• ETRI Journal
• /
• v.34 no.1
• /
• pp.55-65
• /
• 2012

E-voting is expected to offer prominent advantages over traditional voting methods. Advantages include faster tallying, greater accuracy, prevention of void ballots, and lower cost. However, many experts express concerns about the potential for large-scale fraud. Recently, many paper based end-to-end (E2E) voter verifiable systems providing individual verifiability and universal verifiability have been proposed. These systems, unlike previous voting systems, are used in polling booths and without access to trusted computing devices at the time of voting. In this paper, we propose a practical and secure E2E voter verifiable system using a paper receipt based on cryptographic technologies.

• Journal of Welding and Joining
• /
• v.8 no.2
• /
• pp.70-79
• /
• 1990

Stainless clad steels were made through hot rolling process. Backing plates employed in this study were HSLA steel and mild steel. The shear bond strength increased with an increase of the soaking temperature and time. It was also found that the shear bond strength increased with an increase of the reduction ratio. The threshold deformation was observed to be 20% and 10% respectively when the soaking conditions of 15 min. at 900.deg. C and 30 min. at 1000.deg. C were applied. Either the rolling or the transverse direction did not give any significant difference in the shear bond strength. Stainless steel-HSLA steel was superior to stainless steel-mild steel in the same range of magnitude. Because the above experimental results were in contrary to the existing mechanisms, the new model was proposed to describe the bonding mechanism and the void formation.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.717-721
• /
• 2010

Soil volume conversion factors are used for estimation of an excavated the soil volume which will be removed or added in levelling the ground surface of a construction site. An accurate evaluation method will help us reduce a construction cost and time consuming. In this study, we performed the laboratory tests, including grain size measurement, water content, specific gravity, porosity, density and XRD tests, to suggest reliable soil volume conversion factors and weathering indices in field using nondestructive methods. The weathering index and soil volume conversion factor L are obtained for different types of soils. At results, the CIW index is the best method measuring the weathering index and the factor L is relative to natural porosity, void ratio, density and dry density.

• Electrical & Electronic Materials
• /
• v.10 no.3
• /
• pp.247-254
• /
• 1997

Internal voids in insulators give rise to partial discharge, which causes a local breakdown and even entire insulation breakdown. Recently, the necessity of establishing the way to diagnose the aging of insulation materials and to predict of insulation breakdown become important. The purpose of our work are to investigate the treeing phenomena with an artificial needle shaped void by the charge of discharge and acoustic emission pulse in each phase angle area at the same time. We analyzed the .PHI.-QA-t pattern and .PHI.-AEA-t pattern using statistic operators such as pulse magnitude, pulse number, skewness, kurtosis. Therefore, the relation between the charge of discharge and acoustic emission pulse will be helpful to predict the breakdown just before the breakdown occur.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.10a
• /
• pp.155-158
• /
• 2004

In resin transfer molding, the preform similar to product shape is placed into a mold cavity. Rapid flow front without void formation is important for the composites processing. Multi-layered preform of sandwich is selected. Experiments is carried out using redial flow. An analytical modeling is performed and compared with experimental results. Accurate prediction of flow advance in the preform is of use for reducing the time consumption in the process and enhancing product properties of the final part.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1781-1783
• /
• 1996

Recently, the necessity of establishing the way to diagnose the aging of insulation materials and to predict of insulation breakdown become important. The purpose of our work are to investigate the treeing phenomena with a artificial needle shape void by the charge of partial discharge and acoustic emission pulse in each phase angle area at the same time. We have analyzed the ${\Phi}-Q-n$ pattern and the insulation diagnosis of the samples using statistic operators such as charge magnitude and A.E pulse factor, skweness, kurtosis, G,C. Therefore, the relation between the charge of partial discharge and A.E pulse will be helpful and efficient to predict the breakdown just before the breakdown occure.

• Korean Journal of Materials Research
• /
• v.17 no.7
• /
• pp.371-375
• /
• 2007

In-situ observation of electromigration behavior of eutectic SnPb solder was performed as a function of line length at $100^{\circ}C$, $6{\times}10^4A/cm$ condition in a scanning electron microscope chamber. The incubation time for edge drift and the edge drift velocity increase as line length increases, which are discussed with the void nucleation stage of solder bump and the electromigration back flux force, respectively. Finally, the existence of electromigration product (jL) and its line length dependency are also discussed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.05a
• /
• pp.84-89
• /
• 1996

The nucleation and growth of microporosities was observed during the course of annealing treatment of sputter-deposited AgInSbTe thin films. There was a close correlation between the density of microporosity and the sputtering gas pressure in annealed thin films. The void density for a given composition decreased with sputtering gas pressure. It was shown from the present study that the number of porosities decreased while the average porosity size increased as the annealing temperature and holding time increased. The mechanism of porosity formation in the sputter-deposited AgInSbTe thin flus containing Ar-impurity trapped from the Ar-plasma is discussed in the present article.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.11 no.1
• /
• pp.33-38
• /
• 2015

The effects of post weld heat treatment(PWHT) on the mechanical properties of 2.25Cr-1Mo steels were investigated. As the PWHT temperature or holding time increased, the strength of low alloy steels progressively decreased due to softening process. After the conventional PWHT, the strength was larger than the minimum value of materials specification. The Charpy impact energy was hardly affected by the conventional PWHT. The trend of mechanical properties was analyzed in terms of tempering parameter. Most materials replaced from a power plant met the requirements of materials specification except for one heat. Same heat of materials with low impact energy were attributed to the voids formed during casting process.

• Korea-Australia Rheology Journal
• /
• v.18 no.4
• /
• pp.217-224
• /
• 2006

Rapid flow advancement without void formation is essential in the liquid composite molding (LCM) such as resin transfer molding (RTM) and vacuum assisted resin transfer molding (VARTM). A highly permeable layer in multi-layered preform has an important role in improvement of the flow advancement. In this study, a multi-layered preform which consists of three layers is employed. Radial flow experiment is carried out for the multi-layered preform. A new analytic model for advancement of flow front is proposed and effective permeability is defined. The effective permeability for the multi-layered preform is obtained analytically and compared with experimental results. Compaction test is performed to determine the exact fiber volume traction of each layer in the multi-layered preform. Transverse permeability employed in modeling is measured experimentally unlike the previous studies. Accurate prediction of flow advancement is of great use for saving the processing time and enhancing product properties of the final part.