• Transactions on Electrical and Electronic Materials
• /
• v.3 no.2
• /
• pp.16-19
• /
• 2002

In this study, a novel red emitting organic electroluminescent (EL) device was fabricated with the bis(8-oxyquinolino)zinc II (Znq2) doped dye as an emitting layer. The Znq2 was synthesized successfully from zinc chloride (ZnC1$_2$) as an initial material. Then, we fabricated the red organic EL device with a dye (DCJTB) doped and inserted Znq2 between emission layer and cathode for increasing EL efficiency. The hole transporting layer is a N,N'-diphenyl-N,N'-bis-(3-methylphenyl)-1,1'-diphenyl-4,4-diamine (TPD), and the host material of emission layer is Znq2. And the electrical and luminance characteristics of the device were measured. We found that the EL device with Znq2 inserting layer results in the increasing luminance efficiency.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.1
• /
• pp.32-35
• /
• 2011

Top-emission device has a merit of high aperture ratio and narrow emission spectrum compared to that of bottom-emission one. Emission spectra of top-emission organic light-emitting diodes depending on a layer thickness and view angle were analyzed using a theory of microcavity. Device structure was manufactured to be Al (100 nm)/TPD/$Alq_3$/LiF (0.5 nm)/Al (2 nm)/Ag (30 nm). N,N'-diphenyl-N,N'- di (m-tolyl)-benzidine (TPD) and tris (8-hydroxyquinoline) aluminium (Alq3) were used as a hole-transport layer and emission layer, respectively. And a thickness of TPD and Alq3 layer was varied in a range of 40 nm~70 nm and 60 nm~110 nm, respectively. Angle-dependent emission spectrum out of the device was measured with a device fixed on a rotating plate. Since the top-emission device has a property of microcavity, it was observed that the emission spectrum shift to a longer wavelength region as the organic layer thickness increases, and to a shorter wavelength region as the view angle increases. Layer thickness and view-angle dependent emission spectra of the device were analyzed in terms of microcavity theory. A reflectivity of semitransparent cathode and optical path length were deduced.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.08a
• /
• pp.101-104
• /
• 2002

Abstract We give pressure stimulation into organic thin films and then manufacture a device under the accumulation condition that the state surface pressure is 10[mN/m]. In processing of a device manufacture, we can see the process is good from the change of a surface pressure for organic thin films and transfer ratio of area per molecule. The structure of manufactured device is Au/Poly-${\gamma}$ Benzyl $_D$-Glutamate/Al; the number of accumulated layers is 1, 3, 5 and 7. Also, we then examined of the MIM device by means of I-V. The I-V characteristic of the device is measured from 0 to +2[V]. We determined electrochemical measurement by using cyclic voltammetry with a three-electrode system. LB film accumulated by monolayer on an ITO. In the cyclicvoltammetry, An Ag/AgCl reference electrode, a platinum wire counter electrode and LB film-coated ITO working electrode measured in $LiBF_4$ solution, stable up to 0.9V vs. Ag/AgCl.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.05a
• /
• pp.873-875
• /
• 2014

In this paper, we propose the access control system based bluetooth using the MAC address of the smart device. Access control system that propose compares the smart device MAC address entry and exit and MAC address that is registered with the server. Depending on whether the match was compared, access control is performed. Result of the experiment, control of door is possible only by bluetooth pairing of the bluetooth module and smart device. Therefore, it does not require access to another tool.In addition, Action for access approval is omitted. Therefore, the access authorization procedure is simplified compared to existing access control systems, it is possible to improve the convenience.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.961-962
• /
• 2008

This paper proposes a touchless fingerprint acquisition device for five fingerprints. In conventional devices, they are focused for taking 1 touchless fingerprint image. But this device is taking 5 fingerprint image at a time. Also, it considers problems for focus and rolling in touchless fingerprint recognition for using camera. They affects fingerprint recognition, so this research is performed to measure and analyze these problems.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.2
• /
• pp.305-311
• /
• 2003

This Paper Presents an information about the heat transfer characteristics of a separate type thermosyphon in electronic equipments. The heat removal problem of electronic equipments is regarded as an important factor and a separate type heatpipes can be utilized as a cooling device of electronic equipments (such as CPU of a Personal computer or notebook). In this study. heat source ($50\times50\times2 mm $aluminum Pseudo CPU) was used for the experiment. The device can transfer heat from the evaporator to the condenser through natural circulation (without any external driving forces) and the results indicate that the device is capable of dissipating over 60W of thermal energy and keeping the heating plate surface temperature under $50^{\circ}C$.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.239-242
• /
• 1999

In this paper, we report the process/device design of high-speed, high-voltage SOI smart power IC for mobile communication system, high-speed HDD system and the electronic control system of automobiles. The high voltage LDMOS with 70V breakdown voltage under 0.8${\mu}{\textrm}{m}$ design rule, the high voltage bipolar with 40V breakdown voltage for analog signal processing, the high speed bipolar with cut-off frequency over 20㎓ and LDD NMOS for high density were proposed and simulated on a single chip by the simulator DIOS and DESSIS. And we extracted the process/device parameters of the simulated devices.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.2
• /
• pp.83-87
• /
• 2020

In this letter, we propose and analyze a new asymmetric structure that can be used for next-generation power semiconductor devices. We compare and analyze the electrical characteristics of the proposed device with respect to those of symmetric devices. The proposed device has a p-emitter on the right side of the cell. The peak electric field is reduced by the shielding effect caused by the p-emitter structure. Consequently, the breakdown voltage is increased. The proposed asymmetric structure has an approximately 100% higher Baliga's figure of merit (~94.22 MW/㎠) than the symmetric structure (~46.93 MW/㎠), and the breakdown voltage of the device increases by approximately 70%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.16-17
• /
• 2005

Local lifetime control by ion implantation has become an useful tool for production of modern power devices. In this work, punch-through diodes were irradiated with protons for the high speed power diode fabrication. Proton irradiation was executed at the various energy and dose conditions. Characterization of the device was performed by I-V, C-V and Trr measurement. We obtained enhanced reverse recovery time characteristics which was about 45% of original device and about 73% of electron irradiated device. The measurement results showed that proton irradiation was able to effectively reduce minority carrier lifetime.

• The Journal of the Korean dental association
• /
• v.15 no.12
• /
• pp.1027-1030
• /
• 1977

It has been widely believed that the exact measurement of the forces exerted on teeth and its structures by the lingual and perioral musculatures such as lip, cheek and tongue is important and significant in dentistry. Such measuring, moreover, is highly emphasized the importance of the fact that it can be of much help to study the physiological function displayed in the oral cavity. Recognizing the importance of measuring the pressures, the author has devised an electronic device consisting of pressure transducers utilizing reistance-strnain gauges. This electronic strain gauge was very easy to manipulate and its scale error was extremely minimized, unaffected by mouth temperature, mosture and external forces Author was able to read its results with attached meter without using calibration chart. Futhermore, the sensitivity of this electronic device was extremely high, Thus it facilitated to measure a force from 0 to 230 grams.