• Journal of Satellite, Information and Communications
• /
• v.8 no.1
• /
• pp.45-53
• /
• 2013

An electrostatic discharge (ESD) protection device, so called, N-type extended drain silicon controlled rectifier (NEDSCR) device, was analyzed for high voltage I/O applications. A conventional NEDSCR device shows typical SCR-like characteristics with extremely low snapback holding voltage. This may cause latch-up problem during normal operation. However, a modified NEDSCR device with proper junction/channel engineering using counter pocket source (CPS) ion implantation demonstrates itself with both the excellent ESD protection performance and the high latch-up immunity. Since the CPS implant technique does not change avalanche breakdown voltage, this methodology does not reduce available operation voltage and is applicable regardless of the operation voltage.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.6
• /
• pp.593-596
• /
• 2015

In this paper, we design a high efficiency class E power amplifier operating at low drain bias voltage for wireless power transfers. A 13.56 MHz power amplifier is designed at drain bias voltage of 12.5 V using Si MOSFET with the breakdown voltage of 40 V. High quality-factor solenoidal inductor is designed and fabricated for use in output matching circuit to improve output power and efficiency. Input matching circuit simply consists of resistor and inductor to reduce the circuit area and improve the stability. The fabricated power amplifier shows the measured output power of 38.6 dBm with the gain of 16.6 dB and power added efficiency of 89.3 % at 13.56 MHz.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.295-298
• /
• 1999

AlGaAs/InGaAs power P-HEMTS (Pseudo-morphic High Electron Mobility Transistors) with 1.0-${\mu}{\textrm}{m}$ gate length for PCS applications have been fabricated. We adopted single heterojunction P-HEMT structure with two Si-delta doped layer to obtain higher current density. It exhibits a maximum current density of 512㎃/mm, an extrinsic transconductance of 259mS/mm, and a gate to drain breakdown voltage of 12.0V, respectively. The device exhibits a power density of 657㎽/mm, a maximum power added efficiency of 42.1%, a linear power gain of 9.85㏈ respectively at a drain bias of 6.0V, gate bias of 0.6V and an operation frequency of 1.765㎓.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1606-1608
• /
• 1996

An the SOI RESURF LDMOS with a taper oxide on the drain is proposed and verified by the device simulator, MEDICI. Simulation results on the proposed LDMOS exhibits the increase in the breakdown voltage by 12 % and reduction in the drift region length by 25 %.

• Electrical & Electronic Materials
• /
• v.7 no.3
• /
• pp.225-230
• /
• 1994

In this paper, we have fabricated short channel MOSFETs with these parameters to verify the validity of process parameters extraction by DTC method. The experimental results of fabricated short channel devices according to the optimal process parameters demonstrate good device characteristics such as good drain current-voltage characteristics, low body effects and threshold voltage of$\leq$+-.1.0V, high punch through and breakdown voltage of$\leq$12V, low subthreshold swing(S.S) values of$\leq$105mV/decade.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12
• /
• pp.1065-1070
• /
• 2003

HTO(High Temperature Oxide) films are mainly used as a gate insulator for polysilicon thin film transistors(Poly-Si TFT's). The HTO films, however, show the demerits of a high leakage current and a low electric breakdown voltage comparing with conventional thermal oxides even though they have a better surface in roughness than the thermal oxides. In this paper, we propose an ONO(Oxide-Nitride-Oxide) multilayer as the gate insulator for poly-Si TFT's. The leakage current and electric breakdown voltage of the ONO and HTO were measured. The drain current variation of poly-Si TFT's with a variety of gate insulators was observed. The thickness optimization in ONO films was carried out by studying I$\_$on/I$\_$off/ ratio of the poly-Si TFT's as a function of the thickness of ONO film adopted as gate insulator.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.1057-1060
• /
• 2003

This paper is about the optimized fabricated parameter in the EDMOSFET(Extended drain MOSFET) with a various temperature. As we know, the two important factors of EDMOSFET parameters are breakdown voltage and on Resistance. So, we have aims of the power EDMOSFET design to have high breakdown voltage and low on resistance. Thus in this paper, we will show the figure of merit in LDMOS (BV/Ron) in accordance with increase in temperature(300K-500K, step:50K), and measure electronic characteristics of power EDMOSFET. As a result, the important factors in design of EDMOS are temperature and Lg.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.3
• /
• pp.964-969
• /
• 2014

In Super Junction MOSFET, Charge Balance is the most important issue of the trench filling Super Junction fabrication process. In order to achieve the best electrical characteristics, the N type and P type drift regions must be fully depleted when the drain bias approaches the breakdown voltage, called Charge Balance Condition. In this paper, two methods from the fabrication process were used at the Charge Balance condition: Trench angle decreasing process and Bottom implantation process. A lower on-resistance could be achieved using a lower trench angle. And a higher breakdown voltage could be achieved using the bottom implantation process. The electrical characteristics of manufactured discrete device chips are compared with those of the devices which are designed of TCAD simulation.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.6
• /
• pp.193-195
• /
• 2009

This paper aims to develop a low gate source voltage ($V_{gs}$) N-LDMOS element that is fully operational at a CMOS Logic Gate voltage (3.3 or 5 V) realized using the 0.35 μm BCDMOS process. The basic structure of the N-LDMOS element presented here has a Low $V_{gs}$ LDMOS structure to which the thickness of a logic gate oxide is applied. Additional modification has been carried out in order to obtain features of an improved breakdown voltage and a specific on resistance ($R_{sp}$). A N-LDMOS element can be developed with improved features of breakdown voltage and specific on resistance, which is an important criterion for power elements by means of using a proper structure and appropriate process modification. In this paper, the structure has been made to withstand the excessive electrical field on the drain side by applying the double gate oxide structure to the channel area, to improve the specific on resistance in addition to providing a sufficient breakdown voltage margin. It is shown that the resulting modified N-LDMOS structure with the feature of the specific on resistance is improved by 31%, and so it is expected that optimized power efficiencies and the size-effectiveness can be obtained.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.163-165
• /
• 2002

LDD구조를 가진 LDMOS 전력소자의 LDD영역과 채널영역변화에 의한 전기적 특성을 비교 조사하였다. MEDICI 시뮬레이션 tool을 이용하여 hot-carrier전류의 특성, ON 저항의 변화, breakdown 전압의 특성과 switch transient 특성을 조사하였다. Gate-drain 사이의 불순물도핑 영역 및 농도에 따른 소자의 특성해석은 LDD구조를 가진 LDMOS가 hot-carrier resistance 및 전력소모 관점에서 우수한 특성을 나타낼 것으로 사료된다