• Bulletin of the Korean Chemical Society
• /
• v.23 no.11
• /
• pp.1541-1544
• /
• 2002

The concentration of B in steels is important due to its influence on mechanical properties of steel such as hardenability, hot workability, and creep resistance. An analytical method has been developed to determine B in steel samples by high-resolution inductively coupled plasma mass spectrometry (HR-ICP-MS). National Institute of Standard and Technology Standard Reference Material (NIST SRM) 348a was analyzed to validate the analytical method. The steel sample was digested in a centrifuge bottle with addition of aqua regia and $^{10}B$ spike isotope. Sample pH was then adjusted to higher than 10 to precipitate most matrix elements such as Fe, Cr, and Ni. After centrifugation, the supernatant solution was passed through a cation exchange column to enhance the matrix separation efficiency. B recovery efficiency was about 37%, while matrix removal efficiency was higher than 99.9% for major matrix elements. The isotope dilution method was used for quantification and the determined B concentration was in good agreement with the certified value.

• Journal of Welding and Joining
• /
• v.6 no.3
• /
• pp.27-36
• /
• 1988

In fabrication of various welded structures made of high strength steels, the occurence of hydrogen assisted cracking and embrittlement in HAZ is prime importance. The present work was carried out to clarify the effect of chemical compositions, especially B and/or Ti addition on the cold cracking susceptibility and HAZ embrittlement in low crabon equivalent steel. Tests results showed that the addtio of optimum boron content in steel with low Pem value i.e., below 0.20 % was the best way to improve the weldability as well as the mechanicla properties of $60kg/mm^2$ grade quenched and tempered high strength steels.

• Journal of Korean Vacuum Science & Technology
• /
• v.1 no.1
• /
• pp.1-12
• /
• 1997

A new three-dimensional (3D) Monte Carlo ion implantation simulator, TRICSI, has been developed to investigate 3D mask effects in the typical mask structure for ion implantation into crystalline silicon. We present the mask corner and mask size effects of implanted boron range profiles, and also show the calculated damage distributions by applying the modified Kinchin-Pease equation in the single-crystal silicon target. The simulator calculates accurately and efficiently the implanted-boron range profiles under the relatively large implanted area, using a newly developed search algorithm for the collision partner in the single-crystal silicon. All of the typical implant parameters such as dose, tilt and rotation angles, in addition to energy can be used for the 3D simulation of ion implantation.

• Journal of Korea Foundry Society
• /
• v.9 no.4
• /
• pp.311-319
• /
• 1989

The effects of the alloying elements and cooling rates on the formation of phosphide eutectics of compacted vermicular graphite cast irons containing copper, tin, molybdenum for producing pearlitic matrix, and also containing phosphorus and boron for increasing wear resistance, were investigated. The liquidus phosphide eutectic was found to solidify as a pseudo-binary phosphide eutectic, but with increasing of the cooling rate non-equlibrium phosphide eutectic with needle type carbide could be formed. However, the liquidus phosphide eutectic containing both phosphorus and carbide-forming boron was found to solidify always as a non-equlibrium phosphide eutectic with coarse carbide, independent from the cooling rate. It was also confirmed that the tiny isolated phase observed by SEM was gamma iron solid solution with phosphorus, silicon, molybdenum and the matrix containing these tiny islands was phosphide phase containing manganese and molybdenum. The addition of copper was found to decrease the tendency of forming ledeburitic carbides in the phosphide eutectic.

• Journal of Magnetics
• /
• v.4 no.1
• /
• pp.10-12
• /
• 1999

We report the salient features of the magnetic properties of amorphous$ Fe_{84-x}Nb_7B_{8+x}Cu_1$ (x=0, 1, 4) alloys. The study of dc-magnetization properties and the ac-susceptibility was carried out. The temperature dependence of the magnetization follows the predictions of spin wave excitations with long wavelengths. Especially, the addition of boron modifies the magnetic properties: the spin wave stiffness increases from 56.8 to 65.7 meV$\AA$2 and Curie temperature increases from 298 K to 352 K. This result indicates a magnetic hardening of the exchange interaction by higher exchange energy. Thus, the substitution of iron by boron favours the increase of magnetic order in this system.

• Journal of Welding and Joining
• /
• v.7 no.1
• /
• pp.59-66
• /
• 1989

The weldability and joint performance were evaluated for newly developed 60kg/mm$\^$2/ steel which had low cold cracking susceptibility. The main results obtained were as follows; In case of quenched and tempered 60kg/mm$\^$2/ steels, it was very effective to improve weldability and joint performance by lowering carbon and Pcm level. Very small addition of about 0.001 to 0.002wt% boron exhibited an appreciable compensation effect on strength which was decreased by lowering carbon and Pcm level. As a result, the newly developed steel was able to be welded without preheating and exhibited superior joint performance to conventional steels.

• Journal of Ceramic Processing Research
• /
• v.17 no.7
• /
• pp.763-767
• /
• 2016

The structural characterization of cubic boron nitride (c-BN) thin films was performed using a B4C target in a radio-frequency magnetron sputtering system. The deposition processing conditions, including the substrate bias voltage, substrate temperature, and base pressure were varied. Fourier-transform infrared spectroscopy and X-ray photoelectron spectroscopy were used to analyze the crystal structures and chemical binding energy of the films. For the BN film deposited at room temperature, c-BN was formed in the substrate bias voltage range of -400 V to -600 V. Less c-BN fraction was observed as the deposition temperature increased, and more c-BN fraction was observed as the base pressure increased.

• Journal of the Korean institute of surface engineering
• /
• v.28 no.2
• /
• pp.110-118
• /
• 1995

The effect of reductants (Ti, Si, Al, Mn, Fe) addition into molten Borax has been studied on oxidation resistance and the growth of boronized layer formed during electro-boronizing on the substrate such as carbon steel and STS 430. Experiments have been carried out at the current density of 0.5 A/$\cm^2$ and in temperature range of 600~$1000^{\circ}C$ for 1~5 hours. The penetrated depth of the boron increased with addition of reductants (Ti, Si, Al) and decreased with addition of Mn and Fe. But excessive addition of reductants inhibited the boronizing due to an increase in viscosity of electrolyte. Oxidation resistance of the boronized carbon steel was improved but that of the boronized STS 430 decreased.

• Journal of the Korean Electrochemical Society
• /
• v.5 no.1
• /
• pp.30-38
• /
• 2002

Disordered carbon and boron-substituted disordered carbons $C_{l-x}B_x(x=0.05,\;0.10,\;0.20)$ were synthesized by Pyrolysis of LPG(liquid Propane gas)and $BCl_3$. Their electrochemical properties as anode materials for Li-ion secondary batteries were then investigated. When PVDF is added to the sample in a weight ratio 5 : 95, the disordered carbon with x=0.00 had the first discharge capacity 374 mAh/g. Its cycling performance was relatively good from the second cycle and it had the discharge capacity 258 mAh/g at the 10th cycle. When PVDF is added to the sample in a weight ratio 5 : 95, the sample with x=0.05 among the samples $C_{l-x}B_x(x=0.05,\;0.10,\;0.20)$ exhibited the largest first discharge capacity 860 mAh/g and discharge capacity 181 mAh/g at the 10th cycle. All the samples had similar cycling performances from the second cycle. The sample $C_{0.90}B_{0.10}$ showed the best electrochemical properties as a anode materials fur Li-ion secondary battery from the view points of the first discharge capacity(853 mAh/g when $10w1.\%$ PVDF is used), cycling performance, discharge capacity(400mAh/g at the 10th cycle when $10wt.\%$ PVDF is used). All the samples showed generally larger charge and discharge capacities when $10wt.\%$ PVDF ratter than $5wt.\%$ PVDF is used. The plateau region in the range of voltage lower than 1.25V becomes larger probably since the structure becomes less disordered by the addition of boron. When boron is added, the charge and discharge capacities decreased suddenly at the second cycle. This may be become only a part of Li are reversibly deintercalated and intercalated and a part of Li which are strongly combined with B are not deintercalated. The increases in charge and discharge capacities are considered to be resulted from the increase in the potential of Li in the boron-added carbons, caused by the strengthening of the chemical bond between the intercalated Li and the boron-carbon host since the boron acts as electron acceptor.

• Fire Science and Engineering
• /
• v.32 no.2
• /
• pp.1-6
• /
• 2018

The combustion characteristics of cypress wood coated with boric acid (BA) and ammonium pentaborate (APB) were examined using a cone calorimeter according to the ISO 5660-1 standard. As a result, the combined specimens of boric acid and ammonium pentaborate (BA/APB) led to an improved fire performance index due to their synergistic effect. In addition, the total heat release values of the specimen coated with the boron compounds were 6.1~14.1% lower than that of the base specimen. The total smoke release rate (TSR) of the specimens coated with the boron compound decreased throughout the combustion process, except for BA/APB. The maximum concentration of carbon monoxide was reduced by 15.8~25.5%. In general, wood treated with flame retardants has a lower fire hazard.