• 대한금속재료학회지
• /
• 제49권10호
• /
• pp.797-804
• /
• 2011

In this study, the mechanisms of the three steps (the polymer deposition step, the polymer etching step and the Si etching step) that constitute the Bosch process were investigated. The effects of radicals and ions on each step were quantitatively analyzed by comparing the simulated aspect ratio dependency of the deposition or etch rate with the experimental results. In the polymer deposition step, fluorocarbon polymer is deposited by chemical reactions of $CF_x$ radicals, of which the reaction probability is 0.13. Although the polymer etching step and the Si etching step were conducted under the same conditions, the etching mechanisms of polymer and Si were found to be quite different. In the polymer etching step, both chemical etching and physical sputter-etching contribute to the polymer etching. Whereas, in the Si etching step, Si is chemically etched by F radicals, of which the reactivity is greatly increased by the bombardment of energetic ions.

• 한국전기전자재료학회논문지
• /
• 제11권2호
• /
• pp.101-105
• /
• 1998

This paper describes anisotropic etching technology of highly doped polysilicon. The main etching gases are $Cl_2$ and $SiCl_4$ for reactive ion etching of polysilicon. The mixed $CHCl_3$ to main etching gas makes polymer on etching side wall, so it prevents side etching of polysilicon. The etch rate of polysilicon is increased with increasing RF power. But the etching rate is decreased as the flow rate of $CHCl_3$ is increased with fixed RF power. The etch selectivity of polysilicon and $SiO_2$ is about 12:1. And that of polysilicon and $Si_3N_4$ is about 19:1. In the main etching gas condition, the slope of polysilicon is same as that of photoresist. But in the mixed $CHCl_3$ condition, the slope of polysilicon is larger than that of photoresist. This represents that the polymer made on side wall by added $CHCl_3$ prevents side etching, so anisotropic etching can be possible by polymer.

• 한국정밀공학회지
• /
• 제22권9호
• /
• pp.60-68
• /
• 2005

To investigate the effects of beam focusing in the etching of polymers with short pulse Excimer lasers, a polymer etching model of SSB's is combined with a beam focusing model. Through the numerical simulation, it was found that in the high laser fluence region, SSB model considering both photochemical and thermal contribution is considered to be suitable to predict the etched hole shape than a simple photochemical etching model. The average temperature distribution into the substance obtained by assuming 1-D heat transfer is found to be fairly similar to the fluence distribution on the ablated surface. The experimental etching data fur polymers are used to give material properties for ablation model. The fitted etch depth curve gives a nice agreement with the experimental data.

• 반도체디스플레이기술학회지
• /
• 제2권3호
• /
• pp.7-11
• /
• 2003

In this research, the etching characteristics of via contact and deep contact hole have been studied using multi-pole inductively coupled plasma(MICP) etching system. We investigated Plasma density of MICP source using the Langmuir probe and etching characteristics with RF frequency, wall temperature, chamber gap, and gas chemistry containing Carbon and Fluorine. As the etching time increases, formation of the polymer increases. To improve the polymer formation, we controlled the temperature of the reacting chamber, and we found that temperature of the chamber was very effective to decrease the polymer thickness. The deep contact etch profile and high selectivity(oxide to photoresist) have been achieved with the optimum mixed gas ratio containing C and F and the temperature control of the etching chamber.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.143-146
• /
• 2002

Unsized AS-4 carbon fibers were etched by RF plasma and then coated via plasma polymerization in order to enhance adhesion to vinyl ester resin. The gases utilized for the plasma etching were Ar, $N_2 and O_2$, while the monomers used for the plasma polymerization coating were acetylene, butadiene and acrylonitrile. The conditions for the plasma etching and the plasma polymerization were optimized by measuring interfacial adhesion with vinyl ester resin via micro-droplet tests. Among the treatment conditions, the combination of Ar plasma etching and acetylene plasma polymerization provided greatly improved interfacial shear strength (IFSS) of 69MPa compared to 43MPa with as-received carbon fiber. Based on the SEM analysis of failure surface and load-displacement curve, it was assume that the failure might be occurred at the carbon fiber and plasma polymer coating. The plasma etched and plasma polymer coated carbon fibers were subjected to analysis with SEM, XPS, FT-IR or Alpha-Step, and dynamic contact angles and tensile strengths were also evaluated. Plasma polymer coatings did not change tensile strength and surface roughness of fibers, but decreased water contact angle except butadiene plasma polymer coating, possibly owing to the functional groups introduced, as evidenced by FT-IR and XPS.

• 한국안광학회지
• /
• 제17권2호
• /
• pp.119-126
• /
• 2012

목적: 안경 렌즈 코팅 막을 불화수소산을 이용하여 상온에서 단시간 화학적으로 식각한 뒤 코팅 막과 렌즈 원재료의 변화를 살펴보고자 하였다. 방법: GRAY 70%로 염색된 vinyl ester계 고분자(Lens A)와 thiourethane계 고분자렌즈(Lens B)를 불화수소산을 이용해 5분, 10분 또는 15분 동안 식각한 뒤 재료의 기계적 물성과 하드코팅과 반사방지코팅 등 코팅 막의 손상 정도, 그리고 굴절률 광투과율 등 렌즈의 특성 변화를 관찰하였다. 결과: 두 재료 모두 식각 전과 후의 굴절력에는 큰 변화가 없었지만 반사방지코팅과 하드코팅이 차례로 제거되었고 렌즈 표면에도 손상을 주어 UV 투과율이 증가되었으며 기계적 물성은 소하였다. 화학적 식각으로 인한 렌즈의 물성 변화는 thiourethane계 고분자 렌즈에서 더 크게 나타났다. 결론: 고분자 재료의 특성에 따라 불화수소산에 대한 반응성이 다르기 때문에 식각에 따른 렌즈 자체의 물성 변화가 다르게 나타남을 알 수 있었다.

• Transactions on Electrical and Electronic Materials
• /
• 제9권4호
• /
• pp.156-162
• /
• 2008

We report results on a study of inductively coupled plasma (ICP) etching of Parylene-C (poly-monochloro-para-xylylene) films using an $O_2$ gas. Effects of process parameters on etch rates were investigated and are discussed in this article from the standpoint of plasma parameter measurements, performed using a Langmuir probe and modeling calculation. Process parameters of interest include ICP source power and pressure. It was shown that major etching agent of polymer films was oxygen atoms O($^3P$). At the same time it was proposed that positive ions were not effective etchant, but ions played an important role as effective channel of energy transfer from plasma towards the polymer.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2007년도 춘계학술발표대회 및 제12회 신소재 심포지엄
• /
• pp.32.2-32.2
• /
• 2007

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1582-1584
• /
• 2008

This paper reports a simple fabrication method for creating the superhydrophobic polymer surface using a plasma etching. Generally, it is necessary for the superhydrophobic surfaces to have a rough structure on surface with the composition of the low surface energy. In this study, Poly(methyl methacrylate) (PMMA), poly(ethylene terephthalate) (PET), acrylonitrile butadiene styrene (ABS) with superhydrophobic surface were fabricated using $O_2$ plasma etching and vapor deposition with the fluoroalkylsilane self-assembled monolayers. The plasma treated polymer surfaces are covered with the nano-pillar shaped structures after treatment for $1{\sim}2min$. And these samples with FOTS SAMs coating are showed the superhydrophobicity having the water contact angle of around $150^{\circ}$ and sometimes around $180^{\circ}$ depending on the treatment time. Furthermore the nanostructured polymer is transparent for the visible light.

• Korean Chemical Engineering Research
• /
• 제44권5호
• /
• pp.520-527
• /
• 2006

본 연구에서는 FC(fluorocarbon) 플라즈마 반응기에서 입사하는 이온에너지에 따른 고분자 증착, 식각과 증착의 경쟁반응 및 물리적 스퍼터링 등의 여러 표면 현상들을 모델링하였다. $SiO_2$ 식각에 대한 표면반응은 식각반응 영역을 잘 혼합된 CSTR(continuous stirred tank reactor) 가정을 도입하여 이온 도움에 의한 식각으로 모사되었다. 정상상태 고분자층을 통한 식각과 증착의 경쟁반응의 모델링은 이온 도움에 의한 고분자 생성 및 분해 메커니즘을 제안하여 수행하였다. 이러한 메커니즘은 최근 발표된 실험 및 분자동력학적 전산모사 결과에 기초하였으며,모델 계수들은 빔실험 결과 및 플라즈마 실험결과들을 이용하여 구하였다. 최종 개발된 모델의 결과들은 타당성을 검증하기 위해 문헌에 보고된 실험결과들과 비교하였다.