• ETRI Journal
• /
• v.34 no.4
• /
• pp.485-491
• /
• 2012

In this paper, the implementations of a $0.1{\mu}m$ gallium arsenide (GaAs) pseudomorphic high electron mobility transistor process for a low noise amplifier (LNA), a subharmonically pumped (SHP) mixer, and a single-chip receiver for 70/80 GHz point-to-point communications are presented. To obtain high-gain performance and good flatness for a 15 GHz (71 GHz to 86 GHz) wideband LNA, a five-stage input/output port transmission line matching method is used. To decrease the package loss and cost, 2nd and 4th SHP mixers were designed. From the measured results, the five-stage LNA shows a gain of 23 dB and a noise figure of 4.5 dB. The 2nd and 4th SHP mixers show conversion losses of 12 dB and 17 dB and input P1dB of -1.5 dBm to 1.5 dBm. Finally, a single-chip receiver based on the 4th SHP mixer shows a gain of 6 dB, a noise figure of 6 dB, and an input P1dB of -21 dBm.

• Applied Chemistry for Engineering
• /
• v.7 no.1
• /
• pp.18-25
• /
• 1996

Power input in stirred vessel is especially important in the design of mixers, as well as the evaluation of mixing processes. A type of baffles in mechanically agitated vessels and power employed are major factors that determine the stirring efficiency in a large scale, multi-step processes. In the present study, power input in the totally baffled agitated vesseles was compared systematically in connection with several previous studies and adequate power input correlation was found to be : $Np_{(pitch)}=({\theta}/90^{\circ})Np_{(90^{\circ})}$ Power number correlation was dependent upon the distance of among the impeller in the agitated vesseles, as follows : $$Np=7.09(n_p)^{0.7}(\frac{b_(double)}{d})(\frac{H}{D})^{0.18}$$, $${n_p}^{0.7}(\frac{b_{(double)}}d)$$<2 $$Np=8.73\{(n_p)^{0.7}(\frac{b_{(double)}}{d})\}^{0.7}(\frac{H}{D})^{0.18}$$, $${n_p}^{0.7}(\frac{b_{(double)}}d)$$>2.

• Journal of electromagnetic engineering and science
• /
• v.5 no.3
• /
• pp.112-116
• /
• 2005

This paper presents a broadband two-stage low noise amplifier(LNA) operating from 3 to 10 GHz, designed with 0.18 ${\mu}m$ RF CMOS technology, The cascode feedback topology and broadband matching technique are used to achieve broadband performance and input/output matching characteristics. The proposed UWB LNA results in the low noise figure(NF) of 3.4 dB, input/output return loss($S_{11}/S_{22}$) of lower than -10 dB, and power gain of 14.5 dB with gain flatness of $\pm$1 -dB within the required bandwidth. The input-referred third-order intercept point($IIP_3$) and the input-referred 1-dB compression point($P_{ldB}$) are -7 dBm and -17 dBm, respectively.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.2
• /
• pp.45-49
• /
• 2009

In this paper, a direct down conversion LNA/Mixer has been designed and tested for 900Mhz UHF RFID application. The designed circuit has been implemented in 0.18um CMOS technology with 3.3V operation. In this work, a common gate input architecture has been used to cope with the higher input self jamming level. This LNA/Mixer is designed to support two operating modes of high gain mode and low gain mode according to the input jamming levels. The measured results show that the input referred P1dBs are 4dBm of high gain mode and 11dBm of low gain mode, and the conversion gains are 12dB and 3dB in high and low gain mode respectively The power consumptions are 60mW for high gain mode and 79mW for low gain mode. The noise figures are 16dB and 20dB in high gain mode and low gain mode respectively.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2002.11a
• /
• pp.77-81
• /
• 2002

This paper demonstrates a CMOS downconversion mixer for 2.4GHz ISM band applications. The mixer, implemented in a 0.18um CMOS process, is based on the CMOS Gilbert Cell mixer, With a 2.5GHz local oscillator and a 2.45GHz RF input, the measurement results exhibit power conversion gam of -6dB, IIP3 of -6dBm, input $P_{-1dB}$ of -15 dBm, and power dissipation in mixer core of 2.7 mW with 0㏈m LO power and 1.8V supply voltage.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.609-610
• /
• 2006

A 77GHz MMIC transceiver module consisting of a power amplifier, a low noise amplifier, a drive amplifier, a frequency doubler and a down-mixer has been developed for automotive forward-looking radar sensor. The MMIC chip set was fabricated using $0.15{\mu}m$ gate-length InGaAs/InAlAs/GaAs mHEMT process based on 4-inch substrate. The power amplifier demonstrated a measured small signal gain of over 20dB from $76{\sim}77GHz$ with 15.5dBm output power. The chip size is $2mm{\times}2mm$. The low noise amplifier achieved a gain of 20dB in a band between $76{\sim}77\;GHz$ with an output power of 10dBm. The chip size is $2.2mm{\times}2mm$. The driver amplifier exhibited a gain of 23dB over a $76{\sim}77\;GHz$ band with an output power of 13dBm. The chip size is $2.1mm{\times}2mm$. The frequency doubler achieved an output power of -16dBm at 76.5GHz with a conversion gain of -16dB for an input power of 10dBm and a 38.25GHz input frequency. The chip size is $1.2mm{\times}1.2mm$. The down-mixer demonstrated a measured conversion gain of over -9dB. The chip size is $1.3mm{\times}1.9mm$. The transceiver module achieved an output power of 10dBm in a band between $76{\sim}77GHz$ with a receiver P1dB of -28dBm. The module size is $8{\times}9.5{\times}2.4mm^3$. This MMIC transceiver module is suitable for the 77GHz automotive radar systems and related applications in W-band.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.8
• /
• pp.1263-1268
• /
• 2008

In this paper, the low noise power amplifier for GaAs FET ATF-10136 is designed and fabricated with active bias circuit and self bias circuit. To supply most suitable voltage and current, active bias circuit is designed. Active biasing offers the advantage that variations in the pinch-off voltage($V_p$) and saturated drain current($I_{DSS}$) will not necessitate a change in either the source or drain resistor value for a given bias condition. The active bias network automatically sets a gate-source voltage($V_{gs}$) for the desired drain voltage and drain current. Using resistive decoupling circuits, a signal at low frequency is dissipated by a resistor. This design method increases the stability of the LNA, suitable for input stage matching and gate source bias. The LNA is fabricated on FR-4 substrate with active and self bias circuit, and integrated in aluminum housing. As a results, the characteristics of the active and self bias circuit LNA implemented more than 13 dB and 14 dB in gain, lower than 1 dB and 1.1 dB in noise figure, 1.7 and 1.8 input VSWR at normalized frequency $1.4{\sim}1.6$, respectively.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.6
• /
• pp.141-147
• /
• 2008

This paper describes the design of frequency down converting Mixer in the receiver to use compound semiconductor and CMOS product process. The basic theory and structure of frequency down converting Mixer is surveyed, and we design mixer circuit with active balun which use the compound semiconductor and CMOS process. This mixer convert a single ended signal to differential signal at input port of RF and LO instead of matching circuit to get dual band balanced mixer structure and characteristic broadband. This designed mixer has a conversion gain $-1{\sim}-6[dB]$ at $2{\sim}6[GHz]$ bandwidths. However, the simulation of the designed mixer with active balun has the result of a 7[dB] conversion gain for -2[dBm] LO input power and -10[dBm] input P1[dB] at 5.8[GHz].

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.4
• /
• pp.506-514
• /
• 1998

The design and fabrication of X-band(11.7~12 GHz) 2-stage monolithic microwave integrated circuit(MMIC) low noise amplifier (LNA) for active antenna are presented using $0.15{\mu}m\times140{\mu}m$ AlGaAs/InGaAs/GaAs pseudomorphic high electron mobility transistor (P-HEMT). In each stage of the LNA, a series feedback by using a source inductor is used for both input matching and good stability. The measurement results are achieved as an input return loss under -17 dB, an output return loss under -15dB, a noise figure of 1.3dB, and a gain of 17 dB at X-band. This results almost concur with a design results except noise figure(NF). The chip size of the MMIC LNA is $1.43\times1.27$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.9 s.100
• /
• pp.957-963
• /
• 2005

This paper presents technique of wideband TIA for optical communication systems using TSMC 0.25 ${\mu}m$ CMOS RF-Mixed mode. In order to improve bandwidth characteristics of an TIA, we use active inductor shunt peaking to cascode and common-source configuration. The result shows the 37 mW and 45 mW power dissipation with 2.5 V bias and 61 dB$\Omega$ and 61.4 dB$\Omega$ transimpedance gain. And the -3 dB bandwidth of the TIA is enhanced from 0.8 GHz to 1.45 GHz in cascode and 0.61 GHz to 0.9 GHz in common-source. And the input noise current density is $5 pA/\sqrt{Hz}$ and $4.5 pA/\sqrt{Hz}$, and -10 dB out put return loss is obtained in 1.45 GHz. The total size of the chip is $1150{\times}940{\mu}m^2$.