• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38A no.10
• /
• pp.874-884
• /
• 2013

This paper presents in details channel and noise characteristics over narrow bands below 500kHz based on the field tests over underground low voltage(LV) power lines in residential areas in Korean grid. We show that the channel characteristics of narrowband signals over underground LV power line are decent. We first describe methodology of channel characteristic measurements including channel frequency response, noise, and line impedance, and obtain channel characteristics over the underground LV lines in the residential areas. Also based on the measurement results, we adopt the IEEE P1901.2 standard on the FCC High band, and bring up narrow band power line communication network.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.10 s.89
• /
• pp.1011-1017
• /
• 2004

Ultra Wideband(UWB) technologies have been developed to exploit a new spectrum resource in substances and to realize ultra-high-speed communication, high precision geolocation, and other applications. The energy of UWB signal is extremely spread from near DC to a few GHz. This means that the interference between conventional narrowband systems and UWB systems is inevitable. However, the interference effects had not previously been studied from UWB wireless systems to conventional mobile wireless systems sharing the frequency bands such as Korean Cellular CDMA and WCDMA. This paper experimentally evaluates the interference from two kinds of UWB sources, namely a direct-sequence spread-spectrum CDMA(DS-CDMA) UWB source and an impulse radio UWB source, to a Cellular CDMA and WCDMA digital transmission system. The average frame error rate degradation of each system are presented. From these experimental results, the interference effects of DS-CDMA UWB source is not severe compared to the Impulse UWB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.7
• /
• pp.1131-1137
• /
• 1999

In this paper, a novel design method of an apertured coupled microstrip patch antenna with the single feeding structure is proposed for dual resonance frequencies with mutually perpendicular polarizations. The characteristics of this antenna are experimentally investigated. In order to achieve this goal, a new type of square patch with double notches is used as a radiator and the crossed slot and the bended mictrostrip feeder are adopted for the dual polarizations in the aperture-coupled structure. For the application of the proposed antenna, a Ku-band Tx/Rx $2\times$ subarray antenna is designed and manufactured. Also, the applicability of the antenna as a ground terminal is examined through performance analysis. According to the measurement, the gain of the antenna is 10dBi at the center frequencies of Tx and Rx, the side lobe level is lower than -13dB, and the cross polarization lebel is below 17 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.7
• /
• pp.998-1009
• /
• 1999

In this paper, a microstrip aperture-patch antenna and a microstrip ring antenna, which have single microstrip line feeding systems for the circular polarization, are designed, and experimental results are presented at X-band. The microstrip aperture-patch antenna is characterized by its wide operating frequency range, and the microstrip ring antenna is suitable for a basic radiator in the large array antenna due to its small size. Several design parameters for these antennas are considered and analyzed to improve antenna characteristics such as VSWR bandwidth and axial ratio. Initially, the sizes of the aperture and ring radiator are determined on a basis of the cavity model, then shapes of the patch within the aperture and the inner stub of the ring are optimized using Ensemble software. Measurement results show that the aperture-patch antenna has 25% of VSWR bandwidth and 1.2dB of axial ratio at the boresight, and the ring antenna has 6.7% of VSWR bandwidth and 1.6dB of axial ratio at the boresight.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.1 s.116
• /
• pp.1-6
• /
• 2007

This paper presents an equal 3-way planar-type power divider. In conventional 3-way Wilkinson dividers, it has been difficult to realize the circuit because of the crossover of isolation resistors. In the proposed divider, the isolation resistors can be easily attached to the planar structure of the divider. In addition, no phase difference is observed at output ports without extra line compensation because of its symmetric structure. The fabricated 3-way divider has a greatly improved bandwidth by 160 % in $S_{11}$, 22.4 dB, min of isolation, and in phase characteristics between output ports at 2.4 GHz of center frequency from measurement.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.1 s.116
• /
• pp.44-52
• /
• 2007

In this paper, An active antenna of T-DMB was developed to equip to handhold gadgets by using LNA and a parasitic element allowing to miniature. The size of the fabricated active antenna is $80{\times}6{\times}0.4\;mm$ and FR4 is used for the substrate. The size of the proposed antenna is reduced by 38.8% at the operating frequency compared to one without a parasitic element, and a short stub. The proposed antenna shows improved performance at the measurement especially in the ratio of S/N compared with conventional monopole of 300 mm. The proposed antenna is well able to adapt into handhold gadgets for receiving T-DMB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.5 s.120
• /
• pp.539-546
• /
• 2007

In this paper, a 3-D EM simulation methodology for on-chip spiral inductor analysis has provided and it is shown that the methodology can be adapted to the highly predictable design for CMOS VCO. LC-resonator type VCO have fabricated by using standard 0.25 um CMOS process. And the LC VCO layout case which has pattern ground shielded inductors and the other layout case which has no pattern grounded inductors were fabricated for the verification of their effects on the VCO's phase noise by reducing the Q-factor of inductors. Fabricated VCO has 3.094 GHz, -12.15 dBm output at the tuning voltage of 2.5 V, and from the simulation, Q-factor of the pattern grounded inductor has increased 8% at 3 GHz, and from the measurement results, the phase noise has reduced by 9 dB at the 3 MHz off-set frequency for the pattern grounded inductor layout case.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.4
• /
• pp.342-349
• /
• 2016

We design a displaced-axis Gregorian dual antenna in the form of a metal reflectarray antenna for millimeter wave region, W-band. Unlike a reflectarray composed of printed patch antennas on a dielectric substrate, metallic rectangular waveguide unit-cells are proposed to avoid the loss of substrate and take an advantage of ease of typical metal machining fabrication. In this paper, the radiation characteristics of constructed metal reflectarray antennas show ultra high-gain antenna over 50 dBi at a target frequency in W-band. The experimental measurements are conducted in millimeter-wave compact range antenna measurement system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.7
• /
• pp.694-700
• /
• 2013

Urban area is a representative environment of wireless channels in the mobile communication, building density has a different distribution depending on the location. Building density has affect to propagation prediction For this reason, building density is expected to affect to the channel characteristics, we need to analyze it. We measured channel characteristics in urban areas of Jeju island by channel sounder and $4{\times}4$ antenna. Channel characteristics considering the building density were derived based on the measured data in the urban area. In this paper, the measurement data is analyzed and channel characteristics are derived through MIMO Channel measurements at 700 MHz considering the building density in the urban area.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.10
• /
• pp.917-925
• /
• 2016

Schmitt Trigger logic is a gate level design method to have hysteresis characteristics to improve noise immunity in digital circuits. Dynamic Threshold voltage MOS(DTMOS) Schmitt trigger circuits can improve noise immunity without adding additional transistors but by controlling substrate bias. The performance of DTMOS Schmitt trigger logic has not been verified yet in standard CMOS process through measurement. In this paper, DTMOS Schmitt trigger logic was implemented and verified using Magna $0.18{\mu}m$ MPW process. DTMOS Schmitt trigger buffer, inverter, NAND, NOR and simple digital logic circuits were made for our verification. Hysteresis characteristics, power consumption, and delay were measured and compared with common CMOS logic gates. EM Immunity enhancement was verified through Direct Power Injection(DPI) noise immunity test method. DTMOS Schmitt trigger logics fabricated using CMOS process showed a significantly improved EM Immunity in 10 M~1 GHz frequency range.