$ 이하의 LDD(Lightly Doped Drain) $p^-$의 얇은 접합을 형성함으로써 소자의 채널길이가 $0.2 {\mu} m$까지 짧은 채널효과가 거의 없는 소자제작이 가능하였으며, 전류구동능력은 $0.26\muA$/$\mu$m(L=0.2$\mu$m, V$_DS$=2.5V)이었고, subthreshold 기울기는 89-85mV/dec.를 얻었다. 붕소이온의 침투현상을 억제하기 위한 한가지 방법으로 ONO 유전체를 소자에 적용한 결과, $900^{\circ}C$에서 30분의 열처리조건에서도 붕소이온 침투현상이 일어나지 않음으로 미루어 , $SiO_2$ 게이트 유전체보다 ONO 게이트 유전체가 boron 침투에 대해서 좋은 장벽 역활을 함을 알았다. ONO 게이트 유전체를 적용한 소자의 경우, subthreshold특성은 84mV/dec로서 좋은 turn on,off 특성을 얻었으나, ONO 게이트 유전체는 막자체의 누설전류와 실리콘과 유전체 계면의 고정전하량인 Qss의 양이 공정조건에 따라 변화가 심해서 문턱전압 조절이 어려워 소자적용시 문제가 된다. 최근 바닥 산화막(bottom oxide) 두께가 최적화된 ONO 게이트 유전체에 대하 연구가 활발히 진행됨을 미루어, 바닥 산화막 최적화가 된다면 더 좋은 결과가 예상된다.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.10
• /
• pp.123-129
• /
• 1996

LDD structure is widely accepted in fabricating short channel MOSFETs due to reduced short channel effect originated form lower drain edge electric field. However, modeling of the LDD device is troublesome because the analysis methods of LDD region known are either too complicated or inaccurate. To solve the problem, this paper presents a nonlinear resistance model for the LDD region based on teh fact that the electron mobility changes with positive gate bias because accumulation layer of electrons is formed at the surface of the LDD region. To prove the usefulness of the model, single source/drain and LDD nMOSFETs were fabricated with 0.35$\mu$m CMOS technolgoy. For the fabricated devices we have measured I$_{ds}$-V$_{gs}$ characteristics and compare them to the modeling resutls. First of all, we calculated channel and LDD region mobility from I$_{ds}$-V$_{gs}$ characteristics of 1050$\AA$ sidewall, 5$\mu$m channel length LDD NMOSFET. Then we MOSFET and found good agreement with experiments. Next, we use calculated channel and LDD region mobility to model I$_{ds}$-V$_{gs}$ characteristics of LDD mMOSFET with 1400 and 1750$\AA$ sidewall and 5$\mu$m channel length and obtained good agreement with experiment. The single source/drain device characteristic modeling results indicates that the cahnnel mobility obtained form our model in LDD device is accurate. In the meantime, we found that the LDD region mobility is governed by phonon and surface roughness scattering from electric field dependence of the mobility. The proposed model is useful in device and circuit simulation because it can model LDD device successfully even though it is mathematically simple.

• Journal of IKEEE
• /
• v.11 no.1 s.20
• /
• pp.69-76
• /
• 2007

This paper presents the design of LVDS (Low-Voltage-Differential-Signaling) transmitter for Gb/s-per-pin operation. The proposed LVDS transmitter is designed using BiCMOS technology, which can be compatible with CMOS technology. To reduce chip area and enhance the robustness of LVDS transmitter, the MOS switches of transmitter are replaced with lateral bipolar transistor. The common emitter current gain($\beta$) of designed bipolar transistor is 20 and the cell size of LVDS transmitter is $0.01mm^2$. Also the proposed LVDS driver is operated at 1.8V and the maximum data rate is 2.8Gb/s approximately In addition, a novel ESD protection circuit is designed to protect the ESD phenomenon. This structure has low latch-up phenomenon by using turn on/off character of P-channel MOSFET and low triggering voltage by N-channel MOSFET in the SCR structure. The triggering voltage and holding voltage are simulated to 2.2V, 1.1V respectively.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.6
• /
• pp.655-661
• /
• 2013

In this paper, the 1/f noise characteristics of n-channel MOSFET (NMOSFET) and p-channel MOSFET (PMOSFET) are analyzed in depth as a function of body bias. The normalized drain current noise, $S_{ID}/I_D{^2}$ showed strong dependence on the body bias in the sub-threshold region for both NMOSFET and PMOSFET, and NMOSFET showed stronger dependence than PMOSFET on the body bias. On the contrary, both of NMOSFET and PMOSFET do not exhibit the dependence of $S_{ID}/I_D{^2}$ on body bias in strong inversion region, although the noise mechanisms of two MOSFETs are different from each other.