• The Journal of Pediatrics of Korean Medicine
• /
• v.28 no.2
• /
• pp.88-102
• /
• 2014

Objectives This study is to know the current usage of Ha-Taedok Method in Korean pediatrician. Methods 69 questionnaires were statistically analyzed by using PASW Statistics 18. Results 55 Korean Medicine doctors knew Ha-Taedok Method, but only 2 doctors were using Ha-Taedok Method in their practice. The doctors tend not to use Ha-Taedok Method because it was hard to get permission from the patient's caregiver. 11 Korean Medicine doctors used Ha-Taedok Method to their own children though. The pediatricians felt satisfied from the effect of Ha-Taedok Method especially because it can prevent from disease. They reported no side effect and adverse effect. Coptidis Rhizoma is a preferred herb to use along with Ha-Taedok Method. For a better result from Ha-Taedok Method, it is recommended to start within 3 days old of patient. Conclusions Ha-Taedok Method may be effective as preventive method.

• Proceedings of the KSR Conference
• /
• 2001.05a
• /
• pp.249-256
• /
• 2001

This study investigated the shear stiffness of level of small strain with time effect. Time effect consists of rest time, loading rate of recent and current stress path. In addition, for the measurement of small strain, overconsolidated state was represented in a triaxial cell, and drained stress path tests were carried out. Test results show that the loading rate of recent stress path has no effects on the stiffness of very small strain, but the shear stiffness of level of small strain increases with it. Finally, the rest time and the loading rate of current stress path have the effects on the shear stiffness of initial and small strain.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.1
• /
• pp.49-57
• /
• 2016

A modular multilevel converter is widely adapted for a high-voltage direct current power transmission system. This study proposes a design methodology for a novel digital control that mitigates the negative effects caused by time delay, including communication transport delay for a modular multilevel converter. The modeling and negative effect of time delay are analyzed theoretically in a frequency domain, and its compensation methodology based on an inverse model is described fully with practical considerations. The proposed methodology is verified through several simulation results using a modular 21-level converter system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05a
• /
• pp.17-22
• /
• 2003

HTS superconducting tapes are now commercially available for practical applications such as magnets and cables. Since superconductors in such applications are subjected to high mechanical loads that can significantly degrade the superconducting properties, mechanical properties and the strain tolerance known as the strain effect on superconducting properties are needed to be estimated for developing superconducting devices. The progress in technology achieved in the field of strain effect evaluation on the critical current of HTS tapes in various deformation modes is discussed in this study.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.4
• /
• pp.170-173
• /
• 2007

Organic field-effect transistors (OFETs) are of interest for use in widely area electronic applications. We fabricated the organic field-effect transistor based a copper phthalocyanine (CuPc) as an active layer on the silicon substrate. The CuPc FET device was made a topcontact type and the substrate temperature was room temperature and $150^{\circ}C$. The CuPc thickness was 40 nm, and the channel length was $50{\mu}m$, channel width was 3 mm. We observed the typical current-voltage (I-V) characteristics and capacitance-voltage (C-V) in CuPc FET and we calculated the effective mobility with each device. Also, we observed the AFM images with different substrate temperature.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.1
• /
• pp.40-42
• /
• 2011

An organic field-effect transistor (OFET) was fabricated using a copper phthalocyanine (CuPc) as the active layer on the silicon substrate. The CuPc FET device was configured as a top-contact type. The substrate temperature was room temperature. The CuPc thickness was 40 nm, and the channel length and channel width were 100 ${\mu}m$ 3 mm, respectively. Typical current-voltage (I-V) characteristics of the CuPc FET were observed and subsequently compared to the UV/ozone treatment on substrate surface.

• Journal of Power Electronics
• /
• v.15 no.2
• /
• pp.431-442
• /
• 2015

Dead-time element must be set into space vector pulsed width modulation signals to avoid short circuits of the inverter. However, the dead-time element distorts the output voltage vector, which deteriorates the performance of electrical machine drive system. In this paper, dead-time effect and its compensation control strategy are analyzed. Based on the analysis, the voltage distortion caused by dead-time is regarded as two disturbances imposed on dq axes in the rotor reference frame, which degenerates the current tracking performance. To inhibit the adverse effect caused by the dead-time, a control scheme using two linear extended state observers is proposed. This method provides a strong ability to suppress dead-time effects. Simulations and experiments are conducted on a permanent magnet synchronous motor drive system to demonstrate the effectiveness of the proposed method.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.739-744
• /
• 2001

In order to investigate the stability of magneto-rheological fluid based squeeze film damper (MR-SFD), its negative stiffness effect, which arises from magnetization of MR-SFD, is identified theoretically and experimentally. The analytical model of MR-SFD includes the magnetic circuit as well as the displacement stiffness associated with the squeeze mode of MRF. Extensive experiments are carried out to measure the magnetic attraction forces generated in the MR-SFD, with the excitation frequency and the eccentricity of the journal varied, which are controlled by an active magnetic bearing. The simulation and experimental results are found to be in good agreement. It is concluded that the negative stiffness effect dominates only in the low frequency region because its effect diminishes in the high frequency region due to the eddy-current loss.

• Journal of Korean Society on Water Environment
• /
• v.27 no.1
• /
• pp.54-60
• /
• 2011

To evaluate the feasibility of electrodialysis for copper removal from industrial wastewater, the effect of operating parameters on the removal of copper was experimentally estimated. The limiting current density (LCD) linearly increased with the copper concentration and the flow rate. The time when the copper concentration of diluate reaches to 3 mg/L was linearly proportional to initial concentration of diluate, and the concentration of concentrate did not affect the removal rate. Increase in the flow rate gave a positive effect on the removal rate and became insignificant at flow rates greater than 2.4 L/min. The removal rate increased with the applied voltage. From the operation of the electrodialysis module used in this research, the flow rate of 2.4 L/min and the voltage corresponding to the 80~90% of LCD were found be the optimum operating condition for the copper removal from highly concentrated copper solutions.

• Steel and Composite Structures
• /
• v.38 no.2
• /
• pp.141-150
• /
• 2021

In the present paper we have investigated the Stoneley wave propagation at the interface of two dissimilar homogeneous nonlocal magneto-thermoelastic media under the effect of hall current applied to multi-dual-phase lag heat transfer. The secular equations of Stoneley waves have been derived by using appropriate boundary conditions. The wave characteristics such as attenuation coefficients, temperature distribution and phase velocity are computed and have been depicted graphically. Effect of nonlocal parameter and hall effect are studied on the attenuation coefficient, phase velocity, temperature distribution change, stress component and displacement component. Also, some particular cases have been discussed from the present study.