• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.513-516
• /
• 2008

최근 건설경기의 침체 및 원자재가 상승 그리고 후분양제의 시행 등으로 인해 공사기간 단축에 의한 공사비 절감에 대한 요구가 증가하고 있다. 공사기간 단축을 위한 방안으로 조강 콘크리트를 사용하여 양생기간을 단축시키는 방법이 일반적으로 사용되어지나 기존의 조강시멘트나 조강혼화제를 사용할 경우 고가의 재료비용이 소요될 뿐 아니라, 콘크리트의 초기 수화열 증가 및 작업성 저하 등의여러 가지 문제가 발생되고 있다. 본 연구에서는 조강형 결합재와 혼화제를 사용한 콘크리트의 현장에 적용하여 거푸집 탈형 시기를 앞당김으로써 공기단축에 의한 공사비 절감을 달성하고자 한다. 조강형 결합재와 혼화제를 사용한 콘크리트의 현장 적용성을 확인하기 위하여 기존의 조강시멘트와 조강혼화제를 사용한 콘크리트와 함께 경시변화시험 및 응결시간 측정시험 그리고 압축강도시험 등의 비교 시험을 실시하였다.

• 한국건축시공학회지
• /
• 제18권3호
• /
• pp.251-257
• /
• 2018

여름철 콘크리트는 수분증발에 의한 소성 및 건조수축균열, 슬럼프 저하, 콜드조인트 발생 등 다양한 문제가 발생한다. 이에 국내에서는 수분증발을 방지하고, 단열성능을 확보하기 위해 표면피복 양생을 위한 다양한 형태의 버블시트를 제작하여 사용하고 있으나, 여름철에는 적용사례가 없었다. 따라서 본 연구에서는 여름철 시공중인 아파트 현장에 1중의 투명, 백색 및 알루미늄 증착 버블시트와 PE필름 및 표면노출의 5가지 표면피복 양생재를 적용하여 콘크리트의 온도 및 균열특성 등 품질에 미치는 영향을 분석하였다. 실험결과 알루미늄 증착 버블시트가 온도저감, 균열저감 면에서 가장 뛰어난 것으로 나타났지만, 알루미늄 재질의 특성상 빛이 반사되어 시공자의 눈부심에 따른 시각공해가 발생하기 때문에 백색 버블시트의 사용이 가장 효과적인 것으로 밝혀졌다.

• 대한토목학회논문집
• /
• 제44권4호
• /
• pp.433-441
• /
• 2024

본 연구는 기존 국내 건축물의 동결을 방지를 위해 열선을 매립한 토목 및 건축물의 열선으로 인한 외부 에너지 사용으로 탄소 배출 및 유지관리비용이 증가하는 것을 절감시킬 수 있는 에너지 효율을 증대한 에너지 저장 시멘트 복합체를 제안한다. 최근 탄소 저감을 위해 상변화 물질(PCM)을 일반 시멘트 복합체에 통합하여 잠열 성능을 부여하는 연구가 진행되어왔다. 그러나 상변화 물질을 혼입한 콘크리트의 경우 상변화 물질의 유출, 강도 저하 및 부족한 열적 성능 등에서 문제점을 보이는 경향이 있다. 본 연구에서는 이러한 문제를 극복하기 위해 마이크로캡슐을 이용하여 상변화 물질을 캡슐화시켜 시멘트 복합체에 혼입하고 다중벽탄소나노튜브와 실리카 퓸을 사용하여 시멘트 복합체의 강도 감소를 최소화시킨 고효율 열저장 시멘트 복합체를 제안한다. 열선을 매립한 환경에서 보통 시멘트 복합체를 대체하여 고효율 열저장 시멘트를 사용한 경우 약 42 %의 에너지를 저감하는 효과를 보여주었으며 PCM만 혼입한 시멘트 복합체에 비해 압축강도, 휨강도는 각각 18 %, 23 %을 개선하여 사용성을 입증하였다.

• 플랜트 저널
• /
• 제13권2호
• /
• pp.46-51
• /
• 2017

본 연구에서는 정격출력 870MW, 대향류 석탄보일러의 최상부층 버너운전에 따른 보일러 연소상태 변화와 보일러 효율을 측정하였다. 시험방법은 하부와 중간층 버너가 운전중인 상태에서 최상부층 전방버너, 전,후방 버너 동시 운전, 후방 버너 운전으로 구분하여 최상부층 버너 운전에 따른 보일러 효율을 측정하였으며 시험 결과 최상부층 전 후방 버너 동시운전 > 최상부층 전방 버너 > 최상부층 후방 버너 운전의 순으로 보일러 효율이 높게 나타났다. 최상부층 전방과 후방 버너를 동시에 운전할 경우 보일러 노 내 열흡수율 증가 및 대류전열면 좌우 증기온도 편차가 감소되었다. 보일러 열흡수율 개선에 따라 보일러 배기가스손실 감소 및 석탄공급량이 후방버너 운전 대비 8t/h 감소하였으며, 이는 연료비 절감은 물론 온실가스 배출량 감축에도 크게 기여할 것으로 판단된다.

• 한국자동차공학회논문집
• /
• 제4권2호
• /
• pp.11-22
• /
• 1996

It has been generally accepted that NOx formation increases as the maximum temperature or correspondingly the maximum pressure of a combustion system increases. Recently some exceptional experimental results have been reportes that under certain circumstance NOx formation could be reduced while the maximum pressure was increasing by varying the methods of combustion for the same kind of premixed gases. Until now that kind of results have been acquired only for the case of a dual opposed prechamber. But the mechanism has not been clearly understood yet. 3D computer simulation has been tried to clarify the mechanism. Flor this purpose KIVA-Ⅱ has been modified and applied to the model combustion chamber with which the same kind of experimental works have been done by the authors. A good agreement with the experimental results was achieved with the spatial and temporal resolution which is hard th be obtained by the experimental methods. And it was observed that for the dual opposed prechamber case the time for the NOx formation, which is non-equilibrium reaction, is shorter than any other case by an appropriate mixing process in the main combustion chamber. The shorter time reduceed heat loss through the combustion chamber walls and thereby obtaines the higher maximum pressure.

• 한국태양에너지학회 논문집
• /
• 제32권2호
• /
• pp.58-63
• /
• 2012

As the exterior of building has been considered one of th important parts, the use of glass that is suitable to express various appearances gets raised. However, windows have 6~7times lower insulating performance than insulated walls. Lately, highly efficient windows are required as the needs for reduction of energy consumption come to the force. Therefore, Nowadays more people use cooling systems in summer, more the use of Low-E glazing is increasing. Because it is good to block Solar Radiant Energy which can cause much of heat loss while cooling system is working. This study measures U-value of the double Low-E glazing window and commonly used single Low-E glazing window. And then the effect of each window on the efficiency rating has been analyzed applying to the certification system of the building energy efficiency rating which has implemented.

• Bulletin of the Korean Chemical Society
• /
• 제28권12호
• /
• pp.2279-2282
• /
• 2007

Highly crystalline, uniform Fe nanoparticles were successfully synthesized and encapsulated in zirconia shell using sol-gel process. Two different approaches have been employed for the coating of Fe nanoparticle with zirconia. The thickness of zirconia shell can be readily controlled by altering molar ratio of Fe nanoparticle core to zirconia precursor in the first case where as reaction time was found to be most effective parameter to controlled the shell thickness in the second method. The structure and magnetic properties of the ZrO2-coated Fe nanoparticles were studied. TEM and HRTEM images show a typical core/shell structure in which spherical α-iron crystal sized of ~25 nm is surrounded by amorphous ZrO2 coating layer. TGA study showed an evidence of weight loss of less than 2% over the temperature range of 50-500 °C. The nanoparticles are basically in ferromagnetic state and their magnetic properties depend strongly on annealing temperature. The thermal treatment carried out in as-prepared sample resulted in reduction of coercivity and an increase in saturation magnetization. X-ray diffraction experiments on the samples after annealing at 400-600 °C indicate that the size of the Fe@ZrO2 particles is increased slightly with increasing annealing temperature, indicating the ZrO2 coating layer is effective to interrupt growing of iron particle according to heat treatment.

• 한국세라믹학회지
• /
• 제28권4호
• /
• pp.261-268
• /
• 1991

The dielectric properties and microstructure of SrTiO3-based grain boundary layer (GBL) capacitor were investigated, and SrTiO3 GBL capacitor was made by penetrating the Frit (PbO-Bi2O3-B2O3 system). The Nb2O5-doped SrTiO3 ceramics were fired for 4-hours, at 145$0^{\circ}C$ in H2-N2 atomsphere to get semiconductive ceramics. The grain size of SrTiO3 sintered at reduction atmosphere had increased as the amount of Nb2O5 increases and then decreased as the amount of Nb2O5 exceeded 0.2 mole%. Insulating reagents which contained PbO-Bi2O3-B2O3 system frit and oxide mixture were printed on the each semiconductive ceramics and fired at varying temperature and for different holding time. The optimum dielectric properties could be obtained by second heat treatment at 110$0^{\circ}C$ for 1 hour, when frit paste was printed. A SrTiO3-based GBLC had the apparent permitivity of about 3.2$\times$104, the dielectric loss of 0.01~0.02 and the stable temperature coefficient of capacitance. The influence of frit paste on dielectric properties was similiar to that of oxide paste but the stability of temperature property of capacitance was improved.

• 한국주조공학회지
• /
• 제31권6호
• /
• pp.336-341
• /
• 2011

Recently, aluminium usage in the automobile industry has been increased cause of its lightweight. The aluminium has a melting-solidification process in producing line and another melting process was needed in manufacturing process. Two times of melting process for making ingot and casting not only makes the loss of time and money but contaminates the air with Sox, Nox. For this reason, the holding furnace with laminated adiabatic material was developed. This holding furnace can deliver the molten aluminium directly to the industry needing molten aluminium. Recent holding furnace has above $15^{\circ}C/h$ of cooling rate and that causes solidification of molten aluminium. The ANSYS software was used to analysis the heat transfer. The adiabatic materials were laminated with optimized arrangement and holding furnace shape was changed with optimized modelling by ANSYS analysis for reducing the cooling rate of molten aluminium in holding furnace.

• 전력전자학회논문지
• /
• 제22권4호
• /
• pp.345-352
• /
• 2017

In this paper, a non-dissipative snubber for reducing the switching losses in the step down converter is proposed. The conventional step down converter, e.g., buck converter, suffers from serious switching losses and consequentially heat generation because of its hard switching. Thus, it is unsuitable for high switching frequency operation. Reduction of the reactive components' size, such as an output inductor and capacitor, is difficult. The proposed snubber can slow down the increasing current slopes and switch voltage at turn-on and turn-off transients, thereby significantly reducing the switching loses. Additionally, the slowly increasing current during switch turn-on transition, can effectively solve the output rectifier diode reverse recovery problem. Therefore, the proposed non-dissipative snubber not only leads to the efficiency of converter operation at high switching frequency but also reduces the reactive components size in proportion to the switching frequency. To confirm the validity of the proposed circuit, theoretical analysis and experimental results from a 150 W, 1 MHz prototype are presented.