• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.10
• /
• pp.64-69
• /
• 2015

Self-heating effects of bulk and SOI FinFETs on device structure are examined with TCAD simulation. The degradation of drive current in SOI FinFET is severer than that of bulk one in steady-state condition as expected. However, it is shown that the dynamic self-heating effects of SOI FinFETs are comparable to those of bulk FinFETs for high speed logic operation, especially in realistic device structure.

• Vacuum Magazine
• /
• v.3 no.1
• /
• pp.16-21
• /
• 2016

FinFETs are able to be scaled down to 22 nm and beyond while suppressing effectively short channel effect, and have superior performance compared to 2-dimensional (2-D) MOSFETs. Bulk FinFETs are built on bulk Si wafers which have less defect density and lower cost than SOI(Silicon-On-Insulator) wafers. In contrast to SOI FinFETs, bulk FinFETs have no floating body effect and better heat transfer rate to the substrate while keeping nearly the same scalability. The bulk FinFET has been developed at 14 nm technology node, and applied in mass production of AP and CPU since 2015. In the development of the bulk FinFETs at 10 nm and beyond, self-heating effects (SHE) is becoming important. Accurate control of device geometry and threshold voltage between devices is also important. The random telegraph noise (RTN) would be problematic in scaled FinFET which has narrow fin width and small fin height.

• Journal of Convergence for Information Technology
• /
• v.11 no.11
• /
• pp.159-165
• /
• 2021

A fin channel with a fin width of 20 nm and a gradually increased source/drain extension regions are fabricated on a bulk silicon wafer by using a three-dimensional selective oxidation. The detailed process steps to fabricate the proposed fin channel are explained. We are demonstrating their preliminary characteristics and properties compared with those of the conventional fin field effect transistor device (FinFET) and the bulk FinFET device via three-dimensional device simulation. Compared to control devices, the three-dimensional selective oxidation fin channel MOSFET shows a higher linear transconductance, larger drive current, and lower series resistance with nearly the same scaling-down characteristics.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.2
• /
• pp.191-197
• /
• 2016

In this paper, we investigated the hotcarrier injection (HCI) mechanism, one of the most important reliability issues, in 10 nm node Input/Output (I/O) bulk FinFET. The FinFET has much intensive HCI damage in Fin-bottom region, while the HCI damage for planar device has relatively uniform behavior. The local damage behavior in the FinFET is due to the geometrical characteristics. Also, the HCI is significantly affected by doping profile, which could change the worst HCI bias condition. This work suggested comprehensive understanding of HCI mechanisms and the guideline of doping profile in 10 nm node I/O bulk FinFET.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.2
• /
• pp.204-209
• /
• 2016

The analyses on self-heating effect in 7 nm node non-rectangular Bulk FinFET device were performed using 3D device simulation with consideration to contact via and pad. From self-heating effect simulation, the position where the maximum lattice temperature occurs in Bulk FinFET device was investigated. Through the comparison of thermal resistance at each node, main heat transfer path in Bulk FinFET device can be determined. Self-heating effect with device parameter and operation temperature was also analyzed and compared. In addition, the impact of interconnects which are connected between the device on self-heating effect was investigated.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.6
• /
• pp.576-580
• /
• 2022

Semiconductor devices have evolved from 2D planar FETs to 3D bulk FinFETs, with aggressive device scaling. Bulk FinFETs make it possible to suppress short-channel effects. In addition, the use of low-k dielectric materials as a vacuum gate spacer have been suggested to improve the AC characteristics of the bulk FinFET. However, although the vacuum gate spacer is effective, correlation between the vacuum gate spacer and the short-channel-effects have not yet been compared or discussed. Using a 3D TCAD simulator, this paper demonstrates how to optimize bulk FinFETs including a vacuum gate spacer and to suppress short-channel effects.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.5
• /
• pp.508-517
• /
• 2014

We design and analyze the n-channel junctionless fin-shaped field-effect transistor (JL FinFET) with 10-nm gate length and compare its performances with those of the conventional bulk-type fin-shaped FET (conventional bulk FinFET). A three-dimensional (3-D) device simulations were performed to optimize the device design parameters including the width ($W_{fin}$) and height ($H_{fin}$) of the fin as well as the channel doping concentration ($N_{ch}$). Based on the design optimization, the two devices were compared in terms of direct-current (DC) and radio-frequency (RF) characteristics. The results reveal that the JL FinFET has better subthreshold swing, and more effectively suppresses short-channel effects (SCEs) than the conventional bulk FinFET.

• Journal of IKEEE
• /
• v.19 no.1
• /
• pp.41-44
• /
• 2015

Silicon trench process for bulk fin field effect transistor (finFET) is suggested without using chemical mechanical polishing (CMP) that cause contamination problems with chemical stuff. This process uses thickness difference of photo resistor spin coating and silicon nitride sacrificial layer. Planarization of silicon oxide and silicon trench formation can be performed with etching processes. In this work 50 nm silicon trench is fabricated with AZ 1512 photo resistor and process results are introduced.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.8 no.2
• /
• pp.156-163
• /
• 2008

We proposed a new $p^+/n^+$ gate locally-separated-channel (LSC) bulk FinFET which has vertically formed oxide region in the center of fin body, and device characteristics were optimized and compared with that of normal channel (NC) FinFET. Key device characteristics were investigated by changing length of $n^+$ poly-Si gate ($L_s$), the material filling the trench, and the width and length of the trench at a given gate length ($L_g$). Using 3-dimensional simulations, we confirmed that short-channel effects were properly suppressed although the fin width was the same as that of NC device. The LSC device having the trench non-overlapped with the source/drain diffusion region showed excellent $I_{off}$ suitable for sub-50 nm DRAM cell transistors. Design of the LSC devices were performed to get reasonable $L_s/L_g$ and channel fin width ($W_{cfin}$) at given $L_gs$ of 30 nm, 40 nm, and 50 nm.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.6 no.2
• /
• pp.68-73
• /
• 2006

We propose a damascene gate FinFET with Si nanocrystals implemented on bulk silicon wafer for low voltage flash memory device. The use of optimized SRON (Silicon-Rich Oxynitride) process allows a high degree of control of the Si excess in the oxide. The FinFET with Si nanocrystals shows high program/erase (P/E) speed, large $V_{TH}$ shifts over 2.5V at 12V/$10{\mu}s$ for program and -12V/1ms for erase, good retention time, and acceptable endurance characteristics. Si nanocrystal memory with damascene gate FinFET is a solution of gate stack and voltage scaling for future generations of flash memory device. Index Terms-FinFET, Si-nanocrystal, SRON(Si-Rich Oxynitride), flash memory device.