Injection molding is a very important industrial process for the manufacturing of plastics objects. During an injection molding process of composites, the fiber-matrix separation and fiber orientation are caused by the flow of molten polymer/fiber mixture. As a result, the product tends to be nonhomogeneous and anisotropic. Hence, it is very important to clarify the relations between separation orientation and injection molding conditions. So far, there is no research on the measurement of fiber orientation using image processing. In this study, the effects of fiber content ratio and molding condition on the fiber orientation-angle distributions are studied experimentally. Using the image processing method, the fiber orientation distribution of weld-line in injection-molded products is assessed. And the effects of fiber content and injection mold-gate conditions on the fiber orientation are also discussed.

The important function of Ball-Stop part is to operate power shift using suitable pneumatic force for vehicle with more than 5 ton when a driver changes gear. In this paper, we have applied the concept of the DFSS(Design for Six Sigma) to robust design of Ball-Stop part. First, we have found the control factors which could mainly influence the performance of the Ball-Stop part. The simulations of contact between head and detent pin was performed to evaluate effect of control factors according to DOE(Design of experiment) by using $ADAMS^{(R)}$. Finally, we have obtained optimal levels of each factors using $MINITAB^{(R)}$. Through the comparison of the result of optimized design with one of inintial design, we have verified the usefulness of DFSS method which can be applied to robust design of mechanical systems.

Recently, atomic force microscope(AFM) with suitable tips is being used for nano fabrication/nanometric machining purposes. In this paper, acoustic emission(AE) was introduced to monitor the nanometric machining of brittle materials(silicon) using AFM. In the experiments, AE responses were sampled, as the tip load was linearly increased(ramped load), to investigate the machining characteristics during a continuous movement. By analyzing the experimental results, it can be concluded that measured AE energy is sensitive to changes in the mechanism of material removal including the ductile-brittle transition during the nanometric machining. The critical depth of cut value for the transition is evaluated and discussed.

Detection of exit burr is very important in manufacturing automation. In this paper, acoustic emission(AE) was used to detect the burr formation during milling. By using wavelet transformation, AE data was compressed without unnecessary details. Then the transformed data were used as selected features (inputs) of a back-propagation artificial neural net. In order to validate the proposed scheme, the wavelet based ANN results were compared with cutting condition(cutting speed, feed, depth of cut, etc.) based ANN results.

As the complexity of engineering design environment has been increased, it becomes difficult to exchange design data among design support systems. The purpose of this paper is to develop the XML-based Generalized Mechanical Data Exchange Formats(GMDEF) independent of specific mechanical element and to improve the interoperability of them using ontology, in order to integrate diverse design data and facilitate communication between design support systems. GMDEF consists of PartDoc and AssemblyDoc. PartDoc represents the information of a single part. AssemblyDoc represents the relation of parts composing an assembly. GMDEF is validated by GMDEF Schema. GMDEF Schema consists of separated XML Schemas and has flexible architecture to facilitate extension. The ontology is applied to GMDEF Schema to share and reuse vocabularies of specific mechanical elements.

A computer-controlled micro tribotester has been developed to investigate the friction and wear characteristics of thin coatings, which can be applied to silicon-based materials. In the developed system, a step motor gives a reciprocating movement and an electromagnet applies a load between a ball and a plate specimen. Test results confirmed that the application of load in the range of $0.03{\sim}1.8N$ and with a sliding speed of $4.44{\sim}7.70mm/s$ was successfully accomplished. Advantages of the developed micro tribotester are: (1) realization of micro load and displacement applicable to micro electromechanical systems(MEMS) using DC motor and electromagnet (2) continuously variable load and reciprocating speed; and (3) high reliability, which allows for unattended use for long periods.

Recently, demand the ultra precision product which is increasing rapidly is used extensively frontier industry field such as semi-conductor, computer, aerospace, precision machine. Ultra precision processing is the portion that is very needed to NT in the field of mechanical engineering. The latest date, together with radical advancement of electronic and photonics industry, necessity of ultra precision processing is on the increase for the manufacture of various kernel parts those are connected with these industrial fields. Specially, require motion accuracy of high resolution of nm order in stroke of hundreds millimeters according as diameter of processing object great and processing accuracy rises. In this case ,the response speed absolute delay because inertial mass of moving part is very large. Therefore, real time motion error compensation becomes very hardly. In this paper, we used ultra precision cutting unit(UPCU) to cope such problem. a UPCU is designed and tested to obtain sub-micrometer from accuracy in diamond turning of flat surfaces. The thermal growth spindle error is compensated for real time using a UPCU driven by piezoelectric actuator along with a laser encoder displacement sensor.

This study deals with the friction welding of SM25C and SCNCrM-2B; The friction time was variable conditions under the conditions of spindle revolution 2,000rpm, friction pressure of 100MPa, upset pressure of l50MPa, and upset time of 4.0 seconds. Under these conditions, the microstructure of weld interface, tensile fracture surface and mechanical tests were studied, and so the results were as follows. 1. When the friction time is 2.0 seconds, the tensile strength of friction welds was 874MPa, which is around as much as 117% of the tensile strength of base metal(SM25C), the bending strength of friction welds was 1,354MPa, which is around as much as 108.9% of the bending strength of base metal(SM25C). 2. At the same condition, the maximum vickers hardness was Hv443 at SCNCrM-2B nearby weld interface, which is higher Hv20 than condition of the friction time 0.5 seconds. 3. The results of microstructure analysis show that the structures of two base materials have fractionated and rearranged along a column due to heating and axial force during friction, which has affected in raising hardness and tensile strength.

Various kinds of rapid prototyping processes are available, such as stereo-lithography apparatus(SLA), fused deposition modeling(FDM), selective laser sintering(SLS), 3 dimensional printing(3DP), and laminated object manufacturing(LOM). In this study, benchmark tests are carried out to obtain detailed informations about surface roughness and mechanical properties of those parts. Although the patterns and roughness averages of part surface are dependent on the surface direction, the roughness of SLA part is the best and that of FDM or 3DP part is the worst. It is shown that FDM part has an advantage in impact strength, SLS(or EOS) part in compressive strength, and LOM part has an advantage in tensile strength and heat resistance, but the change of building direction in FDM and LOM processes severely weakens the tensile and impact strengths.

This research presents the reliability analysis of the pneumatic actuator within the tape feeder that is used to transfer the correct force to linked parts during l.0E+7 cycles. First, the degradation analysis for thrust and air leakage is executed to obtain the failure data of a product based on its performance over time. Second, once the parameters has been calculated using the weibull 2-parameter distribution and MLE(Maximum Likelihood Estimation), information related to life such as reliability, failure rate, probability density function is estimated. Finally, MTTF(Mean Time To Failure) and $B_{10}$ life of actuators are calculated. MTTF means the mean life at the confidence level and $B_{10}$ life refers to the time by which 10% of the product would fail. In this study, failure causes and solutions are examined using the reliability analysis.

This paper present the optimal cleaning condition of the out-hull preprocessing robot by Taguchi method in design of experiments. A $L_8(2^4)$ orthogonal array is adopted to study the effect of adjustment parameters. The adjustment parameters consist of robot speed, motor torque, motor speed and tool angle. And the quality feature is selected as surface roughness of sheet metal. Taguchi analysis is performed in order to evaluate the effect of adjustment parameters of the quality feature of cleaning process by $Minitab^{(R)}$.

This paper describes the steady flow characteristics due to PDA and tumble control valve in combustion chamber. We also investigated the flow inclination angle defined as the inverse tangent of non-dimensional rig tumble(NRT) devided by non-dimensional rig swirl(NRS) to find dominant flow direction. So we adapted two different types of PDA valve(port deactivation valve) to strengthen a swirl flow. The in-cylinder swirl flow different tendency between with/without PDA valve. It might be thought to be affected by swirl flow. We could find that tumble ratio and swirl ratio is different by PDA valve. The comparison are taked account of the swirl, the tumble ratio comparison in same mass flow rate. As a result, PDA valve is better than tumble control valve both in steady flow condition and swirl, tumble ratio. The data from present study are available for design of engine as the basic data.

At present, industry and researchers are looking for ways to reduce the use of lubricants because of ecological and economical reasons. Therefore, metal cutting is to move toward dry cutting or semi-dry cutting. One of the technologies is known as MQL(Minimum Quantity Lubrication) machining. This research presents an investigation into MQL machining with the objective of deriving the optimum cutting conditions for the turning process of SM4SC. To reach these goals several finish turning experiments were carried out, varying cutting speed, feed rate, oil quantity and so on, with MQL and flood coolant. The surface roughness and cutting force results of tests were measured and the effects of cutting conditions were analyzed by the method of Analysis of Variance(ANOVA). From the experimental results and ANOVA, this research proposed optimal cutting conditions to improve the machinability in MQL turning process.

This paper presents an integrated machining error compensation method based on PNN(Polynomial Neural Network) approach and inspection database of OMM(On-Machine-Measurement) system. To efficiently analyze the machining errors, two machining error parameters are defined and modeled using the PNN approach, which is used to determine machining errors for the considered cutting conditions. Experiments are carried out to validate the approaches proposed in this paper. In result, the proposed methods can be effectively implemented in a real machining situation, producing much fewer errors.

In this paper, for the purpose of investigation the acoustic emission(AE) behaviors during resistance spot welding process and tension test of spec steels. As the results present the resistance spot welding method that can get suitable welding qualities or structural integrity estimating method. The resistance spot welding process consists of several stages: set-down of the electrodes; squeeze; current flow; forging; hold time; and lift-off. Various types of AE signals are produced during each of these stages. For tensile-shear test and cross tensile test in resistance spot welded specimens, fracture pa 야 ems are produced: tear fracture; shear fracture; and plug fracture. Tensile-shear specimens strength appeared higher than cross tensile specimens one. In case of tensile-shear specimen happened tear fracture that crack happens in most lower plate. Also, in case of cross tensile specimens, upper plate and lower plate are detached perfect fracture was exposed increases a little as acting force is lower than ordinary welding condition. Therefore, the structure which is combined by resistance spot welding confirmed that welding design must attain so that shear stress may can interact mainly.