• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.1701-1703
• /
• 2006

Here we describe a novel driving scheme in the form of negative AC bias stress (NAC) to compensate shift in the threshold voltage for hydrogenated amorphous silicon (${\alpha}$-Si:H) thin film transistor (TFT) for AMOLED applications. This scheme preserves the threshold voltage shift of ${\alpha}$-Si:H TFT for infinitely long duration of time(>30,000 hours) and thereby overall performance, without using any additional TFTs for compensation. We briefly describe about the possible driving schemes in order to implement for real time AMOLED applications. We attribute most of the results based on concept of plugging holes and electrons across the interface of the gate insulator in a controlled manner.

• Transactions on Electrical and Electronic Materials
• /
• 제11권5호
• /
• pp.202-205
• /
• 2010

In this study, the etch properties of $Al_2O_3$ thin films deposited by atomic layer deposition were investigated as a function of the $O_2$ content in $BCl_3$/Ar inductively coupled plasma. The experiments were performed by comparing the etch rates and selectivity of $Al_2O_3$ over the hard mask materials as functions of the input plasma parameters, such as the gas mixing ratio, DC-bias voltage, ratio-frequency (RF) power and process pressure. The highest obtained etch rate was 477 nm/min at an RF power of 700 W, $O_2$ to $BCl_3$/Ar gas ratio of 15%, DC-bias voltage of -100 V and process pressure of 15 mTorr. The deposition occurred on the surfaces when the amount of $O_2$ added to the $BCl_3$/Ar gas was too high at a low DC-bias voltage or high process pressure. X-ray photoelectron spectroscopy was used to investigate the chemical reactions on the etched surface.

• 열처리공학회지
• /
• 제20권2호
• /
• pp.78-83
• /
• 2007

CrN coatings were deposited by cathodic arc ion plating method on the SKD11 steel substrates. Atmosphere temperature of $350^{\circ}C$, arc current of 90 A, nitrogen partial pressure of 1.0-5.3 Pa, and negative bias voltage of 30-135 V were selected. The characteristics of microstructure were investigated with XRD. Hardness, adhesion and friction coefficient measured by microhardness tester, scratch tester, and ball on disk tribometer. Microstructures depended on nitrogen partial pressure and bias voltage. The preferred orientation of the films was changed from (200) to (111) with decreasing pressure and increasing bias voltage. Adhesion properties related with microstructure, but microstructure changes slightly influenced on hardness and friction properties. The critical load.($Lc_1$) and hardness of CrN films deposited at 5.3 Pa, -30 V condition were 55 N(HF1), $2157{\pm}47\;Hk_{0.025}$. The friction coefficient were about 0.5 under dry condition.

• 한국산학기술학회논문지
• /
• 제11권5호
• /
• pp.1592-1596
• /
• 2010

IGZO (indium gallium zinc oxide) 박막트랜지스터는, 활성층 채널의 폭과 길이의 비가 고정된 경우에도, 채널 길이가 길어지면 게이트전압에 대한 드레인 전류의 특성곡선이 양의 전압 방향으로 이동하고 전계효과이동도는 낮아졌다. 채널의 길이와 폭이 고정된 상태에서는, 드레인이 전압 높은 경우에 전계효과이동도가 낮고 문턱아래 기울기가 큰 특성을 보였다. 이러한 현상은 IGZO 채널층의 일함수가 커서 소스/드레인 전극과 채널층의 접합부 띠굽음이 규소반도체의 경우와 반대방향으로 나타나는 것에 기인하는 것으로 해석된다.

• 한국표면공학회지
• /
• 제32권4호
• /
• pp.496-502
• /
• 1999

Electroplating of Ag and Au on the functional area of lead frames are required for good bonding ability in IC packaging. As the patterns of the lead frame become finer, development of new deposition technology has been required for solving problems associated with process control for uniform thickness on selected area. Sputtering was employed to investigate the adhesion between substrate Alloy42 and Ag film as a new candidate process alternative to conventional electroplating. Coating thickness of Ag film was controlled to 3.5$\mu\textrm{m}$ at room temperature as a reference. The deposition of film was optimized to ensure the adhesion by process parameters of substrate heating temperature at $100~300^{\circ}C$, sputter etching time at -300V for 10~30min, bias voltage of -100~-500V, and existence of Cr interlayer film of $500\AA$. The critical $load L_{c}$ /, defined as the minimum load at which initial damage occurs, was the highest up to 29N at bias voltage of -500V by scratch test. AFM surface image and AES depth profile were investigated to analyze the interface. The effect of bias voltage in sputtering was to improve the surface roughness and remove the oxide on Alloy42.

• 한국표면공학회지
• /
• 제32권2호
• /
• pp.93-99
• /
• 1999

Surface polymer layer formed on the silicon wafer during the oxide overetching using $C_4F_8$/ helicon wave plasmas and their characteristics were investigated using spectroscopic elipsometry, X-ray photoelectron spectroscopy, and secondary ion mass spectrometry. Overetch percentage and dc-self bias voltage were varied to investigate the effects on the characteristics of the polymers remaining on the overetched silicon surface. The increase of bias voltage from -80 volts to -120 volts increased the C/F ratio and carbon bondings such as C-C, $C-CF_x$/, and C-Si in the polymer while reducing the thickness of the polymer layer. However, the increase of the overetch percentage from 50% to 100% did not change the composition of the polymer layer and the carbon bondings in the polymer layer remained same even though it increased the polymer thickness. The polymer layer formed at the higher dc-self bias voltage was more difficult to be removed by the following various post-etch treatments compared to that formed at the longer overetch percentage.

• Transactions on Electrical and Electronic Materials
• /
• 제14권2호
• /
• pp.67-70
• /
• 2013

In this study, we changed the input parameters (gas mixing ratio, RF power, DC bias voltage, and process pressure), and then monitored the effect on TiN etch rate and selectivity with $SiO_2$. When the RF power, DC-bias voltage, and process pressure were fixed at 700 W, - 150 V, and 15 mTorr, the etch rate of TiN increased with increasing $CF_4$ content from 0 to 20 % in $CF_4$/Ar plasma. The TiN etch rate reached maximum at 20% $CF_4$ addition. As RF power, DC bias voltage, and process pressure increased, all ranges of etch rates for TiN thin films showed increasing trends. The analysis of x-ray photoelectron spectroscopy (XPS) was carried out to investigate the chemical reactions between the surfaces of TiN and etch species. Based on experimental data, ion-assisted chemical etching was proposed as the main etch mechanism for TiN thin films in $CF_4$/Ar plasma.

• 한국재료학회지
• /
• 제10권3호
• /
• pp.179-183
• /
• 2000

$BCI_3/H_2/Ar$ ICP(Inductively Coupled Plasma)를 이용한 GaN이 건식식각에 있어서 공정변수들이 식각 특성에 미치는 영향을 분석하고 적정조건을 도출하였다. 연구 결과 식각속도와 측벽수직도 공히 ICP 전력, bias 전압과 $BCI_3$ 조성의 증가, 공정압력의 감소에 의해 현저히 증가하며, 온도의 증가에 따라 다소간 증가하였고, 온도의 증가에 따라 다소간 증가하였고, $BCI_3$조성이 가장 큰 영향을 미쳤다. 표면거칠기는 bias 전압 증가에 의해 크게 향상, $BCI_3$ 조성의 감소에 따라 향상되었으며 다른 변수는 큰 영향을 미치지 않았다. 결과적으로 ICP 전력 900W, bias 전압 400V, $BCI_3$ 조성 60%, 공정압력 4mTorr의 조건에서 175nm/min 정도의 $CI_2$ 사용 시와 유사한 높은 식각속도와 평탄한 표면이 얻어졌다. Bias 전압이 낮은 경우 식각 후 시료 표면에 $GaC_x$로 추정되는 식각부산물이 관찰되었다.

• 한국표면공학회지
• /
• 제28권6호
• /
• pp.343-351
• /
• 1995

Titanium nitride films have been prepared on various substrates (silicon wafer, HSS) by cathode arc ion plating process to measure microhardness, adhesion and wear-resistant behaviors by changing the substrate bias voltages (0∼-300V), thickness and roughness. Microhardnesses were measured by micro vickers hardness tester, the adhesion strengths were evaluated by acoustic signals through the scratch test with incremental applied load. As the substrate bias voltages were increased, the ｛111｝ orientation was predominant, the microhardnesses and adhesion strengths of tool steel were observed to be stronger than those of without subatrate bias voltage. Adhesion strengths of the substrate bias were 4-7 times higher than those of without the substrate bias, confirmed by SEM with EDX. Wear resistances were used pin-on-disk tribotester and TiN costing reduced the abrasive wear. As the substrate bias was increased, the weight loss and the friction coefficient was decreased.

• 한국재료학회지
• /
• 제26권8호
• /
• pp.412-416
• /
• 2016

The electrical properties of Au/n-type Ge Schottky contacts with different contact areas were investigated using current-voltage (I-V) measurements. Analyses of the reverse bias current characteristics showed that the Poole-Frenkel effect became strong with decreasing contact area. The contribution of the perimeter current density to the total current density was found to increase with increasing reverse bias voltage. Fitting of the forward bias I-V characteristics by considering various transport models revealed that the tunneling current is dominant in the low forward bias region. The contributions of both the thermionic emission (TE) and the generation-recombination (GR) currents to the total current were similar regardless of the contact area, indicating that these currents mainly flow through the bulk region. In contrast, the contribution of the tunneling current to the total current increased with decreasing contact area. The largest $E_{00}$ value (related to tunneling probability) for the smallest contact area was associated with higher tunneling effect.