• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.6C
• /
• pp.259-265
• /
• 2012

This paper investigates engineering characteristics of lightweight soils mixed with air foam and tire powder. Lightweight soils could be used as foundation materials, back-fills of reducing vibrating or abutment, and so on. Unconfined and triaxial compression tests were carried out to analyze strength and deformation characteristics of lightweight soils by changing target moist unit weight and cement contents. In comparison with strength characteristics of two different kinds of lightweight soils with same most unit weights ($13kN/m^3$), unconfined compression tests showed similar compressive strength, however, triaxial compression tests showed that compressive strength of lightweight soils mixed with waste tire powder was relatively larger strength than that of lightweight soils mixed with air foam because of elasticity of waste tire powder. Also, unconfined and triaxial compressive strengths of most of lightweight soils increase with increases of moist unit weight and cement contents. However, the strength of lightweight soils mixed with air foam under $11kN/m^3$, when moist unit weight exceeds a certain cement contents, decreases even though cement contents increase because of the effect in a void gap of air foam.

• Resources Recycling
• /
• v.27 no.2
• /
• pp.24-31
• /
• 2018

In this study, waste ITO target is dissolved into hydrochloric acid to generate a complex indium-tin chloride solution. Nano sized ITO powder with an average particle size below 30 nm are generated from these raw material solutions by spray pyrolysis process. Also, in this study, thermodynamic equations for the formation of indium-tin oxide (ITO) are established. As the reaction temperature increased from $800^{\circ}C$ to $900^{\circ}C$, the proportion and size of the spherical droplet shape in which nano sized particles aggregated gradually decreased, and the surface structure gradually became densified. When the reaction temperature was $800^{\circ}C$, the average particle size of the generated powder was about 20 nm, and no significant sintering was observed. At a reaction temperature of $900^{\circ}C$, the split of the droplet was more severe than at $800^{\circ}C$, and the rate of maintenance of the initial atomized droplet shape decreased sharply. The average particle size of the powder formed was about 25 nm. The ITO particles were composed of single solid crystals, regardless of reaction temperature. XRD analysis showed that only the ITO phase was formed. Remarkably, the specific surface area decreased by about 30% as the reaction temperature increased from $800^{\circ}C$ to $900^{\circ}C$.

• Journal of the Korean Applied Science and Technology
• /
• v.28 no.2
• /
• pp.135-139
• /
• 2011

In order to make high-purity ferro-manganese from $Mn_3O_4$ waste dust, the application of aluminothermite process to the reduction of the waste dust was investigated. The mixture from $Mn_3O_4$ dust as metallic source and Al metal powder as the reductant ignited, and reduced with an extremely intense exothermic reaction. The rapid propagation of the aluminothermite reaction occurred spontaneously and stably by ignition of the mixture. The Manganese having some alloy elements emerged as liquids due to the high temperatures reached up to about $2,500^{\circ}C$ and separated from the liquid by their differences of specific gravity. The result of thermite reaction showed the fact that can be obtained high purity ferro-manganese which have over about 90% of manganese content and lower impurities such as C, P, S than those of KS D3712 specification. The recovery of manganese from $Mn_3O_4$ dust was lower level of about 65% than about 75% from manganese ore by electric furnace process, that is due to spatter loss because of its extremely intense thermite reaction. But it will be improved by the process designed to provide CaO as the cooler or to use the Al metal powder having larger particle size distribution.

• Journal of Powder Materials
• /
• v.28 no.6
• /
• pp.497-501
• /
• 2021

Cobalt (Co) is mainly used to prepare cathode materials for lithium-ion batteries (LIBs) and binder metals for WC-Co hard metals. Developing an effective method for recovering Co from WC-Co waste sludge is of immense significance. In this study, Co is extracted from waste cemented carbide soft scrap via mechanochemical milling. The leaching ratio of Co reaches approximately 93%, and the leached solution, from which impurities except nickel are removed by pH titration, exhibits a purity of approximately 97%. The titrated aqueous Co salts are precipitated using oxalic acid and hydroxide precipitation, and the effects of the precipitating agent (oxalic acid and hydroxide) on the cobalt microstructure are investigated. It is confirmed that the type of Co compound and the crystal growth direction change according to the precipitation method, both of which affect the microstructure of the cobalt powders. This novel mechanochemical process is of significant importance for the recovery of Co from waste WC-Co hard metal. The recycled Co can be applied as a cemented carbide binder or a cathode material for lithium secondary batteries.

• Resources Recycling
• /
• v.14 no.3
• /
• pp.55-62
• /
• 2005

Mechanical properties of shell powder containing mixed recycled plastics were investigated depending on the shell content and surface modification. First, shell powder and LDPE were compounded using the twin screw extruder to manufacture 40 wt% master batch(M/B), and the M/B was blended with LDPE to produce bulk specimens with 10, 20, 30 and 40 wt% shell content. To improve the compatibility of shell powder with mixed recycled plastics matrix, surface of shell powder was chemically modified with cations or cationic surfactant. Surface modified shell was also used to prepare bulk specimens with the same shell content. Mechanical property analysis showed obvious improvement for the surface modified shell containing bulk specimens compared to unmodified ones. These results can lead to the development of new applications for the mixed recycled plastics.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.6
• /
• pp.286-290
• /
• 2012

Boehmite (AlOOH) powder was synthesized using waste aluminium etching solution. In waste solution, precipitated phase was gibbsite ($Al(OH)_3$), and boehmite (AlOOH) phase was obtained at pH of 7 and 8 controlled by addition of acid. Boehmite powder was obtained by washing process to remove the Na ion in precipitated solution. Mean particle size of obtained powder was 40 nm. Boehmite phase transformed to ${\alpha}-Al_2O_3$ phase via ${\gamma}-Al_2O_3$, ${\delta}-Al_2O_3$, and ${\Theta}-Al_2O_3$.

• The Korean Journal of Food And Nutrition
• /
• v.30 no.3
• /
• pp.578-590
• /
• 2017

An agricultural waste, pomegranate (Punica granatum L.) peel is known to be rich in total phenolics, which are flavonoids having strong antioxidant effects. In this study, pomegranate peel sponge cakes were prepared with varying ratios of freeze dried pomegranate peel powder (0, 1, 3, 5, 7% (w/w)) to examine their effect on quality characteristics, retrogradation and antioxidant activities. The specific gravity and moisture contents of 3, 5, and 7% pomegranate peel powder showed higher values than the control and 1% group. Addition of pomegranate peel powder increased the batter yield, while there was a significant decrease in baking loss. Increasing pomegranate peel powder content significantly decreased the lightness (L) (from 75.03 to 57.04) and pH values, whereas redness (a), yellowness (b) and ${\Delta}E$ were increased. Increasing concentration of the peel powder also increased the hardness and chewiness, while the springiness and cohesiveness decreased. Considering the Avrami equation, Avrami exponene (n) decreased from 1.8055 (control) to 0.9199 (7% pomegranate peel powder). Time constant (1/k) was lowest in control (at 17.64) and highest in the 7% group (39.84). Total polyphenol, flavonoid content, DPPH and ABTS radical scavenging activities significantly increased with increments in the content of pomegranate peel powder. A sensory evaluation by the 7-point scaling method showed that the sponge cake containing 7% pomegranate peel powder had the highest scores in color, flavor, sweetness, chewiness and overall acceptability. Hence, it is considered that sponge cake supplemented with 7% pomegranate peel powder is the most appropriate for quality characteristics, retrogradation and antioxidant activities.

• The Korean Journal of Community Living Science
• /
• v.18 no.1
• /
• pp.39-53
• /
• 2007

The purpose of this study was to determine the characteristics of an experimental protective clothing material with regard to comfort and isolation from the hazardous heavy metals produced in municipal waste incineration. An analysis was conducted on the total concentrations of heavy metals in some parts such as surface, middle layer, and interior for the treated fabric, and the untreated one, and working clothes. We conclude that the processed fabric with charcoal for working clothes showed the least exposure to heavy metals of the three. Working clothes worn by workers during waste incineration were much more contaminated than the untreated and treated materials. The material of working clothes could be chosen according to the function with regard to its original chemical characteristics, which are the proper results of the dyeing process. The processed fabric material has high degrees of moisture regain, thermal insulation, water vapor penetration, and antibacterial function; consequently, it is much more comfortable to wear. The fabric material proposed in this research contributed much more to blocking heavy metal concentrations (such as Cd, Pb, Cu, Cr, Zn, Mn) than did the fabric of working clothes at present. Consequently, we strongly suggest that the material of working clothes be upgraded by adopting the above-mentioned charcoal-processed fabric. Materials of working clothes must be improved to increase comfort and prevent harmful gas, flying dust, and heavy metals from permeating the fabrics.

• Computers and Concrete
• /
• v.29 no.5
• /
• pp.335-346
• /
• 2022

Geopolymers are an important alternative material supporting recycling, sustainability, and waste management. Durability properties are among the most critical parameters to be investigated; in this study, the durability of manufactured geopolymer samples under the attack of 10% magnesium sulfate and 10% sodium sulfate solution was investigated. 180 cycles of freezing and thawing were also tested. The experimentally obtained results investigate the durability of geopolymer mortar prepared with fly ash (class F) and alkali activator. Three different quarry dust wastes replaced the river sand aggregate: limestone, marble, and basalt powder as fine filler aggregate in three different replacement ratios of 25%, 50%, and 75% to produce ten series of geopolymer composites. The geopolymer samples' visual appearance, weight changes, UPV, and strength properties were studied for up to 12 months at different time intervals of exposure to sulfate solutions to investigate sulfate resistance. In addition, Scanning Electron Microscopy (SEM), EDS, and XRD were used to study the microstructure of the samples. It was beneficial to include quarry waste as a filler aggregate in durability and mechanical properties. The compact matrix was demonstrated by microstructural analysis of the manufactured specimens. The geopolymer mortars immersed in sodium sulfate showed less strength reduction and deterioration than magnesium sulfate, indicating that magnesium sulfate is more aggressive than sodium sulfate. Therefore, it is concluded that using waste dust interrogation with partial replacement of river sand with fly ash-based geopolymers has satisfactory results in terms of durability properties of freeze-thaw and sulfate resistance.

• Journal of the Korean Ceramic Society
• /
• v.55 no.1
• /
• pp.90-93
• /
• 2018

In this study, n-type $Bi_2Te_3$ in thermoelectric scrap is recovered through a wet reduction process. The recovered powder (tellurium) is grafted onto gas sensor in a new application that is not a thermoelectric device. Bismuth-rich powder is prepared by adding hydrazine when pH of the solution is brought to 13 using NaOH. The pH of the filtered solution was reduced using $HNO_3$, and then hydrazine was added to perform the re-reduction reaction. The tellurium-rich powder can be obtained through this reaction. The elemental analysis for these powders is confirmed by energy dispersive X-ray spectroscopy (EDS) analysis ; the successful separation of bismuth and tellurium is confirmed. Separated tellurium powder is mixed with DMF solvent and ethyl cellulose binder to confirm gas sensing properties. The tellurium paste was exposed in $NO_x$ atmosphere and exhibited a rapid reaction rate and recovery rate of less than 3 minutes for the gas.