• Journal of Korea Society of Industrial Information Systems
• /
• v.18 no.5
• /
• pp.59-65
• /
• 2013

Conventional synchronous design circuits cannot only satisfy the timing requirement of the low voltage digital systems, but also they may generate wrong outputs under the influence of PVT variations and aging effects. Therefore, in this paper, a NCL (Null Convention Logic) design as an asynchronous design method has been proposed, where the NCL method doesn't require any timing analysis, and it has a very simple design methodology. Base on the NCL method, a new low power reliable ALU has been designed and implemented using MagnaChip-SKhynix 0.18um CMOS technology. The experimental results of the proposed NCL ALU have been compared to those of a conventional pipelined ALU in terms of power consumption and speed.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.7
• /
• pp.17-26
• /
• 1999

In this paper, Bit selectable and Bi-directional Interface Device is described, which can communicate data with the peripheral devices. Specially, an algorithm of truth-table comparison that synthesizes the pulse-type sequential circuit pulse has been proposed to design the Interrupt Generator, and implemented in designing the Interrupt Register. Also, a description of the asynchronous design method is given to remove the clock skew phenomenon, and the output asynchronous control method which finds the optimal clock and controls all the enable signal of the output pins at the same time is presented. Using this technique interface ports have delay time of less-than 0.7ns.

• Journal of Korea Society of Industrial Information Systems
• /
• v.17 no.4
• /
• pp.17-23
• /
• 2012

Ultra low-power design and energy harvesting applications require digital systems to operate under extremely low voltages approaching the point of balance between dynamic and static power consumption which is attained in the sub-threshold operation mode. Delay variations are extremely large in this mode. Therefore, in this paper, a new low-power logic design methodology using asynchronous NCL circuits is proposed to reduce power consumption and not to be affected by various technology variations in nanoscale MOSFET technology. The proposed NCL is evaluated using various benchmark circuits at 0.4V supply voltage, which are designed using 45nm MOSFET predictive technology model. The simulation results are compared to those of conventional synchrouns logic circuits in terms of power consumption and speed.

• Journal of the Korea Society of Computer and Information
• /
• v.4 no.1
• /
• pp.28-37
• /
• 1999

In this paper. we developed a delay test architecture and test procedure for clocked 5-bit asynchronous counter circuit based on boundary scan architecture. To develope, we analyze the problems of conventional method on delay test for clocked sequential circuit in boundary scan architecture. This paper discusses several problems of delay test on boundary scan architecture for clocked sequential circuit. Conventional test method has some problems of improper capture timing, of same pattern insertion, of increase of test time. We suggest a delay test architecture and test procedure, is based on a clock count-generation technique to generate continuous clocks for clocked input of CUT. The simulation results or 5-bit counter shows the accurate operation and effectiveness of the proposed delay test architecture and procedure.

• Proceedings of the KIEE Conference
• /
• 2007.04a
• /
• pp.267-269
• /
• 2007

PLL(Phase Locked Loop) are widely used circuit technique in modern electronic systems. In this paper, We propose the low voltage and high speed PLL. We design the PFD(Phase Frequency Detector) by using TSPC (True Single Phase Clock) circuit to improve the performance and solve the dead-zone problem. We use CP(Charge Pump} and LP(Loop filter) for Negative feedback and current reusing in order to solve current mismatch and switch mismatch problem. The VCO(Voltage controlled Oscillator) with 5-stage differential ring oscillator is used to exact output frequency. The divider is implemented by using D-type flip flops asynchronous dividing. The frequency divider has a constant division ratio 32. The frequency range of VCO has from 200MHz to 1.1GHz and have 1.7GHz/v of voltage gain. The proposed PLL is designed by using 0.18um CMOS processor with 1.8V supply voltage. Oscillator's input frequency is 25MHz, VCO output frequency is 800MHz and lock time is 5us. It is evaluated by using cadence spectra RF tools.

• Journal of the Korean Solar Energy Society
• /
• v.23 no.3
• /
• pp.29-35
• /
• 2003

Generator for wind power can be either synchronous or asynchronous (induction) types. Induction and synchronous generators behave in a different way when subjected to severe faults. Induction generators does not have an angle stability limit and short circuit in the neighborhood of an Induction generator causes the demagnetization of the machine when the fault is cleared, the voltage raises slowly, while the grid contributes with reactive power to the generator and the magnetic flux recovers. On the other hand in the synchronous generators the recovery of the voltage is immediate, since the excitation of the rotor angle comes from an independent circuit. This paper shows the result of the transient state analysis in the network connected to wind generation system Several case studies have been conducted to determine the effect of the clearing time of a fault on the network stability. It has been found that the critical clearing time can be as low as 61ms in the case of induction generator compared to 370ms in the case of synchronous generator.

• Electronics and Telecommunications Trends
• /
• v.24 no.6
• /
• pp.110-120
• /
• 2009

비동기식 회로는 전역 클록이 없이 모듈끼리의 핸드셰이크 프로토콜에 의해 데이터를 동기화하고, 전송하는 회로로 전역 클록에 기반한 동기식 회로에 비해 전역 클록으로 인한 문제점들, 예를 들면, 타이밍 종결 문제, 전력 소모 문제, 다중 클록 도메인 설계 문제 등에서 이점을 갖는다. 최근에는 이 두 가지 회로의 장점을 모아 서로 다른 클록에 기반한 비교적 작은 규모의 동기식 모듈을 기반으로 모듈끼리의 데이터 전송을 비동기식으로 수행하는 GALS 구조도 많이 연구되고 있다. 본 고에서는 이러한 비동기식 회로를 위한 설계 방식을 설명하기 위해 먼저, 비동기식 회로의 특성과 설계 동향, 설계 방식에 영향을 미치는 핸드셰이크 프로토콜 및 지연 모델을 소개한다. 그리고, 크게 세가지의 설계 방식을 간단한 예제를 통해 설명한다.

• Proceedings of the IEEK Conference
• /
• 2003.07d
• /
• pp.1399-1402
• /
• 2003

Paul Hocker has developed new attacks based on the electric consumption of cryptographic device such as smartcard that performs cryptographic computation. Among those attacks, the Differential Power Analysis(DPA) is one of the most impressive and most difficult to avoid. By analysing the power dissipation of encryption in a device, the secret information inside can be deduced. This paper presents that Advanced Encryption Standard(AES) is highly vulnerable to DPA and readily leaks away all secret keys through the experimental results for DPA. After all, it is required an implementation of the AES algorithm that is not vulnerable to DPA. We also propose countermeasures that employ asynchronous circuit.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.1188-1191
• /
• 2002

A number of studies have recently been published concerning neuron models and asynchronous neural networks. In the case of large-scale neural networks having neuron models, the neural network should be constructed using analog hardware, rather than by computer simulation via software, because of the limitation of the computational power, In this paper, we discuss the circuit structure of a synaptic section model having the spatio-temporal summation of inputs and utilizing CMOS processing.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.14 no.5
• /
• pp.1-6
• /
• 1977

When the input of synchronizer which is used for the purpose of synchronizing the master clock of computer with the interrupt system, a sort of random variable device, is gated with asynchronous intersection of the fall time of the master clock and the risetime oi the interrupt request, synchronizer is drived in Metastable region. This paper is presented circuit analysis of Metastable phenomena and analysis for transient process from metastable point to stable state, and also realities the collect logic with Inverter and open collector methods with a view to improving logic failure caused by the mishappen phenomena.