• Proceedings of the KIEE Conference
• /
• 2003.11a
• /
• pp.174-177
• /
• 2003

Kinds of most frequent faults happened on overhead distribution system are the single line-to-ground fault, the line-to-line fault and the two line-to-ground fault. Occasionally, the three line-to-ground fault and the disconnection of a wire are happened in severe conditions. In this study, the single line-to-ground fault, the line-to-line fault, two line-to-ground fault on three-phase four-wire overhead distribution system were experimentally simulated and characteristics of total leakage current of distribution arrester caused by these faults were investigated. Also, the changing aspect of total leakage current of distribution arrester caused by voltage variation was investigated. In a consequence, abnormal voltages caused by voltage variation, the line-to-line fault, the two line-to-ground fault have a little effect on total leakage current of ZnO arrester. But abnormal voltages caused by the single line-to-ground fault have an important effect on total leakage current of ZnO arrester.

• Korean Journal of Crystallography
• /
• v.16 no.2
• /
• pp.141-148
• /
• 2005

It is well known that the general metals have a lot of grain boundaries. The grain boundaries play a negative role to increase the resistivity and to decrease the conductivity. The small resistivity and the large conductivity have been a goal of the material scientists, and no signal noise, perfect signal transfer, and the realization of the real sound are the dream of electronic engineers and audio manias. Generally, oxygen free copper (OFC) and Ohno continuous casting (OCC) copper cables have been used for the purpose of the precise signal transfer and low noise. However they still include a lot of grain boundaries. In our study, we have grown the single crystal by the Czochralski method and succeeded to produce single crystal wires from the crystal in the dimension of $0.5{\times}0.5{\times}2500mm$. The produced wire still possesses very good single crystal properties. We observed the structure of the wire, and measured the resistance and impedance. Glow Discharge Spectrometer (GDS) was used for analyzing the compositions of copper single crystals and commercial copper. Current-Voltage curve, resistance, total harmonic distortion and speaker frequency response were measured for comparing electrical and acoustic properties of two samples.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.2
• /
• pp.50-56
• /
• 2007

Wire forming machine is widely used in industries to make a variety of wire products such as coil springs and links. Along with the rapid development of CNC technologies, the usage of wire forming machine varies from single-purpose machinery to universal CNC machinery. Rotating the wires while feeding them simultaneously, we can improve the performance of the machines with aspects of efficient tooling and complicated geometric forming. In this study, a new gear train is developed for the control of both feeding and rotating wires independently at the same time. The developed mechanism has many benefits as following, making more complicated geometric and precision products, easier tooling, and simpler programming.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.11a
• /
• pp.297-299
• /
• 2004

In multi-ground distribution system, overhead ground wire and neutral wire are parallel connected to offer the electrical power energy and protect damage of lightning strokes. Therefore a case where the two wires become single wire, the power company can get the benefit such as installation cost saving and line fault protection by simplify of distribution line. In this paper we describe the result of impulse test in both system ; one is the present power system the other is unified power system parallel connected overhead ground wire and neutral wire. As a result of this impulse test, the present power system get lower impulse voltage than the unified power system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.609-612
• /
• 2001

To investigate the magnetic field distribution of power line, we used amorphous wire sensor. And we discuss extremely low frequency magnetic field distribution dependent upon arrangement of power line and shielding pipe made from iron or alumimum materials by both measurement and FEM(Finite Element Method) analysis. Appling current of single phase 60 [Hz] 15 [A] is supplied to copper wire coated enamel resign. As the results, we confirmed that linear characteristics of amorphous wire sensor is very excellent and measurement value agrees with FEM calculation. Magnetic field distribution due to shielding materials is changed by permeability and conductivity.

• Proceedings of the KIEE Conference
• /
• 2005.11b
• /
• pp.80-82
• /
• 2005

There is a method for stringing conductors which is connected to a wire over transmission towers by helicopter or human power and the wire and conductors are pulled by an engine puller. The length of one string section is usually 4-6 km and 2-4 conductors are strung at the same time with a single wire. A tensioner is used to maintain the sag and a running board is installed between the wire and conductors to prevent the rotation of conductors but the variance in topology, the line angle and unequal wiring tension between conductors causes conductor rotation damage or the conductor connection point to breakaway when the pulley is passed. This paper presents a method to prevent conductor rotation during stringing by inserting a pulley in the running board and equally maintaining conductor tension by sling wire after developing and testing.

• Journal of the Semiconductor & Display Technology
• /
• v.6 no.1 s.18
• /
• pp.17-22
• /
• 2007

Recent new packages such as MCP(Multi-Chip Package), QDP(Quadratic Die Package) and DDP(Dual Die Package) have stack type configuration. This kind of multi-layer package is thicker than single layer package. So there is need for the low height looping technology in wirebonder to make these packages thinner. There is stiff zone above ball in wirebonder wire which is called HAZ(Heat Affect Zone). When making low height loop (below $80\;{\mu}m$) with traditional forward loop, stiff wire in HAZ(Heat Affected Zone) above ball is bended and weakened. So the traditional forward looping method cannot be applied to low height loop. SSB(stand-off stitch) wire bonding method was applied to many packages which require very low loops. The drawback of SSB method is making frequent errors at making ball, neck damage above ball on lead and the weakness of ball bonding on lead. The alternative looping method is BNL(ball neckless) looping technology which is already applied to some package(DDP, QDP). The advantage of this method is faster in bonding process and making little errors in wire bonding compared with SSB method. This paper presents the result of BNL looping technology applied in assembly house and several issues related to low loop height consistence and BNL zone weakness.

• Proceedings of the KIPE Conference
• /
• 2019.11a
• /
• pp.106-107
• /
• 2019

This paper propose a new 3D SVM method for three-phase four wire inverter for fault isolation at a single line ground fault. The available switching combination for isolation of a single line ground fault was analyzed. Using this method, voltage vector diagrams according to each switching combination were classified according to various ground fault situations, and 3D SVM method was performed by generating command for fault isolation. The proposed methods are mathematically analyzed and verified by PSIM simulation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.5
• /
• pp.301-306
• /
• 2017

Wire electrical discharge machining (WEDM) process was evaluated to slice Silicon (Si) for various applications. Specifically, various Si workpieces with various resistances, such as single and multi crystalline Si bricks and wafers were used. As conventional slicing processes, such as slurry-on or diamond-on wire slicing, are based on mechanical abrasions between Si and abrasive, there is a limitation to decrease the wafer thickness as well as kerf-loss. Especially, when the wafer thickness is less than $150{\mu}m$, wafer breakage increases dramatically during the slicing process. Single crystalline P-type Si bricks and wafers were successively sliced with considerable slicing speed regardless of its growth direction. Also, typical defects, such as microcracks, craters, microholes, and debris, were introduced when Si was sliced by electrical discharge. Also, it was found that defect type is also dependent on resistance of Si. Consequently, this study confirmed the feasibility of slicing single crystalline Si by WEDM.

• Journal of Trauma and Injury
• /
• v.28 no.2
• /
• pp.55-59
• /
• 2015

Purpose: To compare clinical and radiographic outcomes of between two and three Kirschner wire(K-wire) intramedullary fixation for fractures in the neck of the metacarpal bone. Methods: A single institutional retrospective review identified 28 cases of metacarpal fractures between March 2010 and August 2014. Each of the cases met the inclusion criteria for closed, extra-articular fractures of the neck of the metacarpal bone. The patient groups were divided by the number of K-wire. Outcomes were compared for range of motion of the metacarpophalangeal joint, radiographic parameters, and period until union. Results: The fractures were treated with either 2 Kirschner wire fixation (n=10) or 3 Kirschner wire fixation (n=18). The active range of motion of metacarpophalangeal joint and radiographic result showed no statistically significant difference between the two groups. The mean union period was 5.9 weeks. However, four cases suffered distal head perforation in 2 K-wire fixation group and one case in 3 K-wire fixation group. Conclusion: Multiple retrograde intramedullary Kirschner wire fixation is a good treatment of choice for fractures in the neck of the metacarpal bone. To prevent metacarpal head perforation, it is preferred to use three K-wires than two K-wires.