• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2631-2636
• /
• 2008

The most components and piping of the secondary side of domestic nuclear power plants were manufactured carbon-steel and low-alloy steel. Flow accelerated corrosion leads to wall thinning (metal loss) of carbon steel components and piping exposed to the flowing water or wet steam of high temperature, pressure, and velocity. The feedwater heaters of many nuclear power plants have recently experienced sever wall thinning damage, which increases as operating time progress. Several nuclear power plants in Korea have also experienced wall thinning damage in the shell wall around the impingement baffle. This paper describes the comparisons between the numerical analysis results using the FLUENT code and the experimental results based on down-scaled experimental facility. The experiments were performed based on several types of impingement baffle plates which are installed in low pressure feedwater heater.

• Journal of the Korean Society of Safety
• /
• v.18 no.3
• /
• pp.39-45
• /
• 2003

The failure mode of a pipe due to local wall thinning is increasingly more attention in the nuclear power plant industry. To assess the integrity of locally wall thinned pipe, it is necessary to perform many simulations under various conditions. Because the modeling for locally wall thinned elbow is more complicated than that of straight pipe the efficient modeling method for finite element analysis is necessary. In this study, the more simple efficient modeling method of three-dimensional finite element analysis for locally wall thinned elbow has been suggested and verified. And using the method, the failure mode of local wall thinned elbows that have different thinning lengths and circumferential angles is evaluated. From the results, we concluded that the collapse load of elbows has been decreased by the increase of wall thinning shape factors such as thinning lengths and circumferential angles.

• Steel and Composite Structures
• /
• v.20 no.4
• /
• pp.931-950
• /
• 2016

Ratcheting deformation of pressurized Z2CND18.12N stainless steel $90^{\circ}$ elbow pipe with local wall thinning subjected to constant internal pressure and reversed bending was studied using finite element analysis. Chen-Jiao-Kim (CJK) kinematic hardening model, which was used to simulate ratcheting behavior of pressurized $90^{\circ}$ elbow pipe with local wall thinning at extrados, flanks and intrados, was implemented into finite element software ANSYS. The local wall thinning was located at extrados, flanks and intrados of $90^{\circ}$ elbow pipe, whose geometry was rectangular cross-section. The effect of depth, axial length and circumferential angle of local wall thinning at extrados, flanks and intrados on the ratcheting behaviors of $90^{\circ}$ elbow pipe were studied in this paper. Three-dimensional elastic-plastic analysis with Chen-Jiao-Kim (CJK) kinematic hardening model was carried out to evaluate structural ratcheting behaviors. The results indicated that ratcheting strain was generated mainly along the hoop direction, while axial ratcheting strain was relatively small.

• Journal of Ecology and Environment
• /
• v.32 no.3
• /
• pp.159-165
• /
• 2009

The purpose of this study was to investigate the effects of thinning on fine root biomass and vertical distribution. and litterfall amount in a 50 year old Pinus koraiensis plantation in Chuncheon, Kangwon Province. Fine root (< 2 mm in diameter) biomass ($367\;g/m^2$) in the site 'OC_75', thinning once in 1975, was 68% of those in the site 'CON', no thinning after planting, and in the site 'TC_00', thinning twice in 1975 and 2000. There were no significant differences of dead roots among treatments. Diameter $0{\sim}1\;mm$ roots were vertically decreased only in the TC_00 site. The litterfall was very similar between OC_75 ($5.2\;Mg\;ha^{-1}\;yr^{-1}$) and TC_00 ($4.7\;Mg\;ha^{-1}\;yr^{-1}$), but the composition of litterfall was different: The proportion of leaves and branches was 80% and 13% in OC_75 and 56% and 36% in TC_00, respectively. Reduction of P. koraiensis density by thinning decreased leaf litter as well as fine roots of P. koraiensis, but increased fine roots production by neighboring understory plants offset the reduction of fine roots of P. koraiensis. We suggest that belowground as well as aboveground responses, including both over- and understory vegetation, should be considered to measure the responses of trees in thinned forest ecosystems.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.6
• /
• pp.512-518
• /
• 2008

Guided wave technology is advantageous for fast inspection of pipe wall thinning since the guided wave propagates long distance. In this investigation, the method to evaluate gradual wall thinning in a pipe based on the arrival time delay with magnetostrictive patch transducers is presented. Low frequency A0 Lamb waves were generated and measured by the present transducer and it was applied to arrival time delay measurement experiments on a test pipe having gradual wall thinnings artificially manufactured. From experiments, consistent results that wall thinning increases the arrival time delay of A0 waves were obtained. Consequently, the feasibility of the magnetostrictive patch transducers to evaluate wall thinning was verified.

• Journal of Ocean Engineering and Technology
• /
• v.24 no.4
• /
• pp.38-46
• /
• 2010

The wall thinning phenomenon of pipes was simulated as metal loss due to erosion and corrosion. Such wall thinning defects in the pipes of power plants are a very important safety consideration. In this study, we analyzed wall thinning defects that occurred by weld bead of weld zone of boost pump recirculation pipe. From the results of the analysis of pipe failures, numerical analysis was performed by Fluent v6.3.26 using the standard k-$\varepsilon$ model of the weld bead shape, such as an elliptical or a spherical shape, on the inner wall of the pipe. Using the results obtained, we showed the overlap effect by cavitations corrosion and erosion-corrosion at the bottom of the wall-thinning defect.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.223-226
• /
• 2003

We propose an improvement method for a $\underline{G}ate$ $\underline{OX}ide(GOX)$ thinning at the edge of $\underline{S}hallow$ $\underline{T}rench$ $\underline{I}solation(STI)$, when STI is adopted to Dual Gate Oxide(DGOX) Process. In the case of SOC(System On-a-Chip), the DGOX process is usually used for realizing both a low and a high voltage parts in one chip. However, it is found that the severe GOX thinning occurs from at STI top edge region and a dent profile exists at the top edge of STI, when conventional DGOX and STI process carried out in high density device chip. In order to overcome this problem, a new DGOX process is tried in this study. And we are able to prevent the GOX thinning by H2 anneal, partially SiN liner skip, and a method which is merged a thick sidewall oxide(S/O) with a SiN pull-back process. Therefore, a good subthreshold characteristics without a double hump is obtained by the prevention of a GOX thinning and a deep dent profile.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.11 no.2
• /
• pp.31-39
• /
• 2015

Pipe wall-thinning by flow-accelerated corrosion (FAC) and various types of erosion is a significant and costly damage phenomenon in secondary piping systems of nuclear power plants (NPPs). Most NPPs have management programs to ensure pipe integrity due to wall-thinning that includes periodic measurements for pipe wall thicknesses using ultrasonic tests (UTs). Nevertheless, thinning evaluations are not easy because the amount of thickness reduction being measured is often quite small compared to the accuracy of the inspection technique. U.S. Electric Power Research Institute (EPRI) had proposed Total Point Method (TPM) as a thinning occurrence evaluation method, which is a very useful method for detecting locally thinned pipes or fittings. However, evaluation engineers have to discern manually the measurement data because there are no numerical algorithm for TPM. In this study, numerical algorithms were developed based on non-parametric and parametric statistical method.

• Journal of Magnetics
• /
• v.21 no.1
• /
• pp.57-60
• /
• 2016

Non Destructive Testing (NDT) methods that are capable of detecting the wall thinning and defects through insulation and cladding sheets are necessary. In this study we developed a Pulsed Eddy Current (PEC) system to detect wall thinning of ferro magnetic steel pipes covered with 95 mm thick fiber glass thermal insulator and shielded with aluminum plate of thickness 0.4 mm. In order to confirm the thickness change due to wall thinning, two different sensors, a hall sensor and a search coil sensor were used as a detecting element. In both the cases, the experimental data indicates a considerable change in the detected pulse corresponding to the change in sample thickness. The thickness of the tube was made to change such as 2.5 mm, 5 mm and 8 mm from the inner surface to simulate wall thinning. Fast Fourier Transform (FFT) was calculated using window approach and the results were summarized which shows a clear identification of thickness change in the test specimen by comparing the magnitude spectra.

• Journal of Korean Society of Forest Science
• /
• v.96 no.2
• /
• pp.151-159
• /
• 2007

This study was conducted to investigate the effects of thinning on changes in stand characteristics and understory vegetation in a silvopasture practiced Japanese larch plantation in the Research Forest of Kangwon National University, Korea. Three different thinning intensities (64%, 35%, and control) were applied. Before and after thinning, the understory plant species increased its number from 48 (7 tree species, 7 shrubs species, 28 herbaceous species, and 6 woody climbers) to 100 (11 tree species, 15 shrub species, 67 herbaceous species, and 7 woody climbers). Thinning made plants invade easily on the forest floor, and plot A (325 stems/ha) had much higher number of undersory species than those Of plot B (575 stems/ha) and control plot (1,150 stems/ha). In three years after thinning, understory aboveground biomass (kg/ha) of herbs were 523 for control, 1,230 for plot B, and 1,288 for plot A. The canopy coverage had remarkable influence on the understory biomass production, resulting in relatively small amount of herbage production on control plot. The differences were statistically significant between thinned plots and unthinned plot, but there were no significant differences among the thinned plots (p<0.05).