• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.180-181
• /
• 2015

본 논문에서는 ICP Poly Etcher를 이용한 Dry Etch에서 몇가지 공정조건의 변화에 따른 Etching 특성 변화를 연구하였다. 주요 가스유량들이 증가 할 때, Poly-Si 의 Etch rate는 증가 하였으며 Uniformity는 나빠진 것을 확인 할 수 있었고 다른 특성들은 특별한 변화를 보이지 않았다. 주요 Gas인 HBr의 증가는 PR(Photo Resist)와 Uniformity에 영향을 주었다. 이 논문을 통해 HBr의 유량이 Poly-Si Etching에 영향을 주는 결과를 알아 볼 수 있었고 HBr 가스의 유량 증가가 Polymer의 생성에 영향을 줘 Selectivity와 Uniformity를 증가 시킨다는 것도 확인 해 볼 수 있었다.

• Journal of the Korean Electrochemical Society
• /
• v.16 no.1
• /
• pp.1-8
• /
• 2013

This review article summarizes metal-assisted chemical etching (MAC etch or MACE), an anisotropic etching method for Si, and describes principles, main factors, and recent achievements in literature. In 1990, it was discovered that, with metal catalyst on surface and $H_2O_2$/HF as etchant, Si substrate can be etched anisotropically, in even in solution. In contrast to high-cost vacuum-based dry etching methods, MAC etch enables to fabricate a variety of high aspect ratio nanostructures through wet etching process.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.4
• /
• pp.305-310
• /
• 2008

Deep trench etching of silicon was investigated as a function of RF source power, DC bias voltage, $C_4F_8$ gas flow rate, and $O_2$ gas addition. On increasing the RF source power from 300 W to 700 W, the etch rate was increased from $3.52{\mu}m/min$ to $7.07{\mu}m/min$. The addition of $O_2$ gas improved the etch rate and the selectivity. The highest etch rate is achieved at the $O_2$ gas addition of 12 %, The selectivity to PR was 65.75 with $O_2$ gas addition of 24 %. At DC bias voltage of -40 V and $C_4F_8$ gas flow rate of 30 seem, We were able to achieve etch rate as high as $5.25{\mu}m/min$ with good etch profile.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.213-216
• /
• 2001

Etching behaviors of ferroelectric YMn $O_3$ thin films were studied by an inductively coupled plasma (ICP). Etch characteristic on ferroelectric YMn $O_3$ thin film have been investigated in terms of etch rate, selectivity and etch profile. The maximum etch rate of YMn $O_3$ thin film is 300 $\AA$/min at Ar/C $l_2$ of 2/8, RF power of 800W, dc bias voltage of 200V, chamber pressure of 15mTorr and substrate temperature of 3$0^{\circ}C$. Addition of C $F_4$ gas decrease the etch rate of YMn $O_3$ thin film. From the results of XPS analysis, Y $F_{X}$ compunds were found on the surface of YMn $O_3$ thin film which is etched in Ar/C1/C $F_4$ plasma. The etch profile of YMn $O_3$ film is improved by addition of C $F_4$ gas into the Ar/C $l_2$ plasma. These results suggest that fluoride yttrium acts as a sidewall passivants which reduce the sticking coefficient of chlorine on YMn $O_3$.>.

• Applied Chemistry for Engineering
• /
• v.17 no.3
• /
• pp.327-330
• /
• 2006

We investigated the usefulness of $NbO_{x}$ nanopillars as an etching mask of dry etching for the formation of Si nanodot arrays. The $NbO_{x}$ nanopillar arrays were prepared by the anodic aluminum oxidation process of Al and Nb thin films. The etch rate and etch profile of $NbO_{x}$ nanopillar arrays were examined by varying the experimental conditions such as the concentration of etch gas, coil rf power, and dc bias voltage in the reactive ion etch system using the inductively coupled plasma. As the concentration of $Cl_{2}$ gas increased, the etch rate of $NbO_{x}$nanopillars decreased. With increasing coil rf power and dc bias voltage, the etch rates were found to increase. The etch characteristics and etch mechanism of $NbO_{x}$ nanopillars were investigated by varying the etch time under the selected etch conditions.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1999.11a
• /
• pp.89-89
• /
• 1999

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.4
• /
• pp.216-220
• /
• 2013

The etching characteristics of indium zinc oxide (IZO) in $Cl_2/Ar$ plasma were investigated, including the etch rate and selectivity of IZO. The IZO etch rate showed non-monotonic behavior with increasing $Cl_2$ fraction in the $Cl_2/Ar$ plasma, and with increasing source power, bias power, and process pressure. In the $Cl_2/Ar$ (75:25%) gas mixture, a maximum IZO etch rate of 87.6 nm/min and etch selectivity of 1.09 for IZO to $SiO_2$ were obtained. Owing to the relatively low volatility of the by-products formation, ion bombardment was required, in addition to physical sputtering, to obtain high IZO etch rates. The chemical state of the etched surfaces was investigated with X-ray photoelectron spectroscopy. These data suggested that the IZO etch mechanism was ion-enhanced chemical etching.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.6
• /
• pp.451-455
• /
• 1999

The highest etch rate of Pt film was obtained at 10% $Cl_2$/90% Ar gas mixing ratio in our previous investigation. However, the problems such as the etch residues(fence) remained on the pattern sidewall, low selectivity to oxide as mask and low etch slope were presented. In this paper, the etching by additive $O_2$ gas to 10% $Cl_2$/90% Ar gas base was examined. As a result, the fence-free pattern and higher etch slope as about 60$^{\circ}$was observed and the selectivity to oxide increased to 2.4 without decreasing of the etch rate $1500{\AA}$/min. XPS surface analysis proved that a only little $O_2$ gas removes the Pt-CI compounds as residues on the etched surface.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.75-79
• /
• 2003

We studied InP etch results in high density planar inductively coupled $BCl_3$ and $BCl_3$/Ar plasmas. The investigated process parameters were ICP source power, RIE chuck power, chamber pressure and $BCl_3$/Ar gas composition. It was found that increase of ICP source power and RIE chuck power raised etch rate of InP, while that of chamber pressure decreased etch rate. Etched InP surface was clean and smooth (RMS roughness < 2 nm) with a moderate etch rate ($300\;{\sim}\;500\;{\AA}/min$) after the planar $BCl_3/Ar$ ICP etching. It may make it possible to open a new regime of InP etching with $CH_4/H_2$ - free plasma chemistry. Some amount of Ar addition (< 50%) also improved etch rates of InP, while too much Ar addition reduced etch rates of InP.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.2
• /
• pp.67-70
• /
• 2013

In this study, we changed the input parameters (gas mixing ratio, RF power, DC bias voltage, and process pressure), and then monitored the effect on TiN etch rate and selectivity with $SiO_2$. When the RF power, DC-bias voltage, and process pressure were fixed at 700 W, - 150 V, and 15 mTorr, the etch rate of TiN increased with increasing $CF_4$ content from 0 to 20 % in $CF_4$/Ar plasma. The TiN etch rate reached maximum at 20% $CF_4$ addition. As RF power, DC bias voltage, and process pressure increased, all ranges of etch rates for TiN thin films showed increasing trends. The analysis of x-ray photoelectron spectroscopy (XPS) was carried out to investigate the chemical reactions between the surfaces of TiN and etch species. Based on experimental data, ion-assisted chemical etching was proposed as the main etch mechanism for TiN thin films in $CF_4$/Ar plasma.