In this paper, we propose a method that applies Vector Fitting (VF) technique to the equivalent circuit model for RF passive components. These days wireless communication system is getting smaller and smaller. So EMI/EMC is an issue in RF. We can solve PI/SI (Power Integrity/Signal Integrity) that one of EMI/EMC problem apply IFFT for 3D EM simulation multiple with input signal. That is time consuming task. Therefore equivalent circuit model using RF passive component is important. VF schemes are implemented to obtain the rational functions. S parameters of the equivalent circuit model is compared to those of EM simulation in case of the microstrip line structure.

This paper presents a new dynamically adaptable polling scheme for efficient support of real-time traffic over an IEEE 802.11 wireless LAN network. The poll scheduling plays an important role in IEEE 802.11 PCF. However, the current version of the polling list management scheme proposed in the IEEE 802.11 standard is inefficient when a variable number of mobile stations have variable packets to transmit. If Point Coordinator has an exact information on the station status, it is possible to efficiently perform polling. In this paper, we suggest an adaptable polling scheme to meet requirements of the stations. In our scheme, each station transmits packets including a piggyback information to inform that it wants to receive a poll in the next polling duration. Simulation results indicate that our scheme may reduces the packet discard ratio and real-time packet transfer delay.

In this paper, We play it for the purpose of study about the power amplifier which applied DGS and adaptive bias circuit structure to general Doherty amplifier for the efficiency of a RF power amplifier and a linearity improvement in the WiBro band. As for the IMD3, 3.4dBc was improved with -26.3dBc when we did the measurement result existing Doherty power amplifier and comparison of the Doherty power amplifier which applied an adaptive bias circuit and the DGS which proposed in this paper, and the mean power efficiency verified what was increased in 37%. Also, we were able to know PAE of 36.6% with output power 34.0dBm in P1dB when magnitude of an input signal was 25.6dBm. we did 6dB back off in output P1dB in order to confirm the ACPR which was a nonlinear characteristic and measured the ACPR. we showed the -34.55dBc which was a value of -34.5dBc or below in the 4.77MHz off-set that was a transmission standard. Therefore, we were able to know that we were satisfied with a spectrum mask standard.

The conventional channel selection method for a ZigBee communication network basically detects the energy values in all channels. In the ISM band, no license is required to use channels in this band, so there may exist various interference factors in this band. It is well known that WLAN is the major interference factor degrading the performance of ZigBee in the ISM band. In this paper, we propose an efficient channel selection algorithm which uses the pattern of two types of WLAN channel uses as the a priori information of IEEE 802.11 band IEEE 802.11g. By using the proposed algorithm, we may save the time required to select channels for the ZigBee communications.

In this paper, we show the implementation of the low-cost RF transceiver module for parking control system. Super regenerative receiver scheme was adopted for this module due to its simplicity, low-cost, low power consumption and small number of components to improve reliability of the systems. For improving communication error rate by collision and in-band noise, dual-channel hopping scheme was adopted. Testing prototypes under the environment of simultaneous transmissions, we verified that the designed scheme is able to improve the success rate of data transmission of wireless parking control system cost effectively.

In this paper, the type of inkjet heads and the control of head of inkjet printer are surveyed. The electronic parts of inkjet printer are composed of main- board and sub-board. The inkjet head is controlled by using these boards. The results from silver ink jetting experiment are given. The results show that the implemented inkjet system can give a satisfactory performance.

In this paper, we propose a 4-wire type driving circuit for resistive touch panel which was manufactured at the lab. The circuit is designed by using the touch panel controller ADS7846 and AVR microcontroller board. The test result shows that the designed circuit can give and transmit the position information of touch panel to the computer.

This paper presents a self-sustaining system, and an effective method in enhancing overall energy efficiency. The proposed system consists of the two major nodes: a slave node, which contains the environment information (e.g., temperature, humidity, etc.); and a master node, which communicates with the slave nodes, and transmit the slave node's information to users. All slave nodes are under control of the master node. Each slave node uses two power sources: the piezoelectric power generator (PPG); and the continuous wave from the master node. The paper highlights the basic operational principle, each node's specifications, and experimental data for performance verification. The two nodes successfully communicate each other in a range of 3.3m (maximal range), where the user's computer is wired the master node.