In order to determine the wear Properties of PECVD ceramic coatings, wear process was evaluated using the coated pin of Falex Tribosystem. Coating materials deposited wear the TiC, TiN and Ti(CN). An experimental process was established to determine the tribological characteristics of friction and wear behavior under the variation of applied load, temperature and sliding distance by the Falex test machine. The experimental results indicate that TiN coating compared with TiC coating on e materials have e excellent friction and wear characteristics. However TiC coating compared i친 TiN coatings have a low friction coefficient with steel and good thermal stability, and Ti(CN) has the excellent anti-wear properly as well as the superiority of extreme pressure property. Compound coating compared wi simple coatings show improved tribological characteristics.

This study proposes the construction of 2-3 dimensional attractor system for cutting characteristics evaluation of metals. Also this paper aims to find the optimal cutting conditions of diamond turning machine by measuring surface form and roughness to perform the cutting experiment of metals, which are aluminum, with diamond tool. As well, according to change cutting conditions such as feed rate, using diamond turning machine to perform cutting processing, by measuring cutting force and surface roughness and according to cutting conditions the aluminum about cutting properties. Trajectory changes in the attractor indicated a substantial difference in attractor characteristics. Constructed 2-3 dimensional attractor system in this study can be used for cutting characteristics evaluation of metals.

This paper describes a dwell time calculation algorithm for polishing tool path generation in the small toot polishing process of the axis-symmetrical lens. Generally dwell time control in the polishing machines means that small polishing tool stays for a dwell time at the specific surface position to get the expected polishing depth. Polishing depth distribution on an aspherical lens surface consists of the superposition of the local polishing depth at the each dwell position. Therefore, tool path generation needs each dwell time together with tool positioning data during the polishing tool movements on the aspherical lens surface. The linear algebraic equation of removal depth removal matrix and dwell time is formulated. Parametric effects such as the dwell d interval are simulated to validate the dwell time calculation algorithm.

From on the machining center cutting work of 5534, the characteristics such as spindle speed and feed speed fir the third point height, average spacing of roughness peaks, bearing ratio, center line average, ten point height. experiments is roughness for sampling length determine to measuring length of cutting feed speed 200, 400, 600, 800mm/min and spindle speed 800, 1000, 1200, 1400rpm. Third point height is spindle speed with most suitable cutting condition 1000rpm. Third point height is feed speed with most suitable cutting condition 400mm/min. Average spacing of roughness peaks are spindle speed with most suitable cutting condition feed speed increased to average spacing of roughness Peaks are increased. Spindle speed increased to average spacing of roughness peaks are decreased. Bearing ratio is spindle speed with feed speed increased to bearing ratio decreased. Center line average is spindle speed with most suitable cutting condition at 1200rpm feed speed with most suitable cutting condition at 200mm/min to cutting foe roughness suddenly decreased. Ten point height is spindle speed with most suitable cutting condition 1200rpm at ten point height cutting face roughness to decreased and feed speed with most suitable cutting condition 800mm/min at ten point height cutting face roughness to decreased.

This paper presents the optimization of expanding velocity for tube expanding process in the manufacturing of a heat exchanger. In specific, the expanding velocity has a great influence on the performance of a heat exchanger because it is a key variable determining the quantity of tube expending at assembly stage as well as a key Parameter determining overall production rate. The simulation showed that the genetic algorithm used in this paper resulted in the optimal tube expanding velocity by performing the following series of iteration; the generation of arbitrary population for tube expanding parameters, consequently the generation of tube expanding velocities, the evaluation of tube expanding quantity using the pre-trained data of plastic deformation by means of a neural network and finally the generation of next population using a penalty faction and a Roulette wheel method.

ZnO epilayer was synthesized by the pulsed laser deposition(PLD) process on Al$_2$O$_3$ subsorte after irradiating the surface of ZnO sintered pellet by ArF(193nm) excimer laser. The epilayers of ZnO were achieved on sapphire(A1203) substrate at the 境mperature of 400$^{circ}$C. The crystalline structure of epilayer was investigated by the Photoluminescence and double crystal X-ray diffraction(DCXD). The carrier density and mobility of ZnO epilayer measure with Hall effect by van der Pauw mothod are $8.27\times$1016cm$^{-3}$ and 299 cm$^{2}$/V$\cdot$s at 293 K respectively, The temperature dependence of the energy band gap of the ZnO obtained from the absorption spectra was well described by the Varshni's relation, E$_g$(T)= 3.3973 eV - ($2.69\times$ 10$^{-4}$ eV/K)T$^{2}$/(T + 463K). After the as-grown ZnO epilayer was annealed in Zn atmospheres, oxygen and vaccum the origin of point defects of ZnO atmospheres has been investigated by the photoluminescence(PL) at 10K. The native defects of V$_{Zn}$, V$_{O}$, Zn$_{int}$, and O$_{int}$ obtained by PL measurements were classified as a donor or acceptor type. In addition we concluded that the heat-treatment in the oxygen atmosphere converted ZnO thin films to an optical p-type. Also, we confirmed that vacuum in ZnO/Al$_2$O$_3$ did not firm the native defects because vacuum in ZnO thin films existed in the form of stable bonds.

Micro duplex stainless steel is used to denote a fine scale two-phase micro structure consisting austenite and firrite. The development of this structure was done by proper thermo-mechanical processing. The objective of present investigation is to study creep characteristics of this alloy. Since we have little design data about the W behaviors of the alloy. An apparatus has been designed and built fir conducting creep tests under constant load conditions. A series of creep tests on them have been performed to get the basic design data and life prediction of micro duplex stainless steel products and we have gotten the 1311owing results. First the stress exponents decrease as the test temperatures increase. Secondly, the creep activation energy Gradually decreases as the stresses become higher. Thirdly, the constant of Larson-Miller Parameters on this alloy is estimated as about 5. Last, the fiactographs at the creep rupture show both the ductile and brittle fracture modes according to the creep conditions.

The theodolite system consists of two theodolites, a scale bar and a target bu. A measurement accuracy of theodolite system is affected by a measurement distance of each equipment. This study was performed fir measuring an accuracy when the distance from theodolite to scale bar was changed 2~ 6 m on two theodolites distance 3 a The results showed thai the measurement accuracy could be $\pm$0.021 mm when the distance from theodolite to target was 2,3 and 6 n Specially, it was found that the maximum measurement accuracy was 10.017mm on theodolite collimation distance 3m and the distance 4 m of the theodolite and scale bar.

The machining Parts must be Produced within the specification of drawing and those will be able to meet faction and efficiency. At that time, it is very important not only precision machine and machining technique but also the measurement technique. So, the improvement of measurement technique is to be joined together at once with improvement of machining technique. Finally, the quality and value of the parts are decided by precision measurement. This paper aims to study on the measurement uncertainty when the machined parts are inspected with 3-dimensional coordinate measuring machine. The objectives remove an error of measurement and remove a quality of mass products.

The objective of this study is structural analysis and modal analysis of treadmill roller. A 3D finite element model is implemented to calculate the stress, strain and natural frequency for treadmill roller In order to analyses treadmill roller, many variables such as load condition, boundary condition, weight condition and resonance are considered. Natural frequency of treadmill is compare to motor revolution.

Since the use of CFC and HCFC refrigerants is to be restricted due to the depletion of ozone layer, this experiment applies the $NH_{3}$ gas to study the performance characteristics from the superheat control for improving the energy efficiency. The experiments are carried out for the condensing pressure of refrigeration system from 1500kPa to 1600kPa by 50kPa and for degree of superheat from $0^{circ}$ to $1^{circ}$ by $10^{circ}$ at each condensing pressure. As a result of experiment, 1) As degree of superheat increased, evaporating pressure of the compressor decreased so equilibrium temperature decreased. And specific volume of refrigerant vapors increased so refrigerant mass flow and heat load of the evaporator decreased. 2) An influence of change of condensing pressure on heat load of the evaporator was insignificant. 3) With the identical degree of superheat, change of compressed temperature was insignificant according to each condensing pressure, so there was little change in enthalpy.4) when the degree of superheat is $0^{circ}$C at each condensing pressure, the refrigeration system has the hi띤est performance.

Recently the needs of high reliable substances of high strength and high ductility are gradually increased with the development of aerospace industry. The characteristics of maraging steel has high ductililty, formability, corrosion resistant and high temperature strength and is easy to fabricate, weld and treat with heat, and maintain an invariable size even after heat treatment. e steels are furnished in the solution annealed condition and they achieve full properties through martensitic precipitation aging a relatively simple, low temperature heat treatment. As is true of the heat treating procedures, aging is a time/temperature dependent reaction. Therefore, the objective of this stud)'was consideration of fatigue characteristics according as Nb(niobium) content and time/temperature of heat treatment change. Also the stress analysis, fatigue lift, and stress intensity factor were compared with experiment results and FEA(finite element analysis) result. The maximum ftresses of)( Y, and Z axis direction showed about $2.12\times$10$^{2}$MPa, $4.40\times$10$^{2}$MPa and $1.32\times$10$^{2}$MPa respectively. The fatigue lives showed about $7\%$ lower FEA result than experiment result showing almost invariable error every analyzed cycle. Stress intensity factor of the FEA result was lower about $3.5~ 10\%$ than that of the experiment result showing that the longer fatigue crack ten添 the hi인or error. It considered that the cause for the difference was the modeled crack tip having always the same shape and condition regardless of the crack growth.

A mirror cam mechanism a kind of conjugate cam mechanism consists of two cams, two rollers, and two links. Since profiles of two mirror cam are identical, a simultaneous machining of two cams is achievable. Some machining errors on cam profiles do not result in the internal acting force, which often causes problems in high speed cam mechanism between two links. Also, since angular accelerations of two links are same, the internal acting force by the difference of the angular accelerations does not occur in the mechanism. Thus the mirror cam mechanism is very useful in high speed machinery. This paper studies a design method as well as a machining method, and develops an exclusive CAD/CAM software for mirror cam profiles. The developed CAD/CAM software is applied to a typical mirror cam mechanism and a mock-up equipment is built in order to test the machinism mirror cm. Experimental investigations show that the contact between cam surface and roller surface according to cam rotation agrees well with the simulation on the developed CAD/CAM software.

A feasibility study was performed to see the welding possibility of dissimilar thin-plat materials. These materials were welded for finding the optimum welding condition and evaluating the soundness of welding zone. The welding was attempted under the condition of laser power 500~600w, Pulse width 1.0~2.5ms and frequency 11~18Hz. In this study, the highest tensile-shear strength was observed at laser the low frequency. The suitable welding condition can be obtain at the large pulse width and the low frequency.

The early detection of the bearing defects in rotating machinery is very important since the critical failure of bearing causes a machinery shutdown. However it is not easy to detect the vibration signal caused by the initial defects of bearing because of the high level of random noise. A signal processing technique, called the adaptive line enhancer(ALE) as one of adaptive filter, is used in this study. This technique is to eliminate random noise with little a prior knowledge of the noise and signal characteristics. Also we propose the optimal methods fir selecting the three main ALE parameters such as correlation length filter order and adaptation constant. Vibration signals f3r three abnormal bearings, including inner and outer raceways and ball defects, were acquired by Anderon(angular derivative of radius on) meter. The experimental results showed that ALE is very useful f3r detecting the bearing defective signals masked by random noise.

This article has been investigated the use of FFT for adhesive joints analysis between metal sheets. The method is based on the measurement of the reflection wave at the metal/adhesive interface. After describing briefly the physical aspects of the phenomenon, an index is defined to detect defective zone of the joint(both for the lack of adhesive and for insufficient adhesion): the influence of the experimental variables(variable stress...) on the measurement is discussed. By means of a control experiment it is shown that stress variation in adhesive joints are separate to be distinguished. In this paper, Nondestructive evaluation in adhesive joints are evaluated together with ultrasonic testing and finite element analysis.