• Journal of Sensor Science and Technology
• /
• v.32 no.3
• /
• pp.140-146
• /
• 2023

Water quality is crucial for human health and the environment. Accurate measurement of the quantity of organic carbon in water is essential for water quality evaluation, identification of water pollution sources, and appropriate implementation of water treatment measures. Total organic carbon (TOC) analysis is an important tool for this purpose. Although other methods, such as chemical oxygen demand (COD) and biochemical oxygen demand (BOD) are also used to measure organic carbon in water, they have limitations that make TOC analysis a more favorable option in certain situations. For example, COD requires the use of toxic chemicals, and BOD is time-consuming and can produce inconsistent and unreliable results. In contrast, TOC analysis is rapid and reliable, providing accurate measurements of organic carbon content in water. However, common methods for TOC analysis can be complex and energy-intensive because of the use of high-temperature heaters for liquid-to-gas phase transitions and the use of acid, which present safety risks. This study focuses on a TOC analysis method using TiO₂ photocatalysis, which has several advantages over conventional TOC analysis methods, including its low cost and easy maintenance. For TiO₂, rutile and anatase powders are mixed with an inorganic binder and spray-coated onto a glass fiber substrate. The TiO₂ powder and inorganic binder solutions are adjusted to optimize the photocatalytic reaction performance. The TiO₂ photocatalysis method is a simple and low-power approach to TOC analysis, making it a promising alternative to commonly used TOC analysis methods. This study aims to contribute to the development of more efficient and cost-effective approaches for water quality analysis and management by exploring the effectiveness and reliability of the developed equipment.

• Korean Journal of Materials Research
• /
• v.33 no.7
• /
• pp.285-294
• /
• 2023

Porous ceramics are used in various industrial applications based on their physical properties, including isolation, storage, and thermal barrier properties. However, traditional manufacturing environments require additional steps to control artificial pores and limit deformities, because they rely on limited molding methods. To overcome this drawback, many studies have recently focused on fabricating porous structures using additive manufacturing techniques. In particular, the binder jet technology enables high porosity and various types of designs, and avoids the limitations of existing manufacturing processes. In this study, we investigated process optimization for manufacturing porous ceramic filters using the binder jet technology. In binder jet technology, the flowability of the powder used as the base material is an important factor, as well as compatibility with the binder in the process and for the final print. Flow agents and secondary binders were used to optimize the flowability and compatibility of the powders. In addition, the effects of the amount of added glass frit, and changes in sintering temperature on the microstructure, porosity and mechanical properties of the final printed product were investigated.

• Korean Journal of Materials Research
• /
• v.34 no.3
• /
• pp.175-183
• /
• 2024

Geopolymer, also known as alkali aluminum silicate, is used as a substitute for Portland cement, and it is also used as a binder because of its good adhesive properties and heat resistance. Since Davidovits developed Geopolymer matrix composites (GMCs) based on the binder properties of geopolymer, they have been utilized as flame exhaust ducts and aircraft fire protection materials. Geopolymer structures are formed through hydrolysis and dehydration reactions, and their physical properties can be influenced by reaction conditions such as concentration, reaction time, and temperature. The aim of this study is to examine the effects of silica size and aging time on the mechanical properties of composites. Commercial water glass and kaolin were used to synthesize geopolymers, and two types of silica powder were added to increase the silicon content. Using carbon fiber mats, a fiber-reinforced composite material was fabricated using the hand lay-up method. Spectroscopy was used to confirm polymerization, aging effects, and heat treatment, and composite materials were used to measure flexural strength. As a result, it was confirmed that the longer time aging and use of nano-sized silica particles were helpful in improving the mechanical properties of the geopolymer matrix composite.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.6
• /
• pp.852-857
• /
• 2010

This study was performed to explore the effect of the clay mineral illite on the improvement of bed soil and plant growth. Red pepper (Capsicum annuum L.) was used as a model vegetable crop. The experiment was performed during the whole six weeks in the glass house of the Chungbuk National University. Its seedlings were cultivated in the bed soil normally used for horticultural purpose. Of the seedlings cultured, the healthy and regular size of seed were selected and cultivated in the pots. They were treated with two forms of illite, particulate (PA) and powder (PW), at the following application rates: standard application[P1 (PA1, PW1), 1:20 (w/w)], two times[P2 (PA2, PW2), 1:10 (w/w)], and four times[P4 (PA4, PW4), 1:5 (w/w)] of standard application. Untreatment (P0) was used as a control pot. At six weeks of cultivation, their growth lengths were correspondingly increased as the application rate was increased ranging from P0, P1, P2, and to P4. Their growth length was a little greater on the application of powder illite (PW) than on the particulate illite (PA). Based on the plant analysis for the root, leaf, stem of red pepper, the uptake amounts of K, Ca, and Mg, were correspondingly increased, as the application rate was increased ranging from P0, P1, P2, and to P4, respectively. At the same application rate, their amounts taken up in the respective parts were higher on the application of PW illite than on the PA one. Especially the amounts of Ca and Mg were higher in the stem, leaf than root. Consequently, it appears that the illite treatment, especially, PW form of illite, enhance the growth of red pepper in the glass house during the whole six weeks of experiment.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.2
• /
• pp.60-64
• /
• 2011

High sensitivity IR image sensors require materials characteristics with temperature coefficient of resistance (TCR) and IR range absorption. In this study, the metal-dielectric thermo sensitive films (MDTF) based on $(SiO_2)_x-(Ti)_y$ composition were deposited on substrates of germanium and glass by thermal evaporator. The $SiO_2$ : Ti mixture was made from the ratio of 9 : 1, 8 : 2, 7 : 3, 6 : 4, respectively. $(SiO_2)_x-(Ti)_y$ mixture powder was loaded on tungsten boat in evaporator and was 15.5 cm from the substrate. Resistance of $(SiO_2)_x-(Ti)_y$ in the range of 273~333K were measured as a function of temperature. Temperature coefficient of resistance (TCR) was calculated by the resistance variation. Under the various mixture ratios condition, it is possible to obtain $SiO_2$-Ti layers with resistance from units kilo-ohm to hundreds kilo-ohm. Finally, our results showed that Temperature coefficient of resistance (TCR) of these films varies from -1.4 to $-2.6%K^{-1}$.

• Journal of Sensor Science and Technology
• /
• v.9 no.2
• /
• pp.146-152
• /
• 2000

Lithium doped zinc oxide(ZnO:Li) films are prepared by rf magnetron sputtering on Corning 7059 glass substrate using specifically designed ZnO targets containing different amount of $Li_2CO_3$ powder as the Li doping source. The structural properties of the Li doped ZnO films are investigated by XRD, SEM and AFM. The electrical properties of the ZnO:Li films are measured for various deposition conditions, such as the substrate temperature, $O_2$/Ar gas ratio and rf power. The effects of the $Li_2CO_3$ content in target and the deposition conditions on the structural and electrical properties were studied. When ZnO:Li films were sputtered at the substrate temperature of $200^{\circ}C$, $O_2$/Ar gas ratio of 100% and rf power of 100W with a target containing less than 1wt% content of $Li_2CO_3$, showed good surface morphology, strong c-axis orientation and high resistivity of more than $10^8{\Omega}cm$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.4
• /
• pp.158-163
• /
• 2011

$CuInS_2$ thin films were prepared using a sol-gel spin-coating method. That makes large scale substrate coating, simple equipment, easy composition control available. The structural and optical properties of $CuInS_2$ thin films that include less toxic materials (S) instead of Se, tetragonal chalcopyrite structure. Copper acetate monohydrate ($Cu(CH_3COO)_2{\cdot}H2O$) and indium acetate ($In(CH_3COO)_3$) were dissolved into 2-propanol and l-propanol, respectively. The two solutions were mixed into a starting solution. The solution was dropped onto glass substrate, rotated at 3000 rpm, and dried at $300^{\circ}C$ for Cu-In as-grown films. The as-grown films were sulfurized inside a graphite container box and chalcopyrite phase of $CuInS_2$ was observed. To determine the optical properties measured optical transmittance of visible light region (380~770 nm) were less than 30 % in the overall. The XRD pattern shows that main peak was observed at Cu/In ratio 1.0 and its orientation was (112). As annealing temperature increases, the intensity of (112) plane increases. The unit cell constant are a = 5.5032 and c = 11.1064 $\AA$, and this was well matched with JCPDS card. The optical transmittance of visible region was below than 30 %.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.2
• /
• pp.39-46
• /
• 2013

In this paper, organic solar cells(OSCs) based on bulk-heterojunction structures were fabricated by spin coating method using polymer P3HT and fullerene PCBM as a photoactive layer. The fabricated OSCs had a simple glass/ITO/PEDOT:PSS/P3HT:PCBM/Al structures. The photoactive layer of mixed P3HT:PCBM was formed with 1:1 weight ratio. The hole transport layer(HTL) was used conducting polymer PEDOT:PSS concentration with gold nanoparticles. The annealing temperature and concentration of nanoparticles in HTL were verified to improve the OSC characterization. The percentage of gold nanoparticles in HTL were 0.5 wt% and 1.0 wt%, and the surface morphology, electrical properties and absorption intensities were investigated. The devices were 0.5 wt%, and the highest 3.1% of the powder conversion efficiency(PCE), 10.2 $mA/cm^2$ of the maximum short circuit current density($J_{SC}$), 0.535V of the open circuit voltage($V_{OC}$) and 55.8% of the fill factor(F.F) could be obtained when the nanoparticle concertration was 0.5 wt%. The annealing temperature of HTL was $110^{\circ}C$, $130^{\circ}C$, $150^{\circ}C$ in vacuum oven and measured the absorption intensities, surface morphology, crystallinity and electrical properties were investigated. The best property was obtained in HTL annealed at $130^{\circ}C$ for gold nanoparticles of 0.5 wt%, showing that $J_{SC}$, $V_{OC}$, F.F and PCE were about 12.0 $mA/cm^2$, 0.525V, 64.2% and 4.0%, respectively.

• Journal of the Korean Ceramic Society
• /
• v.42 no.2 s.273
• /
• pp.132-139
• /
• 2005

Sintering behavior of $BaO-Nd_{2}O_3-TiO_2$ with a Pb-based glassceramics frit were investigated in order to understand an effect of glassceramics as a low temperature sintering agent on dielectric ceramics. A green sheet form was fabricated through tape casting method with the glassceramic fut added $BaO-Nd_{2}O_3-TiO_2$. The dispersion properties, rheological properties and final density of dielectric composit slurry as a function of amount and composition of organic additives was examined. The dispersants' addition was effective in controlling dispersion of the ceramics in solution. The addition of excessive dispersant showed adverse effect on dispersion. The prepared slurries, containing ceramic : powders, glass-ceramics and various kinds of organic viechles, exhibited typical shear thinning behavior. The best properties of tape casting appeared powder to solvent ratio 65 : 35 and amount of the binder 6 wt$\%$ and plasticizer 3 wt$\%$. The viscosity of the slurry was 677 cps and green/sintered density in the tape was $3.3 g/cm^3,\;5.56 g/cm^3$ respectively.

• Journal of the Korean GEO-environmental Society
• /
• v.19 no.5
• /
• pp.5-12
• /
• 2018

The porosity formation by the addition of additives was found to be the highest in the case of aluminum powder 3% and $Ca(OH)_2$ 2% under the condition that strength was maintained. The optimum mixing ratio of the binder was shown to be the most effective at (Ash+Food waste+clay):(water glass+colloidal silica) 7:3, and the temperature response is most economical and effective at $1,000^{\circ}C$. The optimal mixing ratio is the strength in 30% of ash, 30% of clay and 10% of food waste, which is the effective in non-point pollution water treatment. Filter media produced under optimal mixing conditions were analyzed as $SiO_2$ 65.8%, density $1.4g/cm^3$, porosity 25.6%, pH 9.8, and no hazardous substances were detected. As a result of the filtration of the water treatment, the mean concentration of the filtered SS was $14.06mg/{\ell}$, and the removal efficiency of SS was 90%, the recovery rate of the reversal is 97.1%. This enables the development of filter media considering economic efficiency and efficiency as well as the utilization of waste resources, enabling high value added of waste resources.