• Bulletin of the Korean Space Science Society
• /
• 2007.10a
• /
• pp.55-55
• /
• 2007

• International Journal of Aeronautical and Space Sciences
• /
• v.4 no.1
• /
• pp.1-8
• /
• 2003

In this paper, a reconfigurable flight control system is designed by applying the sliding mode control scheme. The sliding mode control method is a nonlinear control method which has been widely used because of its merits such as robustness and flexibility. In the sliding mode controller design, the signum function is usually included, but it causes the undesirable chattering problem. The chattering phenomenon can be avoided by using the saturation function instead of signum function. However, the boundary layer of the sliding surface should be carefully treated because of the use of the saturation function. In contrast to the conventional approaches, the thickness of the boundary layer of our approach does not need to be small. The reachability to the boundary layer is guaranteed by the sliding mode controller. The fault detection and isolation process is operated based on a sliding mode observer. To evaluate the reconfiguration performance, a numerical simulation using six degree-of-freedom aircraft dynamics is performed.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.53 no.4
• /
• pp.235-245
• /
• 2004

In this paper, fault tolerant mechanisms are presented for a servo manipulator system designed to operate in a hot cell. A hot cell is a sealed and shielded room to handle radioactive materials, and it is dangerous for people to work in the hot cell. So, remote operations are necessary to handle the radioactive materials in the hot cell. KAERI has developed a servo manipulator system to perform such remote operations. However, since electric components such as servo motors may fail by radiation, fault tolerant mechanisms have to be considered. For fault tolerance of the servo manipulator system, duplication mechanism increasing the reliability of the transport's driving motors and reconfiguration algorithm accommodating the slave's motor failure have been presented. The reconfiguration algorithm recovering the end effector's motion in spite of one motor's failure is based on control allocation redistributing redundant axes. The constrained optimization method and pseudo inverse method have been adopted for control allocation. Simulation examples and real test results have been presented to verify the Proposed methods.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.4
• /
• pp.318-330
• /
• 2013

This paper presents a high-linearity low-noise small-size programmable gain amplifier (PGA) based on a new low-noise low-distortion differential amplifier and a proposed reconfiguration technique. The proposed differential amplifier combines an inverter-based differential pair with an adaptive biasing circuit to reduce noise and distortion. The reconfiguration technique saves the chip size by half by utilizing the same differential pair for the input transconductance and load-stage, interchangeably. Fabricated in $0.18-{\mu}m$ CMOS, the proposed PGA shows a dB-linear control range of 21dB in 16 steps from -11 dB to 10 dB with a gain error of less than ${\pm}0.33$ dB, an IIP3 of 7.4~14.5 dBm, a P1dB of -7~1.2 dBm, a noise figure of 13dB, and a 3-dB bandwidth of 270MHz at the maximum gain, respectively. The PGA occupies a chip area of $0.04mm^2$ and consumes only 1.3 mA from the 1.8 V supply.

• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.204-209
• /
• 2003

Recently, The TCN(Train Communication Network} as the distributed control systems for electric vehicles, which is the international standard of the intra vehicle communication, actively recognizes variations and supports reconfiguration of the train network when a vehicle is separated or recombined. The technique of reconfiguration to take variety and interoperability of a vehicle constitution is used when the vehicle constitution is changed. At the time, each node making up vehicle network shares the information about the variation of vehicle constitutions and the state of nodes. In the hierarchical TCN structure, an exchange of data becomes available as a work to transmit information between components is performed at the node playing a role of gateway. This paper proposes a protocol to transmit the information of the train reconfiguration. The protocol gives an application to renew a list for transmitting information and to perform the transmission that can guarantee periodic and non-periodic data transmission between nodes when the network nodes changed by a variation of the network state are reconfigured. If use this protocol, can use functions that are offered in the electric railcar at the same time that composition of vehicles is completed without delay. And when driver of the electric railcar inspect before running of vehicles, can confirm state of vehicles visually through monitor in driver's room.

• Journal of the Korea Society for Simulation
• /
• v.22 no.2
• /
• pp.1-10
• /
• 2013

Modeling and simulation techniques construct experimental environment considering battlefields and are able to analyze performance of components of weapon system that closely resemble reality. However, developed model has low scalability and not cared reusability because it has been used only in a limited range of domain. In this paper, we develop a verification tool to verify reusability of developed component for dynamic reconfiguration and to judge scalability of it and a management tool to control data of it effectively. In addition, dynamic reconfiguration architecture of guided weapon systems designed in the previous study has been applied to SAM(Surface to Air Missile) System Simulator, and we study effectiveness of the developed component. Thus the user can configure various guided weapon systems through simulation application of dynamic reconfiguration architecture of component.

• 한국HCI학회:학술대회논문집
• /
• 2006.02a
• /
• pp.747-752
• /
• 2006

유비쿼터스 환경에서 사용자는 언제 어디서나 주변에 편재하는 컴퓨팅 장치나 서비스를 활용하여 자신이 필요로 하는 작업을 수행할 수 있다. 이러한 컴퓨팅 장치와 서비스를 제어하기 위한 표준으로서 UPnP(Universal Plug and Play)가 각광을 받고 있다. 하지만, 기존에 개발된 UPnP 장치의 원격 제어 프로그램은 사용자의 상황 정보, 선호도 및 접근 권한에 관계없이 동일한 사용자 인터페이스를 제공하기 때문에 사용자에게 편의를 제공하는데 있어 한계가 있다. 본 논문에서는 이러한 단점을 극복하기 위하여 개발된 개인화 및 상황 인지를 지원하는UPnP 장치 원격 제어 프로그램의 설계 및 구현에 대해 기술한다. 제안된 원격 제어 프로그램은 사용자의 상황, 선호도 및 접근 권한에 따라 사용자 인터페이스(User Interface, UI)가 동적으로 생성되고 재구성된다. 또한 이러한 UI 개발의 편의성을 위하여 UPnP 장치 기술(description)에 따라 UI를 자동으로 생성하는 방법에 대해서도 기술한다.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.29B no.4
• /
• pp.22-30
• /
• 1992

A redundant control scheme which can maintain its tracking capability in the case of a controller failure is proposed for the industrial applications which need high reliability with fault-tolerance. It consists of two identical controllers and a switching mechanism which includes failure detection and reconfiguration algorithm. The new detection method against controller failure using fuzzy logic enables the detection of controller failures without failure assumptions through the instability of the failed controller. The failed controller is smoothly removed from the control loop by reducing time weight of the failed controller.

• International Journal of Control, Automation, and Systems
• /
• v.6 no.3
• /
• pp.296-305
• /
• 2008

Whereas fault diagnosis has been the subject of intensive research since the 1970s, the design of fault tolerant systems is a recent research field which does not set its foundations in a unified framework and does not use a unified vocabulary. As a contribution to this special issue, this paper proposes an ontology for the problem of Fault Handling, that embeds the problem of Fault Tolerance.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.2
• /
• pp.164-171
• /
• 2006

In this paper, the fault tolerant system for BLDC motor has been proposed to maintain control performance under an open switch fault of inverter. The fault identification is proposed to two methods, which are using the difference between reference and actual current, and adding voltage sensors across lower legs of inverter. The reconfiguration scheme is achieved by the four-switch topology connecting a faulty leg to the middle point of DC-link using bidirectional switches. The proposed fault tolerant system quickly recovers control performance by short fault detecting time and reconfiguration of system topology. Therefore, continuous free operation of the BLDC motor drive system after faults is available. The superior performance of the proposed fault tolerant system is proved by simulation.