• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.12
• /
• pp.1-6
• /
• 2008

In this paper, bias control circuit structure have been employed to improve the power added efficiency of the CMOS class-E power amplifier on low input power level. The gate and drain bias voltage has been controlled with the envelope of the input RF signal. The proposed CMOS class-E power amplifier using bias controlled circuit has been improved the PAE on low output power level. The operating frequency is 2.14GHz and the output power is 22dBm to 25dBm. In addition to, it has been evident that the designed the structure has showed more than a 80% increase in PAE for flatness over all input power level, respectively.

• Proceedings of the IEEK Conference
• /
• 2004.08c
• /
• pp.499-502
• /
• 2004

A two-stage Class E power amplifier operated at 2.44GHz is designed in 0.25-$\mu$m CMOS process for Class-l Bluetooth application. The power amplifier employs c1ass-E topology to exploit its soft-switching property for high efficiency. A preamplifter with common-mode configuration is used to drive the output-stage of Class-E type. The amplifier delivers 20-dBm output power with 70$\%$ PAE (power -added-efficiency) at 2-V supply voltage.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.1
• /
• pp.9-15
• /
• 2015

A CMOS band-pass delta-sigma modulator(BPDSM) and cascode class-E power amplifier have been developed CMOS for Class-S power amplifier applications. The BPDSM is operating at 1-GHz sampling frequency, which converts a 250-MHz sinusoidal signal to a pulse-width modulated digital signal without the quantization noise. The BPDSM shows a 25-dB SQNR(Signal to Quantization Noise Ratio) and consumes a power of 24 mW at an 1.2-V supply voltage. The class-E power amplifier exhibits an 18.1 dBm of the maximum output power with a 25% drain efficiency at a 3.3-V supply voltage. The BPDSM and class-E PA were fabricated in the Dongbu's 110-nm CMOS process.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.6
• /
• pp.287-290
• /
• 2006

A class-E CMOS RF(Radio frequency) power amplifier with a 1.8 Volt power supply is designed using $0.25{\mu}m$ standard CMOS technology. To drive the class-E power amplifier, a Class-F RF power amplifier is used and the reliability characteristics are studied with a class-E load network. After one year of operating the power amplifier with an RF choke, the PAE(Power Added Efficiency) decreases from 60% to 47% and the output power decreases 29%. However, when a finite DC-feed inductor is used with the load, the PAE decreases from 60% to 53% and the output power decreases only 19%. The simulated results demonstrate that the class-E power amplifier with a finite DC-feed inductor exhibits superior reliability characteristics.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.1
• /
• pp.114-121
• /
• 2003

In this paper, low voltage and two stage CMOS Class E RF power amplifier for ISM(Industrial/Scientific/Medical) Open Band is presented. The power amplifier operates at 2.4GHz frequency, and is designed and simulated with a 0.35um CMOS technology and HSPICE simulator. The power amplifier is simple structure of two stage Class E power amplifier. The design procedure determing matching network was presented. The power amplifier is composed of input stage matching network, preamplifier, interstage matching network, power amplifier, and output stage matching network. The matching networks of input stage and interstage were constituted by pi($\pi$) type and L type respectively. At 2.4GHz operating frequency, and with a 2.5V supply voltage, the power amplifier delivers 23dBm output power to a 50${\Omega}$ load with 39% power added efficiency(PAE).

• Journal of electromagnetic engineering and science
• /
• v.9 no.1
• /
• pp.32-37
• /
• 2009

Various Class-E CMOS power amplifiers for GSM applications are presented. A stage-convertible transformer for a dual mode power amplifier is proposed to increase efficiency in the low-output power region. An integrated passive device(IPD) process is used to reduce combiner losses. A split secondary 1:2 transformer with IPD process is designed to obtain efficient and symmetric power combining. A quasi-four-pair structure of CMOS PA is also proposed to overcome the complexities of power combining.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.113-117
• /
• 2003

This paper describes the design and the simulation results of the RF CMOS Class-E Power Amplifier for a 2.4GHz ISM band. This circuit is composed two connected amplifiers. where Class F amplifier drives Class E amplifier. The proposed circuit can reduce the total power dissipation of the driving stage and can work with higher efficiency. The power amplifier has been implemented in a standard $0.25{\mu}m$ CMOS technology and is shown to deliver 100mW output power to load with 41% power added efficiency(PAE) from a 2.5V supply.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.335-339
• /
• 2003

This Paper describes the design and the simulation results of the RF CMOS Class-E Power Amplifier for a 2.4GHz ISM band. This circuit is composed two connected amplifiers. where Class F amplifier drives Class E amplifier. The proposed circuit can reduce the total power dissipation of the driving stage and can work with higher efficiency. The power amplifier has been implemented in a standard 0.25$\mu\textrm{m}$ CMOS technology and is shown to deliver 100mW output Power to load with 41％ power added efficiency(PAE) from a 2.5V supply.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.10B
• /
• pp.1475-1481
• /
• 2001

무선 통신을 위한 전력 증폭기를 0.25$\mu\textrm{m}$ CMOS 공정으로 구현하였다. 전력 효율을 증가시키기 위하여 class-E 구조를 사용하여 soft-switching 특성을 활용하였다. Class-E 부하 회로의 DC-feed 인덕터는 유한한 값을 갖도록 하여 RF-choke을 사용하는 경우에 비해 동일한 전력과 공급 전압에 대해 필요로 하는 부하 저항의 크기를 증가시킴으로써 전력 효율을 더욱 증가시킬 수 있었다. 또한 common-gate switching 방법을 사용하여 기존의 switching 방법에 비해 허용되는 공급 전압의 크기를 두배 정도 증가시킬 수 있도록 하였다. 이러한 기법을 사용함으로써 900MHz의 주파수에서 공급 전압이 1.8V일 때 트랜지스터에 아무런 전압 stress를 가하지 않고 0.9W의 전력을 41%의 효율(power added efficiency, PAE)을 가지면서 50Ω 부하에 전달함을 확인하였다.

• Journal of information and communication convergence engineering
• /
• v.6 no.2
• /
• pp.154-157
• /
• 2008

A class-E RF(Radio Frequency) power amplifier for wireless application is designed using standard CMOS technology. To drive the class-E power amplifier, a class-F RF power amplifier is used and the reliability characteristics are studied with a class-E load network. The reliability characteristic is improved when a finite-DC feed inductor is used instead of an RF choke with the load. After one year of operating, when the load is an RF choke the output current and voltage of the power amplifier decrease about 17% compared to initial values. But when the load is a finite DC-feed inductor the output current and voltage decrease 9.7%. The S-parameter such as input reflection coefficient(S11) and the forward transmission scattering parameter(S21) is simulated with the stress time. In a finite DC-feed inductor the characteristics of S-parameter are changed slightly compared to an RF-choke inductor. From the simulation results, the class-E power amplifier with a finite DC-feed inductor shows superior reliability characteristics compared to power amplifier using an RF choke.