• Journal of the Korean Wood Science and Technology
• /
• v.25 no.1
• /
• pp.23-27
• /
• 1997

Alkali-soluble extracts were prepared from barks of Japanese larch(Larix leptolepis). Siberian larch(Larix gmelineii) and Radiata pine(Pinus radiata) The effect of various factors, such as particle size, liquor ratio, extraction temperature, and reaction time, on the extracts yield was investigated. Particle sizes affected the alkali-soluble extracts; the finer the particle size, the higher extracts and extract efficiency. High temperature and high liquor ratio were more effective. In the range of 0.25% to 1% NaOH concentration, alkali extracts were increased with the increasing alkali concentration. However, extract yields were leveled off above 0.5% alkali concentration. Extractions with NaHCO3 were almost equivalent to those of NaOH extraction. 1% NaOH and 1% NaHCO3 resulted in the highest yields of alkaline extracts. Extracts from Japanese larch were lower than those from Siberian larch and Radiata pine barks. Siberian larch bark was the best raw material for tannin adhesives, because its extractive yield was higher than those of the other barks. Concerning pH of alkaline media during extraction, small increases of the extract yields were resulted at range of pH 7 to pH 9, while a large increases from pH 9.0 to pH 12. This phenomenon is attributed to higher alkalinity.

• Journal of the Korean Wood Science and Technology
• /
• v.26 no.4
• /
• pp.86-91
• /
• 1998

The drainage was used to determine the specific filtration resistance for wood and non-wood fibers. The drainage rate is also affected by factors that can be changed on consistency, pressure drop across the mat, basis weight, additives, and viscosity. Recent development of theoretical studies in flow through porous media and filtration operation emphasize the urgent need for more accurate data for porosity and specific filtration resistance. This study was investigated to determine specific filtration resistance of Hw, Sw-BKP and Kenaf fiber by filtration experimental. Freeness levels selected were 150,250,and $350m\ell$ CSF. The average specific filtration resistance decreased as freeness increased and resistance of Sw-BKP was greater than that of Hw-BKP. The filtrate and porosity increased and specific filtration resistance decreased as particle size of fiber increased.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.2
• /
• pp.181-195
• /
• 2020

Characteristics of carbonized biomass obtained from a Wood charcoal briquette manufacturing process using an open hearth kiln are analyzed in this research, and differences in the characteristics based on the results of a mechanical screening process and the position within the kiln. One type of biomass and five types of carbonized biomass were collected from a Wood charcoal briquette manufacturer. After screening and grinding processes were performed on samples of 1 type of biomass and 5 types of carbonized biomass extracted from a Wood charcoal briquettes manufacturer to classify by particle size, fixed carbon, ash, volatile matters, elemental composition, and high heating value (HHV) were measured. Experimental results showed that the carbonized biomass collected from the middle layer had the highest HHV, 20.4 MJ/kg, and therefore had the highest fuel quality. In terms of particle size, the carbonized biomass below 100 mesh had the lowest ash content and the highest HHV, carbon content, and fixed carbon content. Correlation analyses showed that ash content had negative correlations with HHV, volatile matters, fixed carbon, and carbon content, which suggested that ash content affected negatively on fuel quality.

• Journal of the Korean Wood Science and Technology
• /
• v.51 no.5
• /
• pp.334-344
• /
• 2023

Dregs from the sugar palm (Arenga pinnata) starch industry are considered a waste product of the agricultural industry and have not yet been optimally utilized. Therefore, this study aimed to manufacture particleboards from dregs using different amounts of adhesive and particle size ratios. Sugar palm dregs, which had been separated into fibers and powder/fine particles, were used as raw material for making particleboards. The fiber had an average length of 6.84 ± 3.23 cm, while the fine particles were of a size that passed through size 10 mesh and remained in size 60 mesh. Three ratios of fiber to fine particles (100:0, 75:25, and 50:50 wt%) with three different amounts of sucrose-citric acid adhesive (10, 15, and 20 wt%) were used in this study. Increasing the amount of fine particles and the resin content can improve the physical properties and the internal bond strength of boards made from sugar palm dregs. The fine particles possibly filled the gap between the fibers in the particleboard, while the fibers exhibited a high bending strength. As a result, a high-performance particleboard can be attained by combining the composition ratio of fiber/fine particles and resin content. In this study, particleboards made from fiber/fine particles (75:25 wt%) and adhesive content of 15 wt% and 20 wt% had the mechanical properties that met the requirements of Japanese Industrial Standard (JIS) A 5908 type 18. Sugar palm dregs have the potential to be used as raw materials to create value-added particleboards.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.6
• /
• pp.703-719
• /
• 2017

Miscanthus had a higher lignin content (19.5 wt%) and carbohydrate (67.6 wt%) than other herbaceous crops, resulting in higher pellet strength and positive effect on combustion. However, miscanthus also contains a high amount of hydrophobic waxes on its outer surface, cuticula, which limits the pellet quality. The glass transition of lignin and cuticula were related to forming inter-particle bonding, which determined mechanical properties of pellet. To determine the effects of surface waxes, both on the pelletizing process and the pellet strength were compared with raw and extracted samples through solvent extraction. In addition, to clarify the relationship between pellet process parameters and bonding mechanisms, the particle size and temperature are varied while maintaining the moisture content of the materials and the die pressure at constant values. Furthermore, kraft lignin was employed to determine the effect of kraft lignin as an additive in the pellets. As results, the removal of cuticula through ethanol extractions improved the mechanical properties of the pellet by the formation of strong inter-particle interactions. Interestingly, the presence of lignin in miscanthus improves its mechanical properties and decreases friction against the inner die at temperatures above the glass transition temperature ($T_g$) of lignin. Consequently, it could found that the use of kraft lignin as an additive in pellet reduced friction in the inner die upon reaching its glass transition temperature.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.3
• /
• pp.381-389
• /
• 2015

In this study, the effects of moisture content and particles size of ground particles of torrefied larch chips on the pelletizing process were investigated depending on torrefaction conditions ($220^{\circ}C$-50 min, $250^{\circ}C$-50 min, $250^{\circ}C$-120 min). The moisture content in the torrefied chip decreased to 0.69~1.75%, while ash content and calorific value increased compared to untreated chip. In addition, weight loss significantly increased during torrefaction due to hemicellulose degradation. The carbon content in torrefied larch chip increased compare to untreated larch chip, while the hydrogen and oxygen contents decreased. The lignin and glucan contents in torrefied larch chip increased with increasing severity of the torrefaction condition, while hemicellulose decreased. In the particle size distribution of ground particles of torrefied larch chip, larch torrefied at severe conditions was found to produce smaller particles (~1 mm) than that of the larch torrefied at mild conditions. Macropore (over $500{\AA}$) in the torrefied particle was produced during torrefaction. During the pelletizing using ground particles of torrefied larch chip, the pressure needed in pelletizing decreased and pellet length increased with increasing moisture content, regardless of the particle size.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.4
• /
• pp.309-314
• /
• 2018

Size reduction is an important pre-processing operation for utilizing biomass as a sustainable resource in industrial-scale energy production and as a raw material for other industries. This work investigates the size reduction characteristics of air-dried Miscanthus sacchariflorus Goedae-Uksae 1 (Amur silver grass) via image processing and identifies the morphological characteristics of comminuted and screened M. sacchariflorus. At chopping lengths of 18, 40, 80, and 160 mm, 81%, 77%, 78%, and 76% of the particles, respectively, passed through a 4-mm sieve. Even a knife mill with a very small screen aperture (>1 mm) admitted over 10% of the particles. The average circularity and aspect ratio of the particles were <0.30 and >10, respectively. These results confirm that in all preparation modes, most M. sacchariflorus particles were needle-like in shape, irrespective of the type of preparation.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.4
• /
• pp.74-81
• /
• 2008

The writing brush, ink stick, paper, and ink stone were the four precious things of the studying and recording in oriental world until even nowaday. The oriental paper was comparatively well evaluated in many papers and reviews, but it is difficult to find some scientific reports or reviews about the ink stick. In this paper, the scientific aspect of ink sticks of oriental maine three country(Korea, China, Japan) were evaluated by the physical, chemical and microscopic analysis. The result could summarized as fellows; 1. The Korean lampblack ink stick contains more carbon and less nitrogen and the Chinese ink sticks contain less carbon and more oxygen. 2. The Korean lampblack and cowhide glue contain relatively higher amount of sulphur. 3. The particle size distribution of carbon in the ink stick was not change after grinding in the ink stone. 4. The particle size of carbon and the pore size in the charcoal ink sticks of three country were larger than those of the lampblack ink sticks. 5. The ink solution of the charcoal ink sticks shows high roundness on Hanji while the ink solution of the lampblack ink sticks is spread readily to Hanji surface. 6. The change of whiteness in printing of the ink sticks is notable in thermal treatment.

• Korean Chemical Engineering Research
• /
• v.50 no.5
• /
• pp.850-859
• /
• 2012

Devolatilization is an important mechanism in the gasification and pyrolysis of woody biomass, and has to be accordingly considered in designing a gasifier. In order to describe the devolatilization process of wood particle, there have been proposed a number of empirical correlations based on experimental data. However, the correlations are limited to apply for various reaction conditions due to the complex nature of wood devolatilization. In this study, a simple model was developed for predicting the devolatilization of a wood particle in a fluidized bed reactor. The model considered the drying, shrinkage and heat generation of intra-particle for a spherical biomass. The influence of various parameters such as size, initial moisture content, heat transfer coefficient, kinetic model and temperature, was investigated. The devolatilization time linearly increased with increasing initial moisture content and size of a wood particle, whereas decreases with reaction temperature. There is no significant change of results when the external heat transfer coefficient is over 300 $W/m^2K$, and smaller particles are more sensitive to the outer heat transfer coefficient. Predicted results from the model show a similar tendency with the experimental data from literatures within a deviation of 10%.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06a
• /
• pp.61-66
• /
• 2006

Over the past 20 years there has been a revolution involving the use of nano or macro size particles as drainage and retention systems during the manufacture of paper. More recently a group of patented technologies called Synthetic Mineral Microparticles (SMM) has been invented and developed. This system has potential to further promote the drainage of water and retention of fine particles during papermaking. Prior research, as well as our on preliminary research showed that the SMM system has advantages in both of drainage and retention compared with montmorillonite (bentonite), which one of the most popular materials presently used in this kind of application. In spite of the demonstrated advantages of this SMM system, the properties and activity of SMM particles in the aqueous state have not been elucidated yet. Streaming current titrations with highly charged polyelectrolytes were used to measure the charge properties of SMM and to understand the interactions among SMM particles, fibers, fiber fines, and cationic polyacrylamide (cPAM) as a retention aid. It was found that pH profoundly affects the charge properties of SMM, due to the influence of Al-ions and the Si-containing particle surface. SEM pictures, characterizing the morphology, geometry and size distribution of SMM, showed an broad distribution of primary particle size. Dilution of SMM mixturee appeared to wash out particles smaller than 100 nm from the surface of larger particles, which themselves appeared to be composed of fused primary particles. DSC thermoporometry was used to measure the size distribution of nanopores within SMM particles.