• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.6
• /
• pp.440-448
• /
• 2009

Facility power-line electromagnetic interference (EMI) filters are used to provide radio frequency(RF) isolation between dedicated power distribution services and noise sensitive local power distribution systems. This type of EMI filters generally needs a high current capacity and, in some special applications, a high insertion loss of a minimum 100dB from 14kHz through 10GHz per MIL-STD 220 is required. This paper deals with an analysis and design of a wideband facility power-line EMI filter with the above requirements. The characteristics of the inductor and capacitor at high frequencies are investigated. The characteristics and design method of the facility EMI filter with a high order LC network are also presented. The prototype filter is finally implemented and its performance is verified from the experimental results.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.1
• /
• pp.43-50
• /
• 2003

전자산업과 전파통신기술이 고도로 발전함에 따른 전파 이용의 증대로 인해 전자파환경 EMI/EMS이 사회적 문제를 야기하고 있다. 이에 따라, CISPR(Comite Internationale Special des Perturbations Radioelectrique), FCC (Federal Communications Commissions) ANSI (American National Standards Institute)등의 기구는 EMI/EMC 대책을 위해 전파환경의 규정을 제정하고 있다. 또한 EMI/EMC 측정을 위한 전파무향실(anechoic chamber)용 전파흡수체는 20 dB 이상의 전파흡수능이 요구된다. 종래의 EMI 측정 주파수 범위는 30 MHz～l,000 MHz 이었으나 1998년 11월, CISPR11은 1 GHz~18 GHz를 추가하는 안을 받아들였다. 본고는 새로운 형태의 다층형 페라이트 전파흡수체를 제안하고 등가재료정수법을 사용하여 광대역 설계를 시도한 것이다.

• Journal of Satellite, Information and Communications
• /
• v.9 no.4
• /
• pp.42-46
• /
• 2014

In this paper, a coil typed electromagnetic band gap (EBG) structure to be inserted in the printed circuit board (PCB) inner layer in order to stabilize the PCB power line is proposed and implemented for global-navigation satellite service (GNSS) with the bandwidth from 1.55GHz to 1.81GHz. From the measurement result of the PCB board including EBG structure, the insertion loss(S21) was measured below about -50dB. From these results, it is expected that the stabilization of power delivery network (PDN) structure in the PCB circuit design should be improved and the preparation to EMI will be effective.

• Journal of electromagnetic engineering and science
• /
• v.11 no.4
• /
• pp.282-289
• /
• 2011

GHz electromagnetic interference (EMI) characteristics are analyzed for a 3dimensional (3D) stacked chip power distribution network (PDN) with through silicon via (TSV) connections. The EMI problem is mostly raised by P/G (power/ground) noise due to high switching current magnitudes and high PDN impedances. The 3D stacked chip PDN is decomposed into P/G TSVs and vertically stacked capacitive chip PDNs. The TSV inductances combine with the chip PDN capacitances produce resonances and increase the PDN impedance level in the GHz frequency range. These effects depend on stacking configurations and P/G TSV designs and are analyzed using the P/G TSV model and chip PDN model. When a small size chip PDN and a large size chip PDN are stacked, the small one's impedance is more seriously affected by TSV effects and shows higher levels. As a P/G TSV location is moved to a corner of the chip PDNs, larger PDN impedances appear. When P/G TSV numbers are enlarged, the TSV effects push the resonances to a higher frequency range. As a small size chip PDN is located closer to the center of a large size chip PDN, the TSV effects are enhanced.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.19 no.3
• /
• pp.137-147
• /
• 2020

This paper proposes printed bow-tie antennas with 3 ~ 5 GHz broadband characteristics were proposed for testing the electromagnetic immunity of automotive electrical components in the 5G frequency band. The antenna get -10 dB bandwidth in the 2.75 ~ 6 GHz frequency band and the broadside radiation pattern with S₁₁ characteristic of -16.2 dB at resonant frequency. In testing electromagnetic immunity in the 5G mobile communication frequency band, the VSWR characteristic remained below 2.1, forming a level of 1 W as proposed by international standards. As a result, it is confirmed that the proposed antenna can be applied to antenna testing for electromagnetic immunity verification in the 5G mobile communication frequency band.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.4
• /
• pp.149-157
• /
• 2015

We investigated the effects of the fabric structure or the kinds of plated metals on the electromagnetic interference shielding effectiveness (EMI SE) by means of electroless plating on polyester fabric. We found that the weight of deposited metal, EMI SE, and flexibility of the conductive fabric for EMI shield is affected by morphology of fabric and structure of fiber. The EMI SE of conductive fabric plated Ni/Cu/Ni by electroless plating method on draw textured yarn (DTY) polyester was in the practically useful range of above 70 dB over a wide frequency range of 10 MHz to 1.0 GHz at the surface resistivity of $0.05{\Omega}/{\square}$. Au or Ag plated conductive fabric by immersion plating method is not able to provide for a good EMI SE.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.6
• /
• pp.900-906
• /
• 2000

The remarkable progress of electronics and radio communications technology has made our life abundant. On the other hand, the countermeasure of EMl/EMC becomes more important socially according to the increased use of electromagnetic waves. It had been required that the absorbing ability of an electromagnetic wave absorber is more than 20 dB, the bandwidth of which is required through 30 MHz to 1,000 MHz for satisfying the international standard about an anechoic chamber for EMl/EMS measurement. From November of 1998, however, the CISPR11 has accepted the extended frequency band to 18 GHz in the bandwidth of EMI measurement. In this paper, we proposed the cut corn type and cylinder type absorbers satisfying the above requirments and carried out broadband design using the equivalent material constants method.

• Journal of electromagnetic engineering and science
• /
• v.1 no.1
• /
• pp.95-99
• /
• 2001

According to the progress of the electronic industy and radio communication technologies, mankind might enjoy its abundant life On the other hand, many social problems such as EMI, and unnecessary electromagnetic wave occur due to the increased use of electromagnetic wave. Therefore, the organiztions such as CISPR, FCC, ANSl,etc. have provided the standard of electromagnetic wave enviroment for the countermeasure of the EMC. It had been required that the absorbing ability of an electromagnetic wave absorber is more than 20 dB, the bandwidth of which is required through 30 MHz to 1,000 MHz for satisfying the international standard about an anechoic chamber for EMI/EMS measurment. From November of 1998, however, the CISPRll has accepted the extended frequency band from 1 GHz to 18 GHz additionally in the bandwidth of EMI measurementent$^{[1]}$ . In this paper, we proposed a new type absorber satisfying the above requirements and carried out broadband design using the equivalent material constants method. Futheremore, the experiments were carried out over the frequency band from 30 MHz to 2 GHz, and hence, the validity of the proposed design theory was confirmed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.2 s.117
• /
• pp.166-176
• /
• 2007

Measurement uncertainty assessment is very important in measurement and calibration. RRL provides antenna calibration services for EMI test. Reliability of EMI test depends on accurate antenna calibration. Antenna calibration results have to be accompanied with measurement uncertainty for its better reliability. In the late of 2005, CISPR issued the CISPR/A/644/C which describes the antenna calibration and measurement uncertainty. In this paper, on the basis of CISPR/A/644/C, we provide the measurement uncertainty values for dipole antenna calibration at the Calibration Test Site(CALTS) of Icheon. The antenna calibration method is 3-antenna height-scanning-averaging method, which measures the free-space antenna factor. We also considered all uncertainty sources that can affect measurement results during calibration.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.872-876
• /
• 2006

This study was made to examine the electromagnetic interference(EMI) shielding effect (SE) of multilayered thin films in which indium-tin oxide(ITO) and Ag were deposited alternately from 3layer to 9 layer on Poly Methyl Meth Acrylate(PMMA) substrate at room temperature using a PF sputtering. We measured optical and electrical characteristics by UV-spectrometer and 4 point probe. The measurement of EMI SE in frequency range from 50MHz to 1.5GHz was performed by using ASTM D4935-89 method. We compared the measured EMI SEs with theoretical simulation data. We obtained relatively low resistivity and high transmittance from the EMI SE multilayers. In this study, we obtain good optical electrical characteristics with a minimun transmittance of about 60% at 550nm wavelength and sheet resistance of $2{\sim}3ohm/sq$., respectivity. Measured EMI SEs were over 50dB and similar to theoretical simulation data.