• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.10
• /
• pp.1150-1157
• /
• 1988

In this paper, the reconstruction of complex permittivity distribution on a rectangular cross section of inhomogeneous dielectric cylinders is performed by employing the spectral inverse scattering scheme presented in the part I of these companion papers. Numerical simulations provide the superresolution to the permitivity profiles nearly regardless of the measurement locations of the scattered field and the permittivity distributions on the cross section.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.926-929
• /
• 1999

In this paper, we have studied the role of sources gases, SiH$_4$, NH$_3$ and $N_2$, to produce Si-N and Si-H bond in PECVD. The correlations of a deposition rate, a refractive index and a permitivity were investigated with the NH$_3$ flow rate of 6, 9 and 12 sccm, and SiH$_4$ flow rate of 20, 30 and 40 sccm, and substrate temperature of 150, 250 and 35$0^{\circ}C$. But the $N_2$ flow rate and chamber pressure were fixed at 55 sccm and 700mTorr. And then MIM capacitors were fabricated and tested for MMIC applications.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.9
• /
• pp.1250-1256
• /
• 1995

In this paper, shielded suspended coplanar waveguide with multiple anisotropic substrates is analyzed by the point matching method in the quasi-TEM mode appoximation. The characteristic impedance and the effective dielectric constant are calculated by varying the width of center strip and gap between the center strip and the ground strip. And also the characteristic parameters are calculated as a function of ${\varepsilon}_{x}/{\varepsilon}_{y}$) and a permitivity of the support substrate. Approaching the ground strip to infinity, the values of the characteristic parameters are found to be in good agreement with the other results by variational method.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.11C no.2
• /
• pp.18-22
• /
• 2001

The thin films of high permitivity in ferroelectric materials using a capacitor are applied to DRAMs and FRAMs. (Ba, Sr)TiO$_3$ thin as ferroelectric materials were prepared by the sol-gel method and made by spin-coating on the Pt/Sio$_2$/Si substrate at 4,000 [rpm] for 10 seconds. The structural characteristics of the surface were analyzed by fractal dimension. The thickness of BST ceramics thin films was about 260∼280 [nm]. The property of the leakage current was stable with 10-9∼10-11[A] when the applied voltage was 0∼3[V]. BST thin films ha low leakage current properties when fractal dimension was low and a coating area was high.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.6
• /
• pp.143-148
• /
• 1994

In order to study the effect of D.C resistivity of sample on electromagnetic loss of ferrite at microwave frequency, samples were prepared for having differences in resistivity of an order of two. Microwave permeability($\mu$), permitivity($\varepsilon$) and effective linewidth(${\Delta}H_{eff}$), and ferromagnetic resonance linewidth(${\Delta}$H) were characterized. Tan${\delta}{\mu}$, tan${\delta}{\varepsilon}$ and ${\Delta}H_{eff}$ were decreased with increasing the resistivity and (${\Delta}$H) was increased with increasing Fe concentration, which was due to an increase of anisotropy magnetic field (=Ha).

• Journal of Industrial Technology
• /
• v.31 no.A
• /
• pp.109-112
• /
• 2011

In this paper, we proposed a planar reversed triangle monopole antenna for UWB(Ultra Wideband) communication. RF-60A substrate of 0.64 mm thickness and 6.15 relative permitivity and 0.035 mm conductor of thickness and loss tangent 0.0025 is used for implementation. We have used Ansoft $HFSS^{TM}$(High Frequency Structure Simulator) to simulate the proposed antenna. The proposed antenna showed return losses about -10 dB, nearly omni-directional radiation patterns and maximum gains are over -5 dBi at the frequency band from 3.1 GHz to 10.6 GHz for ultra wide band communication.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.05a
• /
• pp.137-139
• /
• 1992

By addition of 1～5mol% CeO$_2$to powders with composition in the BaO-Nd$_2$O$_3$-TiO$_2$, temperature coefficient of permittivity of sintered ceramics may be decreased from approximately-140ppm/$^{\circ}C$～-65ppm/$^{\circ}C$. Dense, fine grained ceramics were prepared with permitivity within the range of 78～92 and Q above 1000.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.436-439
• /
• 2000

Change of dielectric loss of use in high relative permitivity capacitor BaTiO$_3$ ceramic depends on Mn doping have been investigated. The powders used in this study were commercial BaTiO$_3$, TiO$_2$and, MnCO$_3$. Sample was fabricated by conventional ceramic process. The quantity of Mn was changed gradually from 0.lmol% to 10mo1%. The sintering densities were reduced with increasing amount of MnCO$_3$. This result is because of increase of low density second phase BaMnO$_3$. When the samples were doped by over 0.2mol% of MnCO$_3$, average grain sizes were enlarge to several tens ${\mu}{\textrm}{m}$. The dielectric losses were reduced by Mn doping to lmol% but, increased from lmol% to 10mo1% gradually.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.179-179
• /
• 2009

This is for the electrical characterization by IDC pattern using BST$(Ba_{0.5}Sr_{0.5}TiO_3)$ thin film. BST materials had been chosen for high frequency applications due to it's high permitivity and tunability. The BST thin films have been deposited on $Al_2O_3$ Substrates by Nd-YAG pulsed laser deposition with a 355nm wavelength at $700\;^{\circ}C$. The post deposition annealing at $750^{\circ}C$ in flowing $O_2$ atmosphere for 1 hours. The capacitance of IDC patterns have been measured from 1 to 10 GHz as a function of electric field ($\pm40$ KV/cm) at room temperature using inter-digital Au electrodes deposited on top of BST. The IDC patterns have three type of fingers number. For the 10 pairs finger was the best capacitance onto $Al_2O_3$ substrate. The capacitance was 0.9pF. Also Dielectric constant was been 351 at 100 mTorr and annealing temperature $750^{\circ}C$ for 1 hour. The loss tangent was been 0.00531.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.2
• /
• pp.305-311
• /
• 1999

In this paper, it is designed a new type single layer patch antenna which is printed on a very thin film and separated from the ground-plane by foam with a low permitivity of 1.06 and a high thickness of around quarter wavelength. It allows the use of three-dimensional transition, from one level to another, so that its bandwidth can be enhanced by wideband impedance matching. The radiation pattern, return loss, and VSWR of the antenna are calculated using "IE3D" simulation package, and compared with the experimental results. Experimental results show that the bandwidth is about 65% of center frequency 6.8 GHz, return loss and VSWR are in a fairly good agreement with the calculations.culations.