• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.137-137
• /
• 2008

In-situ doped polycrystalline 3C-SiC thin films were deposited by APCVD at $1200^{\circ}C$ using HMDS(hexamethyildisilane: $Si_2(CH_3)_6)$) as Si and C precursor, and 0 ~ 100 sccm $N_2$ as the dopant source gas. The peak of SiC is appeared in polycrystalline 3C-SiC thin films grown on $SiO_2$/Si substrates in XRD(X-ray diffraction) and FT-IR(Fourier transform infrared spectroscopy) analyses. The resistivity of polycrystalline 3C-SiC thin films decreased from 8.35 $\Omega{\cdot}cm$ with $N_2$ of 0 sccm to 0.014 $\Omega{\cdot}cm$ with 100 sccm. The carrier concentration of poly 3C-SiC films increased with doping from $3.0819\times10^{17}$ to $2.2994\times10^{19}cm^{-3}$ and their electronic mobilities increased from 2.433 to 29.299 $cm^2/V{\cdot}S$, respectively.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.109.1-109.1
• /
• 2012

본 연구에서는 co-sputtering을 통한 $WO_3$와 $In_2O_3$ 타겟을 사용하여 $WO_3$ 파워에 따른 Tungsten(W)-doped $In_2O_3$ (IWO) 투명 전극의 전기적, 광학적, 구조적 특성을 연구하고 이를 활용한 유기태양전지(Organic Photovoltaics; OPVs)의 특성을 분석하였다. Tungsten의 doping 농도는 $WO_3$에 인가되는 Radio-frequency (RF) power를 5~30 W 까지 변화시켜 조절하였으며, Rapid Thermal Annealing (RTA) 후 열처리 공정을 통해 IWO 박막의 전기적, 광학적, 구조적 특성을 분석하였다. Hall measurement 및 UV/Vis spectrometry 분석을 통하여 가시광선 영역에서 80% 이상의 높은 투과율, $48\;cm^2\;V^{-1}\;s^{-1}$의 홀 이동도, 20 ${\Omega}/{\Box}$ 이하의 낮은 면저항과 $3.2{\times}10^{-4}\;{\Omega}-cm$의 비저항 값을 나타내었다. 최적화된 IWO 박막을 이용한 OPV 셀 특성은 fill factor(FF): 61.59 %, short circuit current($J_{SC}$): 8.84 $mA/cm^2$, open circuit voltage($V_{OC}$): 0.60 V, efficiency(PCE): 3.27 %로 ITO로 제작된 OPV 샘플과 비교하였을 때 ITO를 대체할 수 있는 고이동도의 새로운 투명 전극 재료로서의 가능성을 확인하였다.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.3 no.2
• /
• pp.1-4
• /
• 1999

The Helmholtz equation is very important in physics and engineering. However, solution of the Helmholtz equation is in general known as a very difficult phenomenon. For if the ${\omega}$ is negative, the FDM discretized linear system becomes indefinite, whose solution by iterative method requires a very clever preconditioner. In this paper we assume that ${\omega}$ is nonnegative, and determine the optimal ${\rho}$ parameter for the three dimensional ADI iteration for the Helmholtz equation. The ADI(Alternating Direction Implicit) method is also getting new attentions due to the fact that it is very suitable to the vector/parallel computers, for example, as a preconditioner to the Krylov subspace methods. However, classical ADI was developed for two dimensions, and for three dimensions it is known that its convergence behaviour is quite different from that in two dimensions. So far, in three dimensions the so-called Douglas-Rachford form of ADI was developed. It is known to converge for a relatively wide range of ${\rho}$ values but its convergence is very slow. In this paper we determine the necessary conditions of the ${\rho}$ parameter for the convergence and optimal ${\rho}$ for the three dimensional ADI iteration of the Peaceman-Rachford form for the real Helmholtz equation with nonnegative ${\omega}$. Also, we conducted some experiments which is in close agreement with our theory. This straightforward extension of Peaceman-rachford ADI into three dimensions will be useful as an iterative solver itself or as a preconditioner to the the Krylov subspace methods, such as CG(Conjugate Gradient) method or GMRES(m).

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.4
• /
• pp.267-271
• /
• 2011

The insulating characteristics and temperature rise behaviors of porcelain suspension insulators were investigated. The testing insulators had used in the distribution systems normally and were sampled. Firstly, leakage current was measured and its impedance was calculated. The leakage current of good insulators is 0.2 mA and its impedance is 66 $M{\Omega}$. The worse insulators have lower impedance and the insulators having below 15 $M{\Omega}$ take place flashover at the high frequency voltage flashover test. Secondly, the temperature rise characteristics were analyzed depending on leakage current and its impedance. Surface temperature of insulators was measured for 30 minutes and until its saturation after voltage was applied. The temperature rise of insulators having 15 $M{\Omega}$ is about $14.5^{\circ}C$ above the ambient temperature. Lastly, the heating behaviors of 3 insulators in a string was analyzed. Any insulator in the string does not generate heat so far as it has at least one sound insulator. On the other hand, all the insulators in the string are bad if the string have any heating insulator.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.5
• /
• pp.169-172
• /
• 2009

The ZnO/CuSn/ZnO (ZCSZ) multilayer films were deposited on polycarbonate substrates using reactive RF and DC magnetron sputtering. The thickness of each layer was 50 nm/5 nm/45 nm, respectively. The ZCSZ films showed a sheet resistance of $44{\Omega}$/Sq, which was an order of magnitude lower than that indium tin oxide (ITO) films. Although the ZCSZ films had a CuSn interlayer that absorbed visible light, both films had similar optical transmittances of 74% in the visible wavelength region. The figure of merit of the ZCSZ films was $1.0{\times}10^{-3}{\Omega}^{-1}$ and was greater than the value of the ITO films, $1.6{\times}10^{-4}{\Omega}^{-1}$. From the X-ray diffraction (XRD) analysis, the ITO films did not show any diffraction peaks, whereas the ZCSZ films showed diffraction peaks for the ZnO (100) and (002) phases. The hardness of the ITO and ZCSZ films were 5.8 and 7.1 GPa, respectively, which were determined using nano-indentation. From these results, the ZCSZ films exhibited greater optoelectrical performance and hardness compared to the conventional ITO films.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.6 no.3
• /
• pp.101-110
• /
• 2007

This study has designed a circular polarization antenna for UHF bandwidth RFID reader. As a result of performance test of the antenna designed it is found that return loss (S11) is about -45.529dB at 914MHz, which is relatively small, and antenna gain is about 6.09dBi. It has also been confirmed that $50{\Omega}$ impedance matching is about $50.48{$\Omega}$ and it can be applied to every RFID reader. Therefore, the antenna is designed to have higher gain of circular polarization by improving reception, which is one of the most important parameters of RFID reader and is expected to be extensively used to recognize multi-tag in the distance.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.6 s.67
• /
• pp.58-63
• /
• 2005

The estimation of springing responses for recent ships is carried out, and application to a ship design is described. To this aim, springing effects on hull girder were re-evaluated, including non-linear wave excitations and torsional vibrations of the hull. The Timoshenko beam model was used to calculate stress distribution on the hull girder, using the superposition method. The quadratic strip method was employed to calculate the hydrodynamic forces and moments on the hull. In order to remove the irregular frequencies, we adopted 'rigid lid' on the hull free surface level, and addedasymptotic interpolation along the high frequency range. Several applications were carried out on the following existing ships: The Bishop and Price's container ship, S-175 container ship, large container, VLCC, and ore carrier. One of them is compared with the ship measurement result, while another with that of the model test. The comparison between the analytical solution and the numerical solution for a homogeneous beam-type artificial ship shows good agreement. It is found that Most springing energy comesfrom high frequency waves for the ships having low natural frequency and North Atlantic route etc. Therefore, the high frequency tail of the wave spectrum should be increased by $\omega$$\^{-3}$ instead of $\omega$$\^{-4}$ or $\omega$$\^{-5}$ for the springing calculation.

• Proceedings of the KIEE Conference
• /
• 2005.11a
• /
• pp.48-50
• /
• 2005

As technology is developed, customers want to use many functions in one system. Manufacturers want to reach the customer's needs, make systems more small, thin, light-weight. To make them real, it is necessary to make components to be small and thin. But components of power stage are big, thick and heavy-weighted yet. especially power inductor is the most significant component. This paper proposed a novel chip-type power inductor I-type inductor. Inductor that proposed has 3225-size, 5.6uH and 1.3A of max saturation current. And it has $R_{DC}$ of $0.25{\Omega}$ which is smaller than $0.45{\Omega}$ of chip-type inductor and $0.9{\Omega}$ of coil-type inductor.

• Journal of Mechanical Science and Technology
• /
• v.15 no.3
• /
• pp.366-373
• /
• 2001

A numerical analysis of shock wave/boundary layer interaction in transonic/supersonic axial flow compressor cascade has been performed by using a characteristics upwind Navier-Stokes method with various turbulence models. Two equation turbulence models were applied to transonic/supersonic flows over a NACA 0012 airfoil. The results are superion to those from an algebraic turbulence model. High order TVD schemes predicted shock wave/boundary layer interactions reasonably well. However, the prediction of SWBLI depends more on turbulence models than high order schemes. In a supersonic axial flow cascade at M=1.59 and exit/inlet static pressure ratio of 2.21, k-$\omega$ and Shear Stress Transport (SST) models were numerically stables. However, the k-$\omega$ model predicted thicker shock waves in the flow passage. Losses due to shock/shock and shock/boundary layer interactions in transonic/supersonic compressor flowfields can be higher losses than viscous losses due to flow separation and viscous dissipation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.9
• /
• pp.1802-1811
• /
• 1994

In this paper, the corrugated horn antenna used in the reflector feed horn of satellite is analyzed using the modal expansion method. The modal expansion method is represented by the summations of modals at each point so the exact prediction of field and phase patterns can be obtained. The least number of iterations to compute field patterns is proposed. By using this number. calculation of accurate near and far field patterns without comsuming a lot of computational effort is available. Three kinds of corrugated horn antenna is designed to verify the method and experimented. The VSWR of designed frequency is from 1.04 to 1.1. The input impedance is nearly matched to $50\Omega$.