• Wind and Structures
• /
• v.36 no.4
• /
• pp.249-261
• /
• 2023

Aerodynamic force coefficients are generally prescribed by an ensemble average of ten and/or twenty 10-minute samples. However, this makes it difficult to identify the exact probability distribution and exceedance probability of the prescribed values. In this study, 12,600 10-minute samples on three tall buildings were measured, and the probability distributions were first identified and the aerodynamic force coefficients corresponding to the specific non-exceedance probabilities (cumulative probabilities) of wind load were then evaluated. It was found that the probability distributions of the mean and fluctuating aerodynamic force coefficients followed a normal distribution. The ratios of aerodynamic force coefficients corresponding to the specific non-exceedance probabilities (C_f,Non) to the ensemble average of 12,600 samples (C_f,Ens), which was defined as an adjusting factor (C_f,Non/C_f,Ens), were less than 2%. The effect of coefficient of variation of wind speed on the adjusting factor is larger than that of the annual non-exceedance probability of wind load. The non-exceedance probabilities of the aerodynamic force coefficient is between P_C,nonex = 50% and 60% regardless of force components and aspect ratios. The adjusting factors from the Gumbel distribution were larger than those from the normal distribution.

• Journal of the Korea Concrete Institute
• /
• v.25 no.4
• /
• pp.429-438
• /
• 2013

An object oriented numerical analysis program of axial-flexural elements and the step-by-step method (SSM) has been developed to analyze concrete long-term behaviors of structures constrained internally and externally. The results of the numerical analysis for simple and continuous prestressed (PS) concrete box and composite girders, pre-cast slab of continuous steel composite girder, and simple preflex composite girder show that the adjusting coefficient decreases by increasing constraint. The loss rates of pre-tension force were not sensitive but those of pre-compression force were increased rapidly by decreasing adjusting coefficient. This indicates that the design based on the loss rate of pre-tension can over-estimate the pre-compression force in a concrete section constrained internally and externally. The adjusting coefficients which satisfy results of the numerical analysis are 0.35~0.95, and it can be used as an index of constraint of concrete long-term deformation. The adjusting coefficient 0.5 of Bridge Design Specifications can under-estimate residual stress of PS concrete slab, and the coefficient 0.7 or 0.8 of LRFD Bridge Designing Specifications can under-estimate the loss rates of continuous PS concrete girders. The adjusting coefficient of hybrid structures should be less then 0.4.

• Proceedings of the KIPE Conference
• /
• 1996.06a
• /
• pp.47-51
• /
• 1996

In this paper, we propose a method for compliance control of a SCARA type 2-freedom direct drive(DD) manipulator. Each joint of the manipulator is driven by a travelling ultrasonic motor(USM). The travelling USM has good some characteristics over conventional servo motors such as compact size, light weight, silent motion, high torque and high speed response. By controlling the elasticity and viscosity of robot joints, a robot can work in compliance with external environment. we control the elastic coefficient and the viscous coefficient of joint by adjusting the phase difference of the motor power. And we contemplate transient response of USM with adjusting the elastic coefficient and the viscous coefficient. To use the result, we can control the robot to reach its goal with compliance motion. It remains for further research to develop the impedance control of USM.

• Current Optics and Photonics
• /
• v.5 no.2
• /
• pp.191-197
• /
• 2021

The anomalous propagation characteristics of a single Airy beam in nonlocal nonlinear medium are investigated by utilizing the split-step Fourier-transform method. We show that besides the normal straight propagation trajectory, the breathing solitons formed by the interaction between Airy beam and nonlocal nonlinear medium can propagate along the sinusoidal trajectory, and the anomalous trajectory can be modulated arbitrarily by altering the initial amplitude and the nonlocal nonlinear coefficient. In addition, the initial amplitude and the nonlocal nonlinear coefficient can have inverse impacts on the formation and transformation of the equilibrium state of spatial solitons, when the two parameters are larger than certain values. Therefore, the reversible transformation of the evolution dynamics of two soliton states can be realized by adjusting those two parameters properly. Finally, it is shown that the propagation properties of the solitons formed by the interaction between Airy beam and nonlocal nonlinear medium can be controlled arbitrarily, by adjusting the distribution factor and nonlocal coefficient.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.11 no.2
• /
• pp.107-115
• /
• 1999

In order to develop a convenient method for the estimation of transport distance of settling stones in quiescent water or flowing water, introduced was the simple but relatively accurate equation of drag coefficient. The equation of drag coefficient introduced was confirmed to give relatively accurate evaluation for the drag force of smooth-surface sphere, and the effects of surface roughness and shape can be considered by adjusting empirical parameters. A theoretical equation has been developed for the settling velocity or settling distance of smooth-surface sphere in quiescent fluid, and the computation results have been obtained by adjusting the empirical parameter for the settling distance of stone in quiescent water. The 2nd order ordinary differential equation has been developed for the case of settling stones in flowing fluid, and a numerical model has been developed by using Runge-Kutta method for its solution. A number of cases have been tested by adjusting the empirical parameter.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.467-470
• /
• 2002

The offects of a small control rod (d=3mm) located near a main circular cylinder on the drag reduction and wake structure modification were investigated. The location of the small control rod mounted on a rod-like spring is self-adjusting according to the wake structure far optimal control of the flow around the main cylinder. The experiments were carried out at the Reynolds numbers based on the cylinder diameter (D=50mm) in the range $Re_{D}=1{\times}10^4{\~}6{\times}10^4$. Mean velocity and turbulent statistics were measured with varying the angle along the cylinder circumference ${\Theta}=15^{\circ},\;30^{\circ},\;45^{\circ}$ and the distance between the main and control rods L =0.7, 1. Compared with the bare cylinder, the main circular cylinder with the fixed and self-adjusting rods reduced drag coefficient by $10{\%}$ at the angle of ${\Theta}=45^{\circ}$. For the main cylinder with self-adjusting rot as the Reynolds numbers increase, the streamwise mean velocity is increased, however, the turbulence intensity is decreased. In addition, the control rods tested in this study are effective at higher Reynolds number than at lower Reynolds number.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.11
• /
• pp.84-90
• /
• 2010

In this paper, the reduced size of broad bandpass filter with parallel coupled line structure is presented. This proposed filter can control bandwidth of narrow to broadband by adjusting the coupling coefficient. The conventional filter is operated with a narrow band. If a higher bandwidth is desired than the conventional narrow bandwidth, it is hard to realize due to the coupling coefficient between feeding line and resonator. In this paper, to overcome this limitation, a proposed bandpass filter is designed with reduced size due to SIR(Stepped Impedance Resonator) and multi-grade type structures than conventional one, and it has characteristics of adjusting bandwidth freely as per quantity of coupling coefficient. The proposed bandpass filter that, experimental results of insertion and return losses are 0.42 dB and 20.9 dB with bandwidth of 60 % at the center frequency of 5.8 GHz, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.4A
• /
• pp.407-413
• /
• 2011

In this paper, the reduced size of broad bandpass filter with parallel coupled line structure is presented. This proposed filter can control bandwidth of narrow to broadband by adjusting the coupling coefficient. The conventional filter is operated with a narrow band. If a higher bandwidth is desired than the conventional narrow bandwidth, it is hard to realize due to the coupling coefficient between feeding line and resonator. In this paper, to overcome this limitation, a proposed bandpass filter is designed with reduced size due to SIR (Stepped Impedance Resonator), U-shaped open stub with hair-pin and vertical-type structure than conventional one, and it has characteristics of adjusting bandwidth freely as per quantity of coupling coefficient. The proposed bandpass filter that, experimental results of insertion and return losses are 0.42 dB and 24.5 dB with bandwidth of 60 % at the center frequency of 5.8 GHz, respectively.

• Journal of Drive and Control
• /
• v.20 no.3
• /
• pp.9-14
• /
• 2023

In this paper, the selection of a reliable accelerated life test code for a 2-ton forklift was accomplished by choosing the driving resistance coefficient failure-free test time based on a 10,000-hour B₁₀ life. The overall life and average equivalent load of the vehicle were then calculated based on actual driving test conditions using the selected driving resistance coefficient. The gear train's accelerated life test code was selected by adjusting the equivalent load to a torque and rotation speed that did not exceed 125%(about 75HP) of the vehicle rated power. The safety of the test standards was validated by conducting an actual accelerated life test utilizing the proposed test method in this study and comparing the test result with the corresponding theoretical value. It is anticipated that the reliability of the accelerated life test in this paper will be enhanced, by incorporating actual driving performance data collected directly from the forklift and adjusting the conditions used in developing the accelerated life test code.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.2
• /
• pp.107-111
• /
• 2018

In this study, we designed the temperature coefficient of resistance (TCR) and heat radiation properties of shunt fixed resistors by adjusting the atomic composition of a metal alloy resistor, and fabricated a resistor that satisfied the designed properties. Resistors with similar atomic composition of copper and nickel showed low TCR and excellent shunt fixed resistor properties such as short-time overload, rated load, humidity load, and high temperature load. Finally, we expect that improved sensor accuracy will be obtained in current-distribution-type shunt fixed resistor for IoT sensors by designing the atomic composition of the metal alloy resistor proposed in this work.